Tender For Provision Of 06 X Toilets At Astroturf Ground Katoch Stadium, Special Repairs To Roof Of Building No P-14, 15, 16 And 17 Of Hq 11 Corps Camp And Other Sanctioned Works Under Ge (West) Jrc.; 1 Surface dressing not exceeding15 cm deep and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-Charge. 2 Excavating over areas not exceeding 1.5m deep and getting out in soft/loose soil, complete all as specified and directed by Engineer-in-Charge. 3 All as per item No 2.00 above but depth exceeding 1.5m and not exceeding 3.00m, complete all as specified and directed by Engineer-in-Charge. 4 Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes, sewage line, laying of pipe of 40mm etc. and getting out in soft/loose soilcomplete all as specified and as directed. 5 M&L for cement concrete type D2, 1:4:8 (using 40mm graded aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-Charge. 6 M&L for RCC design mix M-25 concrete (using 20mm graded stone aggregate), as in Foundations, including rafts, footings, foundation beams; plinth beams; base for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-Charge. 7 M&L for RCC design mix M-25 concrete (using 20mm graded stone aggregate), as in Columns, pillars, piers, posts and struts, complete all as specified and directed by Engineer-in-Charge. 8 M&L for RCC design mix M-25 concrete (using 20mm graded stone aggregate), as in roof beams, cantilevers, bressummers, lintels upto and over 1.5 m clear span, complete all as specified and directed by Engineer-in-Charge. 9 M&L for RCC design mix M-25 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engineer-in-Charge. 10 Use & waste formwork for fair finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping), complete all as specified and directed by Engineer-in-Charge. 11 Use & waste formwork for rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed by Engineer-in-Charge. 12 Use and waste formwork for fair finished surfaces tosquare/reactangular sides of pillars, posts, struts, piers, columns, and stanchions fair and finished surface, complete all as specified and directed by Engineer-in-Charge. 13 Use & waste formwork for fair finished surfaces to sides and soffits of floor or roof beams, beam, RCC coping fair and finished surface, complete all as specified and directed by Engineer-in-Charge. 14 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to, complete all as specified and directed by Engineer-In-Charge. 15 All as per item No 14.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders, complete all as specified and directed by Engineer-In-Charge. 16 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed by Engineer-In-Charge. 17 M&L for Brick work with sub class B bricks using old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed. 18 M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-In-Charge. 19 M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls, finished fair and even, complete all as specified and directed by Engineer-In-Charge. 20 M&L for preparation of new plastered surfaces and distempering walls with two coats of distemper oil emulsion, white or tinted over and including 1mm thick wall care putty including primer, complete all as specified and directed by Engineer-in-charge. 21 M&L for preparation of new plastered surfaces and applying two coats of exterior emulsion paint over and including a coat of primer, complete all as specified and directed by Engineer-in-charge. 22 Material and labour for pre-construction antitermite treatment by treating the top surface of filled earth at the rate of 5 litres of ATT emulsion per Sqm of surface area, complete all as specified and directed by Engineer-in-charge. 23 Material and labour for pre-construction antitermite treatment by treating the soil under plinth ptotection at the rate of 5 litres of ATT emulsion per Sqm of surface area, complete all as specified and directed by Engineer-in-charge. 24 Material and labour for pre-construction antitermite treatment by treating the soil alongwith external perimeter of bldg at the rate of 2.25 litres of emulsion per metre of the wall, complete all as specified and directed by Engineer-in-charge. 25 M&L for hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed by Engineer-in-Charge. 26 M&L for 75mm thick cement concrete type C2 1:4:8 (40mm graded stone aggregate) in sub base, complete all as specified and directed by Engineer-in-Charge. 27 M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engineer-In-Charge. 28 M&L for coloured glazed ceramic tiles7-8 mm thick, area of each tiles not exceeding 0.36 sqm in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in white or colour cement to match , complete all as specified and directed by Engineer-in-charge. 29 M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over and including 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite,rounding to edges complete all as specified and directed by Engineer-In-Charge. 30 Spreading, leveling, watering and well ramming in layers not exceeding25cm for soft/loose soil, complete all as specified and directed by Engineer-in-Charge. 31 Returning filling including spreading, leveling, watering and well ramming in layers not exceeding25cm for soft/loose soil, complete all as specified and directed by Engineer-in-Charge. 32 Removing excavated materials (soil) not exceeding 50m and depositing where directed of a level not exceeding 1.5m above the starting point, complete all as specified and directed by Engineer-in-Charge. 33 M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in plinth protection finished even and smooth (without using extra cement), complete all as specified and directed by Engineer-In-Charge. 34 S&F solid PVC frame as in door, of size 50mm x47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube and edges will be painted to match with printed sheets, suppyling & fixing in opening as per specification & drawing, complete all as specified and directed by Engineer-In-Charge. 35 S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; & 5mm thick x 15mm wide PVC sheet beading use inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree)used.Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engineer-In-Charge. 36 Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 37 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 38 S&F stainless steel steel butt hinges cold rolled of size 100mm medium weight, complete all as specified and directed by Engineer-In-Charge. 39 S&F Aluminium anodised,barrel tower bolts 150mm long of extruded section and fixed, complete all as specified and directed by Engineer-In-Charge. 40 S&F Aluminium handles, cast type anodised of size 150mm etc, complete all as specified and directed by Engineer-In-Charge. 41 S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed by Engineer-In-Charge. 42 S&F powder coated (thickness or powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, sliding type or fixed type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) etc. in each shutter. complete all as specified, complete all as specified and directed by Engineer-In-Charge. 43 S&F anodised Aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. 44 S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, complete all as specified and directed by Engineer-In-Charge. 45 S&F 4mm thick figured glass, pin headtype and glazing with oil putty in square not exceeding 0.5 sqm in each pane, complete all as specified and directed by Engineer-In-Charge. 46 S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 Complete all as specified and directed by Engineer-in-Charge. 47 S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed by Engineer-in-Charge. 48 S&F mild steel plates, plain or chequered, 6mm thick or over in thickness in available sizes, complete all as specified and directed by Engineer-in-Charge. 49 M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer, complete all as specified and directed by Engineer-In-Charge. 50 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour and finished with resin coat on both surfaces @150gm/Sqm of coating having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge. 51 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engineer-In-Charge. 52 S&F PVC water tank of capacity 2000 Ltr and S&F new rotational moulded polyethylene water storage tank of capacity2000 ltr (cylindrical vertical with closed top) hoisted and fixed in position all as specified including 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed by Engineer-In-Charge. 53 S&F in gun-metal, globe or gate valves for 20mm bore dia of pipe, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe orunion, , complete all as specified and directed by Engineer-In-Charge. 54 S&F Steel Tubes Medium Grade Bore of tube in 15mm galavanised with all fitting laid in trenches, walls, ceiling or laid in floors etc, complete all as specified and directed by Engineer-In-Charge. 55 All as per item No 54.00 above but of size of 20mm bore, complete all as specified and directed by Engineer-In-Charge. 56 S&Fvitreous china counter top Wash Basin, snow white, oval type of size 490mm x 400mm x 150mm including long body pillar tap of height not less than 300mm, waste pipe, coupling etc, complete all as specified and directed by Engineer-in-charge. 57 S&F wall mounted sensor equipped liquid soap dispenser of minimum capacity 350ml, complete all as specified and directed by Engineer-in-charge. 58 Supply and fix 8mm thickElegant arts Frame black synthetic Wood bath mirror one piece of specified sizefixed to wall, complete all as specified and directed by Engineer-In-Charge. 59 S&F in vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices with recessed bottom, jet spray, etc, complete all as specified and directed by Engineer-In-Charge. 60 S&F in low level flushing cistern PVC valveless syphonic action type, 10 ltrs capacity including supply pipe & fixing brackets of M.S. angle of size (25mmx25mmx3mm), 30 cm long in PCC (1:2:4) type B-1, block of size (10cmx10cmx10cm) on walls etc, complete all as specified and directed by Engineer-In-Charge. 61 S&F in repairs vitreous china Urinal, Half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, complete all as specified and directed by Engineer-in-charge. 62 S&Fvitreous china urinal partition white of size 310x700 mm, complete all as specified and directed by Engineer-In-Charge. 63 S&F 15mm dia Chromium plated fancy type bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe and fixed to 15mm bore pipe fixed, complete all as specified and directed by Engineer-In-Charge. 64 S&Ffancy type, brass chromium Platedstop valves/Angle valves, cast copper alloy, bore dia of pipe in 15mm, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe and fixed, complete all as specified and directed by Engineer-In-Charge. 65 S&F PVC connection 15mm size with brass check nuts of length 450mm etc, complete all as specified and directed by Engineer-In-Charge. 66 S&F SS waste coupling including waste pipe suitable for WHB/ urinals, bore dia of discharge pipe 32mm of PTMT (half or full threaded), (Minimum weight 45gms), complete all as specified and directed by Engineer-In-Charge. 67 S&F stainless steel toilet paper holder with gutties and steel screws on walls as directed and approved complete all as specfied 68 S&F in repairsbrass chromium plated health faucet for pedestal pattern water closet includingPVC flexible pipealongwith complete necessary fittings all as specified and directed by the Engr- in- Charge. 69 S&F in repairsbrass chromium plated jet for pedestal pattern water closet includingPVC flexible pipealongwith complete necessary fittings all as specified and directed by the Engr- in- Charge. 70 S&F urinal spreader of brass chromium plated any colour for fixing with 15 mm dia pipe, complete all as specified and directed by Engineer-In-Charge. 71 S&F grating doom 100mm dia with waste hole ofCP, complete all as specified and directed by Engineer-In-Charge. 72 S&F PVC (SWR) floor trap of 110mm outlet dia, plain with grating including jointing with solvent cement, complete all as specified and directed by Engineer-In-Charge. 73 S&F 110mm bore PVC (SWR) bends any radius, complete all as specified and directed by Engineer-In-Charge. 74 S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed by Engineer-In-Charge. 75 S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints,fixed to wall complete all as specified and directed by Engineer-In-Charge. 76 S&F stack clamps for bore dia of pipe 75mm, made out of 50 mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specified and directed by Engineer-In-Charge. 77 S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed by Engineer-In-Charge. 78 S&F false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595x595 mm of approved texture, design and pattern having moisture content not less than 2% humidity resistance of 99%. NRC 0.50 to 0.75 as per IS 8225: 1987, non-combustible as per BS 476 (Part-4)- 1970 and light refletance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120 grams per Sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000mm, cross- T size from 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600 mm to form grid module of 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per Sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasterners, 6 mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length-3000 mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles. The work shall be carried out as per specifications, drawing and as per directions of Engineer-In-Charge. 79 Excavation in trenches exc. 1.5 m wide and n. exc. 3.0 m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes, sewage line etc. and getting out in soft/loose soilcomplete all as specified and as directed. 80 Material and labour for 200mm bore salt glazed stone ware drain pipes (Grade-A)laid in trenches and jointed in CM 1:1 and tested complete all as specified and directed. 81 Material and labour forPCC (1:3:6) type C-2 using 40mm graded stone aggregate as in concrete bed to 200mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. 82 Material and labourfor providing PCC (1:2:4)type B-1 (using 20mm graded stone aggregate) as in coping, channel,benching/ haunching of manhole, drain, laid to shape and slope, slightly rounded or chamfred angle and throating including necessary form work etc complete all as specified and directed. 83 M&L RCC Septic tank for 100 users capacity all as specified and as directed. 84 M&L soakage wells (size 2.4m dia x 3.00 m effective depth ) excavation, in any type of soil, foundation in PCC 1:3:6 walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/ DWC complete filled with brick bats of size complete all as specified and directed 85 M&L 25 mm sand filling under floor or in foundations / interlocking tiles including watering and consolidation complete all as specified and as directed. 86 M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade and fixed with grey cement and pigment complete all as specified and directed. 87 M & L for providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sides of rounded or chamfered on edges of hardstanding complete all as specified and as directed. 88 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof) all as specified. 89 M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stillgreen finished even and fair including mixing ofwater proofing compound as per manufacturer instructionetc complete all as specified and as directed. Note :- Water proofing compound shall be measured separately. 90 Supply only Liquid water proofing compound complete all as specified and as directed of as per manufacturer instruction. 91 Material and labour for 3mm thick superior APP (Atactic poly propylene) modified polymeric membrance waterproofing treatment of weight not less than 3.6 Kg per sqm with properties of high penetration and the centre core consisting of 90 micron high Molecular-High Density polyethylene (HMHDPE) film consisting of five layers. The superior multipolyplus is to be laidafter preparing the surfaces by cleaning thoroughly to achieve a smooth surface over and including a coat of bitumen primer @ 0.30 Litre per sqm over a coat of hot applied Blown Bitumen of grade 85/25 @ 1.2 kg per sqm. The overlaps between supermulti polyplus areminimum 10cm seam in width/lengthwise complete all as specified and all as per manufacturer’s directions. 92 Taking up or down existing steel 15 mm tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed. 93 Taking up or down existing steel 20 mm tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed. 94 Supplying and fixing, 15 mm jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall (including cutting chases for concealing the GI pipe and making good complete) or laid in floor complete all as specified and as directed. 95 Supplying and fixing, 20 mm jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall (including cutting chases for concealing the GI pipe and making good complete) or laid in floor complete all as specified and as directed. 96 Dismantling of water tanks (PVC/RCC of any description) n exc 500 ltr capacity and removing from site complete all as specified and as directed 97 S&F 500 ltr capacity rotational moulded polythene tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. Make Sintex/Polytuf 98 S&F20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms ), complete all as specified and directed 99 S & F in repair 15 mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. 100 Taking down cement plaster of any descriptionany thickness /dado/Skirting/ including raking out joints hacking for key scrubbing down with water all as specified. 101 Demolition of brickwork or stone/boulder masonry, build in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles incl removing mortor and cleaning serveciable bricks 102 M&L forpreparing new plastered or unplastered wall surfaces and appliedtwo coat of cement base paint over one priming coat all as specified and directed by Engr-in-charge. 103 Demolition and breaking up drain pipesAC/PVC pipe in event n.exc 150 mm dia including all fittings. 104 S & F 110 mm bore PVC (SWR) pipe of pressure rating 6kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive fixed in repair to wall/laid in trenches complete all as specified and directed. Make : Prince /Supreme 105 S&F PVC (SWR) junction single (single tee)equal or unequal, dia of pipe 110 mm completeall as specified and directed. 106 Surface excavation n exc 30 cm deep and averaging 15cm deep in hard/dense soil 107 M&L for cement concrete type C-2 1:3:6 with 40mm graded aggregate of 75 mm thick as in sub-base 108 M&L forproviding PCC (1:3:6) type C1 using 20mm graded aggregate as in kerbs mud stops rounded or chamfered on edges of path straight or curves 109 M&L Cement concrete type C-2 , 1:3:6 ( Using 40 mm graded stone aggregate foundations,filling and mass concrete 110 M&L machine pressed precast coloured concrete coloured interlocking paver blocksany shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment. 111 M&L Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard dense soil. 112 M & L for PCC (1:2:4) type B-0 (using 12.50 mm graded crushed stone aggregates ) lean concrete as in foundation, filling and mass concrete of post complete all as specified. 113 S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to grade Fe-410-W complete all as specified and directed by EIC. 114 M&L forpreparing newly plastered or unplastered wall surfaces and appliedtwo coat of cement base paintover one priming coat complete all as specified and directed by Engr-in-charge. 115 S&F 35 mm thick ( measured solid) precast cement concrete (1:2:4) type B-0 (using 12.5) mm graded stone aggregate) as in louvers or jallies set in cement mortar (1:4) includingall necessaryfromwork and reinforcement & dismantling the existing jalli of any description & any description complete all as specified and directed by Engr-in-Charge 116 Material & LabourFramed work as in Ornamental gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastenig Fe-410-W (Gdequality A) 117 Excavation in post holes (or similar holes) each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc 25 cm watering and removing surplus soil to distance n. exc 50m and making good surfaces in soft/loose soil 118 M&L for cement concrete type B2 (1:2:4) in foundations, filling and mass concrete using 40mm graded stone aggregates 119 Surface excavation n.exc 30 cm deep and averging 15cm deep and getting out in soft/loose soil 120 M&L for 60 mm thick machine pressed precast concrete interlocking tiles any shape, size, colour/pattern(as approved) confirming to IS 15658-2006 of M-35 Grade complete all as specified. 121 M&L for point wiring with 1.5 Sqmm, PVC insulated FRLS, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia(Minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and modular metal flush mounting box withwhite cover plate with frame of suitable number of module as required at site, brass/cadmium plated steel screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated FRLS cable green in colour as continous earth conductor connected to common earthdolly with all accessories complete all as specified and directed for :-(a) One 3 pin socket outlet, 5Amps, independent board 122 (b) one 3 pin socket outlet 5 amps on same board with other switches. 123 (c) One light /fan/cell bell point controlled by one one way switch as directed engineer-in-charge 124 M&L for point wiring with 2.5 Sqmm, PVC insulated FRLS, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia(Minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and modular metal flush mounting box withwhite cover plate with frame of suitable number of module as required at site, brass/cadmium plated steel screws and cup washers including 2.5 Sqmm multi stranded copper conductor PVC insulated FRLS cable green in colour as continous earth conductor connected to common earthdolly with all accessories complete all as specified and directed for one light point/fan/bell controlled by one switch SP one way. 125 Supply and fixing modular type 2 module type switch 1 way 16A, 126 Supply and fixing Modulartype socket 5 pin16 amp 127 Supply and fixing Modular type switch 1 way 6A, 128 Supply and fixing Modular type socket 5 pin6 amp 129 Supply and fixing modular metal flush box4 modular complete all as specified and directed. 130 Supply and fixing modular metal flush box6 modular complete all as specified and directed. 131 Supply and fixing modular white cover plate with frame ,4 modulecomplete all as specified and directed. 132 Supply and fixing modular white cover plate with frame ,6 modulecomplete all as specified and directed. 133 Supply and fixing modular white cover plate with frame ,1/2 modulecomplete all as specified and directed. 134 M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. 135 S&Fin repairs/replacement Sheet metal enclosure for DBs when MCBs to be used, SPN 8 ways 240 V, with copper bus bar, double door, epoxy/powder coated inside and outside complete all as specified. 136 M&L in replacement MCB SP 6 Amps to 32 Amps, 240V with rupturing capacity 10 KA, C Curve complete all as specified 137 Supply and fixing amp rating 240V, 10KA C curveminiature circuit breaker (MCB) SPN 32 AMP of following polesand current carrying capacity in the MCB DB complete with connection testing andcommissioning. SPN 32 AMP 138 S&F LED tube light fitting 20W (Double side) including LED lamp 20W with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50mm 4 core complete all as specified and directed. 139 S&Flamp holder, pvc /polycarbonate type with back plate suitable for batten fitting 140 Supply & fixing exhaust fans metal body AC single phase 230/ 240 V of size 300 mm sweep with louver and including making of hole/opening in wall complete all as specified and directed. 141 Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermalmanagement in multiple optics complete withIP 65/66 protection complete 142 M&L in repairs Submain wiring with two run of FRLS PVC insulated unsheathed multistranded copper conductorsingle core 6 Sqmm drawn through in and including PVC rigid non metallic surface or concealed conduitmedium grade with all fittingsincluding earth continuitycopper conductor 6 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor with green insulation complete all as specified including taking down existing unserviceable/burnt submain. 143 M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed.Note: (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt. 144 Supply, installation & commissioning MCB Load Distribution board VTPN 4 way double door, for mountingMCCB/DP/ SP/TP/ MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DP/SP/TP MCB shall be of same make as DB. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site. 145 Supply and Fix, MCCB 3 Pole 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 KA adjustable, 50 Hz, 415 V with rupturing capacity 36 KA. 146 M & L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 16 sq mm 4 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge. 147 Supply and lay pipe galvanized medium class including fitting 32 mm dia. 148 Supply and lay pipe galvanized medium class including fitting 25 mm dia. 149 Supply and fix valve, stop, screwed 25 mm dia pipe Stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fix 150 Supply and fix valve, stop, screwed 32 mm dia pipe Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fix 151 M&L for drilling and tapping cast iron water mains for branch connection of internal dia 152 M&L for for run lead joint including provisionof spun yarn for spigot and socketed CI pipes /fitting of size 100MM mm bore completed all as specified
