|
| 1 | SH: BUILDING |
| 2 | EXCAVATION AND EARTH WORK |
| 3 | Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30cm size, saturated soil and rock), lift upto 1.50m and stacking the excavated soil not more than 3m clear from the edge of the excavation and returing the stacked soil in 15cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 4 | Re-filling excavated earth in foundations and plinth etc. In 15 cm layer including ramming and water etc. Complete |
| 5 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete |
| 6 | 4.CONCRETE WORK |
| 7 | Providing and laying in foundations and plinth cement concrete 1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) excluding the cost of centring and shuttering. |
| 8 | Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) |
| 9 | Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by manufacturers. |
| 10 | Applying a coat of hot bitumen (mashphalte 80/100 or equivalent) using 1.70 kg. per sqm. on damp proof course after cleaing the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 11 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 12 | 5.R.C.C. WORK |
| 13 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in: |
| 14 | M20 (1 cement : 1.5 cparse samd : 3 stone aggregate 20mm nominal size) |
| 15 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement : 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement. |
| 16 | a. M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size). |
| 17 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1:3 (1 cement :3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. |
| 18 | a. M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size). |
| 19 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) |
| 20 | Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size) |
| 21 | Centring and shuttering including strutting, propping etc. and removal of form work for: |
| 22 | Foundation, footings, bases of columns etc. and mass concrete. |
| 23 | Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5m height) |
| 24 | Lintels, beams, girders, bressumers and cantilevers etc. |
| 25 | Colum, pillars, posts and struts etc |
| 26 | STEEL REINFORCEMENT |
| 27 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 28 | b) Tar/ TMT steel |
| 29 | BRICK WORK |
| 30 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand). |
| 31 | Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level. |
| 32 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1cement: 4 coarse sand) in foundation and plinth. |
| 33 | ROOFING AND TERRACING |
| 34 | Lime concrete terracing on roofs average thickness 10 cm laid to fall with 25 mm gauge brick ballast and 50% mortar consisting of 1lime putty and 2 surki finished with gur and belgiri treatment complete. |
| 35 | Grading Roof for water proofing treatment with: Lime Concrete with 20mm nominal size brick aggregare & 50% lime mortar 1:2 (1 lime putty :2 surkhi) |
| 36 | Providing gola 75 x 75 mm in cement concrete 1:2;4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1 : 3 ( 1 cement : 3 fine sand) as per standard design : |
| 37 | Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown or/ and residual bitumen applied hot @ 1.45kg per sqm. of area for each courese, second course of roofing felt type-3 grade-1 (hessian base self finished bitumen felt) and fourth and final course of stone grit 6mm and down size or pea size gravel spread at 6 Cu.dm. per sqm. including preparation of surface excluding grading complete. |
| 38 | Providing and fixing on wall face C.I Rain water pipes including filling the joints with spun yarn soaked in neat cement slurry & cement mortar 1:2. |
| 39 | 100 mm diameter |
| 40 | Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10mm x 10cm x 10cm of 1:2:4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. |
| 41 | 100 mm diameter |
| 42 | Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) |
| 43 | b)- CI Plain Bend-100mm dia |
| 44 | b)- CI Plain shoe-100mm dia |
| 45 | Making khurras 45 x 45 cm with avg. minimum thickness of 5 cm cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 mm x 1 m x 400 micron, finished with 12 mm cement plaster 1 : 3 ( 1 cement : 3 coarse sand) and finishing the outlet complete as per drawing. |
| 46 | WOOD WORK |
| 47 | Providing approved best local wood ( Class-B II) work in frames of doors , windows clerestory windows and other frames , wrought framed and fixed in position.(490.70 per Ten Cudm) |
| 48 | Providing and fixing flush door shutters,decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 49 | a)40mm thick including anodized aluminum butt hinges with necessary screws. |
| 50 | Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size). |
| 51 | Providing and fixing aluminum handles anodised transparent or dyed to required color or shade with necessary screws etc complete. |
| 52 | 100 mm |
| 53 | Providing and fixing aluminium Tower bolts anodized or transparent or dyed to required color or shade with necessaryscrews etc complete. |
| 54 | a) 300 x 10 mm |
| 55 | Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. |
| 56 | a) 300 x 16 mm |
| 57 | Providing and fixing 50 cm long aluminium kicking plate 100x3.15mm anodised, transparent or dyed to required color or shade with necessary screws etc. complete. |
| 58 | Providing and fixing chromium plated finished 100mm mortice latch and lock with 6 levers and a pair of CP handles with necessary screws etc. |
| 59 | Providing and fixing aluminium floor door stopper anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade withnecessary screws, etc. complete.a) Twin rubber stoper(Except Toilet doors)-D3 |
| 60 | 11. FLOORING |
| 61 | Providing and laying vitrifiedfloor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption\"s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. |
| 62 | Size of Tile60x60 cmrefer carpet area calculation |
| 63 | SKIRTING/ DADO : Providing and laying vitrifiedfloor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption\"s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 12mm thick cement mortar 1:3 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. |
| 64 | size of tile 600x600 mm |
| 65 | Providing and fixing 1 st quality ceramic glazed wall tiles confirming to IS: 15622 ( thickness to be specified by manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any sizes as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 Cement : 3 Coarse sand) and joining with grey cement slurry @3.30kg per sqm including pointing with white cement mixed with pigment of matching shade complete. |
| 66 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x30mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. sqm 1225.10 shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete. |
| 67 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of area less than 0.50 sqm |
| 68 | 10. STEEL WORK |
| 69 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 70 | 13. FINISHING |
| 71 | 12 mm thk cement plaster 1: 4( 1 cement : 4 coarse sand) on walls. |
| 72 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement :4 fine sand) |
| 73 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 74 | Finishing walls with water proofing cement paint of required shade : |
| 75 | Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade. |
| 76 | Applying priming coat: |
| 77 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works. |
| 78 | With ready mixed pink primer of approved brand and manufacture on resinous wood and plywood works. |
| 79 | painting with synthetic enamel paint of approved brand and manufacture to give an even shade- 2 or more coats |
| 80 | Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with aluminum paint of approved quality over a priming coat of ready mixed genuine red lead on new work. |
| 81 | 20. ALUMINUM WORK |
| 82 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections ofapprovedmakeconformingtoIS:733andIS:1285,fixedwithrawlplugsand screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequiredincludingcleatangle,Aluminiumsnapbeadingforglazing/ panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings andthedirectionsofEngineer-in-charge.(Glazingandpanellingtobepaidfor separately) : |
| 83 | Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868 |
| 84 | Providingandfixingglazinginaluminiumdoor,window,ventilatorshuttersand partitionsetc.withPVC/neoprenegasketetc.completeasperthearchitectural drawings and the directions of engineer-incharge.(Cost of aluminium snap beadingshall be paid in basic item)With float glass panes of 5.5 mm thickness. |
| 85 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-incharge complete. 255 X 19 mm. |
| 86 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @200mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section arcound the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment) windows area @ 2.07Kg/m. |
| 87 | Subheads :- internal & external electrification |
| 88 | Supplying and fixing conduit |
| 89 | Supplying and fixing conduit 32mm along with the accessories and surface pvc i/c painting complete etc. |
| 90 | Supplying and fixing 25mm pvc conduit along with accessories complete etc. |
| 91 | Supplying and fixing 19/20mm pvc conduit along with accessories and surface |
| 92 | Insulated Wiring on surface conduit |
| 93 | Wiring for light point with 1.5mm pvc insulated Al. conductor cable in surface conduit i/c painting complete etc. a) Medium point |
| 94 | b) Long point |
| 95 | Wiring for fan point with 1.5sqmm pvc insulated Al. conductor cable in surface pvc conduit completea) Long point |
| 96 | Wiring for exhaust fan - do-a) Long point |
| 97 | Wiring for calling bella) Long point |
| 98 | Wiring for 3pin 5Amp plug pointa) Short point |
| 99 | Wiring for 3pin 15Amp plug point with 4sqmm pvc insulated Al. conductor cablea) Long point |
| 100 | Wiring for circuit wiring 2 x 1.5 sqmm pvc insulated Al. conductor cable in the surface pvc conduit including painting etc as complete. |
| 101 | Wiring for circuit wiring 2 x 2.5sqmm pvc insulated Al. conductor cable in the surface pvc conduit i/c painting etc. as complete. |
| 102 | Wiring for circuit wiring 2 x 4sqmm pvc insulated Al. conductor cable in the surface pvc conduit i/c painting etc. as complete. |
| 103 | Supplying and fixing metal boxes |
| 104 | Supplying and fixing metal boxes 300 x 450 x 100mm deep in with suitable |
| 105 | Supplying and fixing Accesssories |
| 106 | Supplying and fixing 5Amp switch on the existing wooden board |
| 107 | Supplying and fixing 5Amp socket |
| 108 | Supplying and fixing 15Amp switch |
| 109 | Supplying and fixing 15Amp socket |
| 110 | Supplying and fixing ceiling rose on the existing wooden board including connection as required |
| 111 | Supplying and fixing fairly wall bracket of anodized al. 12mm dia. Pipe fixed on 3mm thick 170mm x 40mm painted ms. Plate brass bracket holder complete |
| 112 | Supplying and fixing bulkhead fitting suitable for 100watt lamp complete with accessories |
| 113 | Supplying and fixing call bell/buzzer and bell push suitable for AC/DC single phase 230 volts complete as required |
| 114 | Installation testing commissioning of flurescent fitting |
| 115 | Installation testing commissioning of ceiling fans and regulator as complete |
| 116 | Installation of exhaust fan upto 450mm sweep in the existing opening |
| 117 | Being cost of ceiling fan polar/orient |
| 118 | Being the cost exhaust fan |
| 119 | Being the cost electric Gyser superior quality |
| 120 | Being the cost of room heater Bajaj cool and warm |
| 121 | Being the cost call bell and push |
| 122 | Being the cost of fairly wall bracket of superior quality |
| 123 | Supplying and fixing fairly tube light with frame decorative type |
| 124 | METAL CLAD FUSE UNIT/D.B BOX |
| 125 | Providing and fixing 100Amp SPWN switch fuse unit 240/250 Volti/c drilling holes on the board connection earthing the body etc. as required.Catogory A |
| 126 | Providing and fixing 6 way metal clad DB-240 /250 Volts15Amp per way including drilling holes on the board connection, earthing the body etc. as required |
| 127 | EARTHING |
| 128 | Earthing with copper plate 600mm x 600mm x 3mm thicki/c accessories and providing masonry enclosure with cover platehaving locking arrangement and watering pipe complete as required |
| 129 | Supplying and laying 8SWG copper wire at 0.50mtr. Below ground level asconductors earth electrode i/c soldering etc. required |
| 130 | WOODEN BOARD |
| 131 | Supplying of wooden board with sunmica finished6\" x 8\" |
| 132 | 4\" x 8\" |
| 133 | 4\" x 4\" |
| 134 | Add 100% CI on above items except item no 12to 18 of Accessories i.e on Rs 83150.15 |
| 135 | Add 20% increase in market rate on Rs |
| 136 | Add 4% for unforseen item if any on Rs |
| 137 | MCCB Board with fittings |
| 138 | Wire cable 16 mm |
| 139 | Circuit Wire 6 mm,2.5mm,1mm&0.5 mm |
| 140 | Copper plate earthing copper wire |
| 141 | ST light pole iron |
| 142 | Panel Board(Change over, Boll metre, ampere metre, RYB indicator) |
| 143 | Sub head : internal & external Sanitation items |
| 144 | Earth work in excavation in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30cm size, saturated soil and rock) including banking in 20cm layers and breaking clods, ramming and dressing up for the purpose of making embankments or filling up ground depressions, lead upto 50m and lift upto 1.50 |
| 145 | Providing and laying in foundations and plinth cement concrete1:4:8 (1cement :4coarse sand: 8 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering. |
| 146 | Providing and laying c.c 1:3:6 (1cement: 3coarse sand: 6stone aggregates of 20mm nominal size) excluding the cost of centering and shuttering. |
| 147 | Providing and laying in foundations and plinth cement concrete 1:2:4 (1cement: 2coarse sand:4 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering. |
| 148 | RCC work in suspended floors, roofs and balconies upto floor two level including finishing and plastering the exposed surface with CM 1:3 (1cement: 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but excluding cost of centering and shuttering and reinforcement with 1:2:4 (1cement;2coarse :4stone aggregate 20mm nominal size). |
| 149 | Centering and shuttering including strutting, propping etc and removal of formwork for |
| 150 | a) Foundation, footing bases of column, steps |
| 151 | 1) Septic tank |
| 152 | 2) Suspended floor |
| 153 | Reinforcement of RCCwork including bending, binding and placing in position complete. |
| 154 | 15mm thick cement plastering with 1:3 (1cement:3fine sand) inside the septic tank and inspection chamber |
| 155 | Neat cement punning |
| 156 | Providing and fixing white vitreous china type water closet pedestal (European type wc pan) with seal and lid CP brass hinges and rubber buffers, 12.5 litres high level CI flushing cistern with fittings RS or CI brackets |
| 157 | P/Fixing wash basin 550X400mm |
| 158 | Providing and fixing pair of foot rest |
| 159 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass. |
| 160 | Providing and fixing toilet paper holder |
| 161 | a) CP Brass |
| 162 | Providing and fixing kitchen sink including making all connection excluding cost of Fittings. |
| 163 | P/Fixing SCI Soil waste and vent pipe 100mm |
| 164 | P/Fixing SCI heel rest, sanitary bend |
| 165 | P/Fixing SCI single equal junction (100x100x100)mm |
| 166 | P/Fixing brasss chain and rubber plug for sink or wash basin |
| 167 | P/Fixing fisher union for wash basin and sink 40mm dia |
| 168 | Providing and fixing 600x120mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws |
| 169 | Construction of soak pit 2.50 dia 3m deep with 45x45 cum dry bricks honey comb shaft and sw drain 100x1.80mtr long complete as per standard design. |
| 170 | P/Fixing GI Pipe 15mm dia(internal) |
| 171 | P/Fixing GI pipe 20mm dIa(external) |
| 172 | P/Fixing bib cock 15mm dia |
| 173 | P/Fixing brass stop cock of approved quality |
| 174 | a) 15mm nominal bore |
| 175 | b) 20mm nominal bore |
| 176 | Providing and fixing non-return valve of approved quality.A) 50mm nominal bore |
| 177 | Proving and fixing ball valve (brass) of approved quality complete. A) 20mm nominal bore |
| 178 | Providing & fixing PVC connection with brass union 30 cm length |
| 179 | SUB HEAD: BOUNDARY WALL |
| 180 | Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto1.50 m and stacking the excavated soil not more than 3m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sidesof foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 181 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 182 | Providing and laying cement concrete1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:a) Foundations and plinth |
| 183 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcementin :b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) |
| 184 | Reinforced cement concrete work in lintels,beam sand bresumers upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.b)1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 185 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) |
| 186 | Centring and shuttering including strutting, propping etc and removal of formwork for : |
| 187 | a) Foundation, footings, bases of columns etc. and mass concrete. |
| 188 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 189 | e) Column, pillars, posts and struts etc. |
| 190 | Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth. |
| 191 | Extra for pre-cast cement concrete block masonry in superstructure above plinth level up to floor two level. |
| 192 | Reinforcement of RCC work including bending, binding and placing in position complete.b) Tor/TMT steel. |
| 193 | Carriage of material by mechanical mean Cement |
| 194 | Sand (quarry to work site ) |
| 195 | Aggregate (quarry to work site) |
| 196 | Steel |
| 197 | Carriage of material by Head load |
| 198 | Cement |
| 199 | Sand (quarry to work site ) |
| 200 | Aggregate (quarry to work site) |
| 201 | Steel |
