Tender For Construction Of New Godown (250 Mt) And Renovation Of Godown (500 Mt)=2 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m.beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering Including shoring and strutting etc. complete. (LIFT UPTO 1.5 M.) By Mechanical Means(PWD S.S.R. 22-23 Item Serial No.721 & Item No.21.02/Page-153) 3 Excavation for foundation in Hard murum in cluding removing the excavated material upto adistance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means (PWD S.S.R. 22-23 Item Serial No.725 & Item No.21.06/Page-153) 4 Excavationforfoundationinhardmurum andbouldersincludingremovingtheexcavatedmaterialup toa distance50metres,beyondthebuildingareaandstackingandspreadingasdirected,dewatering, preparingthe bedforthefoundationandnecessarybackfilling,ramming,wateringincludingshoring andstruttingetc. complete.(Lift upto1.5m.)ByMechanicalMean 5 Providing and laying Cast in situ/ Ready Mix cement concrete in M-10 of trap/granite/quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete ,with fully automatic microprocess or base dPLCwith SCADA enable dreversible Drum Type mixer/ concrete Batch mix plant (Panmixer) etc.complete. With fine aggregate (Crushed sand VSI Grade) (PWD S.S.R. 22-23 Item Serial No.827 & Item No.24.01/Page-175) 6 ProvidingsecondclassBurntBrickmasonrywithconventional/I.S.typebricksincementmortar1:6 in foundationsandplinthofinnerwalls/inplinthexternalwallsincludingbailingoutwatermanually, strikingjoints onunexposedfaces,rakingout joints onexposedfacesandwateringetc.Complete. 7 Providing and laying in situ cement concrete of M-20 grade of trap / granite/quartzite/gneiss metal for R.C.C. worklike raft, grillages, strips, foundations and footings of R.C.C.columns and steel stanchions including bailing-out water manually, including centering formwork of plywood / steel, compaction, covering newly laid concrete by gunny bag, plastic or tarpaulin, finishing the formed surface with cement morter 1:3 of sufficient minimum thickness to give a smooth and even surface or rougheningif special finish is to be provided and curing etc complete. (Excludingreinforcement) The cement mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. (Wooden planks / shuttering will not be allowed) Spec.No.:Bd.F.2 Page No. 298 /IS 456 (1978) (PWD S.S.R. 22-23 Item Serial No.836 & Item No.25.11/Page-178) 8 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (PWD S.S.R. 22-23 Item Serial No.841 & Item No.25.31/Page-179). 9 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (PWD S.S.R. 22-23 Item Serial No.846 & Item No.25.50/Page-181). 10 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/granite/quartzite/gneiss metal for R.C.C.slabs and landings as per detailed designs and drawings including steel centering,formwork,coverblocks,laying/pumping,compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc.complete,(Excluding reinforcement and structuralsteel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Panmixer) etc.complete.With fine aggregate (Crushed sand VSI Grade) (PWD S.S.R. 22-23 Item Serial No.851 & Item No.25.70/Page-182). 11 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (PWD S.S.R. 22-23 Item Serial No.871 & Item No.26.33/Page-188). 12 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. (PWD S.S.R. 22-23 Item Serial No.897 & Item No.27.05) 13 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (PWD S.S.R. 22-23 Item Serial No.963 & Item No.32.11/Page-209). 14 Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.(PWD S.S.R. 22-23 Item Serial No.961,966. & Item No.32.07/Page-209 & Item No.32.15/Page-210). 15 Providing and applying white-wash in three coat on old / new plastered or masonry surface sand asbestos cement sheets including scaffolding and preparing the surface by brushingand brooming down etc. complete.(PWD S.S.R. 22-23 Item Serial No.1097, 1098. & Item No.36.02/Page-227 & Item No.36.03/Page-227). 16 Providing & applying waterproof cement paint three coats on plastered or masonary surface of approved manufacturer and of approved colour including primer coat scafolding & preparing the surface watering for two days complete. (Bd.O.8/406).(PWD S.S.R. 22-23 Item Serial No.1085 & Item No.35.15/Page-224). 17 Providing and fixing rolling shutter fabricated from steell at hsofminimum thickness 0.9mm with lock plate of 3.15 mm thickness reinforced with 35x35x5mm angle section fitted with sliding bolts and handles for both sides, deep M.S.channel section of depth and thickness not less than 65mm and 3.15mm respectively with hold fastarr angements, M.S.Bracket plate 300x300x3.15mm minimum size and shape with square bar, suspension shaft of minimum 32mm diameter, hood cover of M.S. sheet not less than 0.9mm thickness and of any size attopand safety device sincluding mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade castir on or mild steel and one coat of redlead primer etc. complete.(I.S.62481979) (Without mechanical gear)(PWD S.S.R. 22-23 Item Serial No.1217 & Item No. 39.24/Page-248). 18 Providing and fixing steel window of various sizes as per detailed drawing without hotdip zinc coating, with out ventilators, including fabricating/ glazing with plain/ obscured glass panels of approved type and quality, iron oxidised fixtures and fastenings, finishing with oil painting two coats complete (with guard bars12 mm square at 10 cm c/c.). (PWD S.S.R. 22-23 Item Serial No.1223 & Item No.39.30/Page-249) 19 Providing structural steel work in trusses,other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2coats of oil paintingapproved quality and shade etc. complete. (PWD S.S.R. 22-23 Item Serial No.819 & Item No. 23.04/P.no.819) 20 Providing and fixing colour coated Zincalume(R) AZ150 (min150gms/sq.mt.total on each side) profiledsheets for roofing. The feed material is manufactured out of nominal 0.45 mmBase Metal Thickness (BMT)(0.5mmTCT), Hi-strength steel with min.550 MP a yield strength, metallic hot dip coated with Aluminium-Zincalloy (55%aluminium 43.4% zinc1.6% silicon) with COLORBOND (R) steel quality super durable polye ster paint coat (with in organic pigment). The paint shall have a total coating thickness of nominal 35um, comprising of nominal 25 um exterior coat on top surfaceandnominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050mm effective cover width and nominal 25-30mm deep ribs with subtle square fluting in the five panat nominal 180-250mmcenter-to-center.Theend rib shall be designed for anti-capillary groove. and return leg.The feed material should have coil manufacturers product details marke daregular interval .Including fastenerswith min.fastened with min.25umZinc-Tin alloy coated, Hexhead,self-drillings crew etc.complete. (weight of profile 4.52 Kilogram/ One Square Metre) (PWD S.S.R. 22-23 Item Serial No.1174 & Item No. 38.34/P.no.236) 21 Providing and fixing wind oppareted tarbo ventiletar systim (24 inch dia.) over exsiting roof including cutting of sheet ,propar fixing in position to true line & level with all fixtures & fastning, providing 0.8mm thick FRP sheet for covering area between roof and fan so as to provide waterfoof joints with approved water proffing compound making good the roof surface including cleaning etc. complete (General application for all types of roofs for ventilation & day light parpose at terrace[As directed by Engineer in charge]. (PWD S.S.R. 22-23 Item Material list & Item No.42/P.no.529) 22 Filling in plinth and floors with contractors material/ brought from outside and approved by Engineer in charge in layers of 15 cm to 20 cm including watering and compaction etc.complete. (PWD S.S.R. 22-23 Item Serial No.751 & Item No.21.37/Pa.no.157). 23 Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.(Providing & laying stone metal layer of 20 cm thickness with 60 mm over size metal 65% and 40 mm size metal 35% with sand or stone chips spreading & leveling handpacking complete.[Rd.22/201,Rd.20/200 &Rd.20/205 ]) 24 Providing and laying in situ cement concrete M20 with tremix treatment for 100 mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumenetc. complete.(PWD S.S.R. 22-23 Item Serial No.1017 & Item No. 33.30/Page-216) 25 Warehouse Electrification 26 Supplying & erecting mains with 2x1.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire, in HMS PVC conduit min. 20mm dia.CSR 2022-23 Item No 1-3-1/5Additional specification No: WG-MA/PC. 27 Supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia.CSR 2022-23Item No 1-3-2/5Additional specification No: WG-MA/PC. 28 Supplying & erecting mains with 2x4 sq.mm. and earth wire 2.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia,CSR 2022-23 Item No 1-3-3/5Additional specification No: WG-MA/PC. 29 Supplying and erecting Ceiling rose / Batten holder / Slanting holder / hanging cord switch / hanging bell push / pendent holder bakelite base 6A. erected on filled polypropylene board or polished double wooden block/ PVC junction box.CSR2022-23Item No 1-5-7/7 30 Supplying and erecting hylam sheet/ ebonite sheet 3 mm thick for covering wall entries including cutting, drilling and fixing with nut bolts / screws etc. complete. CSR 2022-23 Item No 6-1-9/106 31 Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted suitable for SPMCB of 12 ways on iron / GI frame (horizontal busbar type)CSR2022-23 Item No 5-4-1/91Additional specification no. SW-SWR/MCBDB 32 Supplying, erecting & marking FPMCB 63A in provided distribution board. CSR 2022-23 Item No 5-3-16/91 Additional specification No. SW-SWR/MCB 33 Supplying, erecting & marking DPMCB 6 A to 32 A B- series (for lighting) in provided distribution board. CSR 2022-23 Item No 5-3-7/90 Additional specification No. SWSWR/ MCB 34 Supplying & erecting conventional spike Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results. CSR 2022-23Item No 9-1-3/160Additionalspecification No. EA-EP 35 Supplying, erecting & terminating XLPE armoured cable 4 core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe.CSR 2022-23 Item NO 7-1-30/128 Additional specification No CB-LT/AL 36 Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. CSR 2022-23Item No 7-6-10/140 37 Supplying & erecting Siemens type brass cable glands for 4 core 35 sq. mm./3 core 50 sq. mm. for XLPE armoured cable. CSR 2022-23Item No 7-7-4/141Additional specification No. CB-GL 38 Supplying & erecting crimping type copper lugs for cable 25 sq. mm. complete.CSR 2022-23 Item No 7-9-2 / 142 Additionalspecification No. CB-CL/CU 39 Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 2 ways for outgoing SPMCBs on iron/ GI frame. CSR 2022-23Item No 5-4-1/91Additional specification No. SW-SWR/MCBDB 40 Supplying and erecting LED Street light fitting suitable for above 40W to 48W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete .CSR 2022-23Item No 2-5-4 /28Additional specification No . FGODF/ FLS2. 41 Supplying and erecting Street light bracket made from 40 mm. dia ‘B’ class G.I. Pipe, 0.6m. in length along with pole cap of 300 mm length and 80 mm dia duly welded with provided leads. CSR2022-23Item No 2-7-2 /32Additional specification No. FG-BKT/BPC 42 Providing and fixing copper strip 25mm wide and 3mm thick for lightening conductor including fixing with screws required scaffolding etc.complete Note- Lightening conductor and earthinf pits is not considered in this item. PWDSSR2022-23 Item No 44.19 / 595 Additional Spec No :BDW 1 Page No 581 & As directed by Engineer in Charge 43 Warehouse Renewation 44 Dismantlingbrickmasonryincementmortorandstackingthematerialas directedwith all l eads, lifts etc. complete. 45 RemovingG.I. sheetfromroof orceiling and stackingthemas directedwithall leadsand lifts etc. complete 46 Removingothertypetrussbelow 5 metresspanfromroofandstacking the materialsas directedwithallleadsandliftsetc. complets 47 Removingcementtiles, ormarbleorpolishedshahabadfloor ordado withoutbed concrete including stacking the materials as directed with all leads, lifts etc. complete 48 Removingdoorsandwindowswithframes and stackingthematerialsasdirected with all leads, lifts etc. complete. 49 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. (PWD S.S.R. 22-23 Item Serial No.897 & Item No.27.05) 50 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (PWD S.S.R. 22-23 Item Serial No.963 & Item No.32.11/Page-209). 51 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:3 without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete.(PWD S.S.R. 22-23 Item Serial No.958 & Item No.32.04/Page-209). 52 Providing & applying waterproof cement paint three coats on plastered or masonary surface of approved manufacturer and of approved colour including primer coat scafolding & preparing the surface watering for two days complete. (Bd.O.8/406).(PWD S.S.R. 22-23 Item Serial No.1085 & Item No.35.15/Page-224). 53 Providing and fixing rolling shutter fabricated from steell at hsofminimum thickness 0.9mm with lock plate of 3.15 mm thickness reinforced with 35x35x5mm angle section fitted with sliding bolts and handles for both sides, deep M.S.channel section of depth and thickness not less than 65mm and 3.15mm respectively with hold fastarr angements, M.S.Bracket plate 300x300x3.15mm minimum size and shape with square bar, suspension shaft of minimum 32mm diameter, hood cover of M.S. sheet not less than 0.9mm thickness and of any size attopand safety device sincluding mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade castir on or mild steel and one coat of redlead primer etc. complete.(I.S.62481979) (Without mechanical gear)(PWD S.S.R. 22-23 Item Serial No.1217 & Item No. 39.24/Page-248). 54 Providing structural steel work in trusses,other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2coats of oil paintingapproved quality and shade etc. complete. (PWD S.S.R. 22-23 Item Serial No.819 & Item No. 23.04/P.no.819) 55 Providing and fixing colour coated Zincalume(R) AZ150 (min150gms/sq.mt.total on each side) profiledsheets for roofing. The feed material is manufactured out of nominal 0.45 mmBase Metal Thickness (BMT)(0.5mmTCT), Hi-strength steel with min.550 MP a yield strength, metallic hot dip coated with Aluminium-Zincalloy (55%aluminium 43.4% zinc1.6% silicon) with COLORBOND (R) steel quality super durable polye ster paint coat (with in organic pigment). The paint shall have a total coating thickness of nominal 35um, comprising of nominal 25 um exterior coat on top surfaceandnominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050mm effective cover width and nominal 25-30mm deep ribs with subtle square fluting in the five panat nominal 180-250mmcenter-to-center.Theend rib shall be designed for anti-capillary groove. and return leg.The feed material should have coil manufacturers product details marke daregular interval .Including fastenerswith min.fastened with min.25umZinc-Tin alloy coated, Hexhead,self-drillings crew etc.complete. (weight of profile 4.52 Kilogram/ One Square Metre) (PWD S.S.R. 22-23 Item Serial No.1174 & Item No. 38.34/P.no.236) 56 Providing and fixing of colour coated Zincaluminium( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. Ridge.The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated withAluminium-Zinc alloy (55% aluminiumm 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyster paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 mm, comprising of nominal 25mmexterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950- 1050 mm effective cover width and nominal 25-30 mm deep ribs with sublet square fluting in the five pan at nominal 180-250 mmcenter- to-center. The end rib shall be designed for anti-capacity groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. including fasteners with min.fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre) 600 mm girth (Surface Width).(PWD S.S.R. 22-23 Item Serial No.1175 & Item No. 38.35/P.no.237) 57 Providing and fixing wind oppareted tarbo ventiletar systim (24 inch dia.) over exsiting roof including cutting of sheet ,propar fixing in position to true line & level with all fixtures & fastning, providing 0.8mm thick FRP sheet for covering area between roof and fan so as to provide waterfoof joints with approved water proffing compound making good the roof surface including cleaning etc. complete (General application for all types of roofs for ventilation & day light parpose at terrace[As directed by Engineer in charge]. (Jalgaon D.S.R.304 /123) 58 Providing and laying in situ cement concrete M20 with tremix treatment for 100 mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumenetc. complete.(PWD S.S.R. 22-23 Item Serial No.1017 & Item No. 33.30/Page-216) 59 TRUCK Pointing for ucr masonaryProviding tuck pointing with cement mortar 1:3 for stone/Brick masonry including scaffolding and curing etc. complete. 60 Warehouse Royalty 61 Sand 62 Murum 63 RUBBLE 64 Warehouse Testing 65 Comp. Strength- Cube 66 Cement-Fineness,consistency.Setting time,Compressive strength,Specific Gravity 67 Sand-Fineness Modulus,Silt Content 68 Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks). 69 Murum In PlinthPlasticity Index 70 STEEL Tensile strength Yield stress, ultimate tensile stress. %elongation, weight per running meter,Bend/Rebend test. (Set of 3 Bars)UP to 16mm 71 M20 Cement Concrete Mix Design (With all Tests on basic materials) 72 Management Strategies and Implementation Plan (MSIP) to manage the Environmental, Social, Health and Safety (ESHS) risks and ESHS Code of Conduct
