Tender For Repairs To Wooden Furniture For Married And Otm Accommodation At Fort William Under Ge (Fw) Kolkata.; 1 BED HARD (MAP)[DRG NO : FD/E6/MAP/08(R)] 2 Removing of old unserviceable head board of bed hard and S&F new one 18mm thick Pre-laminated MDF board with ISI mark (ISI-2406)both sideteak shade , exterior gradewith 4 mm teak wood beading and to be fixed withscrew as per drawing and specification complete all as specified and directed. 3 All as per itemNo 1.01 but for foot board . 4 Welding to existing broken/cracked joints of bed hard and grinding forevenand smooth gas weldingcomplete all as specified and directed. (Note :Welding of broken/cracked joints shall be counted one point for one joint). 5 S&F 8mm dia bolts and nuts and tightening the steelframing structure of bedhardas inrepairas per drgand specification complete all as specified and directed. (Note: Each bolts and nutsshall bemeasuredas one unit) 6 M&L removal of old paint from surfaces of steel framing structure and applying two coats ofSynthetic Enamel black paint (first quality) over a coat of red oxide zinc chrome primer , to all sides of steel framing structure of bed hard complete all as specified and directed. 7 Removing of old unserviceable hard rubber shoe from leg and S&F with new one as per existing ofapproved quality complete all as specified and directed. 8 Removing of old unserviceable hard rubber cap from leg and S&F with new one as per existing ofapproved quality complete all as specified and directed. 9 Removing of old unserviceable top ply from bed hard and S&F 12mm thick ply wood (7 ply) commercial of BWR grade, securing withdrilling two holes of each stiffener 8mm dia round headcountersunkbolts and nutswith washer (06 Nos) as perexisting shape and size complete all as specified. 10 Charpoy MS with MNF Set [Drg No : CWE/C/F/04 and FD/MAP-II/01] 11 Removing of old worn out/unserviceable ply top of charpoy MS and S&F 12mm thick (7 ply) BWR gde type BB plywood securing with 8mm dia round headcountersunkbolts and nutswith washer as per existing shape and size complete all as specified and directed. 12 Welding to broken joints of charpoy MS and grinding for even andsmooth gas welding complete all as specified and as directed. (Note : Welding of each broken joints shall be counted as one point) 13 M&L for preparing old steelor iron surface of any description over 10cm width or girth and applying two coats of Synthetic Enamel paint (First quality) Black paint before fixing the ply hard top complete all as specified and directed. 14 Removing of old unserviceable hard rubber shoe from leg and S&F with new one as per existing ofapproved quality complete all as specified and directed. 15 Hat Stand with Mirror [Drg No : FD-233/361/362] 16 Removing of old damaged mirrorand S&F new mirror of 5 mm thick mirror as per drg or as directed by Engr-In-Charge. 17 Removing of old damagedback side ply and S&F new back side ply 6 mm thick BWR quality as per drg or as directed by Engr-In-Charge. 18 Removing old damaged front ply and S&F new frontply 4mmthick BWR quality one side teak faceas per drg or as directed by Engr-in-Charge. 19 Removing of old damagedhooks and S&F new brass hookto Hat standand all as per drg or as directed by Engr-In-Charge. 20 Removing broken/unserviceable hanging clip and S&F new MS Hanging Clips as per suitable size and fix with screw rest all specified by Engr-in-charge. 21 Peg Table [Drawing No : FD-277, 384]Removing following unserviceable components from Peg Table and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 22 M&L removal of unserviceable top of peg table in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade) with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 23 Leg made out of 1st class hard wood (teak) 24 Top rail (shorter) made out of 1st class hard wood (teak) 25 Top rail (longer) made out of 1st class hard wood (teak) 26 PVC hard rubber shoe of approved quality 27 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. Complete all as specified. 28 TABLE CENTRE[Drg No: FD-29M, FD-235 &FD-274]Removing following unserviceable components fromTable Centreand S&F new components as per the following and fixing the same without disturbing the other parts including polishing complete wherever shown on drawing and making functional the furniture as per drg and specification. 29 M&L removal of unserviceable top of table centre in any position and S&F new table top made of 18mm thick MDF board exterior grade, lamination (teak Shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 30 Leg made out of 1st class hard teak wood 31 Top rail (shorter) made out of 1st class hard teak wood 32 Top rail (longer) made out of 1st class hard teak wood 33 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 34 PVC hard rubber shoe of approved quality 35 Bed Hard Plywood Top with MNF Set [Drg No : FD-21(M), FD-246] 36 S&F Top of bed plywoodmade out of 12mm thick, 7 ply, grade BWR, type BB commercial ply (IS-303) including taking downold one complete all as specified and as directed. Make Archidply/Century Ply/ Green Ply 37 S&F Head Board with legs made of teak wood covered with 4mm thick plywood 3 ply BWR grade, type BB, with decorative face veneers on one face or as per drawing. 38 S&F Foot Board with legs made of teak wood covered with 4mm thick plywood 3 ply grade BWR, type BB, with decorative face veneers on one face including taking down old one complete all as per drawing 39 S&F new teak ply of head board front and back of Bed hard including taking down old one complete all as per drawing 40 S&F new teak ply of foot board front and back of Bed hard including taking down old one complete all as per drawing 41 S&F Long rail made out of Ist Classhard wood (Teak wood) including taking down old one complete all as per drawing 42 S&F Stiffener made out ofIst Classhard wood (Teak wood) including taking down old one complete all as per drawing. 43 S&F new L shape MS clamp as per suitable size rest all as specified and directed by Engr-in-charge. 44 CharpoyGI pipe with ply top [Drg No : FD-220R/ CZ/TD/556] 45 Removing of old unserviceable ply top of charpoy GI pipe and S&F 12mm thick 7 ply BWR gde type BBsecuring with 6mm dia round headcountersunkbolts and nutswith washer (08 Nos) as per existing shape and size complete all as specified and as directed. 46 S&F Long Railmade of 32 mm bore (medium grade) galvanised iron pipe of CharpoyGI pipe complete 47 Labour only Short rail, made of32 mm bore galvanised iron pipe (medium grade) of Charpoy GIpipe (retrieved against item No. 7.02 above) complete 48 Labour onlyLegs, made of 32 mm bore galvanised iron pipe (medium grade) of Charpoy GI (retrieved against item No. 7.03 above), with and including 3 mm thick mild steel square plate, welded to bottom of legs, projecting 5 mm peripherally outer dia of leg and provision clamps for MNF set, as per drawing and specification complete 49 S&F32 mm bore galvanised iron three-way elbow (ISI marked) of Charpoy GIincl taking down existing elbow complete 50 S&F32 mm bore galvanised iron check nut of Charpoy GI pipe incl taking down existing check nut complete. 51 Removing old unserviceable / broken stiffener through grindig or cutting and S&F new 20mm GI pipe and welded the same properly with long rail. 52 Welding to broken stiffener of charpoy GI and pipe grinded for evenandsmooth gas welding afterpropertightening the complete frame complete all as specified and as directed. (Note : Welding of each broken joints shall be counted as one point.) 53 Chair Writing [Drg No :FD-280, 250, 20(M]Removing following unserviceable components from chair writing and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 54 Front leg made out of 1st class hard wood (teak) 55 Rear leg made out of 1st class hard wood (teak) 56 Side rail made out of 1st class hard wood (teak) 57 Rear rail made out of 1st class hard wood (teak) 58 Front Rail made out of 1st class hard wood (teak) 59 Armsmade out of 1st class hard wood (teak) 60 Stiffener made out of 1st class hard wood (teak) 61 Back rest made out of 1st class hard wood (teak) 62 PVC hard rubber shoe of approved quality 63 Chair Dining FD [Drg No :FD-279/1105, 250, 20(M)]Removing following unserviceable components from chair dining and supply and fix new components as per the following and fixing the same without disturbing the other partscomplete wherever shown on drawing and making functional the furniture as per drg and specification :- 64 Rear leg made out of 1st class hard wood (teak) 65 Front leg made out of 1st class hard wood (teak) 66 Side rail made out of 1st class hard wood (teak) 67 Front Rail made out of 1st class hard wood (teak) 68 Rear rail made out of 1st class hard wood (teak) 69 Back rest made out of 1st class hard wood (teak) 70 Stiffener made out of 1st class hard wood (teak) 71 PVC hard rubber shoe of approved quality 72 Chair Easy [Drg No : FD-17 (M), 229, 1108]Removing following unserviceable components from chair easy and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 73 Front leg made out of 1st class hard wood (teak) 74 Rear leg made out of 1st class hard wood (teak) 75 Front/back rail made out of 1st class hard wood (teak) 76 Side rail made out of 1st class hard wood (teak) 77 Arms made out of 1st class hard wood (teak) 78 Rail of seat frame made out of 1st class hard wood (teak) 79 Rail of back rest frame made out of 1st class hard wood (teak) 80 PVC hard rubber shoe of approved quality 81 Teapoy FD [Drg No : FD-278, 232, 34(M, 382]Removing following unserviceable components from Teapoy and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification : 82 M&L removal of unserviceable top of teapoy in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade) extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 83 Leg made out of 1st class hard wood (teak) 84 Top rail (shorter) made out of 1st class hard wood (teak) 85 Top rail (longer) made out of 1st class hard wood (teak) 86 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 87 PVC hard rubber shoe of approved quality 88 Table Writing [Drawing No : FD-27, 249, 33M, 275]Removing following unserviceable components from Table writing and supply and fix new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 89 long railmade out of 1st class hard wood (teak) 90 short railmade out of 1st class hard wood (teak) 91 Leg made out of 1st class hard wood (teak) 92 complete Box of the table including shelf, left /right side, back ply made out of18mm thick MDF exterior grade, lamination (teak shade) 93 Stiffenermade out of 1st class hard wood (teak) 94 Box back ply 6mm thick 3 ply commercial plywood conforming to IS-303 type BB duly polished 95 Front shutter made out of 18mm thick MDF exterior grade, lamination (teak shade) duly polished. 96 M&L removal of unserviceable top of table writing in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade) extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 97 Drawer made of teak wood with 6mm thick 3 ply commercial plywood conforming to IS 303 type BB shall be provided bottom of drawer dulypolished 98 steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw. 99 Table 1200x900x760mm [Drg No : FD-224, 283, / FD/MAP-II/03]Removing following unserviceable components from Table 1200x900x760mmand S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 100 M&L removal of unserviceable top of table 1200x900x760mm in any position and S&F new table top made of 18mm thick MDF exterior grade, lamination (teak shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 101 Legs made out of 1st class hard wood (teak) 102 Long side rail made out of 1st class hard wood (teak) 103 Short Side rail made out of 1st class hard wood (teak) 104 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 105 PVC hard rubber shoe of approved quality 106 Table 900x600x760mm with/without drawer[Drg No : FD-41, 42, 241, 223, 224, 283, 284]Removing following unserviceable components from Table 900x600x760mm with/without drawer and S&F new components as per the following and fixing in position all as specified and directed by Engr-in-Charge. 107 M&L removal of unserviceable top of table in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 108 Leg made out of 1st class hard wood (teak) 109 Long side rail made out of 1st class hard wood (teak) 110 Short side rail made out of 1st class hard wood (teak) 111 Drawer made of teak wood and 6mm thick 3 ply commercial plywood conforming to IS 303 type BB shall be provided bottom of drawer duly Frenck polished. 112 steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw. 113 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 114 PVC hard rubber shoe of approved quality 115 Table 900x900x760mm [Drg No : FD-224, 283]Removing following unserviceable components from Table 900x900x760mmand S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 116 M&L removal of unserviceable top of table in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 117 Legs made out of 1st class hard wood (teak) 118 Side rail made out of 1st class hard wood (teak) 119 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 120 PVC hard rubber shoe of approved quality 121 Table dining 6 Persons [Drg No : FD-239, 273,FD/MAP-II/03]Removing following unserviceable components from Table Dining 6 Personsand S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification :- 122 M&L removal of unserviceable top of table dining 6 persons in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 123 Leg made out of 1st class hard wood (teak) 124 Long side rail made out of 1st class hard wood (teak) 125 Short side rail made out of 1st class hard wood (teak) 126 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 127 PVC hard rubber shoe of approved quality 128 Table dining 8 Persons [Drg No : FD-239, 273, FD/MAP-II/03]Removing following unserviceable components from Table Dining 8 Personsand S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification. 129 M&L removal of unserviceable top of table dining 8 persons in any position and S&F new table topmade of 18mm thick MDF exterior grade, lamination (teak shade)with teak wood beading extended upto minimum 50mm from the bottom edge fixed in position all as specified and directed by Engr-in-Charge. 130 Leg made out of 1st class hard wood (teak) 131 Long side rail made out of 1st class hard wood (teak) 132 Short side rail made out of 1st class hard wood (teak) 133 S & F Ist class Teak woodbracket as per suitable size triangular( 08 Nos in a table) fixed with screws. complete all as specified. 134 PVC hard rubber shoe of approved quality 135 TABLE DRESSING LADIES WITH MIRROR [Drawing No: FD-378 & FD/MAP-II/07]Removing following unserviceable components from Table Dressing Ladies and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification:- 136 Drawers 137 Top made out of 18 mm thick Prelaminated MDF Board with teak wood beading 138 Bottom made out of 12 mm thick teak ply one side 139 Side frame of 18 mm thick MDF Board and back base of ply 6 mm teak face 140 Mirror of 5 mm thickness 141 Steel Knob round (as per sample) recessed 38mm dia fixed with 20mm screw. 142 TABLE DRESSING GENTS WITH MIRROR (FD-230)Removing following unserviceable components from Table Dressing gents and S&F new components as per the following and fixing the same without disturbing the other parts complete wherever shown on drawing and making functional the furniture as per drg and specification:- 143 New top of MDF Board 18mm thick and with Ist class seasoned teak wood beading 4mm thick all around including polishing to beadingmade to shape all as shown on drawing. Specified and directed by the Engr-in-Charge. 144 S&F in replacement of side with new side of 18 mm thick pre laminated MDF Board,exterior grade and including 4mm thick teak wood beading all-rounded. 145 All as per item No 19.01 but replacement of bottom with S&F new18 mm thick pre laminated MDF Board,exterior grade. 146 All as per item No 19.01 but replacement of mirror of size 380 x 760 x 5.5mm thick with teak wood frame complete all as shown on drawing. 147 S&F in replacement of chromium plate knob 25 mm dia of best qualityand as approved by Engr-in-Charge. 148 Removing broken/unserviceable hanging clip and S&F new MS Hanging Clips as per suitable size and fix with screw rest all specified by Engr-in-charge. 149 TABLE BED SIDE [Drg No: FD-276 & FD-265]Removing following unserviceable components from Table Bedside and S&F new components as per the following and fixing the same without disturbing the other parts and making functional the furniture as per drawing and specification :- 150 Top with 18mm thick pre-laminated MDF board exterior grade one side natural teak faced including teak wood beading on the top. 151 Side with 18mm thick pre-laminated MDF board exterior grade one side natural teak faced including teak wood beading around the side 152 Partition shelf made of 18mm thick pre-laminated MDF board 153 Back of 6mm thick ply wood commercial BWR with required size of screw all as specified and as directed by Engr-in-Charge. 154 Removal of existing polish from wooden surfaces of under mentioned articles of wooden furniture, cleaning the sameusing sand paper, smoothing properly without leaving any untouched wooden surfaces and polishing the same with two or more coats of French polish of appropriate shade, as approved / directed by the Engineer-in-Charge :- 155 Hat Stand with Mirror [Drg No : FD-233/361/362] 156 Bed ply wood top [Drg No: FD-21(M) , FD-246] 157 Peg Table [DrawingNo : FD-25, 227, 277, 236 & 384] 158 Table centre[Drg No: FD-29M, FD-235 & FD-274] 159 Table writing [Drg No: FD-33(M) & 275] 160 Table dressing ladies with mirror [Drawing No: FD-378 & FD/MAP-II/07] 161 Table dressing gents with mirror [Drawing No FD-230] 162 Table bed side FD-276 163 Table 1200 x 900 x 760mm Drg No -291, FD/MAP-II/03 164 Table900x900x760 mm wooden [Drg No : FD-88(M) &DB-3955] 165 Table 900x600x760mm with/without drawer [Drg No : FD-55(M),42(M) & 284] 166 Teapoy [Drg No : FD-34(M), DB-3975, FD-234 & FD-278, FD-382] 167 Table dining 8 persons [Drg No :FD-30(M), 239 &273, FD/MAP-II/03] 168 Table dining 6 Persons [Drg No: FD-30(M), 239 & 273, FD/MAP-II/03] 169 Chair Dining[Drg No: FD-16(M), 228 & 279, 1105] 170 Chair Easy [Drg No: FD-FD-17(M) & 229] 171 Chair Writing [Drg No: FD-20(M), 250 & 280] 172 Book case FD wooden 173 Recaning of Verandha Chair [Drg No FD-199M), 156(M) & 256] 174 Removing of old/worn out cane plastic of chair verandha recanning with new 4mm wide half round cane plastic white in colour (non recycled) made of superior qualityplastic rest all as per drawing /directed by Engineer-in-Charge. 175 Repairs to broken mild steel componentsof chair verandah with gas welding, including replacing broken /worn out legs with new 20mm dia MS pipe1.6mmthick 75mm to 100 mm long 176 S&F PVC rubber shoe/Toe of best quality after removing the old unserviceable shoe all as specified and directed. 177 Removing of old paint of chair verandha by using paint remover, emery papers etc, and providing two coats of synthetic enamel paint (First quality) as approvedcoloured on chair frame complete all as per drawing /directed by Engineer-in-Charge. 178 Recaning of different type of chair and furniture[Drg No: FD-15, 228, 279, 280, 150, 252, 27, 76(M) & FD-2]Removing of old/worn out cane plastic and recanning with 2mm wide half round cane plastic white of superior quality for seat and back (as applicable) and 3mm wide half round cane plastic on the borders locked in at 125mm intervals complete all as per drawing/directed by Engr-in-Charge :- 179 Chair Dining 180 Chair Easy 181 Chair writing
