|
| 1 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 2 | In cement mortar |
| 3 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 4 | 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Centering and shuttering including strutting, propping etc. and emoval of form work for : |
| 6 | Foundations, footings, bases of columns, etc. for mass concrete |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 8 | Thermo-Mechanically Treated bars |
| 9 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 10 | Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 11 | Hot finished welded type tubes |
| 12 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 14 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 15 | 20 mm cement plaster of mix : |
| 16 | 1:6 (1 cement: 6 coarse sand) |
| 17 | 12 mm cement plaster of mix : |
| 18 | 1:6 (1 cement: 6 coarse sand) |
| 19 | Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. |
| 20 | Beyond 60 cm girth up to and including 120 cm girth |
| 21 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 22 | New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 23 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 24 | Beyond 120 cm girth upto and including 240 cm girth |
| 25 | Cleaning the unplastered brick wall surface and removing dirt, dust, oil, algae, fungus, vegetable growth etc., including providing, applying and presure jet washing with wateras approved byEngineer-in-charge. |
| 26 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): |
| 27 | From brick work in cement mortar |
| 28 | Brick work with avalble bricks in Cement mortar 1:6 (1 Cement :6 Coarse sand) for foundation and plinth |
