Tender For Provision Of Certain B/R And E/M Minor Works At Af Station Bareilly Under Ge (Af) Bareilly.; 1 B&R PORTION :Excavation in trenches not exc 1.50 mtr wide and not exc 1.50 mtr in depth for foundation etc or for shafts, wells, cespits, manholes, pierholes etc not exc 10 Sqm on plan and getting out in soft / loose soil all as specified. 2 All as per item No.2.00 above butexc 1.50 mtr and and not exc 3.00 mtr in depth. 3 Removing excavatedmaterial (soil)to a distance not exc 50 meter and depositing where directed at a level not exc 1.5 mtrr above from the starting point and deposited where complete all as specified. 4 Returning, filling in including spreading, levelling watering and well ramming in layer not exc 25cm thickcomplete all as specified. 5 M&L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified. 6 M & L for cement concrete type D-2, 1:4:8 mix (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete ,sub base floor complete all as specified. 7 M&L for brick work with sub-class `B bricks, straight or curved on plan exc6.0 mtr mean radius and built in cement mortar 1:6 all as specified. 8 M & L for loose filling with aggregate of gauge 40mm to 80 mm broken bricks in soakage pits, soakage wells, sunkan floor etc all as specified. 9 M&L for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs suppoted on walls, beams and column in floors, roofs, landings, canopies, deck slabs and in shelves complete all as specified. 10 M&L for formwork to sides , soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete all as specified. 11 M&L for mild steel TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. 12 M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces including finishing surfacefair and even without using extra cement complete all as specified. 13 M&L for 150 mm dia reinforced concrete pipes, class NP-2, laid and jointed complete with collors in trenches and jointed in cement mortar 1:1 with spun yarn all as specified. 14 M&L for cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipeafter they are laid and tested all as specified. 15 Surface excavation notexceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified. 16 M&L for 100 mm thick cement concrete type D-2, 1:4:8 mix (using 40mm graded stone aggregate) as in sub base complete all as specified. 17 M&L for150 mm thick cement concrete 1:2:4, type B-2 (using 40 mm grade stone aggregate) as in floor finishing top surface even and smooth without using extra cement all as specified. 18 M&L for cement concrete type B-1,1:2:4using 20 mm graded stone aggregate inin lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings,hold fast,kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work all as specified. 19 M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240 all as specified. (Note :- All structural member including tubular truss should be mechanically curved all as directed by Engineer-in charge and the quoted rate deemed to be included in the item) 20 M&L for plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections conforming to Fe 410W (Gde E-250) quality-A complete all as specified. 21 S&F for pre-painted galvalume aluminum zink coating GI based corrugated steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self coaching screwas specified. (Note:- Colour and design as approved by Engineer-in-charge) 22 M&L for preparation of newly steel and iron surfaces of any description not exc 10 cm in width or grith, not otherwise describedand applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer complete all as specified. 23 Supply only liquid water proofing compound all as specified. 24 M&L forpreparation of newly plastered surface of wall and applying two coats of cement base paintall as specified. 25 M&L for 15 mm thick rendering in cement mortar 1:6 on fair face ofbrick work or concrete surfaces including finishing surface even and smooth without using extra cement all as specified. 26 M&L for 75 mm thick cement concrete type C-1, 1:3:6 (using 20 mm gradedstone aggregate) as in plinth protectionlaid in bay not exc 3.00 Sqm each including finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with bitumen mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified. 27 S&F for non skid coloured ceramic tiles 400 mm x400 mmx 7 to 8 mm thick as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile laid over 15 mm thick screed bed in cement mortar 1:6 all as specified. 28 M&L for glazed ceramic coloured/printed tiles 350 mm x 250 mm x 7 mm/ 450 mm X 350 mm X 7 mm thick as on vertical surface such as skirting, dado, wall etc, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tile over 10 mm thick rendering in cement mortar 1:4 all as specified. 29 S&F for vitreous china wash down water closet pan(Pedestal pattern) white including white plastic seat coverclosed pattern with flat bottom and cover and mild steel chromium plated hinging device all as spedcified. 30 S&F for vitreous china wash basin, Oval type, snow white, flat back of size 560mm x 400mm over and including 18 to 20 mm thick Z black granite stone slab (table rubbed and polished) including bull nosed as on shelves for cooking plateform/ WHB /pillars etc over and including 20 mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white /coloured cement to match the shadecomplete all as specified. (Granite slab shall be measured & paid for separately) 31 S&F fortoilet paper holder,chrome plated, box type , fixed to walls with chromium plated brass screws complete all as specified. 32 S&F for PVC waste pipe 900mm long with threaded cup suitable for 32mm dia couplings for urinals and wash hand basins complete all as specified. 33 S&F for 32mm dia waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified. 34 S&F for PVC low level flushing cistern white 10 Litres capacity, valve less, with inlet, ball valve, float and handle including brackets, PVC flush bend pipe etccomplete all as specified. 35 S&F forchromium plated health faucet with hand shower & flexible cord suitable for EWC including fixing to steel pipe or union of 15 mm bore dia, (Health Faucet) with 8 mm dia 1.2 Mtr long flexible tube & wall hook) complete all as specified. 36 S&Ffor 15mm dia stop valve / angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or forunions and fixed but fancy type chromium plated with long shank and cup all as specified. 37 S&F for PVC connection 45 cm long with two nuts and washers complete all as specified. 38 S&F for 15 mm dia two way bib taps, chromium plated with fancy type, long bodywith screwed down, screwed for iron pipe all as specified. 39 S&F for 15 mm bore chromium platedpillar taps, cast copper alloy, with captan head screwed down high pressure with or with out lettred Hot or Cold with long screwed shanks swan neck and fly nut screwed for iron pipe or for brass ferrule. 40 S&F for CP greating125 mm dia with or without hole to match the colour of floor tile all as specified and directed. 41 S&F for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified 42 S&F for 900 mm x 450 mm size bevelled edge mirror of selected quality glass mounted on 6mm thick commercial plywood and fixed to wooden plug with chromium plated brass screws and cup washers. 43 S&F for tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated complete fixed to walls. 44 S&F for rotational moulded polyethylene water storage tanks three layers (Cylindrical vertical with closed top) of 500 ltrs capacity hoisted and fixed in position all as specified and directed. 45 S&F forPVC ball cock, 20 mm bore high pressure of PTMT eppoxy coating aluminium rod with polythene float and flynut complete, screwed for iron pipe all as specified. (Min wt 210gm ) 46 S&F for20mm bore Gun-metal, glove or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed all as specified. 47 S&F for 110 mm bore PVC (SWR) pipes , single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. 48 S&F for 75 mm bore PVC (SWR) pipes , single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. 49 S&F 110 mm borePVC (SWR) bendall as specified. 50 S&F 110mm borePVC (SWR) heel rest bend of any radius complete all as specified. 51 S&F 75mm bore PVC (SWR) bends of any radius with access door complete all as spd and directed. 52 S&F 75 mm borePVC (SWR) heel rest bend of any radius complete. 53 S&F for PVC (SWR) vent cowl for 75 mm bore pipe. 54 S&F for grating doom 125 mm dia with waste hole of PTMT.(Minimum weight 40gms) all as specified. 55 S&Ffor 75 mm dia PVC (SWR) floor trap long neck type with greating including jointing with solvent cement all as specified . 56 All as per item No. 11.00 above but for 8 mm dia and over upto and including 10mm dia in stirrups, spaces and binder etc complete all as specified. 57 M&L for reinforced cement concrete 1:2:4 mix, type B-1 using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.50 mtr span and the like complete all as specified. 58 M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified. 59 S&F for 20mm thick granite stone slab machine cut,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 20 mm thick screed bed or bedding layer of cement mortar (1:4)for laying floor finishes, chamfering/ bull nosing of edges and grinding and polishing complete all as specified and as directed. 60 S&F for cutting chasing, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chasing for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth andall as specified and directed. 61 M&L for cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings,etc or cutting out defective brick work for under pinning, including providing fixing and removing the debris from site to outside MoD land. 62 M&L for forming jambs in cement mortar 1:6 to openings( to foregoing item No above ) including cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work complete all as specified anddirected. 63 S&F for 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified. 64 S&F for 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified. 65 S&F for brass elbow (3/4 inch X ½ inch) 66 S&F for brass tee for 20mm/25mm dia. 67 S&F for male brass threaded Adaptor (MTA/ MBTA) ) 68 S&F for female brass threaded adaptor (FTA/ FBTA 69 S&F for solid PVC door frame of size 50 mm x 47mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specified. 70 S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed togeather with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified. 71 S&F for 100mm long mild steel butt hinges, cold rolled MS, medium type,and fixed complete all as specified. 72 S&F for alumimnium handles of size100 mm, cast type anodised complete all as specified. 73 S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed. 74 S&F for anodised aluminium powder coating (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified all as specified. 75 S&F for anodised aluminium powder coating (minimum thickness of powder coating 50 micron)window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified 76 S&F for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. 77 S&F for5.50 mm thick sheet glass(tinted/reflective type) in squareeach pane complete 78 S&F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples 79 M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces including finishing surfacefair and even without using extra cement and water proofing compound complete all as specified. (Note: WPC shall be paid and measured saperately) 80 Spreading and levelling in layers not exc 25 cm thick ,well ramming including watering as required. all as specified. 81 M&L for cutting into existing manhole for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified. 82 M&L for cement concrete (1:2:4) type B-2 using 40 mm stone graded aggregate in foundations, filling and mass-concrete all as specified. 83 Excavating in post holes (or similar holes) each n exc 0.5 Cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil complete 84 M&L for100 mm thick cement concrete 1:2:4, type B-2 (using 40 mm grade stone aggregate) as in floor finishing top surface even and smooth without using extra cement all as specified. 85 M&L for forming contraction (Dummy) joints 65 mm deep x 10mm wide filled with sealing compound grade A complete all as specified. 86 M&L for 50 mm thick cement concrete in 1:2:4 mix, type B-1 (using 20 mm graded stone aggregate) as in duct including finishing surface even and smooth without using extra cement all as specified. 87 M&L for brick work with sub-class `B bricks, straight or curved on plan exc6.0 mtr mean radius and built in cement mortar 1:4 all as specified. 88 M&L for cutting of existing concrete floor by diamond cutter and breaking by mechanical tool of any size without disturbing existing adjacent structure and removal of the same to a distance not exc 5 0mtr and depositing where directed at a level n exc. 1.5mtrabove the starting point complete all as specified and as directed. 89 M&L for preparation of newly plastered surface of wall and applying three coats ofwhite wash compele all as specified. 90 E/M PORTION S&F for flame proof wiring with single core PVC insulated and unsheathed 1100 Volts grade (ZHFR) Zero Halogen Flame Retardant Smoke Free Non-Toxic Non-Corrosive Electric Cable with multi stranded copper conductor of size1.5 Sq.mm phase and neutral drawn in and including ERW rigid steel stove enamled black conduit heavy duty ISI marked of size 20mm dia in concealed surface type including all flame proof conduit fittings and accessories such as tees, junction boxes, bends, duly tested by CMRI Dhanbad duly earthed with single core PVC insulated and unsheathed 1100 Volts grade (ZHFR) Zero Halogen Flame Retardant Smoke Free Non-Toxic Non-Corrosive Electric Cable with multi stranded copper conductor of size1.5 Sq.mm in greencolour as continuous earthing wire connected to earth dolly complete all as specified and directed by Engineer-in-Charge for one light point controlled by one way switch.. 91 All as per item No. 90.00 above but for One fan point controlled by one way switch complete all as specified. 92 S&F for flame proof wiring with single core PVC insulated and unsheathed 1100 Volts grade (ZHFR) Zero Halogen Flame Retardant Smoke Free Non-Toxic Non-Corrosive Electric Cable with multi stranded copper conductor of size2.5 Sq.mm phase and neutral drawn in and including ERW rigid steel stove enamled black conduit heavy duty ISI marked of size 20mm diain concealed surface typeincluding all flame proof conduit fittings and accessories such as tees, junction boxes, bends, duly tested by CMRI Dhanbad duly earthed with with single core PVC insulated and unsheathed 1100 Volts grade (ZHFR) Zero Halogen Flame Retardant Smoke Free Non-Toxic Non-Corrosive Electric Cable with multi stranded copper conductor of size2.5 Sq.mm in greencolour as continuous earthing wire connected to earth dolly complete all as specified and directed by Engineer-in-Charge .[Note for Item No. 90.00, 91.00 & 92.00 :- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.] 93 S&F for flameproof, weather proof direct entry type rotary switch with cable terminal box in cast aluminium alloy LM-6 enclosure epoxy powder coated single pole 230 volts 16 Amp ON / OFF switch AC certified by CRMI for group II-A & II-B including compression glandsall as specified and directed. 94 S& F for Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16 Amp, 250V, 2P + earth complete all as specified and directed. 95 M&L for cutting walls of any type, making holes for fixing of exhaust fan any size or sweep and making good surface with cement plasteringin CM 1:4 , finishing and colouring with existing colour matching complete all as specified and directed. 96 S&F for flame proof exhaust fan 12 inch,0.25HP, AC, single phase, 230 volts, 1440 RPM complete with in-built louvers shutters and including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of size 0.75 sqmm completeall as specified and directed. 97 S&F for flame proof wall mounted fan12 0.25HP, AC single phase, 230 volts, 1440 RPM complete with in-built louvers shutters and including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of size 0.75 sqmm completeall as specified and directed. 98 S&F for flameproof weather proof for installation in hazardous area as per IS-2148/ 81/ LED Tube light fitting epoxy powder coated with provision of cable glands duly tested and certified by CMRI Dhanbad suitable for and including 16/20 WattLED Tube made out of cast iron aluminium alloy LM-6 enclosure with clear heat resistant borosilicate glass tubing spring loaded non sparking bipin lamp holder built in control gear fitted with copper wound ballast condenser starter all accessories prewired including 02 Nos M-20 cable entries mounted on wall/ column steel structure complete all as specified and directed. 99 S&F forflame proof weather proof for installation in hazardous area as per IS-2148/ 81/ LED Bulk head light fitting epoxy powder coated with provision of cable glands duly tested and certified by CMRI Dhanbad suitable for and including 30 WattLED Tube made out of cast iron aluminium alloy LM-6 enclosure with clear heat resistant borosilicate glass tubing spring loaded non sparking bipin lamp holder built in control gear fitted with copper wound ballast condenser starter all accessories prewired including 02 Nos M-20 cable entries mounted on wall/ column steel structure complete all as specified and directed. 100 S&Ffor flame proof control Panel/WP lighting distribution panel (SPN 4 Way) main Incomer16/25 amp two Pole MCB-1 Nos Out going 6 Amp/10 amp 1 P MCB-2 Nos completeall as specified and directed. 101 Supply, laying and testing Lt cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sq mm 2 core complete all as specified. 102 M&L for dry sand cushioning for protection of under ground cables (8cm before laying the cable and 15cm after laying the cable in trenches) complete all as specified. 103 M&L for well burnt Sub class B, bricks using old size, laid dry, flat over the cable abutting each other, length of brick equal to width of brick complete all as specified and directed. 104 S&F for40mm bore light grade ISI marked GI tubing laid in trenches or inserting in horizontal boring for cable protection including fixing with MS Clamp and nut bolts complete all as specified & as directed. 105 M&L for making horizontal hole by mechanical boring under hard standing, pavements or roads for insertion of GI pipes 40 to 80 mm bore and making good the disturbed surface complete all as specified and as directed.(Note: GI pipe shall be measured and paid separately) 106 M&L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to earth lead wire of GI wire 4mm dia by means of nuts/bolts and washers, check nuts of galvanized iron or steel including 15 mm dia GI pipe light grade upto 1.5 mtr below GL for protection pipe, excavation and earth work charcoal dust, common salt, PCC 1:3:6type C-1 chamber with cover and RCC1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm c/c both way with MS handle 12mm dia PGI funnel and wire mesh all as shown in electrical plate No 5 of SSR Part-I connected to ear thing test point all as specified or indicated including testing on completion all as directed by Engr-in-Charge. 107 M&L for point wiring using approved colour coding as per IS with 1100 volt grade 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade (IS:694) drawn into and including PVC conealed conduit heavy duty including all accessories after chasing/ concealed in wall/ roof / ceiling including pressed steel concealed terminal boxes 1.2 mm thick 60 mm deep of required size with modular white cover plate with frame for housing switches/ sockets/ regulators etc. duly earthed with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as continuous earthing wire complete all as specified for one light point controlled by one switch one way complete all as specified.[Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.] 108 Allas per item No. 107.00 abve but for one Fan point controlled by two way switch complete all as specified. 109 M&L forsubmain wiring with two single core 1100 volt grade FRLSH PVC insulatedflexible copper conductor cable of size 2.5 Sqmm and one single core PVC insulated FRLSH flexible copper conductor cable green colour of size 2.5 Sqmm as earth lead includingconcealed PVC conduit medium grade, ISI mark of dia not less than 25mm including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with adjoining surfaces all as specified.[Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.] 110 S&F for recess mounted LED light fitting 2 feet x 2 feet 36 watt, smart glow, general purpose square shaped luminaire with low height CRCA housing and high transitivity diffuser suitable for office application with diffused acrylic cover complete with all accessories and connecting up with three core flexible copper cable of size 23/0.0076 complete all as specified and as directed. 111 S&F for wall/surface mounted type LED light fitting batten type complete with LED 1x 20Watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 coretwisted flexible copper conductor cable complete all as specified and as directed. Make : Philips Cat Part No BN 021C LED 20S PSU CW GR S2 / Havells Cat Part No : ENDURA LINEAR NEO BS 20W LED 865 SPC WH or equivalent make of Wipro. 112 S&F in replacement of wall / surface mounted type LED light fitting batten type complete with LED lamp 10 Watt(2 feet long), poly carbonate body and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with twine coretwisted flexible copper conductor cable complete all as specified and as directed. Make : Philips Cat Part No BN 021 LED12S 6500 PSU GR / Havells Cat Part No : ENDURA LINEAR NEO BS 10W 865 SPC WH or equivalent make of Wipro. 113 S&F for Air ventilating fan 300 mm sweep PVC body, AC, single phase, 230 volts, 1200 RPM complete and making holes with lovoured shutters including mounting frame and connecting the fan to ceiling rose including provision of three core flexible copper conductor cable of size 1.5 sqmm copper including to inside out surface & white wash etc with not less than 0.5mtr long to connection all as specified and directed. 114 S&F for modular switch one way 6 Amp , one module ISI marked complete all as specified. 115 S&F forceiling rose 65 x 50mm three terminals complete all as specified . 116 S&F for flush mounting factory made Ekinoxe SPN DBs Double door, IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar andcables ties for cable management fully insulated bus bar 4 way with 100 Amps rated bus bar complete all as specified and directed. 117 S&F for MCB SPN (single pole and neutral), 240 volts,32 Amps breaking capacity 10 KA, ‘C’ Series. etc, complete all as specified and directed. 118 S&F for MCB SP (single pole) 240 volts, 6 to 32 Amps, 50HZ, 10 KA, ‘C’ series complete all as specified and directed. 119 S&F for25 mm bore galvanised steel tube, medium grade including all fittings in trenches complete all as specified. 120 S&F for22 mm bore galvanised steel tube, medium grade including all fittings in trenches complete all as specified. 121 Supply and fixing for Gun metal globe or gate valve ISI marked with iron wheel head, screwed both ends for iron pipe of bore of 25 mm complete all as specified. 122 Supply and fixing for Gun metal globe or gate valve ISI marked with iron wheel head, screwed both ends for iron pipe of bore of 20 mm complete all as specified. 123 M&L for valve chamber of size 450mmx450mmx450mm (Internal) with fly ash brick masonary 230 mm thick in CM 1:6, PCC 1:4:8 type, D2 foundation 75 mm thick, finished fair and even, PCC 1:2:4 type, B1 coping 150 mm thick on top of brick wall for fixing chamber cover, 10 mm thick cement mortar 1:4 plaster on exposed surfaces of brick wall (both internal and external), mild steel cover of 3.00 mm thick inclduding mild steel angle iron 40x40x6 mm size frame fixed to PCC coping with the same size of angle iron hold fast and with necessary handle and locking arrangements, metal surfaces duly painted with black bituminous paint over a coat of red oxide zinc chrome primer and finishing the masonry/concrete surfaces with 3 coats of white wash including necessary excavation and earth work complete all as specified and directed. 124 Supply, laying and testing Lt cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4core complete all as specified. 125 S&F for LED flood light 120 watt 230 volt AC outdoor type with energy saving environment friendly long life exclusive innovative die cast aluminium IP66 flood light fiitingsuitable for high lighting archetectural facade and general purpose lighting with brackets and other reqd items all as specified and directed by Engr-in-Charge. 126 S&F for sheet metal enclosures DB 04 way for use of Single MCB and Isolators 200 Amp busbar all as specified. 127 S&F for sheet metal enclosures for distributio board SPN04 way double door for for use of 200 Amp ratedbus bar and neutral,earthing bar and din rail complete all as specified. 128 S&F for MCB SPN (single pole and neutral), 240 volts,40 Amps breaking capacity 10 KA, ‘C’ Series. etc, complete all as specified and directed.
