|
| 1 | Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified andas directed. |
| 2 | M&LRendering15mmthickonfairfacesofbrick work or concrete surface in cement plaster 1:4 finishing the surface even & smooth without using extra cement & with WPC (WPC will be measured & paid seperately) complete all as specified & as directed. |
| 3 | SupplyonlyWPC.(IntegralWaterProofing Compound) complete all as specified & as directed.. |
| 4 | M&L for preparation of all type of surfaces and finishing walls with Premium Acrylic Smooth exterior paint (in camouflauge pattern) with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over new prepared surface complete all as specified and directed. . |
| 5 | M&L forapplyingprimer of same make(as of exterior weather proof water base emulsionpaint )onwhite cement based putty allas specified and directed. (Putty shall be measured and paid seperately under relevant Item) complete all as specified and directed |
| 6 | Preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spotsand stopping nails marks by filling with white cement base putty and applying two coat ofexterior weather proof water base emulsionpaint white/coloured. Make Asian- Apex or Equivalent |
| 7 | M & L for preparation of newly plastered/Putty surfaces of wallsand applying two coat exterior weather proof water base emulsionpaint white/coloured over a coat of primer same make baseall as specified and directed.Make Asian- Apex or Equivalent. Note:- Primer& Putty shall be measured and paid seperately under relevant Item |
| 8 | M&L for preparation of newly plaster surface of wall and and apply 2mm thick cement base wall care putty in two coat (each coat not less than 1mm) over a coat of primer on walls and surface finished even and smooth with sand paper completeall as specified and directed |
| 9 | M&L for removal of complete existing treatment of wall(any no. of layers) and apply 2mm thickwhite cement base wall care putty in two coats (each coat not less than 1mm) on wallsand surface finished even and smooth with sand paper completeall as specified and directed |
| 10 | M & L for preparation of newly plastered wall/ceilling surfaces and applying three coats of white wash complete all specified and directed. |
| 11 | M & L for preparation of old surface of wall/ceilling surfaces and applying three coats of white wash complete all specified and directed. |
| 12 | M&L for preparation of old concreate/PCC tile surfaces by brooming with coir/wire brushes and wahsing down with water to remove the fine dust and applying two coats of Lacquer polish (1001) chemical with pigment as approved complete all as specified and directed. |
| 13 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 14 | Dismantling stone slabs and tiles of any description or thickness in floors,aprons laid dry or laid dry and pointed complete all as specified and directed |
| 15 | M&LPCC(1:4:8)typeD-2(using40mmgraded stone aggregate) as in foundations, filling and mass concrete all as specified and as directed. |
| 16 | M&Lfor 80mm thick machine pressed precast concrete interlocking paver block (glossy finish) of M-35 Gde of approved shape, size and colourconferming to IS 15658-2006 andincluding joints filled with sandcomplete all as specified and as directed. |
| 17 | M&L for preparation of road surface and applying thermoplastic reflective paint for marking of minimum 1.5 mm thick single coat as a centre line or edge line etc, road marking of 150/100 mm width using \"HOT MARK\" thermo plastic paint (Hot application) white /yellow by indigenous modern propelled road marking machine as directed including all ingredients such as binder, glass beads, titanium dioxide, calcuim caronate, inter filler etc, thermoplastic requirement for glass beads shall be conforming to BS-6086 of MOST specificaiton including spraying of glass beads etc complete all as per manufacture\"s instructions and as directed. |
| 18 | M&L for Polyurethane Pavement Joint Sealant, sealed using Fosroc Colpor 200, pavement sealant manufactoured by Fosroc to BS 5212: 1990, Joint shall be prepared and the sealant mixed and applied as per the manufacturer\"s instruction complete all as directed by Engr in Charge. (Note- The Joints require the complete removal of all foregin materials, including old sealant, dirt, and debris to ensure proper adhesion of new joint sealants.) |
