Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 20-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 25-12-2025 |
| 2 | 13-12-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 20-12-2025 |
| Sl. No. | Item Description |
| 1 | Almirah large steel with shelves (Drawing No : FD-1031)DIMENSION:- Overall size shall be 916mm(W)X468mm(D)X1980(H) Shelf thickness-0.7mm, Back thickness-0.8mm, Door thickness-0.8mmDESCRIPTION:-Almirah large steel with shelves The base shall be made of two numbers mild steel sheet channel bases made in U shaped with ends covered. Mild steel sheet shall be 1mm thick. The base channel shall be welded at 50mm from each end of the length of 920mm and shall be up to full width of 485mm and shall be 100mm high Top, side’s bottom and back of almirah shall be of 1mm thick mild steel sheet. Four shelves equally spaced of 1mm thick mild steel sheet shall be provided to make five compartments. Front shutter shall two leaves of equal size .Front shutter leaves shall have three butt hinges of 75mm fixed to each shutter and shall be side hung. All joints and welding and fixing shall be done in accordance with the standard workmanship. Make- GodrejHANDLE: One chromium plated steel handle with a locking device shall be provided as shown on drawing. LOCKING DEVICE: The locking device shall be three way locking device and shall also be provided with decorative key plate .Make of Lock-Harrison/Godrej.FINISH:-All steel surfaces exposed to view when placed in position shall be paintedwith two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg |
| 2 | Almirah Medium steel with shelves (Drawing No : FD-1032)DIMENSION: Overall size shall be 1270 mm high, 765mm wide and 440mm deep. Shelf thickness-0.7mm, Back thickness-0.8mm, Other Componenets thickness-0.9mmDESCRIPTION: The base shall be made of two numbers mild steel sheet channel base welded to bottom of almirah and shall be 100mm high. Mild steel sheet shall be 1mm thick for channel base. The base channel shall be welded at 50mm from each end of 765mm length and shall be up to full width of 440mm of almirah. Top, sides, back, bottom and front of almirah shall be of 1mm thick mild steel sheet. Three shelves equally spaced making four compartments shall be provided and shall be of 1mm thick mild steel sheet.Front shutters shall have two leaves.All joints and welding, fixing shall be done according standard workmanship. Make- GodrejHANDLE: A steel chromium plated handle 100mm long shall be provided to the shutter.LOCKING DEVICE:The locking device shall be three way locking device and shall also be provided with decorative key plate .Make of Lock-Harrison/Godrej.FINISH: All steel surfaces exposed to view when placed in position shall be paintedwith two coats of green hammerpaint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on left top corner of front shutter of visisble colour as directed by Engr-In -Charge.Rest all as per drgs |
| 3 | Book case steel 1675x840x305mm (Drawing No : FD-1028)DIMENSION:Over all size shall be of 840 mm long, 310 mm wide and 1675 mm high.DESCRIPTION:All sheet shall be mild steel sheet 1 mm thick, back, sides, bottom, top and shelves.The book case shall be provided with four compartments of equal size. The shutters of each compartment shall open towards top and slide into the depth of the book case.Transparent glass 4mm thick shall be provided to front shutters.Two steel handles of 100 mm long shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate .Make of lock godrej/harrison/linkFINISH: All steel surfaces internally and externally shall be paintedwith two coats of silver hammer paint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided ontop shutter of visible colour as directed by Engr-in -Charge. |
| 4 | Bath Mat PVC (Drawing No : FD/E6/MAP/07)The Bath Mat PVC shall be made up of 5mm thick PPCP material .The size of the bath mat shall be 400mm Lx300mm Wx250mmH.The bath mat shall have centre leg of dia 25mm.The four legs shall be in arc shape and of size 10mmx100mm.The top of the bath mat shall have 3mmx10mm thick stiffener moulded along with the seat in single piece underneath. The weight of the bath mat shall not be less than 1.3 kgs. Make-AMKO or equivalent |
| 5 | Bin Soiled linen Multipurpose (Drawing No : FD/E-6/MAP/09)The overall size of the bin linen multipurpose is 1200mm long x 450mm wide x 750mm high. The sides, partitions, shelves, drawers of the bin linen shall be made up of 18mm thick prelaminated particle board exterior grade. The back of the bin linen shall be of 12mm thick commercial plywood. The three equal shutters shall be provided with magnetic catchers. All fittings and fixtures shall be done as per drg.The base shall be provided at an height of 75mm from ground and shall be of hardwood sheesham with four nos of 25x25mm stiffeners placed at equidistant positions. Rest all as per drg. |
| 6 | Chair Dining Offr\"s (Drawing No : FD/E6/MAP/04)Overall size shall be 950mm high,450mm wide and 450mm deep.The size of the legs shall be 40x50mm .Front and side rails shall be of size 25x65mm.Stiifeners of size 20mmx25mm three in nos shall be fixed as specified in drg..75x75x25 teak wood stopper shall be fixedwith main frame and legs four nos each in every corner for the support of the cushion and seat ply.75mm thick 40 density cushion of approved foam (Kurlon/sleepwell) covered with approved tapestry cloth shall be fixed over 12mm thick ply as specified in drg.Side frame of back of the chair shall be ofsection 40x50mm..Four teak wood vertical stiffenersof section 20x30mm shall be fixed in back of chair. 25mm dia and 25mm high nylon buffersshall be provided to bottom of all legs.The curved teak wood back shall be of section 30x45mm.All sizes shall be taken as stated in specification, irrespective of what is shown on drg.All wood surfaces shall be lacquer polished with high gloss finish of walnut shade. Rest all as per drg. |
| 7 | Chair Writing (Drawing No : FD/E6/MAP/12) The frame of the chair shall be of MS tubular frame powder coated, cantilever type of size 25mmx10mm in section. Back form shall be designed with contoured lumber support for extra comfort. 120mm thick hot pressed plywood upholstered with superior quality fabric and moulded polyurethane foam with PVC lipping alround shallbe provided at seat and back. PU arms shall be of superior quality and reinforced with MS insert. It shall be scratch and wheather resistant. Steel portion of chair shall be painted with two coats of synthetic enamel paint of black colour over a coat of primer. Rest all specifications areas per drg and directed by Engr-In-Charge |
| 8 | Chair Varandah (Drawing No : FD-259)CHAIRVERANDAH:-All as shown or drawing. The legs on both sides of chair shall be of 20mmm dia mild steel conduit of well thickness as 1.6mm made to shape as shown on drawing. The width at bottom of legs in sides shall be 600mm at at seat portion the width shall be 405mm. The frame of legs shall be joined in front with 10mm dia mild steel rod welded to legs at 75mm below the bottom of front portion of seat. The frame of legs shall be in one piece. The seat and back rest shall be made of one piece. The width of seat between the legs shall be 460mm. The top of back rest shall be 760mm from bottom of legs. The front of seat shall be at 35mm high and back of seat shall be 300mm high from bottom of legs. Two horizontals of 20mm dia mild steel tube of wall thickness as 1.6mm shall be provided one at the rear of seat and other at bottom of back rest over which nylon cane shall be woven as shown on drawing. 3mm thick flat iron plate shall be welded at the bottom of all legs. Caning shall be done with 4mm wide cane in mat pattern or as directed by Engineer-in-charge in the seat, back and hand rest portion. PVC/hard rubber toes shall be provided to the bottom of all legs. All steel surfaces exposed to views when placed in position shall be painted with two coats of enamel paint over a coat of primer after preparation of surfaces as directed by Engineer-in-charge. Painting shall be done with spray machine. Caning shall be done after the painting of chair. |
| 9 | Chair Easy (Drawing No : FD-229/17/201)DIMENSION: Overall size shall be 510 mm long, 575mm wide and740mm high .DESCRIPTION:- All wood shall be first class teak (MP). Front legs shall be 30mmx55mm in section and 350mm high up to seat level. Rear legs shall be of 25mmx55mm in section and 300mm high up to seat level and slanting 50mm away from vertical. Front, back and side rails of seat shall be out of 30mmx55mm in section and made to shape as shown on drawing. front, back and side rails shall join the front and rear legs at 355mm high and 300mm high in rearTeak wood arm rests shall be provided at 150mm above seat level and shall be of 30mmx55mm in section as shown on drawing. Back rest shall be made of frame consisting of top horizontal rail of 30mmx100mm in section out of 60mmx100mm teak wood made to shape as shown ondrawing and lower horizontal rail of back restshall be of 30mmx100mm in section joined together by vertical side rails of 30mmx25mm in section teak wood to form the frame|Caning shall be done with plastic cane of 2mm wide and 0.4mm thick half round gola type weighing not less than 6gms in ten running meters. Caning shall be done in Godrej pattern.PVC shoes 25mmx25mm shall be provided at the bottom of all legs.FINISH:- All wood surfaces exposed to view when placed in position shall be given high gloss French polish with lacquer finish. |
| 10 | Chair CB Steel with Arms (Drawing No : FD-75)DIMENSION:Overall size shall be 535mm wide,560mm deep and 900mm high. DESCRIPTION: Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 20mm dia steel tubing having wall thickness 1.6mm Welding of frame where required shall be as directed by GE/BSO and in running welding grinded to give smooth surface. The seat and back frame of the chair shall be made up of quality sheesham wood in natural polish with polythene cane in godrej pattern confirming to IS-5378:94(Type-I) of durable quality. The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame. The seat and back shall be fixed by providing suitable nut bolts and washers. The arms shall be of PPCP material in lieu of wooden and shall be fixed with screws from beneath.Weaving of cane shall be done with premier or shah brand plastic cane in godrej pattern. Cane shall be 2mm wide and 0.4mm thick, Gola type weighing not less than 6 gms/10 RM. Bottom of legs shall have hard rubber shoes. FINISH: All iron surfaces exposed to direct view shall be painted with two coats of enamel grey paint over a coat of primer after preparation of steel surfaces. Painting shall be done with spray machine to achieve smooth surfaces. |
| 11 | Chair Wooden bottom w/o Arms (Drawing No : FD-25/225/285)DIMENSION:-Overall size shall be 445mm long,440mm wide and 835mm highDESCRIPTION:-.Timber shall be seasoned teak wood Ist Quality. Front legs shall be of size 30mmx55mm in section and 435mm highand rear legs shall be of section30x55mm and 815mm high. The legsshall be joined by front, sides, rear rails made to shape out of 30mmx65mm in section. Two side stiffeners in short rails shall be provided of 20mmx25mm in section.One stiffener of 20mmx25mm shall also be provided at centre of both sise stiffeners joining the sides stiffenres. 12MM thick decorative plywood with perforated holes 5MM dia at centre in a radius of 5 inch shall be fixed over the frame of the chair irrespective of what is shown on drg.All Diamensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg.FINISH:-All wooden expose surfaces shall be french polishedtwo coats after preparation of surfaces. |
| 12 | Chair Writingcushion (MB) (TP)DIMENSION:-Back: 39.0cm X 47.0cm, Seat 45.0cm(W) X 42.0cm(D) Overall Dimension of Chair Seat Height Seat Height- Min 43.0 to max 54.0cm. Height-min 86.1 to Max 97.1cm . Width & Depth of chair as measured from Pedestral - Width-71.0cm and Depth- 71.0cm DESCRIPTION:- SEAT/BACK ASSEMBLY: The seat and back should bemade from 1.2 ± 0.1 cm.. thk. hot pressed plywoodmethod described in.and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should bedesigned with contoured lumbar support for extra comfort.SEAT SIZE: 45.0cm(W) x 42.0cm.(D).BACK SIZE: 39.0cm(W) x 47.0cm.(H).SEAT /BACK COVERS: The seat and back covers should beinjection moulded in black Co-polymer PolypropyleneHIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam should bemoulded with density = 4+/-21kg/m and hardness load 16_± 2 kgffor 25%_compression. |
| 13 | ARMREST ASSEMBLY (FOR 7046R): The one-piece armrests should beinjection moulded from black Nylon. The armrests should befitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should bedesigned with the following features• 360° revolving type.• 14° ±2°maximum-back-tilt-only.• Upright position locking.• Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cmTELESCOPIC BELLOW ASSEMBLY: The bellow should be.3 piece telescopic type and injection moulded in black Polypropylene PEDESTAL ASSEMBLY: The pedestal should beinjection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal should be62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). TWIN WHEEL CASTORS: The twin wheel castors should beinjection moulded in Black Nylon. Make- Godrej |
| 14 | Visitor Chair (TP)DIMENSION:-SEAT SIZE : 50.0cm. (W) x 48.0 cm.(D), BACK SIZE : 53.0 cm. (W) x 39.0cm.(H) DESCRIPTION:-1. SEAT / BACK ASSEMBLY : The Seat is injection moulded in glass filled Polypropylene compound which is upholstered with fabric upholstery covers and moulded Polyurethane foam.The Back is injection moulded in glass filled Polypropylene compound which is upholstered with Mesh fabric (Refer colour chart for seat & Back upholestry in product catalog).* SEAT SIZE : 50.0cm. (W) x 48.0 cm. (D)* BACK SIZE : 53.0 cm. (W) x 39.0cm. (H)2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression.3. M.S. POWDER COATED FRAMES FOR 4 LEG CHAIRS :The powder coated (DFT 50±10 microns) welded tubular main frame is made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm and Ø1.6±0.3mm x 0.16 ± 0.0128cm M.S. E.R.W tube. The Ø1.9 ±0.3mm x 0.12 ±0.0096 cmM.S.E.R.W. tube used as connecting member between LH & RH frames.Desklet support frame is made from Ø 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and welded to main frame. |
| 15 | 4. M.S. POWDER COATED FRAMES FOR SLED BASE CHAIRS :The powder coated ( DFT 50±10 microns) welded tubular main frame is made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm and Ø1.9 ±0.3mm x 0.12 ±0.0096 cm M.S.E.R.W. tube.5. SHOE : The shoes are made of glass filled Polypropylene compound with and pressed fitted with tubular frame. Felt is provided below the shoes.6. ARMREST : The Armrest are made of glass filled Polypropylene compound and assembled over the tubular frame.7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Poly Amide.Make:- Godrej |
| 16 | Executive Chair Revolving Tilting (TP)DIMENSION:-SEAT SIZE: 51.8cm (W) x 49.7cm (D), BACK SIZE: 47.9 cm(W) x 66.9 cm (H) DESCRPTION:-SEAT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam.SEAT SIZE: 51.8cm (W) x 49.7cm (D)BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm.BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m³ and hardness 14 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.0±0.1cm height.It also has swivel and To and Fro adjustment with moulded PU armtop.ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: |
| 17 | · 360° revolving type· Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort.· Tilt tension adjustment can be operated in seating position.· 5 position Tilt limiter giving option of variable tilt angle to the chair.· Seat / back tilting ratio of 1:2.· The mechanism housing is made up of HPDC Aluminium & black powder coated(DFT 40 to 60 micron).HEADREST: The Headrest sub-assembly is made up of injection moulded glass filled Polypropylene which is upholstered with moulded HR polyurethane foam and fabric. It has an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair.The complete headrest assembly is retro fit to the main chair. Make:- Godrej |
| 18 | Hand Stand with mirror (Drawing No : FD-361/362)Overall size shall be 1000mm long and 710mm high. All wood shall be of teak wood (mp). Top and bottom horizontal rails and two vertical sides shall form the frame of 50mmx20mm in section for the Hat stand. The top and bottom horizontal rails shall be joined by intermediate vertical stiffeners of 50mmx20mm in section at 288mm from inside of right hand side of vertical frame. On the left hand side of Hat Stand, two horizontal stiffeners, 50mmx20mm in section shall be provided. The top stiffener shall be at 160mm from bottom of top horizontal frame to the center of the top stffener. The bottom stiffener shall beat 200mm from bottom of horizontal frameto the center ofbottom stiffener. On right hand side of Hat Stand. one horizontal stiffener. 50mmx20mm in section shall be provide. The Frame of Hat Stand shall be provided with 4mm thick teak ply (one side teak face). The back of Hat Stand shall provided with 4mm thick commercial plywood. A mirror of 440mm high and 300mm wide with 5.5mm thickness of Atul, Modiguard or Golden fish, free from all distorition and defects shall be provided on right hand side of Hat Stand with 10mmx12mm in section teak wood beads al-around the mirrorl Teak ply 4mm thick shall not be provided at placescoveed by 5.5mm thick mirror irrespective of what is shown on drawing, four brass pegs of 75mm wide and 120mm high of shape as approved by Engineer-in-charge. 35mm wide and 6mm thick teak wood edging shall be provided al-round the Hat Stand. Two key plates of mild steel sheet 3mm thick flat iron with key holes as shown on drawing shall be provided to two top corners at the back of Hat Stand as directed by Engineer-in-charge. All wood and teak ply surfaces exposed to view when placed in positionshall be French polished with high gloss fininsh. All steel surfaces shall be painted with two coats of black paint over a coat of primer after preparation of surfaces Brass pegs shall have shining surfaces and remain untreated irrespective of what is shown on drawing. |
| 19 | Locker bed side (Drawing No : FD-1029)DIMENSION: Overall size shall be 760mm long, 600mm wide and 1100mm high.DESCRIPTION: The locker shall be made of mild steel sheet 1mm thick 20 mm dia conduit pipe shall be chrome plated with wall thickness of 1.6 mm shall be fixed with sidesockets. Two handles chromium plated 100mm long shall be fixed to shutters with necessary riveting. One hasp and staple 75mm long shall also be fixed to shutters with riveting.The left shutters shall be provided with 100mm long tower bolt inside at upper and lower ends also.The locker shall be provided with compartments as shown in drgs made of 1mm MS sheet.FINISH: All steel surface internally and externally, exposed to view when placed in position shall be given two coats of green hammer paint internally and externally after properly smoothened the surface with sand paper and applying putty.A Mark of MES shall also be provided at top left corner of front shutter of visible colour. Painting shall be done with spray machine. Rest all specifications areas per drg . |
| 20 | Peg Table (Drawing No : FD-384)DIMENSION; Overall size shall be 450mm long,300mm wide and 380mm high.DESCRIPTION: Legs shall be of teak wood of section 30mmx50mm.The legs shall be 362mm high.5mmx5mm in section groove shall be provided on the top of legs which shall be visible when placed in position. Two nos top rails of section 20mmx40mm of teak wood shall be provided connecting legs. Two bottom rails of size 20mmx40mm shall be fixed betweenthe legs. A centre stiffeners of size 20x40mm shall be provided at centre of side bottom rails for extra support irrespective of what is shown on drg.Top of the table shall be of 18mm thick pre-laminated MDF board with 4mm teak wood edging all round the top oftable.FINISH: All wood surfaces exposed to view when placed in position shall be french polished with high lacquer finish.Rest all as per drg. |
| 21 | Receptable PVC (Drawing No : FD/E-6/MAP/13) The body of receptacle PVC shall be made up of thick polymer plastic. It shall be of capacity 20 liters,providedwith lid and handle as shown in drg. |
| 22 | Side Board (Drawing No : FD-241/372)DIMENSION:Overall size shall be 1500mm long, 450mm wide and 760mm high.DESCRIPTION: All wood shall be first class hard wood teak .The bottom frame shall be of 18mm thick teak wood frame and shall be 125mm high from ground.All sides i.e-front shutters, top, bottom sides and front sides of drawers shall be of 18mm thick prelaminated MDF board. Four drawers shall be provided in the right hand side of the side board. Left hand side shall have one hung shutters. Back of side board shall be of 12mm thick commercial ply irrespective of what is shown on drg. Bottom of drawers shall be of 6 mm thick plywood commercial. The shutters shall have continuous piano type hinges. The top of one shutter shall have 50mm long flush bolt fitted towards inside of shutter. Two knobs shall be provided to the shutter. Four knobs shall be provided to the four drawers (one for each drawer) 3mm x 19mm teak wood edging shall be provided to all edges of particle board and shelf. FINISH:All wood and particle board surfaces exposed to view when placed in position shall be French polished with high gloss finish. Rest all as per drg. |
| 23 | Table 3\"x2\" 900 Widthx 590 Depthx 750 Height (TP)DIMENSION:-Overall size shall be 900 Widthx 590 Depthx 750 Height ..DESCRIPTION:-Table - T 31 size shall be900 Widthx 590 Depthx 750 Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall besq. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mmthick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA MS . Also there should be 10 lever cam lock plus handles built in plastic. Make- Godrej |
| 24 | Table Steel (900x900x760mm) (Drawing No :FD-1009)Table 3x3:- Overall size shall be 900mm,900mlong,760mm wide and 760mm high. Steel frame shall be of 800 mm 800mm 742mm . Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm. Legs shall be joined together with the top rails of 25mm square mild steel tube of thickness 1.6mm. Top of the table shall be of 18mm thick pre-laminated paticle board of teak veneer shade and provided with PVC edging all round the table. Hard rubber/PVC toes shall be provided to bottom of legs. All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces. |
| 25 | Table office clerk steel (Drawing No :FD-1004)TABLE OFFICE CLERK STEEL,FD-1004Overall size shall be 1200mm long, 610mm wide and 760mm high. Steel frame shall be of size 1160x570x742mm four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. Two short stiffeners f same size shall be provided at 130mm from bottom of legs. One long stiffener shall also be provided to the middle of short stiffeners. Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep. The top of table shall be provided with pre-laminated particle board of 18/19mm thick with teak veener shade and PVC edging alround the table. Hard rubber/PVC toes shall be provided to the legs. Locking device shall be provided to drawers. All steel surfaces exposed to view shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces. Rest all as per drgs. |
| 26 | Table centre (FD-274)DIMENSION:Overall size shall be 900mm long, 450mm wide and 400mm high.DESCRIPTION: All wood shall be of teak wood. Top of the table shall be of 18mm thick prelaminated MDF board of approved shade with 4mm thick teak wood beading all-round the edges of top.Legs shall be made out of 60mmx30mm in section teak wood and 356 mm high. Bottom rail of teak wood of 20mmx50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs.The bottom tier shall be fixed on the top of bottom side rails with 50mm long screwss.The bottom tier shall be of 18mm thick prelaminated particle board exterior grade of approved shade with 4mm thick teak wood beading all-round the edges of both the tops.25mm dia hard rubber /PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws.FINISH:All wood surfaces shall be French polished with high gloss finish Rest all as per drg. |
| 27 | Table Bed Side (FD/E6/MAP/15(R))The overall size of the table bed side shall be 450mm x 450mm x 600mm from rear and 450mm x 450mm x 500mm from front as shown in drg.The entire frame of table bed side shall be made up of 18mm MS square pipe (18 Gauge) duly black powder coated. The two sides and top shall be made up of 18mm thick prelamainted particle board exterior grade. The Back of the table except the top portion as shown in drg shall be provided with 6mm commercial plywood BWR grade duly screwed to frame. The two sides, back and bottom of drawers of the table shall be made up of 12mm thick commercial plywood irrespective of what is shown on drg, except the front side which shall be of 18mm thick prelaminated particle board exterior grade. The drawers shall be made functional on teak wood runners fixed inside the tables shown on drg.The drawers of the tables shall be provided with 100mm long CP handles .Rest all as per drg. |
| 28 | Table Dressing Ladies (Drawing No : FD/MAPII/07)The overall size of the table dressing shall be 1150mm long 380mm wide and 1700mm high. The sides, top ,back and frontof the base unit shall be of 18mm thick prelaminated MDF board. The bottom of the side units shall be of 12mm thick commercial plywood. The sidesand back drawers shall be of 12mm thick prelaminated MDF, bottom of the drawers shall be of 6mm thick commercial ply whereas the front of the drawers shall be of 18mm thick prelaminated MDF board.5mm thick electro copper plated mirror shall be fixed over 6mm thick plywood back. The plywood shall be fixed on two vertical hardwood member of size 45mmx35mm .a horizontal support of size 30mmx20mm shall be provided in between two vertical members. The Overall size of the stool shall be 440mm long 350mm wide and 425mm high. The four sides shall be of 18mm thick prelaminated MDF .The top of the stool shall be of 12mm thick plywood openable as shown in drg.Four heavy duty revolving nylon double wheels shall be provided at base below the 6mm base ply fixed over wooden runner 20mmx20mm.The seat of the stool shall be 75mm high, made of foam 40 density covered with tapestry cloth as approved by Engr-In-charge/GE. Rest all as per drg. |
| 29 | Table Dressing with mirror Gents (Drawing No : FD-379/230)DIMENSION:Overallsize shall be 900mm long, 300mm wide and 150mm high at bottom with support of mirror as 1115mm high.DESCRIPTION: The frame of mirror shall be overallsize of 410mm wide and 790mm high, fixed at 150mm from top of lower base.The entire box shall be made of 12mm thick prelaminated MDF board except back and bottom which shall be of12mm thick plywood .The sides of the drawers shall be made of 12mm thick commercial ply with bottom of 6 mm ply and front of 12mm thick prelaminated MDF board.The mirrorof 380mmx760mm shall be providedwith its wooden frame made of 25mmx35mm teak wood battens.The bach shall be of 6mm thick plywood.5.5mm thick mirror distortion free shall be provided on 6mm thick plywood backing..3mm thick flat iron key plates of MS.Two knobs of aluminium anodized dark brown in shade shall be provided to both the drawers. 25mmx25mm in section shall be provided at top of mirror and painted with black paint.FINISH:All wood surfaces shall be french polished with high gloss finish. |
| 30 | Teapoy wooden (Drawing No : FD-382/278)DIMENSION: The overall size shall be 600mm long, 450mm wide and 540mm high.DESCRIPTION:The legs shall be 60mmx30mm in section and 497 mm high and shall be of teak wood. 5mm x 5mm in section groove shall be provided at the visible portion of top of legs. Top rails of teak wood of 20mmx50mm in section and 510mm long shall be provided between the legs. Bottom rail of teak wood of 20mm x 50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs.A centre rail of size 20mm x 50mm shall also be provided lengthwise at centre in between the side bottom rails irrespective of what is shown on drg. 25mm thick and 25mm dia hard rubber /PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws. Top of the table shall be of 18mm thick prelaminated MDF board exterior grade of approved shade with 4mm thick teak wood beading all-round the edges of top.FINISH: All wood surfaces shall be French polished with high gloss finish. Rest all as per drg |
| 31 | Table Writing (Drawing No :FD-275)DIMENSION:Overall size shall be 1145mm long, 600mm wide and 760mm high.DESCRIPTION: All wood shall be of first class hard teak wood except top and right hand side drawer cabinet. Legs shall be of 35mmx55mm in section and 717mm high having 5mmx5mm in section groove at the top of legs at the portion when placed in position. The top shall be of 18mm thick prelaminated MDF board of approved shade and the edges shall be covered with 4mm thick teak wood beading. Two short stiffeners of teak wood of size 50mmx40mm in section irrespective of what is shown on drg shall be provided between legs at 100mm from bottom of legs. Sides of the box whichhouse the drawer and cabinet shall be 18mm thick prelaminated particle board exterior grade. Sides and back of drawers shall be of 12mm thick teak wood planks. Bottom of drawers shall be of 6 mm thick plywood commercial.6mm thick plywood commercial 75mm high partition shall be provided in the drawer. Shutter for cabinet shall be fixed with piano type continuous hinges. Lock shall be provided to drawer and shutters. Recessed handle shall be provided to drawer and shutter.25mm dia and 25mm high rubber shoes shall be fixed to bottom of legs.FINISH: All wood surfaces shall be French polished with high gloss finish. Rest all as per drg. |
| 32 | Chair CBA Steel (Drawing No : FD 120/125(M))DIMENSION:Overall size shall be 535mm wide,560mm deep and 900mm high.DESCRIPTION:Seat shall be 455mm high from floor. Conduit pipe used for frame shall be 25mm dia mild steel tubing having wall thickness 1.6mm Welding of frame where required shall be as directed by GE and in running welding grinded to give smooth surface.The seat and back frame of the chair shall be made up of quality teak wood in natural polish with polythene cane in godrej pattern confirming to IS-5378:94(Type-I) of durable quality .The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame.The seat and back shall be fixed by providing suitable nut bolts and washers..The arms shall be of PPCP material in lieu of teak wood and shall be fixed with screws from beneath.Weaving in teak wood seat and back shall be done with plastic cane in godrej pattern. Cane shall be 2mm wide and 0.4mm thick, Gola type weighing not less than 6 gms/10 RM..Bottom of legs shall have hard rubber shoes. FINISH: All iron surfaces exposed to direct view shall be stove enamelled painted with two coats of enamel grey paint over a coat of primer after preparation of steel surfaces. Painting shall be done with spray machine to achieve smooth surfaces. |
| 33 | Charpoy IP Hard Top (Drawing No : FD/E6/MAP II/ 01)Overall size shall be 1980mm long, 900mm wide and 440mm high.Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mm x 25mm x 16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer.Rest all as per drg |
| 34 | Form with Back (Drawing No : FD 32/78)DIMENSION:Over all size shall be of 1800X510X900MM.DESCRIPTION:wooden seat shall be of teak wood in one piece and of size 1800mm long 255mm wide and 25 mm thick bolted to frame with 3 mm dia GI nut bolt and washers.Steel frame shall be 1500mm long in such a way that teak wood seat shall project 150mm from frame on each side. Back rest shall be of teak wood and 1800mm long,150mm wide and 19mm thick. The back rest shall be 1800mm long the width is 300mm at bottom and 255 mm at top of wooden plank. Legs shall be 25mm MS tube of wall thickness 1.6mm.Steel frame shall be provided with 25mm square MS tube 16 gauge .All Dimensions, shape and size shall be followed as per drg.FINISH: All wooden expose surfaces shall be french polishedtwo coats after preparation of surfaces and steel portion shall be painted with synthetic enamel black paint |
| 35 | Rack Rifles (Drawing No : CM/FUR-9)Wooden Rifle Racks to secure 04 nos of 5.56 INSAS Rifles, without Amm. Box, Single Tire Type. Overall Spec (in Inches) - L:24\" X W:15\" x H: 36\". FINISH:- All wood surfaces shall be French polished with high gloss finish. |
| 36 | Receptable (Drawing No :FD/E6/MAP/ 13)The body of receptacle PVC shall be made up of thick polymer plastic. It shall be of capacity 20 liters,providedwith lid and handle as shown in drg. |
| 37 | Table 900X600XMM W/O Drawer (Drawing No :FD-1007)DIMENSION:-Overall size shall be 900mmX600X760mm.DESCRIPTION:-Steel frame shall be of 800mmX500mmX742mm.Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm.Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm top rails on long and short sides.Two short stiffeners joining legs in short sides of 100mm from bottom shall be provided in the middle of short stiffener joining short stiffeners with 25mm square mild steel tube of wall thickness 1.6mm at 100mm from bottom of legs.The top shall be of prelaminated MDF board of 18/19mm thick with teak wood edges alround the edges of the top fixed with headless nails and adhesive. PVC/hard rubber toes shall be provided to the bottom of legs.FINISH:-All steel surfaces exposed to view when placed in position shall be painted with two coats of granular silver grey enamel paint over a coat of primer with spray machine after preparation of steel surfaces. |
| 38 | Almirah Steel Medium (Drawing No :FD-1032)DIMENSION: Overall size shall be 1270mm high,765mm wide and 440mm deep.DESCRIPTION: The base shall be made of two numbers mild steel sheet channel base welded to bottom of almirah and shall be 100mm high. Mild steel sheet shall be 1mm thick for channel base. The base channel shall be welded at 50mm from each end of 765mm length and shall be up to full width of 440mm of almirah. Top, sides, back, bottom and front of almirah shall be of 1mm thick mild steel sheet. Three shelves equally spaced making four compartments shall be provided and shall be of 1mm thick mild steel sheet.Front shutters shall have two leaves.All joints and welding, fixing shall be done according standard workmanshipHANDLE: A steel chromium plated handle 100mm long shall be provided to the shutter.LOCKING DEVICE:The locking device shall be three way locking device and shall also be provided with decorative key plate. Make of Lock-Harrison/Godrej.FINISH: All steel surfaces exposed to view when placed in position shall be paintedwith two coats of green hammerpaint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on left top corner of front shutter of visisble colour as directed by Engr-In -Charge. Rest all as per drgs |
| 39 | LOCKER (DRAWING NO : FD-1029)DIMENSION: Overall size shall be 760mm long, 600mm wide and 1100mm high.DESCRIPTION: The locker shall be made of mild steel sheet 1mm thick.20 mm dia conduit pipe shall be chrome plated with wall thickness of 1.6 mm shall be fixed with sidesockets.Two handles chromium plated 100mm long shall be fixed to shutters with necessary riveting . One hasp and staple 75mm long shall also be fixed to shutters with riveting.The left shutters shall be provided with 100mm long tower bolt inside at upper and lower ends also.The locker shall be provided with compartments as shown in drgs made of 1mm MS sheet.FINISH: All steel surface internally and externally, exposed to view when placed in position shall be given two coats of green hammer paint internally and externally after properly smoothened the surface with sand paper and applying putty. A Mark of MES shall also be provided at top left corner of front shutter of visible colour. Painting shall be done with spray machine. Rest all specifications areas per drg. |
| 40 | BATH MAT (DRAWING NO : FD/E6/MAP/07)The Bath Mat PVC shall be made up of 5mm thick PPCP material .The size of the bath mat shall be 400mm Lx300mm Wx250mmH.The bath mat shall have centre leg of dia 25mm.The four legs shall be in arc shape and of size 10mmx100mm.The top of the bath mat shall have 3mmx10mm thick stiffener moulded along with the seat in single piece underneath. The weight of the bath mat shall not be less than 1.3 kgs. |
| 41 | CHAIR WRITINGH (DRAWING NO : FD/E6/MAP/12)The frame of the chair shall be of MS tubular frame powder coated ,cantilever type of size 25mmx10mm in section. Back form shall be designed with contoured lumber support for extra comfort.120mm thick hot pressed plywood upholstered with superior quality fabric and moulded polyurethane foam with PVC lipping alround shallbe provided at seat and back. PU arms shall be of superior quality and reinforced with MS insert.It shall be scratch and wheather resistant. Steel portion of chair shall be painted with two coats of synthetic enamel paint of black colour over a coat of primer.Rest all specifications areas per drg and directed by Engr-In-Charge |
| 42 | CHARPOY IP HARD TOP (DRAWING NO-FD/E6/MAP11/01)Overall size shall be 1980mm long, 900mm wide and 440mm high.Two long rails and two short rails shall be of 25mm x 65mm x 16 gauge MS rectangular pipe .The legs shall be of size 32mm x 32mm x 16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mm x 25mm x 16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mm x 60mm x 6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mm x 25mm x 16 gauge shall be provided at 150mm from ground level. 12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg. PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer.Rest all as per drg. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
