|
| 1 | Dismantling of plain or corrugated steel sheeting any gauge, thicknes, including Naintak or similar pattern roof coverings of any description etc complete all as specified and directed. |
| 2 | Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified and directed. |
| 3 | Dismantlingfloor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed. |
| 4 | Dismantling unframed timber scantling 40 sqm and over in section, in any position complete all as specified and directed. |
| 5 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 6 | Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed. |
| 7 | Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters (Without taking off shutters from the frames complete all as specified and directed. |
| 8 | Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed. |
| 9 | Demolition of reinforced cement concrete in roof, floor (other than ground floor), beams, stairs, landing, chajjas and simmilar work n.exc 15 cm thickcomplete all as specified and directed. |
| 10 | M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in slabs suported on wall, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like such as cover slab of septic tank/soak well etc complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately). |
| 11 | M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete (Horizontal or sloping) complete all as specifed and directed. |
| 12 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hookingends and binding with mild steel wire (annealed) n.less than 0.9mm dia complete all as specified and directed. |
| 13 | M & L for mild steel TMT bars 6 to 8mm dia, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends as in stirrups, spacers, binders etc and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. |
| 14 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified complete all as specified and directed |
| 15 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specifiedincl dismentalling existing sheetcomplete all as specified and directed |
| 16 | S & F 4 mm thick of size 600x600mmHSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer boardE-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mmduly suspended with 2mm dia SS bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed. |
| 17 | M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate in sub base to receive floor finishes complete all as specified and directed. |
| 18 | S&F light shade vitrified ceramic tiles 8 to 10mm thick area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, each in floors laid over and including 15mm thick screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed. |
| 19 | All as per Item No.18 above but on vertical surfaces such as skirting , dado risers to stepsfixed over and including 10 mm thick bedding layer in CM 1:4,set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 20 | S&F Non skid ceramic colour floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqmin floors laid over and including 15mm thick screed bed or bedding layer in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed. |
| 21 | M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. |
| 22 | M&L 18-20mm thick granite work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layerin cement mortar 1:6etc complete all as specified and directed. |
| 23 | S&F for Steel work in tubular trusses, post, purlin including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st 240 complete all as specified and directed. |
| 24 | M&L for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, pipe, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E 250) quality-A complete all as specified and directed. |
| 25 | S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n exc 15cm long - 11 to 15mm Diameter of neck complete all as specified and and directed. |
| 26 | S & F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixing in opening as per specification & drawing complete all as specified & directed. |
| 27 | S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified & directed. |
| 28 | S&F powder coated (minimum thickness pf power coating 50 micron) anodised aluminium frame for door, window, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 29 | S&F powder coated (thickness power coating not less than 50 micron) anodised aluminium door shutters aluminium section weighing 0.55kg/m including necesarry joining cleats glazing clips rubber neoprene packing,handle 2 Nos in each door anodised aluminum snap beading screw and mortice lock vertical type Brass 2 levers, size 100 mm etccomplete all as specified and directed. |
| 30 | S&F powder coated (thickness power coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type withoursash bar aluminium section weighing 0.55kg/m including necesarry joining cleats glazing clips rubber neoprene packing, anodised aluminum snap beading screwlock etc complete all as specified and directed. |
| 31 | S&F Sheet glass 4.8mm thick clear/sun shade colour glass, ordinary quality and glazing with oil putty in squares exceeding 0.5sqm in each pane complete all as specified and directed. |
| 32 | S& F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed. |
| 33 | M&L for 4 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats complete all necessary items to fix with frame and all as specified and directed. |
| 34 | S & F pressed steel frames 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plateincluding one shop coat of primer complete all as spd and directed |
| 35 | S & F pressed steel frames 125 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plateincluding one shop coat of primer complete all as spd and directed |
| 36 | M & L for PCC 1:3:6 type C-0, using 12.5 mm graded crushed stone aggregate as in back filling ofhollow portion of frame with and for fixing of hold fast complete all as specified and directed. |
| 37 | S&F IInd class hard wood, 35mm thick skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc,size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts complete all as specified and directed. |
| 38 | S&F IInd hardwood 40mm plain framed pannelled shutter (any number of pannels) with panels of timber flats on bothe sides (feather edged) or of veneered particle board medium densitywood particle board with commerical face veneers and fitted to chowkats complete all as specified & directed. |
| 39 | S&F 100mm size Stainless steel butt hinges complete all as specifed and directed |
| 40 | S&F Stainless steel barrel tower bolt 200mm long of extruded section complete all as specified & directed. |
| 41 | S&F Stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed Length of bolt 250 mm complete all as specified & directed. |
| 42 | S & F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed |
| 43 | S&F for aluminium (extruded section) bodydoor closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 44 | M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed. |
| 45 | M&L for preparation of previously treadted surfaces old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paintall as specified. |
| 46 | Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed. |
| 47 | Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed. |
| 48 | S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 49 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 50 | S&F in repairs one piece EWC with soft close seat cover and twin flush fittings 660 x 365 x 765 mm (snow white) S trap/P trap 300mm and fittings complete all as directed and approved. |
| 51 | S&F in repair viterous China squatting pan, `Orrisa\" pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed. |
| 52 | S&F in repair of PVC low level flushing cistern dual flush top push,10 Ltr capacity symphonic action type white as approved, ball valve float valve and handle, flush pipe incl CP bracket complete all as specified & directed. |
| 53 | S & F in repairs Vitreous China half stall Urinal or bowl type pattern, basin only including connections to flushing pipe, urinal spreader, waste pipe and outgoing pipes fixed in repairs (excluding flushing cistern)complete all as specfied and as directed. |
| 54 | S&Fin repairs Viterous China wash basin with full/half Pedestal, white, flat back, size 550x400mmexcluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specfied and as directed. |
| 55 | S&Fin repair 15mm dia 600 mm long PVC connection including brass check nut at both endsscrewed both endfor iron pipes complete all as specified & directed. |
| 56 | S&F in repairs CP Health Faucet with 1 mtr metalic Expandable tube & hook complete all as specified and directed. |
| 57 | S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed. |
| 58 | S&F in repair stop valves/angle valves fancy typechromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unionsfixed for 15 mm dia bore pipe complete all as specified and as directed. |
| 59 | S&F in repair 15mm bore Pillar Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedcomplete all as specified & directed. |
| 60 | S & F 500 ltr capacity rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top)with Ball brass valves, high pressure, with20 mm polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed in position inclrefixing of inlet, outlet & over flow pipe all as specified in SSR Part I. |
| 61 | S & F 1000 ltr capacity rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top)with Ball brass valves, high pressure, with20 mm polythene float and flynut complete, screwed for iron pipe or brass ferrule hoisted and fixed in position inclrefixing of inlet, outlet & over flow pipe all as specified in SSR Part I. |
| 62 | Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75MM/100mm/150MM complete all as specified & directed. |
| 63 | S&FPVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed. |
| 64 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed. |
| 65 | M&L for PCC 1:3:6type C-2 (using 40mm grade stone aggregate) as in bed to drain pipe 110/100 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 66 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 67 | S & F PVC(SWR) bends/sockets any radius 110 mm dia complete all as specified and directed. |
| 68 | S& F stack clamp,110mm/75mm bore made out of 50mm by 5 mm flat iron/pvc and 16 mm dia round stays including bolts and nuts and securing ends of stay to wall or roof complete all as specified and directed. |
| 69 | M&L for Excavation in post holes (or similar holes) each not exc 0.5 cum getting out, returning filling in and rammin earth or broken rubble mixed with earth around in layers not exc 25 cm watering, and removing surplus soil to a distance not exc 50mtr and making good surface in soft/loose soil complete all as specified & directed. |
| 70 | M & L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified & directed. |
| 71 | Demolition of brick workor stone boulder masonry built in cement mortar or cement limeincluding all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 72 | M&L for brick work with sub class \"B\" bricks built in CM 1:6 straight orcurved on plan & exc 6 m mean radius with old size bricks complete all as specified & directed. |
| 73 | Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar complete all as specified and directed. |
| 74 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth (without using extra cement)completeall as specified and directed. |
| 75 | M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 76 | M&L for preparation of new plastered surface of walls including cornices, pilasters etc andapplying two coats of oil bound distemper over a coat of 1mm thick wall care puttyincluding washing floors, cleaning glass, joinery, electric fittings,wiring etc of drops and splashes and leaving premise, clean and tidy etc complete all as specified and as directed. |
| 77 | M&L for preparation of new plastered surface of walls including cornices, pilasters etc and applying two coats of weather proof exterior emulsion paint over a coat of primer complete all as specified and directed. |
| 78 | M&L for preparation of newsurfaces of steel and iron work of any description over 10 cm width or girth not otherwise described andapplying two coats of synthetic enamel paint over a coat of red oxide primer in any tint complete all as specified & directed. |
| 79 | M&L for preparation of old painted steel surfaces and on iron work of any description over 10 cm width or girth not otherwise described andapplying one coat (finishing coat) of synthetic enamel paint in any tint complete all as specified and as directed. |
| 80 | S & F draperly rod/Harrison rails of CP of 25 mm dia with fixing brackets, Stops rollers and rings etc complete all as specified and directed. |
| 81 | M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and smooth without using extra cement including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified & directed. |
| 82 | M&L for 100 mm thickPCC 1:3:6, type C-2 (using 40 mm graded stone aggregates) as in sub base/base complete all as specified and directed. |
| 83 | M&L for precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness, M-50 Grade with grey cement and no pigment complete all as specified including preperation of formation bed over 25 mm thick sand cusion and pointed in colour cement mortar 1:3 complete all as specified and directed. |
| 84 | M & L for PCC 1:2:4 type B-1 using 20mm graded aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 85 | S&F Welded steel wire fabric (mesh) Weight N. exc 4 kg per square metre any size supplied and fixed complete to wood or steel members complete all as specified and directed. |
| 86 | M & L Water Proofing treatment on RCC roof etc comprising with the following operations and as specified herein below :-(a) Taking down/scrapping out existing old tarfelt bituminous compound including sweeping, cleaning, washing down to remove dust etc and removing debris to a distance n exc 250m. (b) 15mm thick plastering in cement mortar 1:4 mixed with WPC @3% by weight of cement finished even & smooth and curing for minimum 7 days(c) Preparing & Cleaning of fully dried cement plastered surface(d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per Sqm conforming IS 3384-1986(e) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 Kg per Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied over bituminous primer as specified above application of polymeric membrance shall be by torch application. The overlap shall be minium 100mm on transverse direction and 75mm on longitudinal direction complete all as specified and directed. (d) Applying one coat of aluminium paint over the APP modified membrane @ 0.11 Kg/sqm. |
| 87 | Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including painting if required to match up with existing surfaces complete all as specified and directed. |
| 88 | M&L for point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium dutyconcealed/ surface PVC conduit 20 mm dia or higher and conduit fittings and all accessories with suitable size of Metal flush box zinc oxide plated or PVC non metallic surface mounting type box,as per site requirement, with modular plate and frame of 01 module to 18 module as required at site, for mounting of modular switches, sockets etc including conteneous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed of the following.Note :-(a) Point wiring should be carried out on surface mounted rigid PVC conduit at the places, whereRCC beam, column, truss, roof or false ceiling exists and as per direction.(b)Colour code will be maintained as per IE rule i.e. Red/Yellow/Blue for phases, Black for Neutral and Green for earth wire. (c) Cost of Modular Metal flush box, modular plate and frame deemed to be included in quoted rate for point wiring and the of flush metal box will be decided by the Engr-In-Charge.(d) Make of Modular metal flush box or PVC non metallic surface mounting type box modular plate and frame, switch, socket, regulator, bell push should be same & colour of frame switches match up with the surrounding. (e) Switch, socket, regulator, bell push will be measured and paid separately under respective item, |
| 89 | One light/ fan/bell point controlled by one 1-way switch. |
| 90 | One three pin 5 Amp socket point on same board. |
| 91 | One three pin 5 Amp socket point on independent board |
| 92 | All as peritem No.88 above but one 3 pin socket outlet 15 Amp independent, with copper cable 2.5 Sq mm size with earth continuity coductor of size 2.5 Sq mm. |
| 93 | M & L for circuit/submain wiring alongwith earth wire 2x2.5 sq mm + 1x2.5 sqmm and PVC conduit on wall surface or concealed with FRLS-H, PVC insulated unsheathed, 1100 Volts grade, single core copper conductor cable, drawing in and including new med, grade, suitable size PVC conduit required saddle / hook fastener/ screws etc to fix on wall / chases as directed includingtaking down old submain wiring and making good disturbed surfaces of walls/floors etc complete all as specified and directed.Note: (i) Colour code shall be maintained as per IE rule. (ii) 03 Runs of 2.5sqmm copper cable and one run of PVC conduit shall be measured as 1 RM unit length. |
| 94 | All as per item No.90 above but wiring with 2x4.0 sq mm + 1x4.0 sq mm earth wire |
| 95 | All as per item No.90 above but wiring with 2x6.0 sqmm + 1x6.0 sqmm earth wire |
| 96 | S & F in replacement switch piano flush, button type 5 Amp SP 240 V AC complete all as specified & directed. |
| 97 | S & Fin replacement switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed. |
| 98 | S & Fin replacement bell push, flush type,5 ampSP 240 V AC complete all as specified & directed. |
| 99 | S & Fin replacement socket outlet multipurpose 5 Pin 5 Amp 250 V AC complete all as specified & directed. |
| 100 | S & Fin replacementsocket outlet two in one 6 pin 5 Amp and 15 Ampflush type complete al as specified. |
| 101 | S & Fin replacement Modular switch 1 way 10 A 1 module. |
| 102 | S & Fin replacement Modular switch 1 way 16 A 1 module |
| 103 | S & Fin replacement Modular socket 6 A- 2/3 pin combined 2 module. |
| 104 | S & Fin replacement Modular socket 6/16 A- 2/3 pin combined 2 module. |
| 105 | S & Fin replacement fan Capacitor 2.5/3.15 mfd 230 Volts |
| 106 | S & Fin replacement LED lamp 7W B22 type, AC 230V, complete all as specified and directed. |
| 107 | S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece, 304 grade braided stainless steel connection pipe for HOT and COLD water and can be fixed in same or new location including taking down old geyser and depositing to MES store without any extra cost complete all as specified and directed. |
| 108 | S & F 450 mm long 304 grade braided stenless steel connection suitable for hot & cold water supply with cromium plated brass screwed nuts at both ends with washers fixed in repairs for making water connection for geyser complete all as specified and directed.. |
| 109 | S & F in replacement Heating element for geyser 1500/2000 wattsScrew type /Clamp Type complete all as specified and as directed. |
| 110 | S & F LED lights fitting 1x20W, 220V, AC box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 111 | M & L for rewinding of ceiling fan/exhaust fan of any make/ model/ sweep including removal of existing burnt winding carefully from slots, cleaning the slots throughly with suitable cleaning agent, applying slot insulation and rewinding with enamelled copper conductor of same gauge/same number of turns as that of existing and connecting the coil suitable to operate on 230 V, single phase, AC supply, permanent capacitor type, tapping the winding and applying air drying the winding throughly and complete all as specified and directed. |
| 112 | S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed. |
| 113 | S&F in replacement desert cooler body made of 20 guage PGI sheet suitable for evaporative type desert cooler of size 67x67x87 cm including side panel-03 nos and front grill with 20 guage PGI sheet and water tank height 20 cm and grill with fins, electrical wiring and connection with on/off switch piano type with distribution PVC cup and elbow PVC pipe connection, PVC cable 3 core 23/0.0076-3m with top plug 5 Amps-01 No,15mm float valve-01 including water pump motor complete body internally and externally and all side panel inner and outer side complete all as specified and directed. |
| 114 | S&F LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant with driver and lamp complete all as specified and directed. |
| 115 | S&F LED building Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. |
| 116 | S&F LED luminaire 600 mm x 600 mm, 35/36 watt watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 117 | S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specified and directed. |
| 118 | S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and as directed.Note- i) Old UNSV exhaust fan deposited to E/M store yard at owncost & arrangement. (ii) Item rates are included for fasteners, nut- bolt flexible wire copper 3 core 1.5 sq mm for fixing & connecting. |
| 119 | S&F exhaust fan, steel body AC single Phase. 230V of size size 450 mm sweep heavy duty sweep with, blades, and frame and louvers complete all as specified and as directed.Note- i) Old UNSV exhaust fan deposited to E/M store yard at own cost & arrangement . (ii) Item rates are included for fasteners, nut- bolt flexible wire copper 3 core 1.5 sq mm for fixing & connecting. |
| 120 | S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250/200 mm complete all as specified and as directed.Note- i) Old UNSV exhaust fan deposited to E/M store yard at own cost & arrangement(ii) Item rates are included for fasteners, nut- bolt flexible wire copper 3 core 1.5 sq mm for fixing & connecting. |
| 121 | S & F Plug top 5 Amps 3 pin, complete al as specified and as directed. |
| 122 | S & F Plug top 15 Amps 3 pin, complete al as specified and as directed. |
| 123 | S & F in repair sheet metal enclosure powder coated, DB with double door DB SPN 8 way, 240V with 200 amps rated bus bar complete all as specified and directed. |
| 124 | S& F in repairs MCB SPN 32 Amps, 240V, 10KA, \"B\" Curve complete all as specified & directed . |
| 125 | S& F in repairs MCB SP 6 to 32 Amps, 240V, 10KA, \"B\" Curve complete all as specified & directed . |
| 126 | S& F in repairs MCB TPN / FP63A, 415 V, \"B\" Curve complete all as specified & directed . |
| 127 | S& F in repairs MCB SPN 40 to 63 Amps, 240V, 10KA, \"B\" Curve complete all as specified and directed. |
| 128 | M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the earth plate at a depth of not less than 1.5 mtr below ground level connected to galvanized iron earth lead wire 4.0 mm dia as earthing lead by means of bolts, nuts and washers made out of GI / steel earth strip protected by GI light grade pipe of 40 mm dia and connecting to main panel board / switch board / control board all shown in electrical plate No 3 of SSR Pt I incl PCC chambers in 1:2:4 and RCC cover slab with 8mm dia MS bars reinforced at 10 cm center to center both ways incl earth work like excavation, returning filling back disposal etc complete. Note:- (i) Extra excavation of earth work more then 3.50 mtr shall be measured and paid separately. (ii) The grid of earthing through earth stip to achieved earth resistance less then 01 ohm to 05 ohm shall be deemed into the quoted rate and no extra payment shall be made to contractor. (iii) The test point shall be made after the grid of earthing and algebric sum of the strip shall be measured after 7.5 mtr earth pit. The strip beyond the total sum shall be paid separately. (iv) Earthing will be carried out in presence of users and MES rep with entire satisfaction. (v) Soil shall be provided by contractor from outside the MOD land for refilling the remaining portion of earth pitfor increasing soil conductivity the low rasistivity soil shall be measured and paid separately. |
| 129 | S&F in replacement on-load changeover switch 415 V, 4 pole, 63 A complete all as specified and as directed. |
| 130 | M &L for disconnecting and taking out old unserviceable damaged/burn out cable of any size & make and supplying, laying, jointing and testing LT underground cable, heavy duty cable of size10 Sqmm 4 core,1100 Volts, XLPE insulated and PVC sheathed, armoured, multi-stranded aluminium conductor cable conforming to IS , laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable including cable gland and lugs etc at both ends incl disconnecting and taking out unserviceable damaged cable complete all as specified and directed. Note : Excavation, earth work, cable sand cushioning & cable protection shall be measured separately under relevant items of this schedule. |
| 131 | Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient forlaying cables/pipes etc. including removing cable protection covers/ bricks complete all as specified and directed. |
| 132 | M&L for Returning, filling in, including spreading leveling, watering and well ramming the excavated soil in layers not exceeding 25 cm thick complete all as specified and directed. |
| 133 | M&L for Removal of surplus excavated soil to a distance not exceeding 50 Mtr distance and depositing as directedat a level not exceeding 1.5 mtr above starting point complete all as specified and directed. |
| 134 | Supply and laying Outer dia of 40 mm and inner dia 32 mm DWC (double Wall corrugated) HDPE polyethiline pipe ISI marked including couplers, bends, cap etc. with smooth internal and profiled external surface for non pressure under ground cable complete all as secified and directed. |
| 135 | S&F in replacement post top/gate light lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant with driver and lampcomplete all as secified and directed. |
| 136 | M&L for rapair/ replacement the same with new hermetically sealed Unit (compressor ), Detecting the Gas leakage rectifying vacumising making the deficiency of gas and re-commissioningunit, blower fan motor, replacement of cooling coil, air filter, relay starting, starting capacitor, blower, selector switch, condensercoil in replacement made out of copper pipes and Aluminum FINS, service cleaning with pressor air and water, soapfrom window type and Split type AC 1.5/2.00 Ton capacitycomplete all as specified and directed. |
