|
| 1 | 25 mm thick, cement concrete type D-2, 1:4:8 using 12.5 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified. |
| 2 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified. |
| 3 | Factory made 35 mm thick ,2nd class hard woodGlazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);,etc complete all all as specified. |
| 4 | Factory made, 35 mm thick, second class hard wood, plain framed, hammer marked, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete, all as specified. |
| 5 | Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, thickness 25 mm,etc complete all as specified. |
| 6 | Plywood 19 mm thick , grade BWR, type BB, fixed with screws to timber frame work etc. built in cupboard complete all as specified and directed. |
| 7 | 18/19 mm thick PVC board Rajshree Celuka ply or equivalent as approved of grade 1 quality with both side plain white or coloured fixed with stainless steel screws , solvent cement/adhesive to fabricate kitchen cabinet sides, top and bottom, door shelf inside the cabinet and drawer and all fittings complete all as per manufacturer\"s instructions and as directed by Engg-in-Charge.NOTE :- (i) Each member i.e. top and bottom, door, shelf inside the cabinet and drawer etc. shall be measured.(ii) Hinges, wire gauge and handles shall be measured and paid for separately. |
| 8 | Factory made solid PVC moulded door shutter, 28-30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2 mm thick plain colur PVC sheet on back face, as shown on page 181 of MES Schedule Part-II, completeall as specified. |
| 9 | Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforcedwith mild steel square tube, suppling & fixing in opening, complete all as specified. |
| 10 | Aluminium anodised barrel tower bolt of extruded section 100 mm long, ISI marked, complete all as specified. |
| 11 | Aluminium anodised barrel tower bolt of extruded section 200 mm long, ISI marked, complete all as specified. |
| 12 | Stailess steel, handle, 100 mm long, curve shape with stainless steel screws, complete all as specified. |
| 13 | Auto closing stainless steel (Grade 304) hinges 35 mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters of make as approved complete all as specified. |
| 14 | Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extrudedsections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300 mm long,complete all as specified. |
| 15 | Stainless steel 75mm long butt hinges with stainless steel screws, ISI marked complete all as specified. |
| 16 | Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified. |
| 17 | Extruded aluminium anodised handles fabricated type with plate 100 mm long, ISI marked complete all as specified. |
| 18 | Extruded aluminium anodised handles fabricated type with plate 150 mm long, ISI marked, complete all as specified. |
| 19 | Aluminium (Die cast) door closer hydraulically regulated designation No. 2 aluminium body universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg, ISI marked,IN REPLACEMENT complete all as specified. |
| 20 | Mild steel ordinary rat tail rod pattern helical door spring 300 mm long including roller and roller plate, complete all as specified |
| 21 | Floor door stopper of aluminium alloy body and tongue , anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140mm ,complete all as specified. |
| 22 | Soft rubber beading, 50 to 65 mm wide, 5mm thickfixed in repairs the bottom of door shutters with screws, nails, adhesive and covered with 4mm thick teak wood beading of 20mm wideall as specified. |
| 23 | Hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws of size 100 mm, ISI marked IN REPLACEMENT, complete all as specified. |
| 24 | Stainless steel conduit 25 mm bore, cut to size and erected in position as curtain rod on backets, with & including SS decorative finials & brackets, PVC rings @ 10 nos. per metre, fixed to walls with PVC rawl plugs & SS screws,IN REPLACEMENT,all as specified |
| 25 | Factory made pre painted pressed steel frames, conforming to IS,having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, all as specified. |
| 26 | Factory made pre painted pressed steel frames, conforming to IS,having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete, all as specified |
| 27 | Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples,all as specified. |
| 28 | Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples IN REPLACEMENT, all as specified. |
| 29 | Powder coatedaluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 30 | Powder coated aluminium door shutters with styles & rails, anodised alumnium glazing snap beading, rubber neoprene packing including joining cleats &screws etc as per manufacturers instructions, complete all as specified. NOTES: (a) Each shutter shall have2 Nos. 200 mm long almn handles and 03 No. 100 mm size stainless steel/almn butt hinges.(b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ.(c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron. |
| 31 | Powder coated aluminium window and ventilator shutters side hung typewith aluminum section weighing 0.55 Kg/m, anodised alumnium glazing snap beadingrubber neoprene packing including joining cleats &screws etc as per manufacturers instructions, complete all as specified.NOTES: -(a) Each shutter shall have2 Nos. 125 mm long almn handles and 02 No. 75 mm size stainless steel/almn butt hinges & one no. almn hook & eye.(b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ.(c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron. |
| 32 | Granite jet black shade, 15 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished,bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified. |
| 33 | Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified. |
| 34 | Glazed ceramic coloured tiles 7-8 mm thick,area of each tile exc. 0.13 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified |
| 35 | Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 Sq.m but n. exc. 0.11 Sq.m,laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 36 | Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m,laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 37 | Vitrified ceramic, double chargedstraight cut/joint free, 9-10 mm thick dark shade tiles, area of each tile not exceeding 0.38 Sq.m, on vertical surfaces such as skirting, dado etc over & including 10 mm thick cement mortar (1:4) screed set and jointed with grey cement slurry & pointed with polymer based grout of matching shade, complete, all as specified. |
| 38 | Rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fairon walls in cement mortar (1:6),complete all as specified. |
| 39 | Rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified.NOTE: WPC will be measured and paid for separately under respective item of BoQ |
| 40 | Supply only water proofing compound, ISI marked, complete all as specified. |
| 41 | Two coats of interior acrylic distemperover and including a coat of acrylic emulsion primer. on new plastered wall surfaces, including preparation ofsurfaces, complete all as specified. |
| 42 | Two coats of cement base paint on new wall surfaces including preparation of surfaces complete all as specified. |
| 43 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surroundings; glazing with putty or fixed with beads complete all as specified |
| 44 | Sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden / Aluminium beads in squares n. exc. 0.5sqm in each pane complete all as specified. |
| 45 | Figured glass 4 mm thick ordinary quality and glazing with oil putty or wooden / Aluminium beads in squares n. exc. 0.5sqm in each pane complete all as specified. |
| 46 | Plain sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5 Sq.min each pane complete all as specified. |
| 47 | Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified.complete all as specified. |
| 48 | Two coatsof synthetic enamel paint over & including a coat of pink primer overnewwood and wood basedsurfaces of any description not other wise described over 10cm width or girth, including preparation of surfaces complete all as specified. |
| 49 | Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, including taking up or down steel tubing and connections from existing location, complete all as specified of size: - |
| 50 | 15 mm bore . |
| 51 | 20 mm bore . |
| 52 | 20 mm bore balllPTMT valve , high pressure with polythene float and flynut complete screwed for iron pipe or brass,IN REPLACEMENT, all as specified and directed. |
| 53 | PVC water storage tank (500/1000 ltr) cover with fitting, IN REPAIRS, complete all as specified. |
| 54 | Nipple 20 mm bore suitable for HDPE water tank (minimum weight 45 gm ), complete all as specified. |
| 55 | Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. |
| 56 | Chromium plated fancy type stop valve/cock, cast copper alloy, chromium plated, with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. |
| 57 | Concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. |
| 58 | Stainless Steel kitchen plate rack of sheet thickness not less than 0.61 mm overall size 610 x 760 x 254 mm, fixed on walls wth PVC plugs and SS screws, INREPAIRS, complete.MAKE: PRAYAG Cat No. PSP-2 or equivalent make mentioned in Appndix \"B\". |
| 59 | Taking down old MS window shutter n exc 1 sqm each including cutting old hinges and refixing in same opening after necessary repair/welding work and changing MS hinges of any type including welding to old framecomplete all as specified and as directed. |
| 60 | Demolition and Dismantling work |
| 61 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified. |
| 62 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified. |
| 63 | Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and removing from site all as specified. |
| 64 | Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in same opening after reseuring or easing & ajustting etc complete all as specified and directed. |
| 65 | Taking down shutters of any description not exceeding 1.00 sqm each and and removing from site all as specified. |
| 66 | Taking down cement plaster of any description on brick walls or concrete surfaces etcincluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified. |
| 67 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified. |
| 68 | Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) all as specified |
| 69 | Note : Amount ofcredit for retrieved materials is mentionedin Sch of credit of tender documents in pdf form which will be deducted while acceptance of tender offline. |
