Tender For Addition / Alteration, Interior & Miscellaneous Works In Editorial Section, Director Office And Conference Room Of Ncpul Building At Institutional Area, Jasola, New Delhi.
Tender Value
21.89 Lakhs
Estimated cost
Bid Submission
04 Dec 2025
0 days left
EMD
43800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition / Alteration, Interior & Miscellaneous Works In Editorial Section, Director Office And Conference Room Of Ncpul Building At Institutional Area, Jasola, New Delhi.
BOQ
| Sl. No. | Item Description |
| 1 | Laying and Jointing PVC Pipe. Heading |
| 2 | EARTH WORK - ANTITERMITE TREATMENT: Supplying, diluting and injecting chemical emulsion of chlorpyriphose emulsifiable concentrate of 20% for post constructional anti termite treatment(a) Treatment at points of contact of wood work by chemical emulsion chlorpyriphos (in oil or kerosene based solution) @ 0.5 litre per hole by drilling 6mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. |
| 3 | CONCRETE WORK: Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of cantering, shuttering and finishing : (a) 1:2:4 (1 Cement: 2 coarse sand (zone III) derivedfrom natural sources : 4graded stone aggregate 20 mm nominal size derivedfrom natural sources) |
| 4 | RCC Work” Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforced cement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for (a) Shelves (Cast in situ) |
| 6 | (b) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (a)Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | MASONRY WORK Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Superstructure aboveplinth level up to floor v level in all shapes and size in: (a)Cement Mortar 1:4 (1cement :4 coarse sand) |
| 9 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. (a) Cement mortar 1:3 (1 cement :3 coarse sand) |
| 10 | CLADDING WORK Providing and fixing 18 mm thick gang saw cut, mirror polished, premolded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. (a) Granite stone slab of all colour black, Cherry/Ruby redArea of slab upto 0.50 sqm |
| 11 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 12 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc.including moulding, rubbing and polishing of cut edges etc. complete. |
| 13 | Providing and fixing Ist quality ceramic glazed wall tiles of 450mm x 300mm, 600mm x 600mm, 600mm x 1200mm or as decided by architect conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete . |
| 14 | Extra for fixing glazed/ceramic/vitrified wall/floor tiles with cement bound high polymer modified quick set lite adhesive(water based) confirming to IS:15477 in average 6mm thickness in the basic item |
| 15 | WOOD AND P.V.C. WORK Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia& length (holdfast lugs or dash fastener shall be paid for separately). (a) Sal wood |
| 16 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 17 | Providing and fixing wooden moulded beading to door and window frames with iron screws,plugs and priming coat on unexposed surface etc. Complete: (a) 2nd class teak wood(i) 50x12mm |
| 18 | Providing40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) or dash fastener of required size. |
| 19 | Providing and fixing aluminiumextruded section body tubular type universal hydraulicdoor closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kgand door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 20 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper |
| 21 | Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including cost of adhesive of approved quality. (a)1.0 mm thick |
| 22 | (b) 1.5 mm thick |
| 23 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x mm first class kail wood, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary nailng/ stainless steel screwsat junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved wood primer etc. complete, all as per direction of architect/Engineer/ Competent Authority. |
| 24 | Providing and fixing in wall lining with ply woodBWP grade and termite proof of approved brand on wall / existing wooden / Steel frame work with necessary fixing arrangement and screws etc. complete as per direction of architect/Engineer/ Competent Authority.( Frame work to be paid for separately) (a)12mm ply wood |
| 25 | (a) 6mm thick ply wood |
| 26 | Providing and fixing PVC wall panel of approved brand/shade including fixing with nails/screws all complete as per direction of architect/competent authority: 12mm thick |
| 27 | STEEL WORK: Welding by gas or electric plant including transportation of plant at site etc. complete. |
| 28 | FLOORING: Providing and fixing wooden flooring of required size and fixing with adhensive of approved make as per direction of Competent Authority.(a) 8mm thick |
| 29 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (a) Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm or as decided by Competent Authority. |
| 30 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. |
| 31 | Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymermodified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3 mm thickness. |
| 32 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. (a) Size of Tile 600x600 mm |
| 33 | ROOFING: Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both sideinclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (a) 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 34 | FINISHING 12 mm cement plaster of mix (a) 1:4 (1 cement: 4 coarse sand) |
| 35 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement. (a) 20 mm cement plaster |
| 36 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : (a) Two or more coats on new work |
| 38 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 39 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. (a)Two or more coats on new work |
| 40 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. (b)Two or more coats on old work |
| 41 | Appling priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. (a) With water thinnable cement primer on wall surface having voc content less than 50 grams/litre |
| 42 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping ,sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete: |
| 43 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 44 | French sprit polish using spray polish machine including scraping, sand-papering/rubbing the existing surface and filling the scratches with filling material etc complete in two or more coats to give smooth and even surface including shifting of books etc complete as per direction of competent authority. |
| 45 | REPAIRS TO BUILDINGS Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. (a) With cement mortar 1:4 (1 cement : 4 coats sand) |
| 46 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls flooring and jambs complete, to match existing surface i/c disposal of malba/rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-In-Charge. (a) For door /window/clerestory window |
| 47 | Dismantling W.C.Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. |
| 48 | Dismantling vitreous china half stall / flat back lipped front urinal / wash basin, sink of different sizes, including stacking of serviceable materialsuch as CIbrackets ,CP brass fittings, flushpipe stainless steel PVC connection etc. near theside and disposal of unsolvable material with in 50 metre lead. |
| 49 | Dismantling 15 to 50 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per directions of Engineer-in- Charge. (a) Internal work – concealed /exposed on wall |
| 50 | DISMANTLING & DEMOLISHING Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. (a) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 51 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of competent authority |
| 52 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of competent authority: (a) In cement mortar |
| 53 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : (a) Of area 3 sq. metres and below |
| 54 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. (a) For thickness of tiles 10 mm to 25 mm |
| 55 | Dismantling aluminum / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stackingof serviceable material within 50 meters lead as directed by competent authority. |
| 56 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 57 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 58 | Dismantling wooden tile flooring wherever required including stacking of serviceable material and disposal of unserviceable materialfrom all height of building for all lead and lift: thickness of tile upto 15mm |
| 59 | Labour for cutting existing CI/SCI/UPVC pipes with steel saw / mechanical device in sanitary shaft at any heightfor fixing of fittings such as collar, junction, bend etc. as required at siteas direction of competent authority :100mm dia SCI/ UPVC pipe |
| 60 | Dismantling wooden wall panelling and partition including supporting farm work (steel or wood)and stacking of serviceable material and disposal of unserviceable materialfrom all height of building for all lead and lift as direction of competent authority |
| 61 | Taking out wooden cabinet/ almirahof any size without dismembered and staking at site as per direction ofcompetent authority (front elevation area to be measured) |
| 62 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 63 | Disposal of building rubbish / malba/ similar unserviceable dismantled of waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer- in – charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 64 | SANITARY INSTALLATIONS Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 65 | Extra for using round/ oval shape counter top wash basin of size 560x400x200mm/ 560x410mm hindwer, cera or as approved the competent authority in basic items |
| 66 | Providing and fixing 8 mm dia C.P./ S.S jet with S.S triangular plate or CP / SS hand shower with flexible tube upto 1 meter long with to European type WC of quality and make as approved by Engineer-in charge. |
| 67 | Providing and fixing CP brass 32mm size bottle trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 68 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 69 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe |
| 70 | Providing and fixing trap of self cleansing design without vent arm complete, including cost of cutting and making good the walls and floors : (a) Sand cast iron S&S as per IS - 3989(i) 100 mm inlet and 100 mm outlet |
| 71 | Providing and Fixing Stainless Steel grating 125mm dia with or without waste hole for floor traps including fixing with white cement etc. Complete. |
| 72 | Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729 |
| 73 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729 |
| 74 | Providing and fixing collar :100 mm Sand cast iron S&S as per IS - 1729 |
| 75 | Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 100 mm dia |
| 76 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 77 | WATER SUPPLY Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. (a) INTERNAL WORK – EXPOSED ON WALL (i) 20 mm nominal dia pipes |
| 78 | (ii)25 mm nominal dia pipes |
| 79 | (iii) 32 mm nominal dia pipes |
| 80 | (iv) 50 mm nominal dia pipes |
| 81 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (a) Concealed work, including cutting chases and making good the walls etc.(i) 20 mm nominal outer dia Pipes |
| 82 | (ii) 32 mm nominal outer dia Pipes |
| 83 | Providing and fixing uplasticised PVC connection pipe with brass unions : (a) 45 cm length (i) 15 mm nominal bore |
| 84 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (a) 15 mm nominal bore |
| 85 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (a) 15 mm nominal bore |
| 86 | Providing CP brass extension nipple size 15 mm x50mm of approved make and quality as per direction of Engineer –in charge |
| 87 | Providing and fixing stainless steel towel rod 600 mm long of approved make and quality.Including with necessary PVC rowel plug and CP brass screws etc.complete |
| 88 | Providing and fixing CPVC ball valve with handle of approved brand and manufacture as approved by engineer-in-charge /competent authority.(a)20 mm dia meter |
| 89 | (b)32 mm dia meter |
| 90 | ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size , including necessary filling up the gaps at junctions, i.e.at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer –in-charge. (Glazing, panelling and dash fasteners to be paid for separately): (a) For fixed portion (i) Powder coated aluminium ( minimum thickness of powder coating 50 micron) |
| 91 | (b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately): (i) Powder coated aluminium ( minimum thickness of powder coating 50 micron) |
| 92 | Providing and fixing glazing in aluminium doors, windows, ventilators shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per architectural drawings and the directions of Engineer –in-charge. (cost of aluminium snap beading shallbe paid in basic item): (a) With float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm) |
| 93 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. (a) With stainless steel cover plate minimum 1.25 mm thickness |
| 94 | Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 95 | Providing and Fixing American aluminiumhandle -200mm powder coated (minimum thickness of powder coating 50micron) for aluminium door shutter. |
| 96 | Providing and Fixing aluminium tower bolt -250mm x10mm powder coated (minimum thickness of powder coating 50micron) for aluminium door shutter. |
| 97 | Providing and fixing stainless steel single lever hanger of approved quality in wall / door or other suitable place with necessary screws etc complete. |
| 98 | Taking out aluminium door shutter (single/double) including chaukhat of any size and re-fixing the same on other location after repairing by cutting or dismembering including glazing, fittings, floorspring etc. and repair the same as per opening including screws, cleets, new prine/gasket etc wherever required are complete as per direction of competent authority(If new aluminium sections, floorsprings, glazing are used which will be paid in the basic item or separately) |
| 99 | WATER PROOFING Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with waterproofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 100 | MISCELLANEOUS ITEMS Fabrication and installation of work station with overhead storage cabinet, working table, partition etc (Excluding side cabinet)as per architectural drawing No AC/NCPUL consisting the following items(i) Wooden frame work made offirst class kail wood plank/ scantling 50mmx 50mm and 600mm centre to centre horizontally and vertically both or as per site condition (ii) Fixing of 12mm thick ply woodBWP grade and termite proof on both sides of frame work with nails / screws of required sizes (iii) Fabricating overhead cabinet and table top of work station with 18mm thick block board BWP grade and termite proof of approved quality including back support with 6mm thick ply wood BWP grade and termite proof. (iv) Finishing exposed surface of ply / block board with 1.5mm thick laminate of approved brand.(v) Each seat of workstation having facility of keyboard with channel/ runner. (vi) Overhead cabinet having aluminium handle 75mm, cupboard lock and magnetic catcher of approved brand. (vii) Half round moulding, lipping of required size made of second class teak wood. (viii) Fixing of green pinup board 12mm thick (ix) Painting of inside overhead cabinet and moulding /lipping etc. with two coats of approved synthetic enamel paint including priming coat (A) Six seater work station |
| 101 | (B) Two seater work station |
| 102 | (C)one seater work station |
| 103 | Fabrication and installation of cupboard made of 18mm thick block board and 12mm thick BWP grade and termite proof plywood and 1.0 mm thick laminate, inside painting with synthetic enamel paint two or more coats including priming coat and fittings such as aluminium handles cupboard lock of approved brand with full threaded steel screws in partition, boxes, shelves, racks and cupboard kitchen cabinet, under kitchen counter etc all complete as per direction of architect / engineer, competent authority : approximatedimensions 110cmx50cmx210cm (for payment front elevation area to be measured) |
| 104 | Fabrication and installation in position book rackmade of 18mm thick block boardand 12mm thick ply woodBWP grade and termite proof of approved brand with full threaded steel screws finished with 1.5mm thick laminate and painting with two coats of synthetic enamel paint of approved brand including priming coat etc complete as per architectural drawing and direction of architect (for payment front elevation area only one side to be measured)(A) Book rack (Module A) of size 1.20m x2.00m |
| 105 | (A) Book rack (Module B) of size 0.903m x2.00m |
| 106 | (B) Book rack (Module C) of size 0.90m x1.75m |
| 107 | (C) Book rack (Module D) of size 1.20m x2.00m |
| 108 | Taking out workstation with overhead storage cabinet, working table, dwarar etc including dismembering wherever required and re-assembled at first floor or any other floor NCPUL building including cost of lifting etc complete as direction of architect / competent authority (A) Four seater workstation |
| 109 | (B) Twoseater workstation |
| 110 | Fabrication and installation in position of side unit made of 18mm thick block board and 12mm thickply wood BWP grade and termite proof consisting the following items & as per (architectural drawing as shown in item of work station)direction ofarchitect / competent authority (i) Side cabinet box / body made of 18mm thick block board and 12mm thick ply on back side. (ii) Two nos drawers made of 18mm thick block board & 6mm thick ply on bottom and two set of telescopic drawers channel. Lower portion of cabinet having shutter made of 18mm thick block board fixed with stainless steel piano hinges with screws. Fixing 1.5mm thick laminate of approved brand and shade on exposed surface. Fixing of aluminium door handle 75mm and CP brass cupboard lock 50mm in shutter & drawer including magnetic catcher Fixing liping made of second class of size 18x5mm including painting and priming coat. Inside painting with synthetic enamel paint two or more coats including wood primer and outside exposed surface also. |
| 111 | Dismembering & cutting of existing conference table and to make / re-assemble for suitable of at least seating capacity of 20 persons or more as per architectural drawing as well as direction of architect/ competent authority – Job work |
| 112 | ELECTRICAL WORKLED Down Lighter (COB Type) (System lumen efficacy >_ 105 < 120 Im/Watt). Supplying, installation, testing and commissioning of LED recessed/surface down lighter (round/square/rectangular) COB Type of following body material and construction as peer IS : 10322 with driver as per the requirement with Driver efficiency > 85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, operating temp range -5 degree Celsius to 40 degree Celsius, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P.F >_ 0.95, IP20, CRI >_80, UGR (Unified Glare Rating) <_ 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000 degree Kelvin / 4000 degree Kelvin/5700 degree Kelvin/ 6500 degree Kelvin (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq. mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >_ 105 and <120 Im/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management heat sink of aluminium housing such that LED junction temperature shall not rise above 90 degree Celsius) Powder coated die cast/ Extruded aluminium Body including trim with Aluminium Reflector (a)22 watt |
| 113 | Supplying, installation, testing and commissioning of LED tube light 20 watt- 2100 luminous, 1200 mm (4 feet) long of approved brand such as Philips, Crompton or equivalent including taking out existing tube light, replacing the supportor, holder wherever required and stacking old tube light etc complete. |
| 114 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required . (a)20mm |
| 115 | (b) 25mm |
| 116 | Supplying and fixing of following sizes/ modules, GI box along with modular base and cover plate or modular switches in recess etc as required.(a)1 or 2 module (75mmx75mm) |
| 117 | (a) 6 module (200mmx75mm) |
| 118 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface /recessed steel / PVC conduit as required. (a) 1x1.5 sqmm |
| 119 | (b) 2x2.5 sqmm |
| 120 | Supplying and drawing followingpair 0.5 mm dia FRLS PVC eannealedcopper conductor, unarmoredtelephone cable in existing surface /recessed steel / PVC conduit as required. (a)2 pair |
| 121 | Supplying and drawing internet cable cat 6grade PVC insulated copper conductor, in existing surface /recessed steel / PVC conduit as required. (a)1 pair |
| 122 | Supplying and fixing of following modular switches / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (a)15/16 A switch |
| 123 | (a) 3pin 5/6A socket outlet |
| 124 | (b) Telephone socket outlet |
| 125 | (c) TV Antenna socket out let |
| 126 | (d) Internet socket outlet |
| 127 | (e) 5/6A switch |
| 128 | Wiring for light/power plug with 2x4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit along with 1 No. 4 sq. Mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthling as required |
| 129 | Supplying and drawing co-axial TC cable RG-6 grade, 0.7mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVS sheath in the existing surface/recessed steel/PVC conduit as required. |
| 130 | LED Panel light 2x2 ft. (System lumen efficacy >_120 <135 Im/Watt) Supplying, installation, testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS “10322 with driver as per the requirement with Driver efficiency > 85%, operating voltage AC 140-270 volt, frequency 50/60 hz, operating temp range -5 degree Celsius and 40 degree Celsius, internal surge protection of 2.5 KV with Short & Open circuit protection, THD<10%, P.F. >_0.95, IP20, CRI>_80, UGR (Unified Glare Raing) <_19, Flicker free, (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000 degree Kelvin/4000 degree Kelvin/5700 degree Kelvin/6500 degree Kelvin (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and fixture shall be of relevant BIS standard. Manufactures Word Mark/Name Engraved/Embossing /Screen printing on housing complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthling etc. as required with minimum 5 year OEM warranty. System lumen efficacy > 135 Im/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90 degree Celsius) Powder coated i.e. cast/extruded aluminum body (Thickness>_1.20mm) (i) 36Watt |
| 131 | (ii) 22 Watt |
| 132 | (iii)18 Watt |
| 133 | (a) Powder Coated CRCA Sheet Body (Thickness >_ 0.50 mm) (i)36Watt |
| 134 | Supplying, installation, testing and commissioning of inverter 5/4/3 star split AC (2025 model) with copper condenser R32 Refrigerant of O General or as approved by architect/competent authority |
| 135 | Dismantling AC duck of any size by cutting mechanical device /manually and taking out accessories of Ac wherever required and stacking the serviceable material and disposal of unserviceable material from all height of building all lead and lift as per direction of competent authority. |
AI Tender Summary
Tender Timeline
Nov 12, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedDec 04, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 08, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender