|
| 1 | Clearing grass and removal of rubbish maximum 150mm thickness & dispose off up to a distance of 100 Meter outside the periphery of the area by manual means. |
| 2 | Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 meters, stacking serviceable and unserviceable materials separately as per MoRTH specification clause 202.By Mechanical Means :Bituminous courses |
| 3 | Construction of sub grade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to require slope and compacted by vibratory roller 8-10 Tonne to meet requirement of Table 300-2 as per MoRTH specification Clause No. 305. |
| 4 | Providing and laying granular sub-base material having P.I. not more than 6 including spreading in layers not exceeding 150 mm compacted thicknessand consolidation by 8-10 tonne power rollerto required camber and grade including cost of water and hire charges of machinery including T&P with all lead (Compacted thickness to be measured).as per MoRTH specification table 400-1, 400-2,(For Grading I Material) |
| 5 | Providing and fixing of Precast concrete interlocking blocksof 60mm thick manufactured from fully computerized automatic stationery hydraulic vibro pressed machine & fullcomputerized automatic batching plant of class as per IS: 15658-2006. The C.C. interlocking paving blocks be laid onaverage 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub base as defined. The work includes earth work in cutting of B/T road, cutting of WBM road and disposal of unserviceable material with all leads & lifts and stacking of serviceable material complete job is to be executed as perthe instructions of Engineer-in-charge. The rates to be inclusive of all lead, lifts & taxes General specification of Blocks:80mm thick, Medium traffic category,80MM M40 Grade designation blocks |
| 6 | S & F cement concrete pre cast Kerb or Dand up to 60 cmlength over 20 mm thick base of cement mortar1:4 including jointing earth work, pointing & jointing with cement mortar 1:4 of size Including cost of M- 20 Mix Dand/Kerb (20 x 25)/2 x 30 cm |
| 7 | Providing, laying, spreading and compactingstone aggregate forWet Mix Macadam (as per table 400-12 and 400-13) specification including premixing the material with water to OMC in wet mix plant as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/Front end Loader/paver finisher, in sub base/ base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintenance of diversion etc. (MoRTH specification : Clause 406 & Clause 112)by mechanical means with all lead . |
| 8 | Providing and applying primer coat over prepared surface or granular base with bitumen emulsion SS-1 as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 Sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI 502 & 112 (Including cleaning of road surface ) |
| 9 | Add extra to item No. 5.1 for 1 Kg / 10 Sqm emulsion |
| 10 | Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 500-8 & 500-10 and design mix for base/binder course including loading of material with Front end loader, heating of binder (including cost of anti-stripping compound wherever required) aggregate and filler as per table 500-9,in hot mix plant More than 60-90 TPH, transporting the mixed material by tippers and laying with sensor paver finisher as per clause 505.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 505 & 112] with all leadsGrading II (26.5mm nominal size) - Bitumen @ minimum 4.5% of mix usingVG 30( thickness 50 - 75 mm ) |
| 11 | Providing and applying tack coat on the prepared surface, withbitumen emulsion RS-1 as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification Clause 503 & 112 ( Including cleaning of bituminous road surface ) |
| 12 | Add extra to item No. 5.2 for 1Kg / 10 Sqm emulsion |
| 13 | Providing and laying bituminous concrete as per design mix on preparedsurface with specified graded stone as per table 500-16 & 500-17 for wearing course including loading of aggregate with Front end loader and hot mixing of binder (including cost of anti-stripping compound, wherever required) and filler as per table 500-9 with aggregates in hot mix plant More than 60-90 TPH Transporting the mix material with tipper and laying with sensor paver finisher (as per clause 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MoRTH Specification : Clause -507 & 112) with all lead.Grading II (13.20 mm nominal size) - Bitumen @ minimum 5.40% of mix & thickness 30 - 40 mm (VG-30). |
| 14 | Providing and laying marking of center line and stop line etc with hot thermoplastic compound of approved qualitywith type-1 glass beeds (Table-800-9), 2.5 mm thick on road/ plain surface, including reflectorising glass beads type-2 (Table-800-10) @ 250 gms per sqm area with special applicator machine, as per IRC:35 including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control involved. The finished surface to be level, uniform and free from streaks and holes as per clause 803 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. (Edge Line ) |
| 15 | Centre Line |
| 16 | Raised Payment Marker (Cats Eye): Supplying and Fixing of Molded Shank Raised Pavement Markers made of ABS Moulded body and Polycarbonate Reflective panels with Micro Prismatic Lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 35000 Kilogram tested in accordance to ASIM D 4280 & ASTM D 788. The Height of Road Stud is 20mm, Width 100mm, Length 100mm and minimum reflective area of 13 sqcm on each side.The Strength of detachment of the integrated cylender shank not less than 14+/-2mm (Thickness) and height not less than 30+ 2mm from the body. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive |
| 17 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, coarse aggregate 26.5mm nominal size aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. as per MoRTH Specification cl. 601. |
| 18 | Supplying and fixing pre cast R.C.C. stones (M-15 mix) using one percent steel reinforcement, including finishing in cement sand mortar 1:3, earthwork, cement concrete 1:4:8 engraving letters and numerals, painting with enamel paint etc. complete as per IRC standard design.Km. Stone for NH, SH & MDR ( size 35 x110x25 cm) Km Stone |
| 19 | 200 Meterstone( size 15 x10x65 cm) |
| 20 | Supply of village Name Board size 600x900 mm made out of 1.25 mm thick M.S. sheet duly framed with 30mm Outer Dia Mild Steel tube tightened with M.S. flat 12x3 mm fixed on two posts of size 40 mm ODMS tube 3M long whole board is processed in blue/white stoving enamel paint and white/red machine cut reflective sheet complete in all respect posts duly painted with black/white synthetic enamel. |
| 21 | Supply of Chevron sign of size 75x60 cm made out of aluminum sheet 2 mm thick with fixing provision on M.S. angle iron post 50x50x6 mm 3 M long screwed with stainless steel nut bolts of 8 M dia, plate is covered by high intensity grade yellow retro-reflective sheeting and black screen printed arrow on Retro Reflective Sheet, complete in all respect. Comp. in all respect duly post painted in alternate band of Black/White synthetic enamel paint & hold fast at bottom. |
| 22 | Fixing of sign board having two posts including excavation cement concrete 1:5:10(30X30X60 cms.)and transportation complete of size. :60x75 cm, 90x60 cm, 75x45 cm, & 60x45 cm. (Village name and Chevron sign fixing ) |
| 23 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (90 cm equilateral triangle) Pedestrain crossing,school ahead signs. (14 Pedestrian crossing signs and 8 school ahead signs) |
| 24 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (60 cm circular) Speed limit sign board. |
| 25 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing (90 cm high octagon) Stop Sign |
