|
| 1 | Construction of granular sub-base by providing close graded material spreading to uniform layers with motor grader on prepared surface, mising by mix in place method with rotavater at OMC and compacting with vibratory roilet to achieve the desired density, complete as per clause Morth 401 |
| 2 | Providing, laying spreading and compacting graded storie aggregate to wet mis macadam specification including premixing the material with water at OMC In mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base/ base course on well prepared surface and compacting with vibratory roller to archive the desired density. Morth 406. |
| 3 | Providing and applying priming coat with bitumen VG-10 on prepared surface of granular base induding cleaning of road surface and spraying VG-10 @ 0.75 KG per sqm. using mechanical means MORTH 502 |
| 4 | Providing and applying Tack coat with bitumen VG-10 pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom MORTH 503 |
| 5 | Providing and laying bituminous macadam with 100-120 TPH hot mix plant producing on average output of 75 tonnes per hours using crushed aggregates of specifled grading premixed with bituminous binder@ 3.4% of VG-30 transported to site laid over previously prepared surface with paver finisher to the required grade level and alignment and rolled as per class 501.6 & 501.7 to achieve the desired compaction complete in all respect. MORTH 504 |
| 6 | Providing and laying semi dense bituminous concrete with 100 - Cum 120 TPH type HMP producing on average output of 75 tonnes per hours using crushed aggregate of specified grading premix with bituminous binder 5% of CRMB-55 and filler transporting the hot mix to work site laying with Hydrostatic pavers finisher with sensor control to the required grade level and alignment, roller with smooth wheeled vibratory and tendem rollers to achieved the desired compaction complete in all respect. MORTH 508 |
| 7 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings, etc as per approved pattern and setting in position with cement mortar 13 (1cement 3 coarse sand). Including the cost of required centering, shuttering complete. 1:1.5:3 (1 cement: 15 coarse sand: 3 graded stone aggregate 20mm nominal size) (ch. no.5 item no.4.6.1 sor 2023-24) |
| 8 | Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, TAP. cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge und accordance with applicable specifications DSR-2018 (16.62) |
| 9 | Providing and laying of 80mm thick cc. pre rubber moulded inter locking paver tiles including 40mm thick fine sand bed with over granular sub base GSB and compacted base of wmm but including cicwork I side of interlocking tiles, for proper slope and camber including cost of material abour T&P etc required for proper completition of work CH No-26/sno-1/16.1.1/S0R |
| 10 | Prepration and consoildation of sub grade with power road rollar of 8 to 12 tonne capacityafter excavating earth to an average of 22.5cm depth dressing to camber and consoildating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50meters. |
| 11 | Engagement of JCB including driver and pol |
| 12 | Engagement of tractor trolly including driver and pol |
| 13 | Class -150 brick wark1:4(1cement:4coarse sand) in foundation & plinth including supply of all material labour T&P etc required for proper completion of work. PWD Ch No-6/sno-1/6.1.1/SOR 2023-2024 |
| 14 | 12mm thick plaster with cement and coarse sand of 2.25 FM mortar 1:4 In single coat on fair side of single or half brick wall surface including internal rounded angles chamfers no exceeding 80mm in grith and finished even and smooth. |
| 15 | 15mm thick plaster with cement and coarse sand of 2.25 FM mortar 1:4 in single coat on fair side of single or half brick wall surface including internal rounded angles chamfers no exceeding 80mm in grith and finished even and smooth. |
| 16 | P/L in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work using cement content as per approved design mix including pumping of concrete to site of laying but including the cost of centering shuttering finishing and reinforcement including admixture in recommended proportions as per is-910 |
| 17 | Mild steel tor steel or plain in plain work such as reinforced concrete or reinforced brick work wrought to required shape as necessary incluing bending for poroper completetion of the work and including supply in complete. Please Enable Macros to View BoQ information |
