Proposed Furniture Work At Kusumagraj Smarak In P.No.12 Nashik West Division.-1 COLLECTION counter Providing & fixing COLLECTION counter as per design of 0.9 m width & 1.2 in height with drawers above in 19mm thk. waterproof ply for frames, sliders & drawer facia,6mm thk. plywood for back & drawer bottoms with 12mm plywood for drawers, drawer side with bte lipping to all exposed edges of plywood including 1.mm thk. Laminate on top & 1mm thk laminate on sides & front of drawer facia & sliding shutters with necessary tower bolts castors handles, locks,etc.complete.with oil paint to all exposed surfaces of ply & lipping. Additional item Spec. no. as directed by Spec.No.: RA 22-23 A GROUND FLOOR 2 Providing and fixing vertical/roller blindes for window as approved by engineer in charge and architect GEM ID - 5116877-93262266948 Spec.No.: QUOTATION ATTACHED A GROUND FLOOR 3 GODREJ -ENTERPRIES TABLE 1200X600 X750 Enterprise 1200 Table without CPU Hanger size shall be 1200 Width mm x 600 Depth mm x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . Spec.No.: AS PER QUTATION A GROUND FLOOR 4 GODREJ MAKE REVOVING CHAIR THRILL FULL BACK 1. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area .The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are *HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) *FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H) *SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. 3. ARMRESTS (THRILL PLUS CHAIR) : The adjustable armrest is designed with the following features · Up-Down adjustment- 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. 4. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment 5. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm 6. PEDESTAL ASSEMBLY ( THRILL PLUS) : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). 7. TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. Spec.No.: AS PER QUTATION A GROUND FLOOR 5 GODREJ MAKE RELFEX CHAIRS WITH STACKEBALE TYPE 4 METAL LEG . SEAT / BACK ASSEMBLY : The Seat is injection moulded in glass filled Polypropylene compound which is upholstered with fabric upholstery covers and moulded Polyurethane foam. The Back is injection moulded in glass filled Polypropylene compound which is upholstered with Mesh fabric (Refer colour chart for seat & Back upholstery in product catalog). * SEAT SIZE : 50.0cm. (W) x 48.0 cm. (D) * BACK SIZE : 53.0 cm. (W) x 39.0cm. (H) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression. 3. M.S. POWDER COATED FRAMES FOR 4 LEG CHAIRS :The powder coated ( DFT50±10 microns) welded tubular main frame is made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm andØ1.6±0.3mm x 0.16 ± 0.0128cm M.S. E.R.W tube. The Ø1.9 ±0.3mm x 0.12 ±0.0096 cm M.S.E.R.W. tube used as connecting member between LH & RH frames. Desk let support frame is made from Ø 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and welded to mainframe. Spec.No.: AS PER QUTATION A GROUND FLOOR 6 GODREJ MAKE GAIN 8 FT HIGHT GLASS DOOR BOOK RACK- 2325 H x 900 W x 450 D GAIN PRO STORAGE (BOOK RACK) 2325 H x 900 W x 450 D EACH UNIT SIZE Construction & Material - Aesthetically appealing completely knock down construction. The add-on units are stack widthwise to form arow of storage.(Note- Single Main unit should not be offered. Minimum 1Main + 1Addon to be offered)Legs fitted with screw type leveler.Made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for 450W/600W and 0.8mm CRCA for 900W/1200W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). ** - CRCA D Grade as per IS-513Shelving - It is a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513) Each shelf has max Load Capacity of - 4 Nos. of fixed shelves for 1950(H) A4 size Box file (85Wx340Hx285D) can be stored vertically on all loading levels (Refer Sheet 4 of 17) Number of files that can be stored in one shelf is as follows: Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10 micron). Construction & Material - Made from 0.6mm Thick CRCA (D Grade, IS-513) Soft closing Hinge Handle - Asthetically appealing handle made of Aluminum Cam Lock -3 Way locking provision. Click action mechanism. #NAME? positions. Zinc alloy die cast housing. Finish - Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10 micron).Material to be supplied by certified ISO 50001:2018, ISO 9001:2015, ISO 14001:2015, ISO 45001:2018, ISO 13485:2016, AIOTA member. Item should have at least one of the GRIHA/GREENGAURD/GREENPRO/ GREEN ASSURANCE Certifications adhering to standard environmental practices. Valid test certificate should be available for the item under consideration. Also, OEM must have dedicated toll free service number. Spec.No.: AS PER QUTAION A GROUND FLOOR 7 UPBEAT Discussion Table without wire manager-Size-900 Dia.750H MM Upbeat is a Complete office Furniture setup solution, designed to cater to the various settings in an office space.19mm thick both sided laminated MDF top Metal leg with epoxy powder coating Spec.No.: AS PER QUTATION A GROUND FLOOR 8 Excavation for foundation in earth, soil of all types, sand,gravel and soft murum, including removing the excavatedmaterial up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering,preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc.complete. (Lift upto 1.5 m.) By Mechanical Means Spec.No.: Bd.A.1 PageNo. 259 I.NO 21.0 2 A GROUND FLOOR 9 Excavation for foundation in hard murum includingremoving the excavated material upto distance of 50metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming,watering including shoring and strutting etc. complete. (Lift upto 1.50 m) By Mechanical Means Spec.No.: Bd.A.2 PageNo.269 I NO 21.0 6 A GROUND FLOOR 10 Filling in plinth and floors with Contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec.No.: Bd.A.11 Page 253 21.37 A GROUND FLOOR 11 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec.No.: Bd.A. 12 PAGE 254 21.38 A GROUND FLOOR 12 Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.: Bd.E.4 Page No. 289 and B-7, Page No.38 I.NO.24.08 A GROUND FLOOR 13 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.: Bd.F.6 Page No. 300 and B.7, Page No.38 I.NO.25.50 A GROUND FLOOR 14 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering,ormwork, cover blocks,laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.: Bd.F.8 Page No. 302 and B.7, Page No.38 I.NO.25.70 A GROUND FLOOR 15 Providing and laying Cast in situ/Ready Mixcement concrete M20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/Concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.: Bd.F.9 Page No. 303 and B.7, Page No.38 I.NO.26.05 A GROUND FLOOR 16 Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec.No.: Bd. F. 12 Page No. 304 and B -7, Pg 38 I.NO.26.23 A GROUND FLOOR 17 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps,footings, foundations, slabs, beams columns, canopies,staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules.including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec.No.: Bd.F.17, Page No.306 I.NO.26 0.33 A GROUND FLOOR 18 Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. Spec.No.: As director by engineer in c harge and BDG- 2 and 5 I.NO.27.12 A GROUND FLOOR 19 Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Spec.No.: As director by engineer inch arge and BDG- 2 and 5 I.NO.27.13 A GROUND FLOOR 20 Providing uncoursed rubble masonry of trap / granite /quartzite / gneiss stones in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water manually, striking joints on un exposed faces and watering etc.complete. Spec.No.: Bd.H.1 Page No.329 I.NO.28.0 1 A GROUND FLOOR 21 Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. Spec.No.: As directed by Engineer in c harge. I.NO. 31.04 A GROUND FLOOR 22 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc.complete. Spec.No.: Bd. L.2 Page No. 368 I.NO.32 0.03 A GROUND FLOOR 23 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec.No.: Bd.L.7 Page No. 369 I.NO.32. 11 A GROUND FLOOR 24 Providing neeru finish to plastered surfaces in all positions including. Spec.No.: Bd. L.10, Page 370 I NO. 32. 15 A GROUND FLOOR 25 Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. Spec.No.: Bd.M. 12 Page No.385 I.NO.33 0.42 A GROUND FLOOR 26 Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. Spec.No.: Bd.M. 12 Page No.385 I.NO.33 0.43 A GROUND FLOOR 27 Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec.No.: As directed by Engineer in c harge. I.NO.35.25 A GROUND FLOOR 28 Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (excluding the primer coat)etc. complete. Spec.No.: Bd.P.6 Page No. 414 I.NO.36. 12 A GROUND FLOOR 29 Providing and Fixing of Mineral Fibre Board Acoustical Suspended Ceiling System with ultima (Bevelled Tegular) Edge Tiles of size 15mm Exposed GRID. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.7, Light Reflectance 85%, Thermal conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 20mm , suitable for Green Building application, with Recycled content of 32%. The tile shall be laid on precoated G.I.channel on XL2 Clip having a web height of 32 mm with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm and 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7.7 Kgs/M2 and minimum pull out strength of 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system. The Tile and Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476 etc. complete. Spec.No.: As directed by Engineer in c harge. I.NO.38.45 A GROUND FLOOR 30 Providing and fixing frame with / without ventilator of size as specified with Country non teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete. Spec.No.: As directed by Engineer inch arge. I.NO.39.02 A GROUND FLOOR 31 Providing and fixing steel ventilator fully glazed partly fixed as per detailed drawing without hot dip zinc coating including fabricating glazing with plain / obscured glass panes 5 mm thick and approved type and quality and iron oxidized fixtures and fastening oil paint 2 coats etc. complete. Spec.No.: BD-T-53 Page No. 509 As dire cted by Engineer in charge I.NO.39.29 A GROUND FLOOR 32 Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm . Spec.No.: As directed by Engineer in c harge. i. no.39.56 A GROUND FLOOR 33 Providing and fixing 30mm thick PVC FLUSH L DOOR SHUTTER consisting of panel of hollow PVC profile of 20 mm thickness consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mminserted inside the hollow section of stiles rails top ?and bottom rails and two 19x 19 mm MS tubes inserted horizontally inside the hollow profile section using 4/5 mm sheet using screws hollow profile shall be lipped with 10 mm (5mm x2) thick x 20 mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof waterproof plain /prelam PVC sheet using solvent cement on the both sides of the panel including stainless steel fixtures and fastening etc. Complete as per direction of Engineer incharge, manufacturers specification and drawing. Spec.No.: As directed by Engineer in c harge. i. no.39.82 A GROUND FLOOR 34 Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. Spec.No.: Bd.V.8 Page No. 554 I.NO.41. 400 A GROUND FLOOR 35 Providing and fixing screw down for 50 mm dia. wheeled stop tap of brass including necessary sockets/ union nut complete. Spec.No.: Bd.V.9 Page No. 555 I. NO.41 0.48 A GROUND FLOOR 36 Providing and fixing 15mm diameter concussion push button type brass/gun metal self-closing tap including necessary socket complete. Spec.No.: Bd.V.14 Page No. 557 I.NO.41 0.52 A GROUND FLOOR 37 Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe. Spec.No.: Bd.V.23 Page No. 562 I. NO.4 1.57 A GROUND FLOOR 38 Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. Spec.No.: Bd.V.30 Page No. 565 I. NO.4 1.63 A GROUND FLOOR 39 Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and Spec.No.: BdV41 PAGE NO 573 I NO 42.07 0 A GROUND FLOOR 40 Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75 kg with lid and frame fixed in cement concrete. Spec.No.: Bd.V.43,Page No.574 I.NO.42. A GROUND FLOOR 41 Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. Spec.No.: As directed by Engineer inch arge. I.NO.42.200 A GROUND FLOOR 42 Providing and Fixing half turn 25 mm dia gun metal flushing cock including all accessories etc. complete. Spec.No.: As directed by Engineer in c harge. I.NO.42.320 A GROUND FLOOR 43 Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec.No.: BD.V 5 page 551 and as direc ted by Engineer in charge I.NO.42.550 A GROUND FLOOR 44 Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec.No.: BD.V 5 page 551 and as direc ted byEngineer in charge I.NO.42.580 A GROUND FLOOR 45 Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec.No.: BD.V 5 page 551 and as direc ted by Engineer in charge I.NO.42.600 A GROUND FLOOR 46 Providing and fixing 10 cm PVC nahani trap with grating etc. complete. Spec.No.: BD.V 32 A page 551 and as di rected by Engineer in charge I.NO.42.670 0 A GROUND FLOOR 47 Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32mm size of approved make including soil pipe, vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete. Spec.No.: As directed by Engineer Inch arge I.NO.42.860 A GROUND FLOOR 48 CARTING UN WANTED MATERIAL FROM SITE UP TO 5 KM Spec.No.: AS DIRECTED (LEAD CHRGES FOR 5 KM) A GROUND FLOOR 49 Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Spec.No.: As directed by Engineer inch arge. I.NO.46.090 A GROUND FLOOR PART B (ELECTRICAL) 1 Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories (PWD DSR 2023-24, 1-7-18) 2 Point wiring for ceiling fan in PVC trunking (casingcapping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories (PWD DSR 2023-24, 1-7- 19) 3 Point wiring for independent plug in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories (PWD DSR 2023-24, 1- 7-20) 4 Wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories (PWD DSR 2022-23, 1-7-25) 5 Providing and fixing PVC trunking (PVC casing-ncapping) of size 25 mm with accessories on wall/ceiling (PWD DSR 2023-24, 1-2-7) 6 Providing and fixing HMS PVC conduit 25mm dia. with PVC accessories on wall/ceiling (PWD DSR 2023-24, 1-2-4) 7 Concealing of provided G.I. pipe/H.G. screwed conduit/PVC pipe in wall/floor/false ceiling (PWD DSR 2023-24, 1-1-13) 8 Providing and fixing mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking (PWD DSR 2023-24, 3-1) 9 Providing and fixing mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking (PWD DSR 2023-24, 3-2) 10 Providing and fixing mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking (PWD DSR 2023-24, 3-3) 11 Providing and fixing LED 22W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete (PWD Elec 2023-24, 2-1-18). 12 Providing and fixing LED square / circular Max. W down lighter / Panel Light having pressure diecast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens,(PWD DSR 2023-24, 2-1-5) 13 Providing and fixing LED Panel Light (600mm X 600mm) Max. 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min 4200 Lumens, etc complete (PWD DSR 2023-24, 2-1-5) 14 Providing and fixing Ceiling fan 230 V A.C. 50 cycles 1400 mm etc complete (PWD DSR 2023- 24, 2-9-3) 15 Providing and fixing modular type electronic step regulator for fan etc complete. (PWD DSR 2023- 24, 2-10-9) 16 Providing and fixing fan clamp of 30 x 5 mm. M. flat of required length and 10 mm. M.S. bolt and nuts erected with necessary hook of 10 mm. M.S. round bar and painted. (PWD DSR 2023-24, 2-10- 3) 17 Providing and fixing ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected (PWD DSR 2023-24, 2-10-6) 18 Providing and fixing bracket fan 400 mm. sweep A. C. 230 volts 50 cycles 1350 RPM. Oscillating type, plastic or metal blades chrome plated guard with speed regulator (PWD DSR 2023-24, 2-9- 19 Providing and fixing exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials (PWD DSR 2023-24, 2-9- 13) 20 Providing, fixing and marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board (PWD DSR 2023-24, 5-3-3) 21 Providing, fixing and marking DPMCB 40A to 63A, B- series (for lighting) in provided distribution board (PWD DSR 2023-24, 5-3-9) 22 Providing, fixing single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 2 ways (2 poles) for outgoing SP MCBs (PWD DSR 2023-24, 5-4-7) 23 Providing and fixing single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, (PWD DSR 2023-24, 5-4-9) 24 Providing, fixing testing and commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 5.00 suitable operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete (PWD DSR 2023-24, 3-2-9) 25 Providing, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete(PWD DSR 2023-24, 3-2-13) 26 Providing and fixing PVC insulated PVC round sheathed 2.5 sq.mm 3 core flexible multi stranded copper Industrial cable for voltage grade up to kV (PWD DSR 2023-24, 1-3-15) 27 Providing and fixing copper pipe suitable for refrigeration system having size 12 mm complete. (PWD DSR 2023-24, 3-2-26) 28 Providing and fixing bracket for split type AC 29 Providing and fixing copper pipe suitable for refrigeration system having size 16 mm complete. (PWD DSR 2023-24, 3-2-27) 30 Providing and fixing Elastomeric Nitrile rubber / foam tube type sleeves for over coating and insulating on provided copper pipes having sizes 12 mm (PWD DSR 2023-24, 4-2-3) 31 Providing and fixing Elastomeric Nitrile rubber / foam tube type sleeves for over coating and insulating on provided copper pipes having sizes 16 mm (PWD DSR 2023-24, 4-2-4) 32 Providing and fixing rigid PVC pipe 20 mm dia.with PVC accessories for drain (PWD DSR 2023-24, 1-2-3) 33 Providing and fixing meter box with all accessories complete. 34 Providing, laying and terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe (PWD DSR 2023-24, 7-1-28) 35 Providing, fixing and testing earthing with galvanised iron earth plate size 60 x 60 x 0.6 cm complete with all accessories of GI materials and recording the results (PWD DSR 2023-24, 9-1-1) 36 Providing and fixing GI earth wire of high purity of different sizes used for earthing. (PWD DSR 2023- 24, 9-2-5)
