Tender For Comprehensive Repairs Of E/M Installation Under Age B/R Dett-A Of Ge 862 Ews; 1 Demolition ofcement concrete in ground floor and pavings n.exc 15cm thick below or above ground level including tiles and similar works, complete all as specified and directed. 2 Demolition ofreinforced cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level including tiles and similar works, complete all as specified and directed. 3 Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing outside MD land, complete all as specified and directed. 4 Demolition of Brickwork or stone/ boulders masonry built in cement or cement lime mortar incl all quions, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed. 5 Taking down of cement plaster on brick/stone or conc surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed. 6 Dismantling of asbestos cement corrugated/ plain sheets in roof covering including ridges, complete all as specified and directed. 7 Taking down of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed. 8 Dismantling of ceiling board(Fibre,pulp,,insulation etc) or insulation boardwith frame / slabs/any thickness including cover fillets, complete all as specified and directed. 9 Dismantling of wrought iron or mild steel works of any description and in any position, complete all as specified and directed. 10 Dismantling of timber scantlings40 sq. cm and over in section, in any position ( framed work) , complete all as specified and as directed. 11 Dismantling of floor, hearth or wall tiling, skirting including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 12 Taking down of chowkhats or frameswith shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified and as directed.Note : The rate inlcudes making good of surfaces w/o any extra cost to govt. 13 All as per item No12 here-in-before but exc 1.5 Sqmbut n.exc 4 sqm each. 14 Taking down shutters of any description exc 1 sqm but n exc 2 sqm each, complete all as specified and directed. 15 Taking down shutters of any description exc2 sqmbut n exc 4 sqm, complete all as specified and directed. 16 Hackingoutoldbrokenglass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. 17 Dismantling water tank exc 500 ltrs and n.exc 1000 ltrs capaicty and removing to store, complete all as specified and directed. 18 Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, complete all as specified and directed. 19 Dismantling fencing wire mesh/barbed wire any type in any position, complete all as specified and directed.Note:Mode of measurement is only in X and Y axis for any type of fencing wether mesh/Barbed wire/Concertina coil. 20 Formwork to sides of concrete foundations, footing, base of columns, plinth beams, flat surfaces, complete all as specified. 21 Formwork to Flat/Curved faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for rough finished surfaces of concrete, complete all as specified.Note: Involves head load with steep slope upto 100 Rm. 22 Formwork to side & soffits of suspended slabs such as roof slabs, floor slabs, landing and simillar works; not exceeding 200mm thick (Horizonal or Sloping) Flat/Curved surfaces of concrete, complete all as specified.Note: Involves head load with steep slope upto 100 Rm. 23 M&L for reinforced cement concrete M-30 (design mix) (using 20mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams, bases for columns, etc(for water retaining structure), complete all as specified and as directed.Note: Involves head load with steep slope upto 100 Rm. 24 M&L for reinforced cement concrete M-30 (design mix) (using 20mm graded crushed stone aggregates) as in Walls, retaining walls, basement walls, ballast walls and the like (for water retaining structure), complete all as specified and as directed.Note: Involves head load with steep slope upto 100 Rm. 25 M&L for reinforced cement concrete M-30 (design mix) (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors the like (for water retaining structure), complete all as specified and as directed.Note : Involves head load with steep slope upto 100 Rm. 26 M&L for TMT steel bars 10mm dia and over as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.Note: Involves head load with steep slope upto 100 Rm. 27 M&L for TMT steel bars 6mm to 8mmdia and over as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.Note: Involves head load with steep slope upto 100 Rm. 28 M&L for Brick work with sub class B bricks straight or curved on plan exceeding 6 Metre mean radius in cement mortar 1:4, complete all as specified and as directed. 29 All as per Item No 28.00 here-in-before but exceptbricks. 30 M&L for random rubble stone masonary well bonded, bedded and solidly hearted in cement mortar 1:6, complete all as specified and as directed. 31 All as per Item No 30.00 here-in-before but except stone. 32 M&L for 15mm thick rendering on fair faces of brick surfaces finished even and smooth W/O using extra cement in CM 1:4 complete all as specified and as directed. 33 M&L for 15mm thick rendering on brick or concrete surfaces in CM 1:6 finished even andsmoothw/o using extra cement, complete all as specified and as directed. 34 M&L for rendering 20mm thick in cement mortar (1:4)on stone masonry surface, finished even and smooth without using extra cement complete all as specifed and directed. 35 M&L for rendering 20 mm thick in cement mortar 1:6 on stone masonry surface, finished even and smooth without using extra cement, complete all as specified and directed. 36 S&F Pre-painted coloured galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws//L or J hooks, complete all as specified and as directed. 37 S&F Pre-painted coloured galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. 38 S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe 410W (Gde E-250) quality-A steel, complete all as specified and as directed. 39 S&F(plain orchequered ) channels ,square cutor notched ( oridinary and counter sunk) forming holes, w/o any attatchment of Fe 410W (Gde E-250) quality-A steel, complete all as specified and as directed. 40 Erection and fixing only steel work in roof trusses including special shape washers et. Complete using using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240, complete all as specified and directed. 41 S&F Mild steel bolts.exc. 5 cm lengthnot exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 11 to 15 mm neck dia, complete all as specified and as directed. 42 Supply and fixing of 4mm thick designer ceiling board (Make Everest Hill & Lake Pattern) in ceiling fixed with screw as per manufacturers instructions , laid on hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white.The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet & of size 24 x 32 x 300 mm spaced at 12 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres.Hangers of GI wire 4 mm dia to be fixed by approved rowl plug, level adjusters andscrews etc.The last hanger at the end of each main runner shall not be grater than 450 mm from adjustacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to from 1200 x 600 mm modulescross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturction complete all as specified and as directed. 43 M&L for 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) in sub base offloor, complete all as specified and as directed. 44 M/L for colouredNon skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe colour of tiles over and including screed bed 15 mm thick in CM 1:4, complete all as specified and as directed. 45 M&L for coloured glazed ceramic tiles in vertical surface( 600x 300x7mm thick ) set and jointed in neat cement slrry and pointed in white or coloured cement to matchthe colour of tiles over & including 15mm thick rendering in CM (1:4), complete all as specified and as directed. 46 M&L for Vitrified tiles colored600x600mm and10mm thick as in floors jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces over and including screed bed 15 mm thick in CM 1:4, complete all as specified and directed.Note:The contractor shall have no claim on difference what so ever on shade /colour of tile. 47 All as per Item No 46.00 here-in-before but on vertical surfaces over and including 15mm thick rendering in CM (1:4). 48 M&L for 18-20mm thick Machine cut kota stone slab flooringover and including 20 mm thickscreed base Cement mortar1:3laid and jointed with grey cement slurry mixed with pigment to match the shade of the slabincluding rubbing and polishing, complete all as specified and directed. 49 M&L for 18-20mm thick Machine cut kota stone slab in riser of steps, Skirting, dado and pillar laid over and including 15mm thick rendering in CM (1:3) with neat cement Slurry, complete all as specified and directed. 50 M&L for Cutting/ grinding / polishing to existing kota stone flooring including minor repairs and polishing, complete all as specified and directed. 51 S&F in repair steel rolling shutter 1.25 mm thick withball bearing, as specified including top cover, anchoring rod , hasp and stapple , guiding rail and one shop coat of primer, erected in position as indicated complete push pull or manual type, complete all as specified and directed. 52 Taking down rolling shutter and refixing in the same opening of exc 2 sqm each and including necessary repairs like safety lever lock, ball bearing, anchoring rod and etc, complete all as specified and directed. 53 S&F 1.25 mm thick pressed steel frame 125x60mm for doors with one or more rebates incl necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed. 54 S&F 1.25 mm thick pressed steel frame105x60mm for doors with one or more rebates incl necessary fixing lugs. Hinges lock strike plate etc, complete all as specified and directed. 55 S&F SolidPVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed. 56 S&F 35mm thick Factorymade second class hard wood plain framed pannelled shutter (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned, complete all as specified and directed. 57 S&F 2nd class hardwood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass guage, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass,etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a); supplied and fitted to chowkhats complete all as specified and as directed. 58 S&F factory made solid panel PVC door shutter withMS square tube30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colourPVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification, complete all as specified and directed. 59 S&F Factory made MS tubular Box type windowof MS rolled steelsection conforming to IS-1038 and shall be ISI marked manufactured by ISI approved manufacturer, openable frames shall be fabricated of sections as approved by Engr-in-Charge, corner welded to form a solid fused welded joint handles shall be of z section welded with openable frame box steel section(Consisting of both shutter glazed shutter and gauge shutter complete) used in outer frame shutter frame and central frame shall be ERW secton of 16 gauge with fixing lugs to be fixed as per provision of IS-1038except that top lugs shall not be provided , all shutters of windows shall be provided with 4 Nosfriction free hinges, 2 Nos 75 mm tower bolts to each leaf of window one at top and one at bottom welded on 3 mm thick steel sheet piece of suitable size which shall be in turn welded to z section of steel window to provide suitable arrangement of using tower bolt and 1 nos bow handle in each shutter. Glazed shutter and , gauged shutter of window , mild steel casement stays 300 mm with hinged joint and two plates with studs complete all as specifiedwith all fittings and fixtures with glazing bars, 3mm sheet glass in glazedshutter and , GI wire mesh,of 0.56 nominal dia and average width of aperature 1.18 mm in gauged shutter, etc cpmplete all as specified and as directed. 60 S&F of MS guard bars/grills as specified in between glazed and fly proof window shutter(sand witching guard bars/grill) as per drg No CEPZ/TD-325/07 dt 04.12.07 primer coated, complete all as specified and directed. 61 M&L Galvanised stain less steelwire cloth 0.56 mm nominal dia of wire and averqagae width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples, complete all as specified and directed. 62 S&F Butt hinges, medium weight, stain less steel 100 mm size, complete all as specified and directed. 63 S & F Aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long ISI Marked, complete all as specified and directed. 64 S&F mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12 mm dia with and incl. a minimumof 6 bolts and nuts four on bolt plate and two on staple plate of 300 mm long complete all as specified and as directed. 65 S&F Extruded aluminium alloy handles, fabricated type., anodised 150mm ISI Marked, complete all as specified and directed. 66 S&F 3 mm Sheeet glas ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed. 67 S & F in repair Stainless steel Curtain Rod 25mm dia mild steel chromium plated fancy type with fixing brackets, steel balls , dooms, and knobs at both ends as per requirement, complete all as specified and directed. 68 M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection finished even and fair without using extra cement and providing jointsthroughout the thickness of the plinth protection, complete all as specified and directed. 69 M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in drain,coping to path ,edging,benching and the like incl formwork, complete all as specified and directed. 70 M & L cement concrete type C2 1:3:6 (using 40 mm graded crushed stoneaggregate) as in surface channel or drains,complete all as specified and directed. 71 Extra for formiing fair finished drain or channel 30Cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed. 72 M&L for mild steel Framed work such as steel gates, chowkhats and other similar works of angle or other section with gusset plates rails, braces etc, complete, drilled for fixing of steel sheeting or other covering etc.conforming to Fe – 290 Gde E-165 complete including taking down existing gate, complete all as specified and directed. 73 S&F in repair vitreous china wash down water closet pan pan (pedestal pattern), white excluding flushing cistern, flush pipe, complete all as specified and directed. 74 S&F in repair plastic water closet seat cover, black / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC. complete all as specified and as directed. 75 S&FPVC flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete as in repairs, complete all as specified and directed. 76 S&F in repairs bib tap cast copper alloy chromium plated fancy type 15mm bore withcrutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 77 S&F Stop valve cast copper alloy(concealed type) with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair, complete all as specified and directed. 78 S&F angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed. 79 S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 80 S&F in repair tubular towel rail 20mm dia, D type, chromium plated 60cm long between flanges, complete all as specified and directed. 81 S&F in repair chromium plated shower roses with or without swivel joints of 125mm size, including fixing to steel pipe or union, complete all as specified and directed. 82 M&L in repair75mm diaoutlet of inPVC SWR foor trap plain with grating including jointing with solvent cement including removing old trap and make good existing floors etc, complete all as specified and directed. 83 S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed. 84 S&F in repair SS Gratings of 100 mm dia, fixed in repairs, complete all as specified and directed. 85 S&F steel water tubes medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors 15 mm bore in repair, complete all as specified and directed. 86 S&F steel water tubes medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors 20 mm bore in repair, complete all as specified and directed. 87 S&F rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, complete all as specified and directed. 88 S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixedfixed in repair.of 20mm, complete all as specified and directed. 89 M&Lfor 75 mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) in sub base offloor, complete all as specified and directed. 90 M&L for sand filling under floors, cushning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and directed. 91 M&L for coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade including taking out of old precast concrete interlocking paver block, complete all as specified and directed. 92 M&L for prepolished coloured chequered cement concrete tiles size 30cmX30cmX25mm thick, set, jointed and pointed in neat cementslurry in floor with grey pigment cement and pigments over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specifiedand directed. 93 Excavation in post holes or similar holes each nexc 0.5 cum getting out in any type of soil, complete all as specified and directed. 94 S&F angle iron section as in horns, posts, struts including notching drilling holes for wire mesh etc; conforming to Fe-290, complete all as specified and directed. 95 M&L for cement concrete 1:3:6 type C 2 (using 40 mm graded stone aggregate ) as in foundations fillling and mass concerete, complete all as specified and directed. 96 S&F MS flat iron of size 40x6mm to secure chain link fencing, complete all as specified and directed. 97 M&L mild steel round bars 10 mm dia or over, cut to length, bend to shape required, fixed independently to support chain link fencing complete all as specified. Fe 410-0 or Fe 310-0, complete all as specified and directed. 98 M&L for mild steel bolts purpose made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut. Diaexc 5 to 10 mm dia and nexc 5 cm long, complete all as specified and directed. 99 Supply only Chain link MS Galvanized fencing, any size or type, complete all as specified and directed. 100 Fixing only Chain link Fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, complete all as specified and directed. 101 S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm to 80mm spacing and straining and ixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc, complete all as specified and directed. 102 Surface excavation n exc. 30cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed. 103 Rolling and consolidating old surfaces in cutting with power rollers of capacity 8 to 12 tonne complete all as specified and directed. 104 M&L for polythene film 150 micron thick laid over and including a coat of bitumen primer @ 0.30 to 0.50 kg/sqm, complete all as specified and directed. 105 M&L for cement concrete work in pavement/hardstanding of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less, complete all as specified and as directed. 106 Forming 12mm thick Expansion joints filled with pre-formed bituminious filler and top 30mm primed and sealed with sealing compound Grade ‘A’, thickness of concrete slab 250mm including providing 20 mm dia mild steel dowel bars 50cm long (25cm in each slab) with ferrules, spaced at 300 mm centres, including boring form work and preformed filler for dowels, complete all as specified & directed. 107 Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade ‘A’, complete all as specified & directed. 108 M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new or previously untreated wood and wood based surface incl preparation completecomplete all as specified and directed. 109 M&L for applying one coat of synthetic enamel paint overon oldwood and wood based surface incl preparation completecomplete all as specified and directed. 110 M&L preparation of new of previously untreated steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed. 111 M&L preparation ofold painted steel or iron surfaces of any description over 10 cm width or girth not otherwise described and applying onecoat of Synthetic enamel paintcomplete all as specified and directed. 112 Preparing newly plastered surface of walls and apply two coats of oil bound distemper, complete all as specified and directed.Note-Painting shall be done by Painting roller. 113 Complete reomoval of existing treatment over walls, by using mechanical equipment (Electric sander ) and preparation of surface to receive the treatment and applying two coats of distemper oil emulsion, complete all as specified and directed. Note : Once the surface is cleared off old treatment completely, the stage for treatment shall be approved by GE. 114 M&L for preparation ofnew plastered and unplasteredsurfaces of walls andapplying two coats of Cement Base Paint onwalls over a coat of alkaili resistant priming paint in any position, complete all as specified and directed. 115 M&L for preparation of old decoratedplastered/unplasteredsurfaces of wall by brooming down or steel wire burshing scrapping down smoke soot moulds and efflorescent salts and treating oil and greasy spots andapplying a coat of cement base paint, complete all as specified and directed. 116 M&L for applying three coats of white wash on newly plastered surfaces of wall incl prepration, complete all as specified and directed. 117 M&L preparation of old decorated surface of walls and applying one coat of white wash on walls, complete all as specified and directed. 118 M&L for one coat of weather proof exterior emulsion paint on old decorated surfaces of walls after preparation of surfaces, complete all as specified and directed.
