|
| 1 | Construction of granular sub-base by providing close graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavater at OMC and compacting with vibratory roiler to achieve the desired density, complete as per clause Morth |
| 2 | Providing, laying spreading and compacting graded stone aggregata to wet mix macadam specification including premixing the material with water at OMC in mechanical mox plant carriage of mored material by tipper to site, laying in uniform layers with paver in sub base/ base course on well prepared surface and compacting with vibratory |
| 3 | Providing and applying priming coat with bitumen VG-10 on prepared surface of granular base including cleaning of road surface and spraying VG-10 0.75 KG per sqm. using mechanical means MORTH 502. |
| 4 | Providing and applying Tack coat with bitumen VG 10 pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom MORTH 503. |
| 5 | Providing and laying bituminous macadam with 100-120 TPH hot mix plant producing on average output of 75 tonnes per hours using crushed aggregates of specified grading premixed with bituminous binder 3.4% of VG-30 transported to site laid over previously prepared surface with paver finisher to the required grade level and 5 alignment and rolled as per class 501.6 & 501.7 10 |
| 6 | Providing and laying semi dense bituminous concrete with 100-120 TPH type HMP producing on average output of 75 tonnes per hours using crushed aggregate of specified grading premix with bituminous binder 5% of GRMB-55 and cum filler transporting the hot mix to work site laying with Hydrostatic pavers finisher with sensor control to the required grade level and alignment, roller with smooth wheeledvibratory and tandem rollers. |
| 7 | Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade colour using hot thermoplastic material by fully semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of accordance with applicable specifications, DSR-2018 (16.62) Engineer-in-charge and accordance with applicable specifications. DSR 2018 (16.62) |
| 8 | Providing and laying of 80mm thick c. c. pre rubber moulded inter locking paver tiles including 40mm thick fine sand bed with over granular sub base GSB and compacted base of wmm but including c.c.work i side of interlocking tiles for proper slope and camber including cost of material, abour T&P etc required for proper completition of work CH No 26/sno-1/16.1.1/SOR |
| 9 | Prepration and consoildation of sub grade with power road rollar of 8 to 12 tonne capacityafter excavating earth to an average of 22.5cm depth dressing to camber and consoildating with road roller including making good the undulations etc and re-rolling the sub grade and disposal of surplus earth with lead upto 50meters |
| 10 | Engagement of JCB including driver and pol |
| 11 | Engagement of tractor trolly including driver and pol |
| 12 | Class -150 brick work1:4(1cement:4coarse sand) in foundation & plinth including supply of all material labour T&P etc required for proper completion of work PWD Ch No-6/sno-1/6 1.1/SOR 2023-2024 |
| 13 | 12mm thick plaster with cement and coarse sand of 2.25 F.M mortar 1:4 In single coat on fair side of single or half brick wall surface including internal rounded angles chamfers no exceeding 80mm in grith and finished even and smooth. |
| 14 | P/L in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of laying but including the cost of centering shuttering finishing and reinforcement including admixture recommended proportions as per is -910. |
| 15 | Mild steel tor steel or plain in plain work such as reinforced concrete or reinforced brick work wrought to required shape as necessary incluing bending for poroper completetion of the work. Please Enable Macros to View BoQ information |
