Conservation And Beautification Of Waghapur Lake Tal. Bhudargad Dist. Kolhapur- 1 Sub-work No. 1 -Desilting, Deweeding and Dewatering Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material up to a distance of 50 metres beyond the building area and stacking as directed ,including dewatering, preparing the bed for the foundation and necessary back filling with a vailable earth / murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5m) By Mechanical Means 2 Excavation for foundation in Hard-rock by controlled blasting including trimming and leveling the bed by chiselling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres. from the building area including dewatering and backfilling with available earth soil / murum watering, ramming etc. complete. (Lift upto 1.5m) By Mechanical Means 3 Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary forfoundation and other parts of the the works and pumping out water during and after excavation as may be required by using 10.0 to 19.0 BHP pump etc. complete. ( prior approval of Super intending Engineer will be necessary) 4 Desilting the Lake in wet or dry condition excluding Conveying materials obtained from Lake beyond the work site, stacking, spreading,etc. complete 5 Conveying materials obtained from Lake including all lifts, laying in layers of 20 cm. to 30 cm. breaking clods, dressing to the required lines, curves,grade sand section, watering and compacting to not less than 97% of standard proctor density for a lead of 300m. to 500 m. inclusive, from the site of excavation to the site of deposition as directed.20 % to Farm 6 80 % to Dump Yard 7 Labour charges for removing grass, thorney shrubs, Jungli shrub, Kubabul and a like grass along roadside making the ground clean by showel and phavaras etc. complete. 8 Sub Work No. 2 - Gabion Wall Providing and Constructing gabion structure 1Meter high or required section madeup of soft mechanically woven hexagonal shaped G.I. wire confirming to IS 16014:2012 having zinc plus PVC coating of overall diameter of 3.7 mm and tying lacing wire of 3.2 mm with edge wire confirming to overall diameter 4.4 mm edges being mechanically selvedged including placing inposition, fitting neatly with trap stone rubble (15 to 23 cm ) all loose ends to be securely tied (Excluding transportation) etc. complete. (In Dry condition and for under water installation extra cost to be considered) 9 Filling in plinth and floors with approved excavated material in 15 cm. to 20 cm. Layers including watering and compacting etc. complete. 10 Sub Work No. 3 - Earthen Bank Protection WorkExcavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means 11 Excavation for foundation in hard murum and Boulders including removing the excavated material up to distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc.complete. (Lift upto 1.50 m) By Mechanical Means 12 Providing and laying Cast in situ / Ready Mix cement concrete in M-10 of trap / ganite / quartzite / gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying / pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 13 Providing andl aying Cast in situ / Ready Mix cement concrete M-25 of trap / granite / quartzite / gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying / pumping, compaction and curing roughening the surface if special finish is tobe provided ( Excluding reinforcement and structural steel ) etc. complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 14 Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, coverblocks, laying / pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer /concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 15 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pilecaps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars,bindingwith wires or tack welding and supporting as required complete. 16 Filling in plinth and floors with approved excavated material in 15 cm. to 20cm. Layers including watering and compacting etc. complete. 17 Providing expansion joints with 25 mm thick bituminous pad as per detailed drawings etc. complete. 18 Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete. 19 Sub Work No. 4 - Ghat Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means 20 Excavation for foundation in hard murum including removing the excavated material up to distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc.complete. (Lift upto 1.50 m) By Mechanical Means 21 Providing soling using 80 mm size trap metal in 15cm. Layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. 22 Providing and laying in situ / ready mix cement concrete of M-10 proportion with trap / granite / quartzite / gneiss metal in foundation including necessary formwork, compacting and curing etc. complete. (with reversible drum type mixer with SCADA with fine agreegates of required specifications (Natural sand / VSI sand finely washed etc ) 23 Providing and laying insitu / ready mix M-20 cement concrete of trap / granite / quartzite / gneiss metal for approach slab / Rigid pavement including compacting ,finishing, curingetc. complete. (excluding reinforcement ) (with reversible drum type mixer /concrete batch mix plant (pan mixer) with SCADA with fine agreegates of required specifications (Natural sand / VSI sand finely washed etc ), cement 6.40 bags/cumt) 24 Providing selected hard murum filling including laying in layers of 15 to 20 cm with watering and compacting etc. complete. 25 Providing andl aying Cast in situ / Ready Mix cement concrete M-25 of trap / granite / quartzite / gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying / pumping, compaction and curing roughening the surface if special finish is tobe provided ( Excluding reinforcement and structural steel ) etc. complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 26 Providing and laying Cast in situ / Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, coverblocks, laying / pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer /concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 27 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pilecaps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars,bindingwith wires or tack welding and supporting as required complete. 28 Sub Work No. 5 - Stone Pitching Excavation for foundation in hard murum and Boulders including removing the excavated material up to distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc.complete. (Lift upto 1.50 m) By Mechanical Means 29 Providing selected hard murum filling including laying in layers of 15 to 20 cm with watering and compacting etc. complete. 30 Providing dry rubble stone pitching 23 cm (about 9 inch) thick including all material, quarry spalls, labour etc. complete. 31 Sub Work No. 6 - PathwayExcavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means 32 Providing dry / trap / granite / quart zite / gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. 33 Providing and laying Cast in situ / Ready Mix cement concrete in M-10 of trap / granite / quartzite / gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying / pumping, compacting, roughening the mif special finishis to be provided, finishing if required and curing complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 34 Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram / Sq. cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete 35 Providing and laying Cast in situ / Ready Mix cement concrete in M15 of trap /granite / quartzite / gneiss metal for bed blocks, foundation blocks and such other items in cluding bailing out water, Steel centering, formwork, laying / pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honey combed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honey combed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed. ), with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 36 Providing and fixing Guard Railing of 1000 mm height as per Type D Drg. No. 15 dt . 20 - 4 -79 , and fixed in 40 x 40 x 6 mm iron, angle embedded in 1:2:4 cement concrete bedding patti as per detailed drawing, with 3 coats of approved of yellow and black paint. 37 Sub Work No. 7 - Public Toilet BlockExcavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A- 1/259) 38 Excavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd�A-3/259) 39 Providing dry trap/ granite/ quartzite/ gneiss, rubble stone soling in 15 cm to 20 cm thick layers including hand packing and compacting, etc. complete. (Bd-A-12/264) 40 Providing and laying in situ Cement Concrete M-10 of trap/ granite / quartzite / gneiss metal for foundation and bedding including bailing out water, form work, compaction, curing, etc. complete. (Cement 5.90 bags / cum) PCC M - 10 41 Providing uncoursed rubble stone masonry of trap/ granite/ quartzite/ gneiss metal in CM 1:5 for foundation of piers, abutments, wings etc. including bailing out of water, striking joints, scaffolding and watering etc. complete. 42 Filling in plinth & floors with approved excavated materials in 15 cm layers including watering &compacting complete 43 Providing and casting in situ C.C. of trap / granite/ quartzite / gneiss metal of approved quality for RCC works as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, form work, compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) R.C.C. LINTEL-150 44 Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. 45 Providing and casting in situ C.C. of trap / granite/ quartzite / gneiss metal of approved quality for RCC works as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, form work, compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) Slab M200 46 Providing and fixing in position steel bar reinforcement of various diameters for RCC piles, caps, footings, foundations, slabs, beams, columns, canopies, staircases, newels, chajjas, lintels, pardies, copings, fins, arches, etc. as per detailed designs, drawings and schedules; including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required, etc. complete(including cost of binding wire). (Bd-F- 17/306)TOR Steel 47 Providing and fixing M40 grade tick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S.65241983 having 6mm dia.bars3 Nos. And stirrups @ 250 mmc/cand fixing in wall with 6 Nos of hold fast of 12mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm . 48 Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron holdfast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete. 49 Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 50mm thick with 3mm diameter mild steel bar reinforcement,of approved design on both side, fixing in cement mortar 1:3 and curing etc. complet 50 Providing internal cement plaster 12 mm thick in a single coat in C.M.1:3 without neru finish to masonry , concrete surface in all positions including scaffolding and curing complete. 51 Providing and laying matt finish ceramic tiles of having size 30 cmx 30 cm confirming to I.S.15622/2006 (group D II-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. complete. 52 Providing and laying cement concrete flooring 40mm thick with M15 cement concrete laid to proper level and slope in alternate bays including compaction filling joints, marking lines to give the appearance of tiles of 30cmx30cm or other size laid diagonally/square etc finishing smooth (with extra cement )in any colour as directed and curing etc.complete.with Crushed sand VSI Grade 53 Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to correspondng I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. 54 Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black back lite seat with all necessary pipe connection etc. complete. 55 Providing and fixing white glazed earthenware Wash Hand Basin of 45cm. x 30cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. 56 Providing soak pit of size 120cm x 120cm x 120cm including excavating and filling with brick-bats. 57 Providing and fixing on walls/ceiling/ floor 15mm dia. CPVC pipe with necessary fittings, remaking good the demolished portionetc.complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 58 Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and withnecessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc.complete. 59 Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/ waste pipe and with necessary fxtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. As directed by Engineer 60 Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters 61 Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. 62 Providing and fixing Bib cock stop tap of brass heavy of 15 mm dia. At site of work 63 Providing and fixing partition with kadappa stone of all size sand 25 mm thick polished on both side and edge stoorig in a lncluding fixing in position in cement mortor 1:4 curing polish-ing, cleaning etc complete. 64 Name plate with wording as directed on plastered srface in oil painting 65 Providing and fixing orissa type colour glazed earthen ware 625x450 mm. w.c. pan including trap, C.I. soil and vent pipe upto the outside face of wall including 100mm. dia. C.I. plug, bend, 15mm. thick 10 litre PVC flushing cistern with all necessary pipe connection etc. complete. 66 Sub Work No. 8 - Compound Chainlink FencingProviding and erecting 1.2 meter high wire fencing with five rows of barbed wire supported on mild steel angle ( 50 x 50 x 6mm ) postat 2.5 m c/c including excavation of pits of foundation concrete fixing the posts in (1:4:8) cement concrete block of 45x45x45 cm and fastening the Wires and painting the angles with one coat with red lead primer and two coats of oil painting etc.complete 67 Sub Work No. 9 - Beautification Work(Environmental Awareness, Benches, Solar Street Light, Dustbin, Sign Board, Open gym, Children Play Equipment) Providing and fixing VIP Bench CI Frame height 5.48 mêter and weight 30 kilogram Decorative Leg, Seat plates FRi Patrujan hot press size metre x 1.20 metre long, wood finish, both side PP Cap for fixing 12.5 milimeter Stainless steel Nut bolt toatal 9 seat plates etc complete. 68 Providing and Fixing Solar Street light. Power Output > 75 Wp at 16.4 +- 0.2 Volts at STC,Battery Capacit > 12.8V (nominal), 30 Ah at STC (1 Day Autonomy), Type of LED 20 Watt white LED Type,Ingress Protection IP 65 or Better,Indicator on The system - 2 LED Indicators Red and Green. 69 Providing and Fixing Pegwin Shape dustbin FRP 3 feet height, baok side door size 1 feet x 1 feet for removing garbage in fixing concrete etc. complete. 70 Providing and fixing road junction/ information sign boards of size 1.80 x 1.20 Meter Prepared 16 guage M.S.sheet on frame of size 40x40x5 mm with cross bracing of size 35x35 x 5 mm including painting with one coat of zinc cromate stoving primer and two coats each of green/white back ground and back side gray stove enamelled, bonded with red retro reflective sheet Engineering grade, border / letters / numeral /arrows, coated with non pealable crystal clear protective transperent coat retaining 100% reflection includingtwo angle iron post of size 65 x 65 x 6 mm of 3.65 m. long inflated at bottom drilled on top and painted in whiteand black bands of 30 cm. with 4 Nos. high strength G.I. bolts and nuts of size 10 mm dia. and 20 mm long sheet and angle iron post in one piece without joints including all taxes, conveying, fixing in ground with cement concrete 1:4:8 block of 60 cm x 60 cm x 75 cm size as directed by Engineer-in- charge etc. complete.Mild Steel Board with Engineering Grade. 71 Providing and fixing informatory sign boards of size 0.90 x 0.60 m made out of 14 guage Aluminum sheet bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including on frame of with angle iron frame of size 35 x 35 x 5 mm and two M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in 1:4:8 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Alluminium sheet Type IV High Intensity Micro Prismatic Grade Sheeting 72 Providing and Fixing Open Gym Equipment.Providing and fixing Sit Up Board made from B class Galvanized Iron. pipe. The main frame is of 25 millimeter Nota bene made from C Class Galvanized Iron. Pipe, Perforated sheet of 2 millimeter thickness is welded on main frame. The remaining frame of the sit up board is of 40 millimeter and 50 millimeter Nota bene made from C class Galvanized Iron. pipe. The foundation pipes are embedded in C.C. stock and painting is done by attractive color spraying after proper surface treatment, shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat. The top coat is done using the best quality brand paint or duly powder coated. 73 Providing and fixing Sky Walker made from B Class Galvanized Iron.Pipe. The main frame is Diameter 80 millimeter made from C class pipe. The outer ring of sky walker is Diameter 32 millimeter made from C Class Galvanized Iron Pipe. For connecting the handle frame to main pipe Diameter 60 millimeter C Class Galvanized Iron Pipe is used. The bottom support of Mild Steel, round plate of Diameter 250 millimeter X 10 millimeter thickness is welded at bottom. The leg movement frame is of 50 X 50 millimeter X 2 millimeter thick cyclic redundancy check square pipe. The handle frame is of Diameter 40 millimeter made from C* Class Galvanized. Iron Pipe. The foundation used for fixing is 80 X 40 millimeter X3 millimeter thickness C-Channel. The footrests is made from Aluminum casting material, its sizes are 130 X 310 X 5 millimeter Closing caps made from top quality Fibre-reinforced plastic material with 2 millimeter thickness and Plastic cap are used. The pins used bearing of reputed make (SKF/FAG). High tensile steel with galvanized nut bolts are used for assembly. The serclips used for assembly are of 25 millimeter The powder coat is done by Poly urethane and epoxy powder with 60 to 70 micron thickness. 74 Providing and fixing cross trainer made from B class Galyanized Iron.pipe. The center pipe is of 80 millimeter Nola bene made Tram C Class Galvanised Iron. pipe, and the bottom support of Mild Steel Round plate of 250 millimeter dare an a rat ho tomieter thickness is welded at bottom. The handle frame is made up 25 millimeter Nota bene C Class Galvanized Iron. Round Pipe. The foundation used for fixing is consists of three equal items that is. 100 millimeler Nota bene made from C Class Galvanised Iron. Round Pipo, Mild Steel Round Plate of 250 millimeter diameter and 10 millimeter thickness, 25 millimeter X 25 millimeter Mild Steel Angle of 3 millimeter Thickness. To join the Centre pipe and handle Frame Seamless Pipe of 50 millimeter origin destination and 3 millimeter Mild Steel Angle of 3 millimeter Thickness is used. For the movement, Bushes are used and for it 60 millimeter origin - destinatior and 3 millimeter thickness. The footrests is made from Fibre-reinforced plastic/C.1/Aluminum casting material, its size are 130 millimeter X 300 millimeter and 300 millimeter and 5 millimeter thickness. For support of Footrest of Cross trainer 130 millimeter X 300 millimeter with § millimeter thickness Mild Steel Plate and 50 millimeter X 50 millimeter cyclic redundancy check Square pipe with 3 millimeter thickness is used.Closing caps made from top quality Fibre-reinforced plastic material which is of 2 millimeter thickness. The pins used is made up of 25 millimeter diameter Harden bright bar. The bearings used are of 6205 permanent lubricated sealed bearing of reputed make. The handles used for cross trainer are of Rubber grip. The nut bolts used for assembly are made from S.S. material. The foundation pipes are embedded in C.C. stock and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated 75 Providing and fixing chest press made from B Class Galvanized Iron. Pipe. The Center Pipe is of 100 millimeter MB made from C Class Number Galvanised Iron. Round Pipe, and the bottom support of Mild Steel Round plate of 250 millimeter and 10 millimeter thickness is welded at bottom. The remaining frame is made up of 40 millimeter Not bene C class Galvanized Iron. Pipe. The handle frame is made up of 25 millimeter Nota bene C* Class Galvanised Iron. Pipe, The seat frame is made up of 40 millimeter Nota bene and 50 millimeter Nota bene C class Galvanized Iron. Pipe. For the assembly different bushes are used for fixing is consists of three equal items that is. 100 millimeter Nota bene made from C Class Galvanized Iron. Pipe, Mild Steel Round plate of 250 millimeter dia and 10 millimeter thickness and 25 millimeter X 25 millimeter X3 millimeter Mild Steel angle. The seats is fitted on the outer frame is made up of high quality Fibre-reinforced plastic material of size 330 millimeter X 330 millimeter of thickness 3 millimeter and Mild Steel Plate of thickness 5 millimeter and size 250 millimeter X 200 millimeter is used to support it. Closing caps are made from top quality Fibre-reinforced plastic material which is of 2 millimeter thickness. The pins used are made up of 25 millimeter and 17 millimeter dia solid bar. The bearing used are 6205 and 6203 permanent lubricated sealed bearing of reputed make. The nut bolt used for assembly are made from stainless steel material. The serclips used for assembly is of 25 millimeter diameter. The Poly Urethin plastic bush is used for handling. The foundation pipes are embedded in C.C. stock and painting is done by attractive color spraying after proper surface treatment, shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated 76 Providing and fixing Back extension made from B Class Galvanized Iron Pipe. The main frame of diametre 90 millimeter made from C Class Galvanized Iron Pipe, and the leg movement frame is of diameter 40 millimeter made from C Class Galvanized pipe. The handle frame is of diametre 32 millimeter made from C class Galvanized Iron Pipe. The seats is fitt a on the frame is made up of high quality FRP material of size 330 millimeter × 300 millimeter of thickness 3 millimeter and Mild Steel Plate of thickness 5 millimeter and size 250 millimeter × 200 millimeter is used to support it. The Foundation used for fixing is consists of 25 millimeter × 25 millimeter Mild Steel angle of 3 millimeter thickness. The footrests. is made from Aluminum casting material, its sizes are 130 millimeter x 310 millimeter x 5 millimeter. For the support diameter 32 millimeter made from C Class Galvanized Iron Pipe. closing caps made from top quality FRP material with 2 millimeter thickness. The powder coat is done by Poly urethane and Epoxy powder with 60 to 70 micron thickness. 77 Providing and fixing Rower made from B Class Galvanized Iron. Pipe, The main frame is 80 millimeter X 40 millimeter and 40 millimeter X 40 millimeter cyolio redundancy check Pipe with 2 millimeter thickness. The handle frame Is of 25 Nota bene made from C class Galvanized Iron. Pipe. The Foundation used for fixing consists of three equal items that is. 40 millimeter Nota benc made from C class Galvanized Iron. Pipe, C channel of 75 millimeter X. 40 millimeter X 5 millimeter and 25 millimeter X 3 millimeter Mild Steel angle. To join the movement frame to main frame seamless pipe of 50 millimeter diametermeter and 3 millimeter thickness is used. The seats which are fitted on the main frame is made up of high quality Fiber-reinforced plastic material of size 330 millimeter X 330 millimeter of thickness 3 millimeter and Mild Steel plate of size 250 millimeter X 200 millimeter X 5 millimeter is used to support it. Closing caps are made from top quality Fiber-reinforced plastic material which is of 2 millimeter thickness. The pins used are made up of 17 millimeter diametermeter hardened bright bar. The bearings used are of 6203 permanent lubricated sealed bearing of reputed male. The handles used are of Rubber grip. The nut bolts. used for assembly are made from Stainless Steel material. The bushes (Stoppet) used to avoid the collusion made from poly urethane plastic material of 50: millimeter diamefermeter The serclips used for assembly is of 17 millimeter diametermeter. The foundation pipes are embedded in Cement Concrete stock and painting is done by attractive color spraying after proper surface treatment, shot blasting and intial coat of yellow primer surface is plied before top coat. ithe top. coat is done using the best quality brand paint or duly powder coated. 78 Providing and fixing uneven bar made, from B class Galvanized Iron Pipe. The main frame is: 115 milliteter-diametermeter made from C class pipe and. the bottom support: of Mild Steei Round Plate of Diametermeter 250 millimeter and 10 millimeter thickness is welded at bottom. The handle frame istof diametermeter 40 millimeter made from C class Galvanized Iron Pipe. The foundation ised for fixing is consists of three equal item that is diametermeter 90 millimeter made from C Class Galvanized Iron, Mild Steel Round Plate of diametermeter 250 millimeter and 10 millimeter thickness and 25 millimeter × 25 millimeter mild steel angle of 3 millimeter thickness. Closing caps are made from top quality Fiber Reinforcement Plastic material which is of 2 millimeter thickness. The Powder coat is done by Poly urethane and epoxy powder coat with 60 to 70 micron thickness. 79 Providing and fixing Weight Lift as directed by engincer-in-charge 80 Providing and fixing combination leg press + standing twister + seating twister as directed by engineer-in-charge 81 Providing and fixing Air walker made from B class Galvanized Iron pipe. The center pipe is of 80 millimeter Notabene made from C Class Galvanized Iron pipe, and the bottom support of Mild Steel round plate of 250 millimeter diameter & 10 millimeter thickness is welded at bottom. The leg movement frame is of 40 millimeter NB made from C Class Galvanized Iron pipe. The handle frame is of 25millimeter Notaben made from C Class Galvanized Iron pipe. The foundation used for fixing is consists of three equal items i.c. 80millimeter Notabene made from C Class Galvanized Iron pipe, Mild Steel Round plate of 250 millimeter diameter & 10millimeter thickness & 25millimeter X 25millimeter Mild Steel angle of 3 millimeter thickness. To join the centre pipe & leg movement frame seamless pipe of 60 millimeter diameter & 3millimeter angle of 3millimeter thickness. To join the centre pipe & leg movement frame seamless plpe of 60mlllimeter diameter & 3millimeter thickness & 60millimeter thickness.. The footrests is made from FRP/Cast Iron /Aluminum casting Hamaterial, its sizes are 130millimeter X 300millimeter X Smillimeter. For the support 50millimeter X 50millimeter X millimeter CRC square pipe is used. Closing caps made from top quality Fiber Reinforced Plastic material with 2 millimeter thickness. The pins used are made up of 25 millimeter diameter bright bar. The bearings used are6205 permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from Stainless Steel material. The serclips used for assembly are made from Stainless Steel material. The serclips used for assembly are of 25millimeter diameter. The foundation pipes are embedded in Cement Concrete, stock and painting is done by attractive color spraying afler proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint orduly powder coated 82 Providing and fixing Parallel bar of height 1.3 meter Galvanised Iron Pipes of A Class quality. The frathe of the parallel bar shall be of 40 milimeter Nominal Bore pipe. The vertical support pipe shall be embedded with holdfast in Cement Concrete:block of 0.3.X 0.3 X:0.3 meter below ground level. The total play area for the equipment shall be 0.9 X 0,5 meter painting is done by spraying after proper surface treatment and an initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated. 83 Providing and fixing Super Max Multi Play System made for roto moulded FRP 4 Tanel slide 1.9 feet dia, with FRP panel made for roto moulded FR$ Tanel Spiral Slide 1.50 metre height, 6 feet length tanel bridge, FRP Panel, canopy made for roto moulded FRP size 3 x 3 feet with 7 feet length ladder including railing 25 millimeter NB Pipe, 10 feet height 80 millimeter diameter Tower Pol, 2milimeter thick platform percoated sheet size 3 x 3 feet, High Tension Blackning, Tanel Slide leg 40 millimeter pipe, Spiral slide main support 75 millimeter dia 5 feet length, all mild steel material used in P.P. Grade powder coating with forpeting process excetra complete 84 Providing and fixing Double Swing with 9 feet leg using 38 millimeter NB Pipe, 10 feet: Top Bar lengch 50 milimeter ISI Mark NB Pipe, Rubber Coated Chain with Suspension, attached rubber sheet, including S type Hook, moulded bearing clarap, P.P. grade powder coating with fospeting complete. including welding and handling charges with mild steel pocket excetra complete. 85 Sub Work No. 10 - Afforestrtion / Plantation -Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means 86 Filling fresh garden soil /silt & manure in excavated area including lead upto a distance of 50 mtrs (1/10 of unskilled labour) 87 Preparing Lawn:- Excavating the ground to a required depth of 30cms.removing & conveying unwanted stuff to a required distance as directed. Filling fresh garden soil & manure are in 3:1 proportion to a height of 20cms. Mixing garden soil and manure thoroughly, well, levelling, watering on previous night. Planting required variety of lawn grass (Cynadon or paspallum) as directed and maintaining till well established by watering, weeding, clipping, rolling etc.complete 88 Preparing flower bed :- Hibiscus (8 x 10) Excavating the ground to required depth of 30cms removing and conveying unwanted stuff to a required distance as directed. Filling fresh garden soil & Manure in excavated area in 3:1 proportion to a height of 40cms. Mixing garden soil & manure thoroughly well, levelling, watering on previous night. Planting well rooted shrubs 0.5 meters apart as directed and maintaining till well established by watering,weeding, stirring, replacing casualties etc.complete. 89 Preparing Shrubbery :- Plumeria Rubra (21 x 21) Excavating the ground to required depth of 30cms removing and conveying unwanted stuff to a required distance as directed. Filling fresh garden soil & MAnure in excavated area in 3:1 proportion to a height of 30cms.Mixing O garden soil & manure thoroughly well, levelling watering on previous night. Planting well rooted shrubs 0.5 meters apart as directed and maintaining till well established by atering,weeding, stirring, replacing casualties etc.complete 90 Mogra Plant/Creepers /Climbers -Excavation pit with size 0.30x 0.30x 0.30 removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 0.15 mt with fresh garden soil and manure in 3:1 propration.Mixing soil and manure thoroughly well levelling,watering on previous night .planting one or two year old healty plant as per specification Maintaning till well established by watering etc,complet , weeding pruning, sirring replacing casualties. Gardenia Lasmirals (Motha Mogara) 8 x 10 91 Jasmin (Mogara) 8 x 10 92 Planting large flowering /shady trees (ht.1.00 mt): Digging pit with size 0.9 m x 0.9 m x 0.9 m, removing and conveying unwanted stuff to a required distance as directed Filling the pit with approved excavated material upto to a height of 0.30 m and reamaining height of 0.60 m. with fresh garden soil and manure in 3:1 proporation mixing soil and manure throughly well leveling, as directed watering, previous night, planting two to three year old minimum 1.00 mtr height, helthy trees spaling as per specefications, Maintaing till well established by watering weeding,sirring of soil replacing of casualties etc complete, Delenia indica (Green Chafa) 21 x 21 93 Planting large flowering /shady trees (ht.2.00 mt): Digging pit with size 0.9 m x 0.9 m x 0.9 m, removing and conveying unwanted stuff to a required distance as directed Filling the pit with approved excavated material upto to a height of 0.30 m and reamaining height of 0.60 m. with fresh garden soil and manure in 3:1 proporation mixing soil and manure throughly well leveling, as directed watering, previous night, planting two to three year old minimum 2.00 mtr height, helthy trees spaling as per specefications, Maintaing till well established by watering ,weeding,sirring of soil replacing of casualties etc complete. Delonix Regia (Gulmohar) 14 x 16 94 Planting small and medium size ornamental /flowering plant Planting small and mediumsize ornamental or flowering plant. Digging pit with size 0.6 m x 0.6 m x 0.6 m, removing and conveying unwanted stuff soil and Farm Yard Manure up to a height of 0.60 m in 3:1 proportion, mixing soil and manure thoroughly well, leveling and watering previous night. Planting one or two year old healthy plant saplings as per specifications. Maintaining till well established by watering. Stirring of soil and manure, replacing of casualties etc. completePeepal 8 x 10 95 Rubber Plant 10 pot 96 Moringa (Shevga) 5 x 6 97 Sonchafa 8 x 10 98 Supply and installation of drip irrigation system all along the plantation /lawn area including all components and accessories etc complete 99 Bamboo Golden 13 x 13 - Excavation pit with size 0.30x 0.30x 0.30 removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 40 cm with fresh garden soil and manure in 3:1 propration.Mixing soil and manure thoroughly well levelling,watering on previous night .planting one or two year old healty plant as per specification Maintaning till well established by watering etc,complet , weeding pruning, sirring replacing casualties 100 Evergreen perennial typically grown- Excavation pit with size 0.25 x 0.25 x 0.25 removing and conveying unwanted stuff to a required distance as directed. Filling the pit with approved excavated material upto a height of 80 cm with fresh garden soil and manure in 3:1 propration.Mixing soil and manure thoroughly well levelling,watering on previous night .planting one or two year old healty plant as per specification Maintaning till well established by watering etc,complet , weeding pruning, sirring replacing casualtiesCanna (Kardal) 5 x 6 101 Snake Plant 10 pot 102 Arecaplam 13 x 13 103 Spider lilly 5 x 6 104 Weeping Fig 6 pot 105 Tulsi 5 x 6 106 Providing labour for plantation of different types of plants and trees, include excavating pit, watering the plant etc. Complete Mali 107 Mazdoor - Unskilled Heavy Male 108 Tree Cutter - Semi Skilled
