|
| 1 | Providing and fixing of panels for wall and roof. The roof shall be provided 50mm thick puff insulated panel make Sintex or 0.50m thick precoated precoloured sheets. The roof sheet are laid over a frame work of trusses and purlins and rafters fixed using suitable fasterers. A 0.50mm precoated/ precoloured steel sheets ridge cover of 0.40mm from the eves wall and 0.30mm from the gable wall. The wall shall be made in sandwich panel systsm using 2No\"s of precoated precoloured sheets of 0.50mm thick fitted fitted with 50mm thick puff with bulk density of 40kg/cum. The puff panels shall be make Sintex/Llyod/Jindal contineous panel system. The panels shall be inserted one by one in \"U\" shaped ground track of size 52.5x35x1.25mm thick made from G.I sheet/sheet coil. The bottom track shall be fixed to the concrete platform level by suitable fasteners screwed on the PVc expandable screw cap. The top of the walls would be concealed with \"U\" shaped top track of size52.5x35x1.25mm thick made from G.I sheet/sheet coil. The roof shall be 1:4 approximately as per seismic Zone -IV . The walls height shall be 3Mts at eves and 3.36 Mts at centre gable. Structural steel work rivted and bolted in built up sdection trusses and frame work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades,in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. Size of tile 600x600 mm along with scredding below it.Providing and fixing tiled False Ceiling of specified materials 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thickof inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Including necessary electrification and allied works such as construction of independent staging as per the directions of EIC(Complete Job) |
| 2 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 2.9.1 All kinds of soil : |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form work for: Foundation etc |
| 7 | Suspended floors, roofs, landings, balconies and access platforms. |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level TMT |
| 9 | Providing and fixing white viterious China pedestal type water colset (European type W/C pan) with seat and lid 10liters low level white P.V.C flushing Cistern including flush pipe with manually controlled device(Handle lever) confirming to I.S 7231 with all fittings fixtutres complete and making good the walls and floors whereever required W.C pan with ISI marked white soild plasiic seat and lid (CERA/HINDWARE) |
| 10 | Providing and fixing white viterious China wash basin CI/MS bracket 15mm brass CP piller taps 32mm CP brass waste of standard patternincluding painting of cutting and making good walls floors wherever required ze 600x450. (CERA/HINDWARE) |
| 11 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. |
| 12 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 13 | Providing and fixing PTMT soap dish holder having length of 138mm, breadth of 102mm height of 57mm with concealed fitting arrangement, weighing not less then 106gmgs. |
| 14 | Providing and fixing towal rail complete woth brackets fixed to woden cleat with CP brass (2No\"s) screws with concealed fitting arrangment of approved quality and colour (450mm long towel rod with total length of 195x78mm wide anf effictive height of 88mm weighing not less then 170gms |
| 15 | Providing and fixing mirror of super glass(of approved quality) and of reqiuired shape and size with plastic moulded framed of approved make amd shade with 6mm thick hard board backing (Rectangular shape 453x357mm) |
| 16 | Providing and fixing CP brass Nose bib cock of approved quality confirming to ISI standrad and weighing not less then 810gms, 15mm nominal bore (approved by Engineer-in-Charge (Jaguar, Marc or equivalent) |
| 17 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 15mm nominal outer dia pipes. |
| 18 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 25mm nominal outer dia pipes. |
| 19 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 32mm nominal outer dia pipes. |
| 20 | Providing and fixing wall face un-plastered rigid PVC water pipes including jointing the same. (75mm dia) |
| 21 | Providing and fixing wall face un-plastered rigid PVC water pipes including jointing the same. (110mm dia) |
| 22 | PVC water Tank of 1000Lt ISI mark (01No) with independent staging |
| 23 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 610x460mm bowl depth 200mm |
| 24 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 25 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete 32 mm dia |
| 26 | Providing and fixing 100 mm sand cast iron grating for gully trap. |
| 27 | Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. |
| 28 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 29 | providing and laying river bed material on the road surface by way of spreading the same in uniform layer not exceeding 20cm in depth , watering and compacting with vibratory PRR of 8-10 tonne capacity complete) including carriage of material from source to site of work (all lead lift |
| 30 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 31 | 12mm Cement plaster finished with a floating coat of neat cement of mix: 13.7.1 1 : 3 ( 1 cement : 3 fine sand) |
| 32 | Carriages of material by M.T including loading, unloading complete Sand Avg Lead 10 kms |
| 33 | Stone below 40 mm Avg Lead 10 kms |
| 34 | Brick avy lead 25 km Please Enable Macros to View BoQ information |
