|
| 1 | Excavation in trenches not exc 1.5m wide and n.exc 1.5m in depth for foundations, manholes etc and getting out in hard / dense soil. |
| 2 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm |
| 3 | Removal excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete |
| 4 | Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided and inclusive of removal of debris out side defence land complete |
| 5 | M&L for cement concrete type D2 1:4:8 (using 40mm graded aggregates) in foundation, filling and mass concrete complete |
| 6 | M&L for TMT bar 10mm dia and over cut to length bent to shape reqd incl cranking bending etc complete & binding with MS wire (annealed) not less than 0.9mm dia in reinforcement complete |
| 7 | All as per item No 6 (here in before) but 8 to 10mm dia as in stirrups complete |
| 8 | M&L for formwork to rough finished flat surfaces of footing and plinth beams complete |
| 9 | M&L for formwork to rough finished flat surfaces of pillars, posts, struts, piers, columns and stanchions etc complete |
| 10 | M&L for formwork to chajja, roof beams, lintels and soffits of roof projections etc and similar items including edges |
| 11 | M&L for reinforced cement concrete nominal mix B1 1:2:4 (using 20mm graded aggregate) for foundations, including rafts, footings, plinth beams, bases for columns, etc complete |
| 12 | M&L for reinforced cement concrete nominal mix B1 1:2:4 (using 20mm graded aggregate) forcolumns, pillars, piers, posts and struts etc complete |
| 13 | M&L for reinforced cement concrete nominal mix B1 1:2:4 (using 20mm graded aggregate) forroof beams and lintels complete |
| 14 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided and removal of debris out side defence land complete |
| 15 | M&L for precast cement concrete block masonry exceeding 10cm in width witth solid blocks of PCC (1:5:8) gde D-5 and setting in CM 1:6 |
| 16 | M&L PCC (1:2:4) type B-1 using 20 mm stone graded aggregate as in cills, steps, bands, plinth courses, string courses, lacing courses, coping kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles etc complete. |
| 17 | Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete. |
| 18 | M&L for 15 mmthick rendering in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 19 | M & L preparation of newly plastered wall surface of any description girth and applying two or more coats of acrylic smooth exterior paint of required shade as in new work (two or more coat applied @ 1.67 ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10sqm ) in camouflage pattern complete all as specified and directed |
| 20 | M & L for preparation of old wall surfaces of any description and applying one coat of acrylic smooth exterior paint of required shade in camouflage pattern including filling of depression with exterior grade wall putty complete all as specified and directed |
| 21 | S & F in repair Steel rolling shutters, withball bearing and Safety lever locks mild steel with 4 levers, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, complete: push pull or manual type complete all as specified and directed |
| 22 | Supply and stacking new HDPE bags with laminated layer, white coloured empty bags shall not be less than 90gm per bag and filled with locally available saw dust / sandin CM 1:3 approximate quantity 25 kg in each bag, tying properly and stacking neatly at site, in pyramid, circle or any other geometrical shape and for any height including removing old worn out, unserviceable bags (filled with saw dust / sand) fr4om the stack completely and levelling the area as directed and preparation of surface for further stacking all as specified and as directed by Engineer-in-charge complete |
| 23 | M&L for loosening of any type of soil to average depth 40-50 cm by removing the stone, metal pieces of size exc 50mm and depositing to a distance exc 150m but n.exc 200 m from FG target area including levelling surfaces after loosening the earth by mechanical earth movers or tractors or any other devices all as specified and as directed by the engineer-in-charge complete |
| 24 | M&L for loosening of any type of soil to average depth 20-25 cm by removing the stone, metal pieces of size exc 50mm and depositing to a distance exc 150m but n.exc 200 m from PTB, LBT target area including levelling surfaces after loosening the earth by mechanical earth movers or tractors or any other devices all as specified and as directed by the engineer-in-charge complete |
| 25 | Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified. . |
| 26 | S&F MS framed work such as grills, door or gates with orramentaled intricate design gratings. Etc., with ends of bars shouldered and/or rivetted, or forged into spikes framed guard bars barred iron doors, ladders, railings & similar works conforming to Fe-410-0 or 310-0 complete all as specified. |
| 27 | M & L preparation of steel and iron surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified. . |
| 28 | M&L for cement concrete type C-2 (1:3:6) 75 mm thick as in plinth protection surface fair & even.complete all as specified and directed. |
| 29 | M&L for 75 mm PCC 1:4:8 type D-2(using 40 mm stone aggregate) as in sub base to floors for laying tiles floorscomplete allas specified and directed. |
| 30 | M&L for coloured, glossy finish Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry and painted in white or coloured cement in floorsincl 15mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 31 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive way or light traffic, parking etc of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping etra and complete all as specified and directed |
| 32 | M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive way or light traffic, parking etc of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping etra and complete all as specified and directed |
| 33 | M&L for 100mm thick PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in hard standing laid in alternate bays including necessary form work complete all as specified and directed |
| 34 | M&L forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete |
| 35 | Taking down hangar shutter of area exc 60 Sqm n exc 80 sqm area of any description and removing all bends, dents, replacing rollers with new rollers at top and bottom of shutter, bolting and riveting the existing mild steel sheet with steel framing made for shutters including necessary welding wherever required at places and making good the shutters to true functional for easy movement of shutter on rail by manually pushing and pulling and erected to original position complete all as specified and directed. (Sheet for gate will be paid separately) |
| 36 | Dismantling fencing of any type fixed in any situation including flat iron MS round bars, mounted on nuts & bolts etc complete all as specified. |
| 37 | Dismantling wrought iron or mild steel work of any description not otherwise provided for and concertina coil complete all as specified and directed . |
| 38 | Excavating in posts holes (or similar holes) in soft and loosesoil each n.exc 0.50 cu.m getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm. |
| 39 | Dismantling RCC post or strutembeded in concrete any section including takingout embeded portion and making good distrubed ground. |
| 40 | M/L for providing PCC 1:3:6 type C2 using (40mm graded stone aggregate) in foundation filling and mass concrete. |
| 41 | Supply and fix mild steel angle iron or other stock section posts and struts in fencing, Purlin/Rafter/ Truss including cutting tops to shape as directed drilling holes, welding, notching for wire, incl flat iron fillets (for securing wire meshetc) including all necessary drilling bolting orriveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 42 | M&L for providingtype B-l, 1:2:4 (20 mm graded aggregate) in Precast RCC fencing posts, straining or teriminal posts, struts, etc. for fencing, average sectional area exc.100 but n.exc. 250 Sq cm complete all as specified and directed |
| 43 | M&L for Mild steel TMT bars 10mm dia and over cut to length ,bent to shape required,including crancking, bending soirally for hooping for cols, hooking ends and binding with mild steel wire annealed not less than 0.9mm dia |
| 44 | M&L for Mild steel TMT bars 5mm and over upto 10mmdia cut to length,bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9m dia or securing with clips |
| 45 | Supply only, chain link fencing of MS galvanized fencing, any size or type. |
| 46 | Fixing only old or newly procured chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separetly. |
| 47 | S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt exc 5cm but n.exc 10cm long and dia of neck 11 to 15mm complete all as specified and as directed |
| 48 | M&L Mild steel round bars, 10mm dia cut to length weared and securing chain link fencing to fencing posts, complete all as specified and as directed |
| 49 | M&L for preparation of new steel surfaces and apply two coats ofsynthetic enamel paint over a coat of red oxide primer over 10 cm in width or girth of surfaces complete all as specified and directed. |
| 50 | M&L for preparation of new steel surfaces and apply two coats ofsynthetic enamel paint over a coat of red oxide primer over n exc10 cm in width or girth of surfaces complete all as specified and directed. |
| 51 | Preparation ofold painted concrete/plaster surfaces of any description andin any position over 10cm width of girth andM&L for applying twocoat of ready mixedpaint complete all as specified and directed. |
| 52 | S&Fin repair galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including, securing and tying at crossings with and provisions of galvanised mild steel wire staples or steel pins etc as directed (each line wire to be measured). |
| 53 | Supply only concertina coil razor type in 06 coil in stretch of 1.0m length for fencing work,straining and fixing to angle iron/barbed wire with and including necessary clips for each bundle of coil) for securing complete all as specified and directed. |
| 54 | Fixing in repair concertina coil razor type in 06 coil in stretch of 1.0m length for fencing work,straining and fixing to angle iron/barbed wire with and including necessary clips for each bundle of coil) for securing complete all as specified and directed. |
| 55 | Dismantling asbesots cement (corrugated, semi-corrugated etc) sheets in roof coverings Complete all as specified and directed. |
| 56 | Dismantling timber scantling 40 Sqcm and over in section, in any position of framed work completeall as directed |
| 57 | M&L forIInd class hardwood in scantling timber framed and fixedwrought in any position and in any situation complete all as specified and as directed. |
| 58 | S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick ofcolour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or \"J\" /\"L\"hooks all as specified and directed. |
| 59 | Ditto as in item No. 9 but plain sheet as in ridges, gutters , facia etc complete all as specified and directed |
| 60 | M&L for preparation of new steel surfaces of any description and in any position/over any height, exc 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer in camouflage patter complete all as specified and as directed. |
