Tender For Construction Of Shelter Home At Pindwara ., Pindwara-Rajasthan

TDR : 52229872

Tender Notice
BOQ

Expired

Pindwara , Rajasthan

Tender Brief : Tender For Construction Of Shelter Home At Pindwara .

Document Fees
₹ 5000 /-

EMD
₹ 300000.0 /-

Tender Value
₹ 1.50 Crore /-

Submission Date
28-11-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 1.5 m
2	Filling with locally available river sand at all levels including watering ramming consolidating and dressing complete including cost of sand. 100 mm Thick in foundation
3	Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m.
4	Carriage of Materials by mechanical transport including loading, unloading and stacking : Earth (Rate for lead 5 km.)
5	Supplying Chlorpyriphos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified.
6	Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinthlevel : 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). PCC
7	Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.
8	Columns, Pillars, Piers, Abutments, Posts and Struts up to plinth level
9	Lintels, beams, plinth beams, girders, bressumers and cantilevers.
10	Suspended floors, roofs, landings, balconies and access platform
11	Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Hot rolled deformed bars
12	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size). (As per design mix) All work upto plinth level :
13	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto two stories excluding cost of centring, shuttering, finishing and reinforcement : 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) (As per design mix)
14	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto two stories excluding the cost of centring, shuttering, finishing and reinforcement: including Providing /mixing of synthetic fiberscompulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar .M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 gradedstone aggregate 20 mm nominal size) -As per design mix)
15	Random rubble stone masonry with hard stone in foundation and plinth : Cement mortar 1:6 (1 cement : 6 coarse sand)
16	Random rubble dry stone Kharanja (soling) under floor.
17	Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). Under flooring PCC
18	Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)
19	Half brick masonry with FPS bricks of class designation 75 in superstructure above plinth level upto two stories. Cement mortar 1:4 (1 cement :4 coarse sand)
20	Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand)
21	Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand) Ceilling plaster
22	P & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in colour, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete.Size 450 mm X 450 mm
23	Providing and fixing 1st quality MAT & GLOSSY finished ceramic tiles colour such as standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorbtion less than or equal to 0.08% confirming to IS : 13753 & IS : 15622 in floor, steps etc laid on bed on neat cement slury finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the the cost of cement mortar bed 1:4) Size 300mm x 450mm
24	Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete Birla/J.K./Nerolac or ISO. As per direction of Engineer in charge. All walls Inner side
25	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shad. New work (two or more coats) over and including priming coat with cement primer.
26	Kota stone slab flooring 25mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed withpigment to match the shade of the slab including rubbing andpolishing complete with base of cement mortar 1 : 4 (1 cement : 4coarse sand) : Area of each slab 2001 to 5000 sqcm
27	Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. (Upto to 1500 Cm2 Tiles)
28	Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
29	Kota stone slabs 25 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
30	Providing and fixing stainless steel ( Grade 304) Railing made ofHollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) andfitting the same with necessary stainless steel nuts and boltscomplete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitablearrangement as per approval of Engineer-in-charge, (for paymentpurpose only weight of stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts, fasteners etc.).
31	Steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. Hot finished welded type tubes
32	Water proof plyboard 12mm thick.
33	Providing and fixing M.S. Tubular frames for doors, windows,ventilators and cupboard with L-Type section made of 1.60mm thick M.S. Sheet, joints mitred and welded and grinded finish profiles required size with 15x3mm lugs 10cm long embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primers.
34	26.22 Providing and fixing double paitam (rebated) stone doors windows and ventilator frames of approved quality in cement sand mortar 1:4: (Size 125 X 100 MM)
35	Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.
36	Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows.
37	Providing and fixing GI wire gauge of average width of aperture 1.56mm with wire of 0.45mm to existing steel door, window shutter frames with necessary M.S. strip beading 20x3mm with suitable screw at not exceeding 150mm distance etc. complete.
38	24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ± 0.1 mm wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and directionof Engineer-in-charge. (For W.C. and bathroom door shutter).
39	Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formaldehyde resin in glue both sides including approved ISI marked Stainless Steel butt hinges fittings with necessary screws complete as per annexure \"A\" : 35 mm thick Decorative teak veneer both side
40	Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled ISI marked M.S butt hinges with necessary screws. Second class teak wood 35 mm thick
41	Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.
42	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) :Polyester powder coated aluminium (minimum thickness of polyesterpowder coating 50 micron) For Main gate Parrallae of Chainal gate
43	Providing and fixing glazing in aluminium door, window, ventilatorshutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basic item) :With float glass panes of 8 mm thickness
44	Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate
45	Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar
46	Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete.
47	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures omplete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
48	Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan of size 580x440 mm
49	Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white
50	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet. Sand cast iron S&S as per IS: 3989.
51	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers.
52	Providing and fixing 600x450 mm bevelled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete.
53	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.
54	P.T.M.T. Soap Dish/Holder 138x102x75mm
55	Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450 U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc. with clamps at 1.00 metre spacing. this includes testing of joints complete as per direction of the Engineer in charge. Internal work - Exposed on wall 1216 (16 mm OD) pipe
56	Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450 U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc. with clamps at 1.00 metre spacing. this includes testing of joints complete as per direction of the Engineer in charge. Internal work - Exposed on wall 2025 (25 mm OD) pipe
57	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore.
58	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore
59	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore
60	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (500 Lite X 4 Nos)
61	Constructing masonry Chamber 60x45x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With F.P.S. bricks
62	Construction of Septic Tank in all types of soil with 40 Cm. thick masonry in CM 1 : 6, 15 Cm. thick C.C. bed of 1 : 5 : 10, M-15 grade C.C. flooring & over stone slab covering, 80 mm thick slab, jointing of slab in CM 1 : 3 Ralthal, Kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in CM 1 : 6 finished with neat floating cement, 4 Nos C.I. foot rests of approved design, two No. 450 mm dia 25 Kg. of each C.I. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 Mtr. Size 400 x 140 x 150 cm (for 50 users)
63	Providing and fixing on wall face Unplasticised Rigid PVC Singlesocketed pipes rain water pipes conforming to IS : 13592 Type Aincluding jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. 75 mm diameter
64	Providing and fixing on wall face Unplasticised Rigid PVC Singlesocketed pipes rain water pipes conforming to IS : 13592 Type Aincluding jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. 110 mm diameter
65	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Coupler (Socket) 75 mm dia
66	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Coupler (Socket) 110 mm dia
67	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant.Single tee without door 75x75x75 mm
68	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant.Single tee without door 75x75x75 mm
69	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Bend 87.5° 75 mm bend
70	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Bend 87.5° 110 mm bend
71	Providing and fixing Unplasticised -PVC pipe clips of approveddesign to Unplasticised - PVC rain water pipes by means of50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing in cementmortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm
72	Providing and fixing Unplasticised -PVC pipe clips of approveddesign to Unplasticised - PVC rain water pipes by means of50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing in cementmortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
73	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250mm.
74	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively.
75	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Short point (up to 3 mtr.)
76	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Medium point (up to 6 mtr.)
77	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Long point (up to 10 mtr..)
78	Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Single pole MCB 6 A to 32 A rating
79	Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Double pole MCB 6 A to 32 A rating
80	Providing & Fixing of 240/415 V Residual current circuit breaker(RCCB) as per PWD specification for electrical Works with ISImarked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Two pole 30 mA sensitivity 16/25 A rating
81	Providing & Fixing of 240/415 V Residual current circuit breaker(RCCB) as per PWD specification for electrical Works with ISImarked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 32/40 A rating
82	Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel not less then 1.2 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating nsulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . IP-43 Double door (single phase) ,6 Way (6 O/G +2 I/C )
83	Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel not less then 1.2 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating nsulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . IP-43 Double door (Three phase) , 4 Way ( 12 O/G + 8 I/C )
84	Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceiling roses as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABSmaterial, brass terminal & captive screws including makingconnection testing etc. as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
85	Providing & Fixing of ISI marked (IS:1258) 6 amp batten/anglelamp holder as per PWD specification for electrical Works, madeout from industrial grade Polycarbonate or fire resistant ABSmaterial, brass terminal & captive screws including makingconnection testing etc. as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR .
86	Providing & Fixing of energy efficient /energy saving IP 20 LEDdirect retrofit Bulb in existing holder or fixture as required withsystem lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screenprinting on housing. OEM must have its own in house NABL labsetup for all testing facilities for LED fixtures. (LM79/LM80)certificate / Report from OEM shall be submitted. All as per preapproved by engineer in-charge . for additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR. 15 Watt
87	Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured / Armoured copper cable of 1.1 KV grade as per PWDspecification for electrical Works in existing RCC / Hume /Stoneware / PVC pipe/ open duct/cable trench with filling ofexcavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Copper conductor of electrlytic grade copper, purity >99.97 %ISI marked as per IS:1554 P-I / IS :7098 P - I(b) conductor shall made of copper rods confirming to IS 613-1964, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures (c) OEM Must have ISO 9001 & 14001 certifications & its own in house NABL lab setup for all testing facilities for cables .Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
88	P/Laying ISI marked P.V.C. insulated submersible cable confirmingto IS:694 with flexible copper conductor including making connectionetc. as required \"6 Sq.mm 3 core flat/ROUND
89	Plate Earthing as per PWD specification for electrical Works as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. \"B\" class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
90	Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu thimble etc. as required. All as perpre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR . 6 SWG copper Wire
91	Providing & Fixing of copper tape 20mm x 3 mm on parapet orsurface of wall fixed with porcelain or bakelite insulator (SP-35) invertical/horizontal run as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR , 20mm x 3mm copper strip
92	Providing & Fixing of IP20 SMD Mid Power LED batten typeintegrated light fixture made from polycarbonate /extrudedaluminium powder coated housing with in built driver , PowerConsumption of 18W/20W ,system lumen efficacy ≥ 120 lm/Wattoutput, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR. 4\" LED Tube shape fixture 18/20 W (Extruded Al Base)
93	Providing & Fixing of Heavy duty capacitor start, copper woindDouble ball bearing 900/1400 RPM single phase Exhaust fan asper PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 300 mm sweep(900/1400 RPM)
94	Providing & Fixing of ISO Certified company made BEE Approved copper wounded 1200 mm sweep BLDC technology power saving ceiling fan with longer life span and low maintenance 5 star rated which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not less then 0.9 , service value (CMM/W) minimun 6.85 , air delivery minimun 215 CMM, speed 350 RPM (tolerance as per IS:374 2019 ) THD less then 10% and complete with down rod up to 30 cm with secondary support safety cable , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper onductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .Without Remote
95	Providing and fixing of non modular power plug point accessoriesas per PWD specification for electrical Works with 18 SWG G I box of size 175 x 100 x 60 mm with earthing terminal/connector on recessed/surface with suitable size phenolic laminated sheet (IS :2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet [ as per detailed in respective item in BSR], making connection , testing , etc. as required. All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR .
96	SITC of Radial / mixed flow ISI marked water and anti-corrosiveliquid filled submersible motor pump sets suitable for 100/150mmdia borewell. The size of adopter fixed on top of the motor shouldexceed the top of coupler , for safegaurd the coupler. Theconstruction material of motor and pump should match IS: 8034 :2018 and IS: 9283 guideline. The radial flow pumpset shouldoperate at 5 star energy efficiency level of BEE and mixed flowpump set should operate at 3 star energy level of BEE,accompained by valid BEE certificate. Motor should be IE2 class asper IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011with required accessories including making connection suitable forBore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM Copper Wound
97	Supply and erection of Galvanized Iron pole with galvanizing donein single dipping (Average coating thickness Minimum 65 Microns)Swaged tubular pole conforming to IS: 2713-1980 (part I to II) with galvanised base plate, The pole shall be made from steel tube & Pipe (IS:1141, Fe 410) including excavation of the pit and filling the same with C.C. of M-20 grade (1:1.5:3) from base plate to 50 cm above ground level, with the help of steel frame not less than 40 cm dia up to 114.3mm outer dia and 50 cm beyond 114.3mm outer dia around the pole. Duly finished with cement plaster, earthing terminals, cable entry with 32 mm dia. \"B\" class GI cable sleeves complete as required. of following height & designation. ( See Table P - 02 for specs. ) All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .7.5 Mtr. ( 410 SP - 5 )
98	Providing & Fixing of IK07 IP-66 protected high power LED floodlight system with Pressure diecast aluminium housing LM6/ ADC12material , toughened glass diffuser with suitable lenses on LED toachieve various beam angles, 240 volt, 50Hz, of high power LEDlamps . Integrated driver must be potted & has a unique BIS numbershall be high efficiency having efficiency more than 85 % and incompliance to BIS certified and T.C. certificate. The System levelLuminaire efficacy >=120 lm/ wt with High Power LEDs is to be used . LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety . Input Frequency 50Hz±3%, Power Factor >0.95 ,driver Efficiency >85% , THD(I) <10% , driver current <1000mA shown in LM79 report. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector Must be provided, Surge Protection Min >=4KV internal and 10KV external, System life of 30000 Burning hours with 70% of Initial Lumens maintained, color Rendering Index >70 and CCT 5700K ±355K. Driver current <1000mA shown in LM79 report. Fixture shall be IS 10322 Compliant. All as per pre approved by Engineer in-charge. High Power LED Flood Light 30W
99	Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR. 10sqnn 2 core
100	P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR. 50 mm
101	Construction of Tube-well upto 100 Meter depth and above in alltype of rocks by DTH system and over burden to accommodatecasing pipe of following sizes in all types of soils and over burdenincluding lowering of casing pipes but excluding cost of casing pipesas per IS : 2800 (Part I & II) 1979 specifications. The work would be completed after obtaining sand free water. The tube well shouldhave a throughout bore as per nominal dia of casing pipe:200 mm dia Nominal bore
102	Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/1992) of grade Fe410 of following nominal bore sizes at site of work.125 mm dia
103	Supply and fixing of tube well cover of M.S. sheet (6mm thick) with nuts and bolts complete for casing size:125 mm dia
104	Supply and fixing of M.S. clamp set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersiblepump set.
105	Installation of submersible motor pump set in tube-well/open well complete (labour charges only) including transportation of tripod, chain pulley block & any other material required for lowering purpose.
106	Providing & lowering of G.I. flange pipe B Class including rubberwasher and nuts of 8 mm dia complete in all respect . 75 mm dia
107	Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. Lintels, beams, plinth beams, girders, bressumers and cantilevers. Column up to roof beam C1 2 X( L+B) X H
108	Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete. Suspended floors, roofs, landings, balconies and access platform
109	Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Hot rolled deformed bars
110	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto two stories excluding cost of centring, shuttering, finishing and reinforcement : 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) (As per design mix)
111	Reinforced cement concrete work in beams, suspended floors,roofs having slope upto 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair casesupto two stories excluding the cost of centring, shuttering, finishingand reinforcement: including Providing /mixing of synthetic fiberscompulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar .M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 gradedstone aggregate 20 mm nominal size) -As per design mix)
112	Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)
113	Half brick masonry with FPS bricks of class designation 75 in superstructure above plinth level upto two stories. Cement mortar 1:4 (1 cement :4 coarse sand)
114	Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand)
115	Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand) Ceilling plaster
116	P & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in colour, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete. Size 450 mm X 450 mm
117	Providing and fixing 1st quality MAT & GLOSSY finished ceramic tiles colour such as standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorbtion less than or equal to 0.08% confirming to IS : 13753 & IS : 15622 in floor, steps etc laid on bed on neat cement slury finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the the cost of cement mortar bed 1:4) Size 300mm x 450mm
118	Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete Birla/J.K./Nerolac or ISO. As per direction of Engineer in charge. All walls Inner side
119	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shad. New work (two or more coats) over and including priming coat with cement primer.
120	Kota stone slab flooring 25mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed withpigment to match the shade of the slab including rubbing andpolishing complete with base of cement mortar 1 : 4 (1 cement : 4coarse sand) : Area of each slab 2001 to 5000 sqcm
121	Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. (Upto to 1500 Cm2 Tiles)
122	Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
123	Kota stone slabs 25 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3coarse sand) and jointed with grey cement slurry mixed with pigmentto match the shade of the slabs, including rubbing and polishingcomplete.
124	Providing and fixing stainless steel ( Grade 304) Railing made ofHollow tubes, channels, plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) andfitting the same with necessary stainless steel nuts and boltscomplete, i/c fixing the railing with necessary accessories & stainlesssteel dash fasteners , stainless steel bolts etc., of required size, onthe top of the floor or the side of waist slab with suitablearrangement as per approval of Engineer-in-charge, (for paymentpurpose only weight of stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts, fasteners etc.).
125	Steel work in built up tubular trusses including cutting, hoisting fixingin position and applying a priming coat of approved steel primer,welded and bolted including special shaped washers etc. complete. Hot finished welded type tubes For sleeping Bed Builtup in Room
126	Water proof plyboard 12mm thick. For sleeping Bed Top
127	Providing and fixing M.S. Tubular frames for doors, windows,ventilators and cupboard with L-Type section made of 1.60mm thickM.S. Sheet, joints mitred and welded and grinded finish profilesrequired size with 15x3mm lugs 10cm long embedded in cementconcrete blocks 15x10x10cm of 1:3:6 (1 cement : 3 coarse sand : 6graded stone aggregate 20mm nominal size) or with wooden plugsand screws or rawl plugs and screws or with fixing clips or with boltsand nuts as required including fixing of necessary butt hinges andscrews and applying a priming coat of approved steel primers.
128	26.22 Providing and fixing double paitam (rebated) stone doors windows and ventilator frames of approved quality in cement sand mortar 1:4: (Size 125 X 100 MM)
129	Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows.
130	Providing and fixing GI wire gauge of average width of aperture 1.56mm with wire of 0.45mm to existing steel door, window shutter frames with necessary M.S. strip beading 20x3mm with suitable screw at not exceeding 150mm distance etc. complete.
131	24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm ± 0.1 mm wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm ± 0.2 mm wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ± 0.1 mm wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and directionof Engineer-in-charge. (For W.C. and bathroom door shutter).
132	Providing and fixing external grade board solid core single leaf flushdoor shutters ISI 2202-67 marked using Phenol formaldehyde resinin glue both sides including approved ISI marked Stainless Steel butthinges fittings with necessary screws complete as per annexure \"A\" : 35 mm thick Decorative teak veneer both side
133	Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled ISI marked M.S butt hinges with necessary screws. Second class teak wood 35 mm thick
134	Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.
135	Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS : 1285, fixed with rawl plugs andscrews or with fixing clips, or with expansion hold fasteners includingnecessary filling up of gaps at junctions, at top, bottom and sideswith required PVC/neoprene felt etc. Aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminium snap beading for glazing /panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately) :Polyester powder coated aluminium (minimum thickness of polyesterpowder coating 50 micron) For Main gate Parrallae of Chainal gate
136	Providing and fixing glazing in aluminium door, window, ventilatorshutters and partitions etc. with PVC/ neoprene gasket etc. completeas per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basicitem) :With float glass panes of 8 mm thickness
137	Providing and fixing double action hydraulic floor spring of approvedbrand and manufacture IS : 6315 marked, for doors including cost ofcutting floors as required, embedding in floors and cover plates withbrass pivot and single piece M.S. sheet outer box with slide plateetc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate
138	Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc .complete as perdirection of Engineer-in-Charge.Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar
139	Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete.
140	Grading roof for water proofing treatment with water proofing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
141	Providing & laying broken glazed titles on roof (broken glazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg of VG-40 (30/40 )grade and 0.30 Kg/Sqm. Of VG-10(80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineerin-charge.
142	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase. Roof Tarrace Batta Gola
143	Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern with manually controlled device (handlelever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
144	Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan of size 580x440 mm
145	Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white
146	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet. Sand cast iron S&S as per IS: 3989.
147	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow operated levers.
148	Providing and fixing 600x450 mm bevelled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washerscomplete.
149	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms.
150	P.T.M.T. Soap Dish/Holder 138x102x75mm
151	Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450 U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc. with clamps at 1.00 metre spacing. this includes testing of joints complete as per direction of the Engineer in charge. Internal work - Exposed on wall 1216 (16 mm OD) pipe
152	Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450 U.V. stabilised with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc. with clamps at 1.00 metre spacing. this includes testing of joints complete as per direction of the Engineer in charge. Internal work - Exposed on wall 2025 (25 mm OD) pipe
153	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15 mm nominal bore.
154	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore
155	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore
156	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (500 Lite X 4 Nos)
157	Providing and fixing on wall face Unplasticised Rigid PVC Singlesocketed pipes rain water pipes conforming to IS : 13592 Type Aincluding jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. 75 mm diameter
158	Providing and fixing on wall face Unplasticised Rigid PVC Singlesocketed pipes rain water pipes conforming to IS : 13592 Type Aincluding jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. 110 mm diameter
159	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Coupler (Socket) 75 mm dia
160	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Coupler (Socket) 110 mm dia
161	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Single tee without door 75x75x75 mm
162	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Single tee without door 75x75x75 mm
163	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Bend 87.5° 75 mm bend
164	Providing and fixing rigid PVC Pipe fittings (IS : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. Bend 87.5° 110 mm bend
165	Providing and fixing Unplasticised -PVC pipe clips of approveddesign to Unplasticised - PVC rain water pipes by means of50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing in cementmortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm
166	Providing and fixing Unplasticised -PVC pipe clips of approveddesign to Unplasticised - PVC rain water pipes by means of50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing in cementmortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
167	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250mm.
168	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively.
169	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Short point (up to 3 mtr.)
170	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Medium point (up to 6 mtr.)
171	Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexiblecopper conductor 1.1 kV grade and 1.5 sq. mm nominal size FRPVC insulated unsheathed flexible copper earth conductor 1.1 kVgrade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Long point (up to 10 mtr..)
172	Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of lass 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technica parameters of products/ work , refer Annexure \"A\" attached withthis BSR . Single pole MCB 6 A to 32 A rating
173	Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Double pole MCB 6 A to 32 A rating
174	Providing & Fixing of 240/415 V Residual current circuit breaker(RCCB) as per PWD specification for electrical Works with ISImarked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . Two pole 30 mA sensitivity 16/25 A rating
175	Providing & Fixing of 240/415 V Residual current circuit breaker(RCCB) as per PWD specification for electrical Works with ISImarked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 32/40 A rating
176	Providing & Fixing of IK09 recessed/surface mounting heavy dutyhorizontal type sheet steel not less then 1.2 mm thick Distributionboard as per PWD specification for electrical Works ISI markedconforming to IS-13032 & IS-8623 / conforming to IEC 61439-3.Phosphatised/ powder painted complete with suitable ratinginsulated copper bus bar, shorting link , neutral link, earth link ,connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . IP-43 Double door (single phase) ,6 Way (6 O/G +2 I/C )
177	Providing & Fixing of IK09 recessed/surface mounting heavy dutyhorizontal type sheet steel not less then 1.2 mm thick Distributionboard as per PWD specification for electrical Works ISI markedconforming to IS-13032 & IS-8623 / conforming to IEC 61439-3.Phosphatised/ powder painted complete with suitable ratinginsulated copper bus bar, shorting link , neutral link, earth link ,connecting wire of suitable rating and din bar,masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . IP-43 Double door (Three phase) , 4 Way ( 12 O/G + 8 I/C )
178	Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceiling roses as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABSmaterial, brass terminal & captive screws including makingconnection testing etc. as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
179	Providing & Fixing of ISI marked (IS:1258) 6 amp batten/anglelamp holder as per PWD specification for electrical Works, madeout from industrial grade Polycarbonate or fire resistant ABSmaterial, brass terminal & captive screws including makingconnection testing etc. as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/work , refer Annexure \"A\" attached with this BSR .
180	Providing & Fixing of energy efficient /energy saving IP 20 LEDdirect retrofit Bulb in existing holder or fixture as required withsystem lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum 25000 Burning Hours with , 70% ofintial Lumen maintaned till life ends , CCT 3000°K / 4000°K /5700°K /6000°K/6500°K (As per ANSI Bin) , maximum powerconsumption should not more than the specified rating and Fixtureshall be of BIS standard and trade mark certificate ( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screenprinting on housing. OEM must have its own in house NABL labsetup for all testing facilities for LED fixtures. (LM79/LM80)certificate / Report from OEM shall be submitted. All as per preapproved by engineer in-charge . for additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR. 15 Watt
181	Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Unarmoured / Armoured copper cable of 1.1 KV grade as per PWDspecification for electrical Works in existing RCC / Hume /Stoneware / PVC pipe/ open duct/cable trench with filling ofexcavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:-(a) Copper conductor of electrlytic grade copper, purity >99.97 %ISI marked as per IS:1554 P-I / IS :7098 P - I(b) conductor shall made of copper rods confirming to IS 613-1964, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures (c) OEM Must have ISO 9001 & 14001 certifications & its own in house NABL lab setup for all testing facilities for cables .Appropriate type test certificate / OEM test report shall be submitted . All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
182	Plate Earthing as per PWD specification for electrical Works as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. \"B\" class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .
183	Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu thimble etc. as required. All as perpre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR . 6 SWG copper Wire
184	Providing & Fixing of copper tape 20mm x 3 mm on parapet orsurface of wall fixed with porcelain or bakelite insulator (SP-35) invertical/horizontal run as required. All as per pre approved byEngineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR , 20mm x 3mm copper strip
185	Providing & Fixing of IP20 SMD Mid Power LED batten typeintegrated light fixture made from polycarbonate /extrudedaluminium powder coated housing with in built driver , PowerConsumption of 18W/20W ,system lumen efficacy ≥ 120 lm/Wattoutput, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% ,p.f.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR. 4\" LED Tube shape fixture 18/20 W (Extruded Al Base)
186	Providing & Fixing of Heavy duty capacitor start, copper woindDouble ball bearing 900/1400 RPM single phase Exhaust fan asper PWD specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an ISO certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . 300 mm sweep(900/1400 RPM)
187	Providing & Fixing of ISO Certified company made BEE Approvedcopper wounded 1200 mm sweep BLDC technology power savingceiling fan with longer life span and low maintenance 5 star ratedwhich can withstand on votage fluctuations from 140 volts to 240volts ,power factor not less then 0.9 , service value (CMM/W)minimun 6.85 , air delivery minimun 215 CMM, speed 350 RPM (tolerance as per IS:374 2019 ) THD less then 10% and completewith down rod up to 30 cm with secondary support safety cable ,cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductormaking connection testing etc. as required. Appropriate OEM testcertificate shall be submitted by contractor. All as per pre approvedby Engineer in charge. For additional technical parameters ofproducts/ work , refer Annexure \"A\" attached with this BSR .Without Remote
188	Providing and fixing of non modular power plug point accessoriesas per PWD specification for electrical Works with 18 SWG G I boxof size 175 x 100 x 60 mm with earthing terminal/connector onrecessed/surface with suitable size phenolic laminated sheet (IS :2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and3/6 pin 16 amp. socket outlet [ as per detailed in respective item inBSR], making connection , testing , etc. as required. All as per preapproved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached withthis BSR .
189	P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR. 50 mm Please Enable Macros to View BoQ information

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Rajasthan Tenders

Construction Tenders

Fabrication and Casting Tenders

PEB Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Shelter Home At Pindwara ., Pindwara-Rajasthan

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Shelter Home At Pindwara ., Pindwara-Rajasthan

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us