Tender For It Enabled Day And Night Illuminated Acrylic Led Acrylic Graphical Stuffs, Special Effects And Artifacts Including Design, Technological Beautification And Osd In Front Of Papakshya Jagannath Temple Binka, With The Theme Of Jagannath, On Engineering, Procurement & Construction (Epc) Mode Contract , Part 11: It Enabled Day And Night Illuminated Acrylic Led Acrylic Graphical Stuffs, Special Effects And Artifacts Including Design, Technological Beautification And Osd In Front Of Papakshya Jagannath Temple Binka, With The Theme Of Jagannath, On Engineering, Procurement & Construction (Epc) Mode Contract. , Technical Specifications Electronics Led Acrylic Letters Stating ?? ???????. • The Letters Will Be Made Up Of Led Acrylics Of White Colour Stating ?? ??????? With Half Part Of Jagannath Temple And Nila Chakra With Flag. Letter Size: 2Ft Height. • Supported By Jagannath Temple On The Back Of Total Height 7 - 8 Feet Including Nilachakra. • The Jagannath Temple Size Can Be Made As Per The Available Space Around, Again The Decision Can Be Made Whether Too Far In Acrylic Or Backlit Canvass Flex As Required. Back And Side Raising With Aluminium With Ss Finish. • 3-4Mm Thick Acrylics Of Make: Migra Cipta/ Sinkolite Brand Will Be Used. • It Enabled Digital Graphics Module Led (Make: Hisign) Supported By Smps To Be Used For The Individual Letters. Light Source: 1.5W Led Lights. • The Led Acrylic Letters Would Be Fitted On 1.5 Ss Pipes Of 5Ft (3Ft Height Above The Ground And 2Ft Underground) And Grouted With Cement Concrete Inside The Platform. • Power? External Power Supply: 220 - 240V Ac, 50Hz, 33-Amp 12V Dc Water Resistant Power Supply= 15 Nos. The Power Supply Will Be Connected Through The Digital Timers As Required. • Environment? Operating Temperature - -20°C To 80°C Humidity - 0 To 100% Rh Pressure - +/- 10%. , Ss Pole Special Designed Fancy Garden Bollards With Body And Head Lightings As Required Of Total Heights Of Minimum 2.8 Feet Height. , Ss304 Pole Special Designed Laser Carved Fancy Street Lights With Full Body And Head Lightings As Required Of Total Height Minimum 12 Ft. Qty:10Nos. ? The Pole Will Be Of Ss304 Of 2.5 Dia. And 10Ft Height. Out Of Which 8 Will Be The Body With Day And Night Illuminated. ? The Body Of The Pole Out Of Which 8 Feet Will Be Made Up Of 3Mm Acrylic Sheet (Of Required Colour And Design) With It Enabled Acp Router/ Laser Carved (Of Required Colour And Design) Would Be Based Over 1X 1 Square Pipe Of Ss304 For Border Frames Of Size- 8X8 And Of 8Ft Height. 8 Nos. Of Led Rod Of 3.5 Height Of 22 Watts Each To Be Installed Inside It For Illumination (Of Required Colour). ? At The Top, A Head Light With Aluminum Casting Of Minimum Of 30 Height Will Be Placed. A Driver Based Led Of 50 Watt Of Warm White Color Will Be Used For The Top Illumination. ? The Bottom End Part Of The Pole Of Fancy Light Post Will Be Covered With Designed Multi-Layer Frp Base (With Pot-Like Design) Of Dimension - 10 Base Dia. And 4 Top Dia., Having Golden Colour. Additionally, 2Nos. Of Multi-Layer Frp Designed Rings Of 3 Height & 4 Dia., Will Be Provided Over The Base Pole, For Better Look. ? The Entire Pole Will Be Supported With Required Civil And Mechanical Foundation As Required. Underground Foundation Supported With A 2 Depth X 1 Length X 1 Breadth Reinforced Cement Concrete Civil Foundation And Plinth As Required Inside The Ground. Underground Base Will Be Made By Digging 2Ft Underneath, And Filling It With Concrete And Securing The Concrete With A Baseplate. The Cast Iron Base Design Will Be Joined With The Base Plate With Nut Bolts. ? Base Plate At Bottom Would Be Of 10 Mm Thickness X 10 X 10 Size Ms Plate. ? Nuts Would Be Of Minimum 8/10 Mm * 4 Numbers And The Required Height Would Be Of 2 Feet As Required. Ring Size Would Be Of 8/10 Mm Rods, With Base Plate Of 8/10 Mm. ? The Foundation Of The Street Pole Is Depending Upon The Available Conditions. ? The Dimensions Mentioned In This Specification Are Tentative Only May Differ A Bit. , The Complete Industrial Underground Electrical Connection By Using The Hard Pvc Pipes And 2.5Mm Core Wires To Be Connected To The Points For Required Electrical Supply Would Be Supported By Mcbs, Connectors, Timers, Switches And All. , Focusing Lights To Be Made Focus To The Artifacts And Peripheral Trees, As Required. The Statues Will Be Made Lighting With The Help Of Special Light Effects Of Rgb Of 200W Each (Qty: 1Nos.) Along With Other Lightings. The Platform Will Be Illuminated With The Help Of Best Quality Led Strip Lights. , Artifacts Statue Of Radha Krishna With Cow, Of 7Ft Height Made Up Of Multi-Layer Frp With Partial Fire And Heat Resistant Properties , Ganesh Statue Of 4-5Ft Height Made Up Of Multi-Layer Frp With Partial Fire And Heat Resistant Properties. , Relief Art Of 70Ft X 6Ft, With Any Traditional Design Of Konarka Chakra And Temples. The Relief Art Will Be Made Up Of Multi-Layer Frp With Water Resistant And Partial Heat Proof Properties, Of 445 Sq Feet. , Civil Garbage Cleaning Of The Entire Site Of 1000 Sq. Ft. Area. , Soil Filling In The Whole Site Around 2000 Cu. Ft. , Cut-Off Wall Will Be Made Of Reinforced Cement Concrete With External Brick Work To Install The Ss Railing To Safeguard The Artefacts Of 90 R. Feet Length X 1Ft Height Above The Ground And 1.5Ft Underground X 10Mm Width. 12Mm Thick Plastering (1:6 Ratio) On 3 Sides Of The Cut Off Wall. 3 Dpc On Top Of The Wall To Place The Ss Railing As Required. The Cut-Off Wall Will Be Supported By 10Mm Ms Vertical Rods And 8Mm Ms Horizontal Rods In The Foundation To Act As Ribbing To Provide Extra Support In The Foundation. The Cut Off Wall Will Be Supported By Pillars As Required. The Ss Railing Will Be Grouted For A Rigid Stay On The Cut Off Wall. , Special 3D Painting Of The Cut-Off Wall With Traditional Designs As Required 300 Sq. Feet. , The Entire Location Will Be Surrounded With Ss Railing Raised Over 1Ft Of Cut-Off Wall. Ss Railing Of 2 Dia. Vertical Pipes (Columns) Of 3Ft Height Supported By ¾ Ss Pipes Of 3 Or 4 Rows To Be Placed Horizontally In Between The Vertical Columns. The Main Top Horizontal Pipe Will Be Of 2 Dia. Ss Railing Will Be Installed Over A Running Feet Of 90 Ft. The Master Pillars Of 3 Dia Would Be Placed At 9 Feet Apart And Would Have Designed Ball On Top. The Idlers Vertical Stand Would Be Provided In Order To Provide Support To The Horizontal Pipes. The Horizontal Pipes Would Have The Balls Fitted On It To Provide Extra Lucrative Look. , Platform To Install The Radha Krishna Statue Made Of Rcc: Of 4Ft X 4Ft X 2Ft Height Platform (2Ft Will Be For Foundation). The Platform Will Be Made Of Reinforced Cement Concrete And External Brick Work, With Proper Finishing Along With Plastering And Painting As Required. 3 Dpc On Top Of The Platform For Smooth Finish. 10Mm Ms Vertical Rods And 8Mm Ms Horizontal Rods To Be Provided, In The Foundation To Act As Ribbing To Give Extra Support In The Foundation. The Platform Will Be Supported By Pillars As Required. The Statues Will Be Grouted With Reinforced Cement Concrete For A Rigid Stay Within The Platform , Metal Framing Of 70Ft X 6Ft With Ms/Gi Angles Of 1.5 Ss Pipes, For Supporting The Relief Art. , Horticulture: - Plantation Of Mexican Grass In The Whole Site Of Around 1000 Sq. Ft. Prior To That Soil Levelling, Compaction, And Anti Demit Treatment And Plantation Of Grass And Trees. , Plantation Of Other Design Trees And Other Flower Plants As Required In The Whole Site. , Detailed Design And Maintaining The Changes As Required Of The Projects. , Consultation And Engineering Supervision. , Complete Transportation, Handling, Storage And Hence Then Installation As Required. , Contingency And Risk Consideration. , Miscellaneous And Overheads As Required. , Annual Maintenance Contract For 1 Year, Which Does Not Include The Garden Watering And Maintenance Of The Horticulture. Please Enable Macros To View Boq Information
