Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M&L for removing old existing rubbish/battered/useless mixture of the binding materials such as cement / Lime and fine aggregate (<4.5mm retained on IS Sieve), loose/unsound weaken mixture of binding materials such as cement / Lime and coarse Aggregate (>4.5mm retained on IS Sieve), fine Aggregate of any description and in any position from existing external/internal surfaces of RCC components or any surface having average profundity of 15mm (Approx height 10m from natural ground level) by hand tool that has a long metal blade with a sharp edge at the end, chisel and hammer or using robust pneumatic chisel hand tools and removal beyond MoD land including cutting of all edges, making square shoulders of the aperture, coarsen the smooth surfaces, curettage /removing of all deterioted/decayed loose surface complete all as specified and directed by Engr-in-charge. |
| 2 | M&L for cleaning and removing all corrosion scales , rust , etc using emery / wire brush and finally cleaning using rust remover & cleaning agent that is one part alkaline based material, with corrosion inhibitors and dispersing agents and supplied as a clear brown solution. The specific gravity shall be 1.2 – 1.22 @ 25°C. The pH value shall be between 9.5 to 10 and the coverage shall be 5 – 6 m2/ L as per manufacturer instructions complete all asspecified and directed by Engineer-in-charge. |
| 3 | M&L for repair to cracks and damaged existing surfaces by Hydrogen Free Expanding And Plasticising Additive . It plasticizes the mix, allowing for substantial reduction in water without affecting the fluidity, thus improving the strength and impermeability, the admixture/ additive in cement to provide non‐shrink properties Cementitious Cable Encapsulation .(a). Fixing of pvc nozzles in zig-zag fashion not more than 50cm c/c on RCC surfaces on all directions as required after drilling holes in concrete, fixing pvc nozzles with fast setting mortar and covering with renderoc plug. The size of holes shall be 20mm dia and 75mm in depthcomplete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for applying Polyster Resin based Anchoring material in concrete before fixing nozzle it should typically attains a compressive strength in excess of 20N/mm @ 3 hours and and ultimate compressive strength of 70N/mm in 7 days (50mm x 50mm x 50mm)when tested as per BS 6319 Part 2 : 1983as per manufacturer instructions complete all asspecified and directed by Engineer-in-charge. |
| 5 | M&L for Shear thinning agents in RCC/ walls/ ceiling/ columns/ beams/floor/bricks cracks after opening up in “V” groove manner covering the area of 300mm from central line of crack with the depth of 8 mm complete with three components compound graded filler, E-Resins and Shear thinning agents with adjustable consistency by varying the filler component epoxy resin based complete all as specified and directed by Engineer in Charge. |
| 6 | M&L for applying 2 coats oftwo component amine cured epoxy mastic coating usingLight brush blasting using nonmetallic abrasive leaving a clean, rough and even pattern.it should bebased on a 100% epoxy formulation and contains no solvents or water diluents. Apply two coats with brush or squeeze to the existing surface, working well into the substrate.it should achieve Compressive Strength of >70 MPa after 14days, having pot life, minutes at 27⁰C, 100 g >40 mass as per manufacturer instructions complete all asspecified and directed by Engineer-in-charge |
| 7 | M&Lfor providing and fixing welded MS wire mesh weighing not less than 1Kg/Sqm of size 50mmX50mm of 2.6mm dia on the prepared surface & surface should be cleaned andbe removed from dirt, fungus and all foreign material complete all as specified and directed by Engineer in Charge. |
| 8 | M&L for applying 2 coats of primer slurry prior to the application of the repair mortar having multiple corrosion inhibiting synergies and which is a blend of pc graded fillers corrosion inhibiting additive and re-dispersible polymers in powder form mixed with water for application by brush to coat the reinforcement/steel within 10mm of the finish surface and where chlorides are present so as to achieve adhesion bond strength of 1 MPa to steel. Pot life of 0.5 hr @ 30°C. It shall be workable for not more than 15 minutes at same temperature. The mixed density shall be not more than 2.05. The water/powder ratio shall be 0.3 by weight complete all as specified and directed by Engineer-in-charge. |
| 9 | M&L for applying 20mm shear thinning fibre reinforced polymer modified , impermeable to aggressive elements, dual shrinkage compensated, cementitious repair mortarwith alkali resistant synthetic fibres for exceptional resistance cracking complies ASTM C 109 with flexural strength ASTM C 348 @ 7 days meeting 7N/sqmm, tensile strength @ 7days (ASTM C 307)> 3 N/sqmm, compressive strength of 35MPa at 7 day and 45MPa at 28 days, at the outer or inner RCC which provides excellent bond to concrete, Improves tensile and flexural properties of mortar, Versatile having specific gravity of 1.02cement sand can be used for finishing purposecomplete all as specified and directed by Engr-in-charge. |
| 10 | M&L for providing and spraying polyamine cured epoxy coatingincorporating a special alkali reactive emulsion breaking system compoundover the plastered surface. This impervious film prevents excessive water evaporation which in turn permits more efficient cement hydration, thus reducing shrinkage and increasing durability. It shall have a specific gravity of 1.02 and the minimum application temperature shall be 10°C and the strength of concrete complies with the internationally recognised ASTM C309-90 standards typically within the range of 200 to 285 ml/sqm, SG - 1.02 including all tools and tackles complete all as specified and directed by Engr-in- charge. |
| 11 | M&L for applying 3 coats of corrosion inhibiting, polymer matrix with excellent mechanical properties such as adhesion and elongation as waterproofing barrier coating. It should be non toxic and non-re-emulsifying. Should conform to JIS Z 1535 and IS-3085 and DIN-1048.having Hardness - Shore \"D\" scale of 20,wet density of 1.66 g/cc, flexibility at low temperatures, tensile strength > 0.4 MPa, Elongation > 20%, adhesion to substrate greater than 1.5 N/mm², waterproofing to withstand 330 KPa positive pressure and 160 KPa negative pressure, Mixing should be done by electric rotary mixers. The substrate should be free of laitance, loose concrete, dust, oil etc. if applied on screed or any other cementitious surface the surface should be properly cured prior to application complete all asspecified and directed by Engineer-in-charge |
| 12 | M&L forapplying two coat of mixture of two monomer unsaturated liquid hydrocarbon , gaseous hydrocarbon and polymesrized them to get the high polymerdispersion emulsion successfully bonded to mortar, to improve adhesion to concrete, better durability, reducedshrinkage and increased flexibility and resistant toemulsification in damp condition modified Ensuring no porosityin new/old surface, temperatures between +5°C and +35°C, Resist to penetration of CO24.600 micron , compressive strength (11.5 N/mm2) at 3days strength - 11.5 (N/sqmm ) and at 28 days - 25.30N/sqmmas per manufacturer instructions complete all asspecified and directed by Engineer-in-charge. |
| 13 | M&L for Sprinkling sand particles of saturant making mechanical key, over which applying Single component, fiber reinforced cementitious repair mortar which is reinforced with specially designed bean shaped, alkali resistant synthetic fibers for exceptional resistance to cracking for a thickness of 10 mm. water ratio of which shall be 0.16, 28 days compressive strength shall be 30 MPa,mixed density shall be 2.18 kg/ltr, flexural strength shall be 6 MPa for 7 days and tensile strength for 7 days shall be more than 2MPa.Its adhesion bond strength shall be greater than 2 MPa with creep strain reduction of 8%.Single component, fiber reinforced cementitious repair mortar.cement and sand can be used for finishing purpose. The modulus of elasticity of this product shall be 23-26 KN/mm² complete all asspecified and directed |
| 14 | Note for item No. 1 to 13 :-The work for items Srl No 1 to 13 shall be executed directly by manufacturer or through their authorized and qualified applicators of any following manufacturer only. M/s Fosroc chemicals, M/s Thermax Limited, M/s BOSTIK India Pvt limited, M/s Tiki Tar Danosa India Ltd. |
| 15 | The contractor must submit MOU with manufacturer/authorized applicator at the time of sample approval. |
| 16 | The contractor shall submit performance guarantee certificate for structural repair/leakage/seepage for a period of 10 years from the certified date of completion. |
| 17 | The unit quoted rate shall be inclusive of material, all labours, tools and plants including scaffolding required for working upto 15 mtr height from natural ground level. |
| 18 | The defect liability period for the structural repair work shall be 05 (five) years from the certified date of completion of work. |
| 19 | A security deposit of value equal to 2.5% of the rate quoted against each item shall be retained from Final bill payment due to the contractor for the defect liability period. |
| 20 | The unit quoted rate is deemed to include taking up or down of water pipe, tanks, wires etc found on roof or other working areas and re-fix same at the original position after completion of work. |
| 21 | Adoption of necessary safety arrangement like safety belts, ropes, helmet, netting etc are required for safety of working labour at height exceeding 3 to 15 mtr shall be mandatory & deemed to be included in the unit quoted rate |
| 22 | M&L Repair to ends of chajjas/ parapets by removing old concrete,loose material &cleaning of the reinforcement and finishing the surface with rich cement mortar 1:3 , finished fair & even and making good with existing finishes complete all as specified and as directed.Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding. |
| 23 | Removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet near pipes etc and applying acid treatment afterremoving roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed. |
| 24 | Taking down chowkhat or frame (wooden/steel) exceeding 1.50 Sqm and not exceeding4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed. |
| 25 | Taking down shutters of any description exc 1.0 Sqm andn.exc 2.0 Sqm each complete all as specified and directed. |
| 26 | M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at jointscomplete all as specified and directed. |
| 27 | Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed. |
| 28 | S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panelswith lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 29 | S&F Factory made 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);all as specified and directed. |
| 30 | Preparation of new wood orwoodensurface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed |
| 31 | Supply and fixing 100mm long Butt hinges medium weight cold rolledstainless steel, and fixed complete all as specified and as directed. |
| 32 | Supply and fixing 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 33 | S&F aluminium handles cast type anodised 200 mm long complete all as specified and as directed. |
| 34 | S&F 250mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed. |
| 35 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed. |
| 36 | S&F 2nd class hard wood Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads in section area 6 sq.cm but not exc 13 sq cm including taking down exisiting one complete all as specified and as directed. |
| 37 | Taking down and refixing MS window shutters n. exc 1.5 sqm through cutting of existing any type of hinges, handle and tower bolt and fixing new box type hinges, MS handle and MS tower bolt to the same window by necessary welding.The quoted rates shall be included the following aspect:-(a) Cutting of existing piano hinges, handle and tower bolt from window frame and shutter.(b) Fixing of removed shutter in the same frame on MS box type hinges 100mm, MS handle 100mm and MS tower bolt 100mm by welding.(c) Easing and adjusting the shutter before re-fixing if required.(d) Finishing the window frame and shutter with two coat of synthetic enamel paint.(e) Necessary scaffolding material to be included as the building height is more than 10mtr.Note :Box type hinges, handle and tower bolt shall be measured separately as supply only and labour element is deemed to be included in this item. |
| 38 | Supply only MS Box type hinges 50mm. |
| 39 | Supply only MS Handle 100mm. |
| 40 | Supply only MS tower bolt 75mm |
| 41 | Supply and fixing in repair steel window peg stay all as specified and directed. |
| 42 | Petty repair to easing of wooden window, wooden ventilator, cupboard door, wardrobe door,PVC door, window shutters, kitchen cupboard shutters, show case shutter drawers including fixing of screws adjusting handles, knobs tightening piano hinges including misc small adjustments , (size upto 3 Sqm). minor repair and easying and adjustment/alignmentto openable with accessories and including taking down and refixing complete all as directed. |
| 43 | Taking down chowkhat or frame(wooden/steel) not exceeding1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed. |
| 44 | S&F in Steel windows with side hung shutters including projecting type hinges, frame with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 45 | S&F 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50sqm in each pane complete all as specified and directed. |
| 46 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and directed. |
| 47 | S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC\"C\"channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitablePVCsheetbeadingand jointed together with solvent cement complete all as specified and directed. |
| 48 | S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed. |
| 49 | Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 50 | Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed. |
| 51 | M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm in each pane complete all as specified and directed. |
| 52 | M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass exc 0.5 sqm in each pane complete all as specified and directed. |
| 53 | Providing and injecting chemical for post constructional Anti TermiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and directed. |
| 54 | Petty repair to door shutters for easy closing/opening(size upto 3 Sqm) including minor repair and easing, adjustment/alignmentto openable with assessories and including taking down and refixing, tightening of hinges or changing the position of hinges,welding of hinges door to frame adjustment of tower bolts, sliding bolts with new screws etc,complete all as specified and directed. |
| 55 | Petty repair to toilet floor, bathroom, kitchen, etc seepageincluding sunken portion treatment with apply water proofing compound including repair and arrest the leakage to floor trap,nahani trap , grating and applying white cement etcmaking good to the damaged portion of flooring, laying and matching of existing flooring, complete all as specified and directed. |
| 56 | M&L for Treatment of the sunken floor slab comprises of the following specification and all as specified and directed.Make :-Dr Fixit/ M/s Sika india Pvt Ltd/ STP Ltd/ M/s Fosroc Chemicals |
| 57 | (a) Demolition of cement concrete filling of any description in sunken portion in toilet and removing debris outside MD land. |
| 58 | (b) Cleaning the sunken/ lowered portion of RCC slab surfaces (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding conc to achieve proper slope including cutting holes in bricks or RCC wall for spout (WPC shall be measured and paid separately) |
| 59 | (c) Rendering of uneven surfaces with 10mm thick in CM 1:4 mixed with integral water proofing as per manufacturer instruction. Fill it with water and check dampness and seepage. Where dampness/ seepage is noticed, nozzles shall be fixed and grouting carried out. (WPC shall be measured and paid separately). |
| 60 | (d)All junctions points of side wall spout where CI/ GI pipes are passing through shall be sealed with epoxy putty. |
| 61 | (e)After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. |
| 62 | (f) Material and labourfor applying two coats of polymer modified cementious water proof coating as per manufactures instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. |
| 63 | (g)Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound as per manufacturers specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately). |
| 64 | (h)Material and labourfor PCC 1:5:10 type E2, n exc 150mm thick complete all as specified |
| 65 | (j) Material and labourfor PCC 1:2:4 type B0 12.5mm thick aggregate, 50mm thick complete all as specified |
| 66 | Note for item No 56 to 65 :- Test the water proof area (ponding test) by filling water for at least 72 hours and tested for leakage, seepage to the entire satisfaction of GE. |
| 67 | Test shall be done in presence of Engineer-in-Charge. |
| 68 | The treatment shall be carried out by authorised applicator of chemicals. Cost of testing is included in the unit quoted rate above. |
| 69 | SupplyOnly integral water proofing compound complete all as specified and as directed.Make:-Dr. Fixit Pidi Proof and equivalent. |
| 70 | Material and labourfor Water proofing treatment to the sunken portion applying two coat of two component (1 part Polymer and second part cementations powder) cementations, polymer modified elastomeric, water proofing coating composed of cement, properly selected and graded aggregates, additive and acrylic emulsion polymer as a binder apply first coat of (mix and application as per manufacturer’s instructions) all over floor surface. Prepared surface and apply to vertical surface up to 15cm from tiling level, allow to dry 4 to 6 hours. Prepare for apply 2nd coat perpendicular to first coat and allow to dry 4 to 6 hours. All joints to Trap/WC/Soil pipe shall be properly sealed with ceiling compound/polymer modified mortar using Dr Fixit Pidicrete UBP or equivalent in M/s Pidilite orM/s Sika Chemical, Slope of slab shall be towards and including GI pipe 50mm dia of suitable length Spout pipe. Providing 15mm protective screed with cement mortar in 1:3 with WPC (Make : Dr Fixit LW + or equivalent in M/s Pidilite orM/s Sika Chemical) within 2 to 3 days of second coat complete all as specified as per manufacturer instructions. Make : Dr Fixit Pidfin 2K or equivalent in M/s Pidilite orM/s Sika Chemical complete all specified and directed by Engineer-in-Charge. |
| 71 | Note for item No 70 :- The work shall be carried out by authorised and qualified applicators of the above mentioned manufacturer. |
| 72 | M&L Repair to leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ washbasin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe embeded in floor in bathroom or kitchen making good to the damaged portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed |
| 73 | M&L Repair to leakage/seepage from the wall/ door bend /door tee/\"Y\" junction/ \"T\" Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damaged soil waste pipes or fittings of any shape, specification and size, making good to the damaged portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and finished the surfaces matching to existing wall to avoid the leakage/ seepage at the site of work complete all as specified and directed. |
| 74 | Note for item No 72 & 73:- (a)Find out main cause of leakage and take necessary steps to resolve / rectify.(b)Replace existing tiles in case leakage through NT/FT.(c)The rate also include provision of new NT/FT.(d)The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as directed by the manufacturer\"s specification. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit |
| 75 | Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off from premises & M&L forceramic coloured tiles of size 350mmx250mm/ 300mm X 450mmx7 to 8 mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured / white cement to match the tiles inc rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc complete all as specified and directed. |
| 76 | Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off from premises & M&L for joint free non skid coloured ceramic tiles 7 to 8 mm thick area of each tile not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointedin white or coloured cement to match incl 15 mm thick screed bed in cement mortar 1:4 for layingfloor finishes complete all as specified and directed. |
| 77 | S & F in repair viterous china squatting pan \"Orissa pattern \" size 580 x 440mm white with integral foot rests incl connecting to \"P\" or \"S\" trap and to flush pipe anti syphonage pipe etc complete including provn of lime concerte bedding and making good to floor complete all as specified and as directed. |
| 78 | S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenchesbore of pipe 75 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed |
| 79 | S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenchesbore of pipe 110 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed |
| 80 | S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and as directed. |
| 81 | S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and as directed. |
| 82 | S & Fin repairs PVC (SWR)junction single (single T)equal or unequal with access door bore of pipe 75 mm complete all as specified and as directed. |
| 83 | S & Fin repairs PVC (SWR)junction single (single T)equal or unequal with access door bore of pipe 110 mm complete all as specified and as directed. |
| 84 | S & F in repairs 125/ 110 mm bore PVC (SWR) floortrap plain with grating incl jointing with solvent cement complete all as specified and as directed. |
| 85 | S&F in repairs PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 86 | M&L for Preparation of old decoratedplastered or unplastered surfaceof wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat oil bound distemper complete all as specified and as directed. |
| 87 | M&L for preparation of old plastered surfaces of wall by using pressure washer, removal all dirt and dust and applying one coat of exterior emulsion (APEX) weather proof paintcomplete all as specified and as directed. |
| 88 | M&L for Preparation of old painted wooden surface of any description and applying one coats of synthetic enamel paintnot otherwise described over 10 cm width or girth, complete all as specified and directed. |
| 89 | M&L for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paintover 10 cm width or girth, not other wise describedcomplete all as specified and as directed. |
| 90 | Taking down existing manually/machine operated steel rolling shutters area not exc 30Sqm each and erecting in same position, after easening, applying of greasing of all parts in rolling shutters uncluding changing of anchor rod, springs, steel rolling strips, locking plate, ball bearings. locks and vertical channels all as directed. Spare parts shall be measured and paid separately, after replacement of following unserviceable parts as required for smooth functioning of rolling shutter and refixing properly including bracket complete all as specified and directed. |
| 91 | (a) Shaft 50mm mild steel pipe all as directed. |
| 92 | (b) Helical spring 600mm long all as specified and directed. |
| 93 | (c) Ball bearing for 50mm dia pipe all as directed. |
| 94 | (d) Gear box setall as specified and directed. |
| 95 | (e) Lath patty (strips) of 75mm wide & 1.20 mm thick MS all as directed. |
| 96 | (f) Crancked wheel of any size all as directed. |
| 97 | S & F in repairs Steel rolling shutters, in any size and any position with ball bearing, as specified including top cover, anchoring rod, shaft, lath patty,crank wheel, side cover, hood cover, locking plate, hasp and staple and one shop coat of primer; erected in position as indicated, complete manual or gear operated type. Thickness of laths 1.25mm complete all as specified and directed. |
| 98 | M&L for cement plaster rendering 15mm thick on fair faces of brick/concrete surfaces with two coats i.e. (10mm thick backing coat in CM 1:6 and 5mm thick finishing coat in CM 1:4) and mixed with liquid water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement (WPC to be measured and paid separately) and Taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed. |
| 99 | M&L for cement plaster rendering 10mm thick in CM 1:6 on fair faces of brickwork or concrete surface as on wall finished even and smooth with thin layer and taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed. |
| 100 | M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces with smooth finish of any description, complete all as specified and as directed. |
| 101 | M & L for preparation of new plastered surfaces of walls applying plaster of paris putty of one coat over plastered surface to prepare the surface even and smoothfinish and applying two finishing coat of oil bound distemper over a coat of primer complete all as specified and directed. |
| 102 | Supply and fix polished Sadarahalli granite slab flooring 20 to 22 mm thick with grey cement slurry mixed with pigment to match the shade of the slab including 20mm thick screed bed in cement mortar 1:4 complete on staicase complete all as specified and as directed. |
| 103 | Petty repair to internal/external water inlet water pipe linecoming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removing the blockageincluding concealed water tubing etc of any height using scaffolding and and making the water supply functional complete all as specified and directed. |
| 104 | Supply and fixing 15mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed. |
| 105 | Supply and fixing 20 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed. |
| 106 | Supply and fixing 40 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing and connection complete all as specified and directed. |
| 107 | S&F in repairs of Stop Valve standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and as directed. |
| 108 | S&F in repairs of Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms) complete all as specified and as directed. |
| 109 | S&F in repairs of pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-110gms) complete all as specified and as directed. |
| 110 | S & F in repairs 15 mm dia stop valves of cast copper alloy fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and as directed. |
| 111 | S & Fin repair bib tap standard of PTMT any colour screwed for iron pipe and fixed,15 mm bore (minimum weight 90gms) complete all as specified and as directed. |
| 112 | S & F in repairs Bib taps cast copper alloy chromium plated fancy type screwed down screwed foriron pipe or for brass ferrule and fixed for 15 mm bore complete all as specified and as directed. |
| 113 | S & F in repairs pillar tap with capstan heads chromium plated fancy type screwed down high pressure with or withoutletter \"Hot\" or \"Cold\" with long screwed shanks and flynuts screwed for galvanised iron pipe and fixed complete for 15 mm bore complete all as specified and as directed. |
| 114 | S&F Rotational moulded polyethylene water storage tank of500 Ltrs capacity cylindericalvertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down old unserviceable tank complete all as specified and directed. |
| 115 | S&F PVC connections 15mm size with PTMT nuts of length 450 mm including taking down existing one complete all as specified and directed. |
| 116 | M&L Petty repairs to leaking water in bib taps, pillar cock, stop cock, angle valve, concealed stop valve, bottle trap of any description by changing thePVC washers/ Sheet washers,spindle brass,jumper brass or any other minor accessories (incl taking down and refixing) complete all as specified and directed |
| 117 | S & F in repairs viterous china wash down water closet (Pedestral pattern) EWC white incl plastic water closet seat cover and mild steel chromium plated or aluminium hinging device and connecting to \"P\" or \"S\" trap incl connecting flush pipe with flushing rim complete all as specified and as directed. |
| 118 | Supply and fixing in repairs plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed. |
| 119 | S&F in repairs grating doom 125mm dia with waste hole of Chromium plated (Min wt 40 gms) complete all as specified and as directed. |
| 120 | S&F in repairs Wash basin vitreous china (flat back or angle back type) size 580x400mm including taps wastechain and plug and porceline stopper but brackets including cutting for and pinning inends of brackets or erecting stand with waste pipe, complete all as specified and directed. |
| 121 | Taking down & re fixing high or low level flushing cistren 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of including rubber washers, syphon set, float valve, handle,fixing to wall clamp/bracket, stopping of leakage etc wherever required complete all as specified and as directed |
| 122 | S & F in repairs PVC low level flushing cistern 10 Lit capacity including necessary brackets incl connecting flush pipe etcand making good the disturbed surfaces complete all as specified and as directed. |
| 123 | S&F in repairs Vitreous China, half stall Urinal(back or corner wall type), complete including providing and fixing plugs, Urinal spreader, CP push cock, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipecomplete all as specified and as directed |
| 124 | S&F CP Concealed stop cock, Regular body with adjustable wall flange screwed down screwedfor iron pipe15mm bore.including taking down existing one complete all as specified and as directed. |
| 125 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed. |
| 126 | S&F Jaquar Rimeless Single PieceWC with PP Soft Close slim Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, suitable Size, S/P Trapand including all fittings complete fixed in repair, all as specified and as directed. (Make : Jaquar/ Parryware/ Hindware) |
| 127 | S &Fin repairs PVC connection pipe 15 mm dia, 600 mm long with check nut and bolt with washer complete all as specified and as directed. |
| 128 | S&F in repairs 40mm bore unplasticised PVC pipe of pressure rating 10 kgf/Sqcm fixed complete to walls, ceiling or laid in floors complete all as specified and directed. |
| 129 | S&F in repairs PVC waste pipe 32/40mm bore for WHB, Urinal & Sink complete all as specified and as directed. |
| 130 | S&F in repairs 40 mm Waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed one complete and all as specified and as directed. |
| 131 | S&F 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as specified and as directed. |
| 132 | M&L PCC (1:4:8) type D2 using 40mm graded aggregate 75mm thick as in sub base of floor finished even and rough to receive top layer all as specified and directed and demolition of old concrete (un reinforced) of any description and in anypositionnot otherwise specifically provided. |
| 133 | M&L in repairs 300x300x25mm thick prepolished cement concrete chequered tiles jointed in neat cement slurry and pointed in white or coloured cement to match the floor and including 20mm thick screed bed in CM (1:4) and incl removal of old and necessary demolition all as specified and directed. |
| 134 | Dismantling structural steel work incl doors, gates etcbut excluding framed trusses etc complete all as specified and directed. |
| 135 | S & F MS Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming toIS.1161-1979 grade St.-240complete all as specified and directed. |
| 136 | M & L Providing two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation of new steel surfaces all as specified and directed. |
| 137 | S&F Pre painted Coloured Galvalume roofing sheets 0.50 mm thick having Zinc aluminium alloy coatingdouble ribbed trapezoidal profile steel sheetany colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws and including dismantling of any type of old sheets in roof coverings complete all as specified & directed. |
| 138 | S&F inrepairsPre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws etc, including dismantling of old one complete all as secified and directed. complete all as specified and directed. |
| 139 | S&F in repairs 0.56 mm thick Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed. |
| 140 | M&L for welding in repairs not exceeding 10 Cm length & thickness of metal to be welded not exceeding 6mm complete all as spcified and directed. |
| 141 | Site clearance by Scraping of grass/wild growth/trees cutting n.exc 0.30m girth etc in soft/loose soil by manually/mechanically including removing of rubbish from the site to a distance exc, 250m but n. exc 500m and deposited where directed at a level not exc. 1.5m above the starting point, complete all as specified and as directed |
| 142 | M & L for 75 mm thick PCC type C1, 1:3:6 (20 mm graded stone aggregate) as in plinth protectionfinishing the surface even and smooth with using extra cement, including necessary demolition of old concrete all as speecified and as directed. |
| 143 | M & L precast cement concrete type B1 1:2:4 using 20 mm graded stone aggregate as in cover slabs for man hole and drain cover etc set in CM (1:6) complete all as specified and as directed. |
| 144 | M & L for TMT bars 6 to 8 mm dia & over cut to length bent to shape required incl cranking binding spirally for hooking for columns & binding with MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed. |
| 145 | Material and labour for keyed pointing in cement mortar 1:4 to random or polygonal rubble including racking out joints / points in cement mortar to squared rubble masonary coursed or un coursed etc complete, all as specified and directed. |
| 146 | M&L for cement plaster rendering 5mm thick in CM 1:3 on fair faces of brickwork or concrete surface as on ceiling finished even and smooth with thin layer and taking down cement plaster on ceilings surface etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed. |
| 147 | M&L preparation of newly plastered surfaces of ceiling and applying three coats of white washing on ceiling surfaces with smooth finish complete all as specified and directed. |
| 148 | M&Lin repairs Pre-cast PCC 1:3:6 type C1 (using 20 mm graded stone agg) cement concrete block masonry with solid blocks exc. 10cm in width and set in cement mortar 1:6 and demolition of old brick work / stone masonry/PCC block built in cement mortar of any description complete all as specified and as directed. |
| 149 | M&L for rendering 15mm thick in cement mortar (1:4) on brick or concrete surfaces of wall and finishing the surface even and smooth without using extra cement complete all specified and directed. |
| 150 | M&L Machine cut kota stone slab 20-25 mm thick as in flooring, laid over and incl 20 mm thick screed bed in CM 1:3 set and jointed in neat cement slurry and pointed with cement and pigment to match the shade of the slab incl rubbing and polishingcomplete all as specified and as directed. |
| 151 | Grinding of existing mozaic/kota stone/tiles in wall/flooring including mirror polishing, cleaning and joints filling and apply white cement complete all as specified and directed. |
| 152 | Supply and fixingAnodized aluminium size 605 x 605 mm snap grid frame work for false ceiling as per manufacturer instructions, with hangers of GI wire of suitable dia (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and6mm thick Non asbestos fibre cement building boards, fixed to sheet suitably placed in false ceiling grid made of Aluminium/G.I./ M.S.as per specification and drawing and including dismantling old unservicable ceiling board including frame of any type and description, complete all as specified and directed. |
| 153 | Material and labourfor Preparation of old decoratedplastered or unplastered surfaceof wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed. |
| 154 | Material and labourfor Preparation of old plastered or unplastered surfaceof ceiling, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applyingone coat of white wash complete all as specified and directed. |
| 155 | M&L for Preparation of old decorated surfaces of wallsby using pressure washer, remove all dirt & dust ,applying one coat of wall care putty and then applying two coats of premium oil bound distemper over one coat of primer as per manufauture instruction of required shade complete all as specified and directed. |
| 156 | Material and labourfor Preparation of old decoratedplastered or unplastered surfaceof wall, chajja, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applyingone coat of whitewashcomplete all as specified and directed. |
| 157 | M&L Preparation of old concrete/Asbestos/GI Sheet/Cement/Plaster surfaces overbrooming down or steel wire brushing down and applying one coat of synthetic enamel paintcomplete all as specified and as directed. |
| 158 | Taking down andre-fixing the same existing aluminium door/window/partitions (each shutter arean. exc 5sqm) after carrying out certain repairs as required, removing the existing beading and fixing new (i.e. including change of Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) rubber beading of suitable size with adhesive, overhauling of floor springs including repairing/cleaning/greasing etc and making the same fully functional all as specified and directed. |
| 159 | Supply and fixing in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixedportions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws,included rubber beading complete all as per architectural drawings and as directed. |
| 160 | Supply and fixing in repairs powder coated aluminium for shutters of window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, star lock, including rubber beadingcomplete all as per architectural drawings and the directions of Engineer-in-Charge. |
| 161 | S&F in repairs of aluminium anodised grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern(DG 104), with approved standard section and fixed to existing window frame with CP brass/stainles steel screws not less than 50mm and @ 200mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section ( 28mm x 19mm x 2mm thick) around the opening, complete as per site requirement and direction of EIC. |
| 162 | S&F 5 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50 Sqm in each pane complete all as specified and directed. |
| 163 | S&F 5 mm thick sheet glass ordinary quality and glazing complete in square exc 0.50 Sqm in each pane complete all as specified and directed. |
| 164 | Material and labourfor 12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, including side beading fixed with screws to Aluminium frame work complete all as specified and directed. |
| 165 | Supply and fixing 12mm thick Veneered particle board, solid core, exterior grade, with decorative face veneers for both faces, lamination, including side beading fixed with screws complete all as specified and directed. |
| 166 | S&F in repairs 12 mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required and glass fixing with fish mouth channel & patch fittings included as approved material, fixing with all accessories and glass joints should be filled with weather proof silicon including fixing to wall for all arrangments and opening push and pull arrangements for double door & for top and bottom for pivot and lock patch and including door floor spring automatic arrangements materials and fixing including, permanent fixing wall for all arrangement including fittings, complete all as specified and directedNote:- (a) Glass fixing to wall and opening arrangement necessary all fitting and screws included as directed by Engineer in Charge.(b) Glass fixing with fish mouth channel and glass joints should be filled with weather proof silicon, MS portal materials and fixing cost included as directed by Engineer in Charge.(c) The above cost included for double glass door opening (push and pull type) any size, including all materials and necessary fittings for all fixing arrangement. |
| 167 | S&F in repairs Stainless steel for glass door handles of size 400 mm, minimum 25mm dia, SS 304 and H type of approved pattern and make suitable for toughned glasscomplete all as specified and directed |
| 168 | Supply & Fixing of UPVC glazed 3 track-2 panel sliding windows with mesh made out of multi chambered uPVC sections with TPE gaskets having isolated drainage and reinforced with Galvanized iron profiles throught out the window. The outer frame having an overall size of 108 x 48 mm with reinforcement of 1.2mm thickness and sash with overall size of 38 x 61 mm with reinforcement of 1.2 mm thickness mesh sash of overall size 38 x 58mm Fiber mesh reinforced with 1.2 mm of GI. Glazing bead for fixing of glass shall be of size 16mm x 19mm and TPV gasket. Windows will be provided with 5mm thick plain float glass and stainless steel wiremesh, With \"Astrapia\" hardware or equivalent & Single point locking system of flush lock. Wall thickness of frame & sash shall be 2-2.2mm complete all as specified and directed. |
| 169 | Petty repair to aluminium section/glass doors, windows, ventilators, partitions and making good the same size upto 2 Sqm(i.e. including change of Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) included taking down and refixing complete all as specified and directed. |
| 170 | Supply and fixing in repairs 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 171 | Supply and fixing in repairs 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed. |
| 172 | Supply and fixing 100mm long Butt hinges medium weight cold rolledstainless steel, fixed in repair to wooden frame/welded to metal frame complete all as specified and as directed. |
| 173 | Supply and fixing in repairs butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed. |
| 174 | S&F in repairs floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed. |
| 175 | Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed. |
| 176 | Supply and fixing in repairs aluminium handles cast type anodised 150 mm long complete all as specified and as directed. |
| 177 | Supply and Fixing in repairs 250mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed. |
| 178 | S&F in repairs 250mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 179 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed. |
| 180 | S&F Aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed. |
| 181 | S&F 5mm thick rubber beading strips of entrance doors having width exc 3cm and not exc 5cm to arrest entry of insects including taking down existing one complete all as specified and as directed |
| 182 | Applying silicon sealent on joints of wall,cill jambs roof etc complete all as specified as directed |
| 183 | S&F in repair looking mirror of size 600mm x 450mm on commerical ply wood 6mm thick with PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass, screws and cup, washers, aluminium frame and fixed complete all as specified and directed. |
| 184 | M&L 25mm dia mild steel powder coated drapery rod cut to length required without joint in between and including mild steel powder coated fancy type brackets and fixed at openings including taking down existing one complete all as specified and directed. |
| 185 | S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed. |
| 186 | M & L for re-writing letters or figures (Block, Roman, Italic or Indian) n. exc 30 cm high and width, complete all as specified and directed. |
| 187 | S&Fin repairs manually operated polyester fabric roller venetian blinds of approved colour and pattern of any size and thickness of 0.45mm (+/-0.05mm) including high strength aluminium alloy extruded roller grooved tube having outer diameter 38 mm (=/- 0.05mm) and thickness 1.25mm (=/- 0.05mm) with ball chain pulley, ball chain including mounted projected aluminium brackets of powder quoted finish etc, screws and fixing, complete all as specified and directed. |
| 188 | Supply and fixing in repairs 7 feet 4 pipespulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm,made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit. Make Easydry or equivalent. |
| 189 | Supply and fixing for false ceiling as per manufacturer instructions, 10mm thick PVCinsulation panels with EPS stuck to 1mm printed PVC sheet , fixed to sheet suitably placed in false ceiling grid made of aluminium/G.I./ M.S.as per specification and drawing and including dismantling old unservicable wall and celing boardof any type and description, complete all as specified and directed. |
| 190 | Petty repair to renewing/matching glazed or ceramic coloured tilesin floors/walls in patches area not exceeding 5.00 Sqm including dismantling, removing and cleaning old tiles preparing beds and laying screed bed in CM 1:4 setting, jointing and pointing new or old tiles and joints filling and apply white cement and complete all as specified and directed |
| 191 | M&L Vitrified Ceramic tiles 10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding screed bed or bedding layer, 15 mm thick in Cement Mortar (1:6)complete including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed. |
| 192 | M&L Vitrified Ceramic tiles 10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over andincluding screed bed or bedding layer ,15 mm thick in Cement Mortar (1:4)complete including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed. |
| 193 | Material and labourfor 25 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in flooring surface as in level course etc including demolition of existing old cement concrete, including disposal of demolition material upto 500mtr from MD land complete all as specified and directed. |
| 194 | M & L for 100 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone agg) as in PCCin Hard standing etc.with , spike rolling ,or making impression of expanded metal, while the concrete is green complete all as specified and demolition of old concrete (un reinforced) of any description and in anypositionnot otherwise specifically provided. |
| 195 | Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside MOD land.NOTE :-Unit rate quoted shall also include for removal of PVC water storage tank and water pipe lines wherever existing carefully and refixing at the same or other position after completion of roof repair work |
| 196 | M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed. |
| 197 | Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with waters to remove dusts etc. complete all as specified and directed. |
| 198 | M&L for Brushing neat cement slurry with 3kg/sqm all as specified and directed. |
| 199 | M&L PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed. |
| 200 | M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with liquid WPC as per manufacturer instructions, complete all as specified and directed NOTE :- Integral WPC shall be measured and paid separately. |
| 201 | Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and as directed. |
| 202 | M&L APP polymeric membrane min weight 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm laid on primed surfaces by torch application method complete all as specified and directed. |
| 203 | M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces complete all as specified and directed. |
| 204 | Cleaning of air/dust blokages in the internal water supply lines concealed or fixed on the wall or floor surfaces by dismantling the fitting such as taps, valves, unions etc to facilitate/stimulate clearance of blockages/airlocks and re fixing the dismantled items after clearance of blockage/airlocks including fiiitngs etc complete all as specified and as directed |
| 205 | Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unsericeable steel/plastic/cpvc water tubing and connections complete all as specified and directed. |
| 206 | Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unserviceable steel/plastic/cpvc water tubing and connections complete all as specified and directed. |
| 207 | Supplying and fixing in repairs of 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified. |
| 208 | Supplying and fixing in repairs of 25mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified. |
| 209 | Supplying and fixing in repairs 20mm outer dia CPVC brass elbow all as specified and directed. |
| 210 | S&F Wash hand basin table counter type 560x400x200mm vitreous china (white) with cantilever CI/Angle iron bracketsembedded in concrete block, including long shank pillar tap, Brass chromium plated waste coupling 32mm bore, Waste pipe bottle trap, complete all as specified and as directed. |
| 211 | S&F in repairs of Swivel Shower with arm of PTMT any colour and 195mm long bend of 45 degree with flange for fixed with 15mm pipe(Minimum weight15mm-90gms) complete all as specified and as directed. |
| 212 | S&F in repairs 150 mm dia round/square grating of CP with or without hole includingJointed to PVC pipe complete all as specified and as directed.. |
| 213 | S & F in repairToilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screwsand complete all as specified and as directed. |
| 214 | S&F PVC body cabinet box mirror of size 350mm X 450mm X 100mmof PTMT alloy of approved pattern and design including taking down existing one complete all as specified and directed. |
| 215 | S&F 300mm arc size, 5mm thick corner glass shelf with stainless steel brackets, stainless steel railing in bathroom and fixed to wall with brackets including removing the existing fitting as required at site complete all as specified and as directed |
| 216 | S&F Towel Ring round including taking down existing one complete all as specified and as directed. |
| 217 | S&F in repairs Overhead Shower rose 125mm size (Brass Chrome Plated)complete all as specified and as directed. |
| 218 | S&F in repair Chromium platedsoap dishincluding fixing arrangement complete all as specified and directed . |
| 219 | S&F CP sink cock with swinging casted round shape spout screwed down screwedfor iron pipe in repairs 15mm bore including taking down existing one complete all as specified and as directed. |
| 220 | S&F Rotational moulded polyethylene water storage tank of1000 Ltrs capacity cylindericalvertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed. |
| 221 | Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe all as specified and directed. |
| 222 | S&F Angular stop cock, chromium plated valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking existing one complete as directed. |
| 223 | S&F in repairs Glass self assembly of 12mm thick andn exc 60cm length, 15cm wide with stainless steel brackets, stainless steel railing in bathroom and fixed to wall with brackets complete all as specified and as directed |
| 224 | S & F in repair tubular towel rail brass chromium plated 20 mm dia \"D\" type 60 cm long between flangescomplete all as specified and as directed. |
| 225 | Supply and fixing in repairs MS Mortise lock, 4 levers vertical type, size 100 mm for fixing to glass all as specified and directed. |
| 226 | M&L 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work including taking down old complete all as specified and as directed. |
| 227 | S&F Decorative laminates of 0.90 mm thick fixed with approved adhesive type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed. |
| 228 | S&F Continuous (piano) hinges, stainless steel bright finish or electrogalvanised of 40mm width of flaps (when open) complete including taking down old one all as specified and as directed. |
| 229 | S&F Magnetic catches with 8mm dia steel ball and brass body and striking plate including taking down existing one complete all as specified and directed. |
| 230 | S & F in repair 18/19 mm thick ,water proof plywood , fixed to Cupboard work in any position with nails including removal of old boards of any description complete all as specified and as directed. |
| 231 | S&F PVC beading for cupboard work, colour and pattern as approved including taking down existing one complete all as specified and as directed |
| 232 | S&F Stainless steel spring hinges of size of approved pattern and make suitable for base/wall unit of modular kitchen including taking down the existing one complete all as specified and directed. |
| 233 | S&F Stainless steel handles of size 150 mm of approved pattern and make suitable for Base/Wall unit of modular kitchen including taking down the existing one complete all as specified and directed. |
| 234 | S&F Stainless steel plain basket of size 530 x 505 x 100mm including taking down the existing one complete all as specified and directed. |
| 235 | S&F Stainless steel thali basket of size 600x 500x 100mm including taking down the existing one complete all as specified and directed. |
| 236 | S&F Stainless steel bottle basket of size 200x 508x 431mm including taking down existing one complete all as specified and directed. |
| 237 | S&F Stainless steel cutlery basket of size 530 x 505 x 100 mm including taking down the existing one complete all as specified and directed. |
| 238 | S&F Stainless steel telescopic slider of 500 mm size of approved pattern and make suitable fordrawer in base unit of modular kitchen including taking down the existing one complete all as specified and directed. |
| 239 | M&L Granite 18 to 20mm thick (table rubbed and polished) in steps,Jamps, Pillars, Windows, cills, platforms and like CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade of Granite over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) all as specified and as directed. Note :(i)The Unit rate quoted is included for demolition of old Stone Slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.(ii)Cost of rounding of stone deem to be included in unit quoted rate. |
| 240 | Petty repair to wall mixer,basin mixer,sink mixer etc including replacement of spindle brass, Jumper brass, rubber washer, head incl taking down and refixing ete all as specified and directed |
| 241 | S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipecomplete all as specified and directed. |
| 242 | S&F in repairs CP 2 way bib cock with wall flange fancy type screwed down screwedfor iron pipe in repairs 15mm bore complete all as specified and as directed. |
| 243 | Petty repairs to refixing the existing Wash hand basin and Sinks made of stainless steel 1mm thick kitchen flat back with including fixing cantilever CI/Angle iron brackets embedded in concrete block including connecting waste coupling 32mm bore, including bedding, waste fitting, waste pipe in cement mortar to dwarf wall and connecting union to pipe, filling gap in white cement and all necessary fittings to fixed in repair(including taking down and refixing in same position) complete all as directed. |
| 244 | S&F Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall orincluding fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairsall as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA. |
| 245 | S&F Plate rack of size 65 cm x 96 cm (heavy duty) made of stainless steel fixed in repairs complete all as specified and directed. |
| 246 | Dismantling the existing unservicible gully trap including chamber and material and labour for provision of new salt glazed stoneware gully trap, square or round mouth type \"P\" of size 180X150mm, including setting and jointing in cement mortar 1:1 in chamber with plain cement concrete base in PCC 1:2:4 type B1, brick work in cement mortar 1:4, rendering in cement mortar 1:4, all around finished even and fair using extra cement, Precast cover slab in RCC 1:2:4 type B1 using 20mm graded stone aggregates, reinforcement with 8 mm diain both ways etc, including provision of handle etc complete all as specified and as directed. |
| 247 | Note :- An amount of Rs 1,36,525.00 on account of credit schedule for schedule \"A\" part II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
