Tender For Construction Work Of An Auditorium With A Capacity Of 800 Persons On 10,000 Sq. Meter Vacant Land In The Government Inter College Campus Near Mahavir Chowk In Muzaffarnagar District Under The Jurisdiction Of Development Authority Muzaffarnagar., Muzaffarnagar-Uttar Pradesh

TDR : 52095564

Tender Notice
BOQ

Expired

Muzaffarnagar , Uttar Pradesh

Tender Brief : Tender For Construction Work Of An Auditorium With A Capacity Of 800 Persons On 10,000 Sq. Meter Vacant Land In The Government Inter College Campus Near Mahavir Chowk In Muzaffarnagar District Under The Jurisdiction Of Development Authority Muzaffarnagar.

Document Fees
₹ 11800 /-

EMD
₹ 4427000.0 /-

Tender Value
₹ 22.13 Crore /-

Submission Date
13-11-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	EXCAVATION WORK
2	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil
3	Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil
4	1.50 -3.0m
5	Diluting and injecting chemical emulsion for post-constructionai anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With chlorpyriphos/lindane E.c. 20% with 1% concentration
6	Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
7	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.
8	Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
10	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).
11	Providing & applying a coat of residual petroleum bitumen of grade of Vg-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
12	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work;usingcoarse aggregate and fine aggregate derived from natural sources,portland pozzolana / ordinary portland /portland Slagcement,admixtures in recommended proportions as per iS: 9103 to accelerate /retard setting of concrete, to improve durability andworkabilitywithout impairing strength; including pumping of concrete to site of laying, curing,carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge;for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. concrete of M25 grade withminimum cement content of 330 kg /cum
13	All works upto plinth level Concrete of M25 grade withminimum cement content of 330 kg /cum
14	All works upto plinth level Concrete of M30 grade withminimum cementcontent of 350 kg /cum
15	All works above plinth level upto floor V level. Concrete of M25 grade withminimum cementcontent of 330 kg /cum
16	All works above plinth level upto floor V level. Concrete of M30 grade withminimum cementcontent of 350 kg /cum
17	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
18	Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine
19	Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.
20	Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete
21	Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
22	Centering and shuttering including strutting, propping etc. and removal of form forWalls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
23	Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick
24	Centering and shuttering including strutting, propping etc. and removal of form for Shelves (cast in situ)
25	Centering and shuttering including strutting, propping etc. and removal of form for Weather shed, chajjas, corbels etc., including edges
26	Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick
27	Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide
28	Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (plan area to be measured). Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)
29	Centering and shuttering including strutting, propping etc. and removal of form for Cornices and mouldings
30	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
31	Extra for plastering done on moulding, cornices or architraves including neat finish to line and level: In one coat
32	Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-iii) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.
33	Providing & Fixing Materials GRC Materials Jali upto 35-40mm thick as per Drawings Approved by Site in-charge
34	Providing & Fixing GRC Tree Size upto Length 4.00xHeigh4.00mtr.as per Drawings Approved by Site in-charge
35	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade FE-500D or more.
36	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. asrequired. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
37	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
38	Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet conforming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately).
39	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
40	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
41	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar I:4 (l cement : 4 coarse sand)
42	Providing and laying Autoclaved Aerated concrete(AAC) blocksmasonry with 150mm to 300 mm thickwith Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3)in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
43	Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.
44	FINISHING WORK
45	12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)
46	6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
47	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
48	Surface Preparation - Exterior surface cleaning / Sanding using recommended tools.
49	Home Sheild Waterproof Putty – Applying 2 coat of the HS Waterproof Putty is a premium quality white cement-based putty that is damp proof and has some unique properties ,Cured surface after waterproofing with wall putty provides excellent hydrophobicity, exhibiting “Lotus Bead” effect
50	Damp Stop Duo Primer - Applying 1 coat of HomeShield Dampstop Duo primer using a Graco sprayer is a fast and efficient way to get a smooth, even base coat.it is a specially formulated premium quality acrylic primer with superior alkali, damp and efflorescence resistance properties both from positive and negative sides of the wall. Long lasting waterproofing warranty of 7 years on Exterior wall application & 2 years on Interior wall application (T&C applied)
51	Exterior with Longlife 10- Applying 2 coats of Long Life 10 Luxury Exterior paint using a Graco sprayerluxury high-performance exterior emulsion specifically formulated for long-lasting protection and aesthetic enhancement of external surfaces. This product features advanced PU Silicon Technology, offering superior performance under extreme weather conditions and upto 40% dilution on suitably primed/basecoat applied or painted internal walls and ceilings by roller, brush or spray as per manufacturers recommendations.
52	Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminatedglass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, allcomplete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
53	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than50 gram/litre
54	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
55	Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
56	Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall bemoulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS havingelectronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.
57	FLOORING WORK
58	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
59	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
60	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)jointing with grey cement slurry @3.3 kg/sqm includingngrouting thejoints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile600 x 600 mm
61	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundybottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
62	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architecturaldrawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent
63	Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with and admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade
64	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm
65	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite work)
66	Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
67	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
68	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
69	Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Makrana white second quality
70	Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :Light shade pigment using white cement
71	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread offlame of Class A categorywith property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and lengthcomplete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance indimensions i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 100 mm
72	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimumcompressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread offlame of Class Acategory with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick
73	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorativetype, core of block board construction with frame of 1st class hard wood and well matchedteak 3 ply veneering with vertical grains or cross bands and face veneers on both faces ofshutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
74	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
75	Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
76	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm
77	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper
78	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm
79	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced withgalvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware,SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleevefor fixing frame to finished wall as perIS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paidseparately. Note:- Structural design proof checked from a Government Engineering Institute,to be provided by the manufacturer for : (i) Siteswith basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii)Sites with structure height more than 20m for all wind speeds
80	Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x(55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height upto 1.8m).
81	Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m)
82	Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges,multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.Using R3 series with frame (55 mm & above) x (50mm & above) & sash (55 mm & above) x (85mm & above) & French (False) mullion (55 mm & above) x (60mm & above). (Height upto 2.5 metre).
83	Fixed window / ventilator without mullion / transom. Using R1 series with frame (33mm & above ) x (35mm& above). (Height upto 0.90 metre)
84	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):(Cost of aluminium snap beading shall be paid in basic item):
85	With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
86	With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)
87	Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture withmatching wood beading
88	Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopperetc.to be paid separately).
89	Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Prelaminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 25 mm thick.
90	Providing and laying integral cement base water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm ofcement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab adjoining wall upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken brick bats 25mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining heights upto 300mm height including rounding of junctions of walls and slabs. (c) After two days of propoer curing applying a second of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed water proofing compound conforming to IS 2645 and approved by Engineer in charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300 x 300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test . All above operations to be done in order and as directed and specified by the Engineer-in-charge with average thickness of 120 mm and minimum thickness at khurra as 86mm
91	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
92	Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.
93	For vertical surface two coats @ 0.70 kg per sqm per coat
94	For horizontal surface one coat @1.10 kg per sqm.
95	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase
96	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet complete.
97	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter
98	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
99	12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
100	Providing & fixing false ceiling at all heights withGRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laidin true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising ofmain-Trunners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm andsecondary intermediate cross-Tof size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm)i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.
101	With semi perforated12 mm thick micro tegular edged GRG false ceiling tiles.
102	Provinding and flixing toilet cubicle systems with 12 mm thic solid Cubicle Board BSL. Action Tesa Boilo (HDF High Density Fiber Board), Allpilastersaretobesupportedbyadjustablefootandnoncorrosiveinserts.Toprail andwallfixingwithandexterior polyamidecoatingguaranteesresistanceto breakage,heat,humidityandchemicals.Thebaseoftheadjustablefootwill be anchoredtothefloorwithaclearanceheightof150mm.AluminumU-Channelwill beusedforthefixingofintermediatepanelstothewall.Thetoiletcubiclesetupshallbe:SmartSeries1.Cubicles (1.00-1.20 W, 1.50m L & 2.0m Height)-W- as persiteXD-as per siteXH-2000mm; DoorsizewillbeW-600mmXH-1800mm2.UMP\"s-W-450mmXH-900 mmalll SS Fittings complete as per site-in-charge.
103	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid Make: Jaquar (FLS-WHT-5353PPZ Rimless Bowl with Cistern For ExtendedWall Hung WC with PP Soft Close Seat cover, Hinges, Dual Flush Cistern Fitting, Accessories Set, Size: 380x650x730 mm)
104	Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
105	Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
106	Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
107	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P.brass pillar tap
108	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia
109	Providing and fixing 100 mm sand cast Iron grating for gully trap.
110	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
111	100 mm nominal dia Pipes
112	150 mm nominal dia Pipes
113	Providing and fixing PVC pipe conforming to IS make working pressure 6kg/sqcm including testing labour T&P and all complete fittings
114	150mm dia
115	100mm dia
116	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
117	20 mm dia (iner fitting)
118	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall
119	32mm dia (outer fitting)
120	Providing and fixing gun metal gate valve with C.I. wheel of approved quality {screwed end):. 32mm dia
121	32mm dia
122	Providing and fixing SS Materials bib cock of approved quality conforming to IS standards 15 mm nominal bore QQP-7037PMBib Cock with Wall Flang Jeaquar Make:- Jaquar
123	Providing and fixing SS Materialsbib cock of approved quality : 15 mm nominal bore FLP-5037PM Bib Cock with Wall Flange Make:- Jaquar
124	Providing and fixing SS Materials stop cock of approved quality : 15 mm nominal bore FLP-5083KPMExposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever &Adjustable Wall Flange with Seal (compatible withALD-083, ALD-089 & ALD-081) Make Jaquare
125	Providing and fixing SS Materials FLP-5281PM Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange (without Hand & Overhead Shower) Make : Jaquare
126	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter
127	Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
128	Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
129	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
130	Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
131	Providing and fixing 600x450 mm beveled edge mirror of superior glass (ofapproved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
132	Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 15 mm nominal bore
133	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x460 mm bowl depth 200 mm
134	Providing and fixing C.P. brass angle valve for Basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore
135	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :
136	Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
137	Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern
138	Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
139	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
140	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
141	15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)
142	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
143	Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
144	Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge
145	Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30
146	Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge.
147	Extra for providing and mixing hardening compound of approved quality as per manufacturer\"s specification in cement concrete.
148	Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, j ointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making j oints with or without grooves (thickness of j oints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
149	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge. 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.
150	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment)
151	Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment).
152	Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge
153	Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge. Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing group)
154	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
155	Trees Plant
156	Shrubs Plant
157	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : HOLES 45CM DEEP, 45 CM DIA
158	Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-165 cm. with 8-10 branches and healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.
159	Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 34 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.
160	Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.
161	Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.
162	Providing and stacking of Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.
163	Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge.
164	Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.
165	Providing and stacking of Tecoma stans of height 45-60 cm. branched in earthen pots of size 20 cm as per direction of the officer-in-charge.
166	Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.
167	Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.
168	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep
169	Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.
170	Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
171	Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
172	Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v
173	Providing and stacking of Ficus infectoria (Pilkhan) of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.
174	12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)
175	Supplying and laying of following size Water Line (DWC SN-4 Cass pipewith Integral socket confirming to IS 16098, Size As Per DWG.) marked along with all accessories like socket, bend, couplers etc.complete with fitting and cutting, jointing etc. in the existing trench, complete as required.
176	150mm dia Pipe
177	200mm dia Pipe
178	Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layersnot exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
179	Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:
180	100 mm dia Ductile Iron Class K-9 pipes
181	150 mm dia Ductile Iron Class K-9 pipes
182	Providing flanged joints to double flanged C.I./ D.I. pipes and specials, including testing of joints :
183	100 mm diameter pipe@ 5.0mc/c
184	150 mm diameter pipe@ 5.0mc/c
185	Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class) Up to 300 mm dia
186	Providing and laying S&S C.I. Standard specials suitable for mechanical jointing as per IS : 13382 Up to 300 mm dia
187	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
188	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testingof joints complete as per direction of Engineer in Charge. External work
189	25mm nominal outer dia pipes
190	50mm nominal inner dia pipes
191	40mm nominal inner dia pipes
192	Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :
193	20mm nominal bore
194	25mm nominal bore
195	Providing and fixing gun metal gate valve with C.I. wheel of approved quality {screwed end):
196	25mm nomiinal bore
197	32mm nomiinal bore
198	50mm nomiinal bore
199	40mm nomiinal bore
200	Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :
201	50 mm dia
202	80 mm dia
203	Provideing and fixing C.I. Sluice Valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separtely):
204	100mm diameter
205	Class II
206	150mm diameter
207	Class II
208	Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
209	Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming to IS : 4885
210	Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m With Sewer bricks conforming IS : 4885
211	Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885
212	Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : With Sewer bricks conforming IS : 4885
213	Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
214	Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/ spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes.
215	SUB HEAD : RAIN WATER HARVESTING WORK
216	Supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete.
217	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
218	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia
219	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia
220	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
221	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
222	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
223	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
224	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia
225	Supplying, Installation, testing & Commissioning of STP/ETP of appropriate technology including civil work (except plant room), tertiary teratment etc. for the building /campus
226	Plant Size upto 50KLD
227	Add extra for every KLD for plant size above 50 KLD and upto 100KLD
228	Supply and buring of Safe earthing electrode T- 19 (Hot Dip Galvanzid), Lengthup to 3000 mm, outer dia 50 mm inner Dia 25mm. , terminal Dia 12 mm, outer GI pipe of 16 swg. And inner GI pipe of 12 swg with Hot Dip Galvanzization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducingthe soil resistivity with good mixture of retaining capacity and one earthing lead of 25 mm x 3 mm G.I. strip, upto switch board (from apron to switch board, the cost of G.I. Strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housingSI. no. 725(B) SOR 2018
229	Supply and Fixing of 16 Sqmm 4 core \"AL\" conductor PVC insulated and and serve sheathed round cable 1000 Volt grade at depth of 750 mm below ground level over and cushion of 75mm thick sand all round and protected…………….etc complete. SI. 501 (I) Sor 2014
230	Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge. 16 sq. mm
231	S&Fof 320 A. 415 VHeavy Duty Double Break HRC fusetype metal clad TPN complete with HRC fuse etc. on angle ironframe complete in all respect.
232	Transportation ofdrilling equioment and other accessories to site of work all complete.
233	Drilling tube well by R.C. /method/ Rotory rig 400-500 mm. dia hole all complete as directed by E/I
234	Supply owering & Fixing of M.S. blind or slotted pipe along depth as per requirement of site including cuitting the pipe welding of pipe socket etc.including supply of all material abour T&P etc. all complete.
235	200 mm. dia housing pipe (blind) plain. (5.3 mm thickness).
236	200mm. Dia slotted pipe plain (5.3 mm thickness).
237	Supply & pouring of pea gravel 1.6 mm size surrounding bore well after washing & sceaning as per direction by E/I.
238	S/F of 200 mm dia approved quality bail plugh etc.
239	S/F of 200 mm dia approved quality well cap etc.
240	S/F of 200 mm. dia pipe socket of approved quality.
241	Development by air Comprassior of tube well including labour, T&P etc. all complete.
242	Development by Generator deiven O.P. unit of tube well including labour T&P etc. all complete
243	Transportation of devlopment equipment and O.P. Unit D.G. set all complete.
244	Collection & Sampling of stratar cutting …….etc all complete.
245	Water arrangement charge for drilling the tube well all complete.
246	Supply and Fixing of 80mmx80mmx80mm dia G.I. Tee including labour T&Petc. All complete.
247	Supply and lawring of 12.5 HP 7 stage,61 mtr head (discharge 710 LPM), 3 phase 440 volt A.C.operated motar pump set ISI Marked complete with all taxes etc. as per direction of E/I. make varuna KSB& Crompton with all taxes etc. as per direction of E/I.
248	S/F of M.S. clamp 80mm. Dia with 80x10mm. Plate iron to hold pump set into tube well with Nut bolt etc. all complete.
249	S/Laying of 2 No. (3 core 6 mm 2)size flat submersible cable with connection complete in all respect. (Finolex make)
250	Supply and lawring of 80mm dia ( 3\") UPVC column pipe ISI marked (each pipe having 3 mtr. Length) heavy duty red screen self pulling load capacity 6000 Kg, Self allowheel hydrostatispressure 25 KGF/per Sqcm. Including inbilled standerd socket and rubber oaring including all taxes as per direction of E/I.
251	S/F of control pannel board suitable for 12.5 - 15 HP 3 Phase submersible pump motor set including 1 No. 0-500V volt meter 1 No. 0-30 Amp. Ammeter AE make, 3 no. 63 AMP. Fuse unit 3 no. indicator lamp & one number oil field star delta motor, starer make Bentex. etc complete
252	Supply fixing and testing of C.I. double flange bend suitable for 80 mm dia M.S. pipe. All Complete with nut bolt, rubber packing piece etc all.
253	Supply fixing and testing of C.I. Sluice valve of 80mm.dia approved quality with nut rubber packing piece etc. all.
254	S/F of reflex valve 80/100 mm dia size
255	Water logging testing of bore well for Water quality in starta all complete.
256	Supply of 2 tonne capicity 4.5mtrlift M type spour geared cjainpully block
257	Supply and laying of 32 mm x 6 mm G.I. strip from earth electrode directly in the ground as required complete in all respect
258	Providing and Fixing of Stretch HUSH wall fabric system, By using Hush Fabric of size 1400mm width, shall be stretched by using wooden base 10mm thick and rigid vinyl Stretch Tracks full wrap 15mm (FS15) and Midseam 15mm (FS15), strand board, synth PF infill with requisite accessories & tools strand square edge magnesite bonded finewood fibre panels of size 600 x 1200 x 15 mm having density 400 Kg per cum and weight 4 Kg or more is fixed to existing frame work in between vinyl tracks with suitable fasteners Synth PF 10 x 10 mm thick shall be pasted on strands panels using suitable adhesive. Installation- Wooden base 10mm is installed along the marking lines with metal fasteners inserted at 300mm centers. FS15 fullwrap tracks to be installed on wooden base, at free edges,after applying adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Track outer corner should be installed on woodenbase at corners of column projection.Fabric of width 700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm. The fixing need to be approved from Engineer in charge as per approved design of panels & requirement at site. Nothing extra shall be paid and only finished panelling area shall be measured for payment.
259	Providing and Fixing of ‘Wooden Slats’ 2430x131 mm with thickness of 16 mm MDF backed with acoustical Fleece providing sound absorption of NRC 0.70 tested as per IS:8225- 1987.To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is 750-800 kg/m3.The panels come with tongue & groove for seamless patterns, 2-14mm Groove and visible panel.Wooden slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes should be available on the back of panel which are covered by black acoustical fleece.INSTALLATION: ‘Wooden Slats’ can be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick,1000 GSM Acoustic Wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results.
260	Providing and Fixing of acoustical false ceiling with perforated Gypsum board(India Gysum) of minimum 10mm tickness with given design and cove for making parterns, cement fiber elgant with accoustic value NRC 0.7.
261	Providing & fixing at all height Stage false ceiling of 20 mm thick Mat Black wood wool sheet(Echomute) panels of size1200 x 600 mm laid over MS Suspension Grid consisting of 2 nos 40 X 40X 5mm MS Angles(Capital or eq.) (GRID will be taken extra in another item) welded back to back @1200mm c/c & M.S. Tees @ 600mm c/c .
262	Providing and Fixing of gypsum cealing and thickness of 20 mm are made with inorganic binder wood fibre, which in all contribute to its wondering features & provide NRC 0.85 tested as per IS:8225-1987 (Equivalent to ISO: 354- 1985 & ASTM 423-90). Panels are an ecological green material. It is non flammable as per IS:3614 (Part-II). It facilitate fast, rapid construction of walls & roofs.Panels can be installed with Coloured Aluminium H Profile on G.I studs 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick Acoustic Wool tested as per Fire Reatrdant ASTMD 635-1991 and IS 15061-2002 for excellent results.
263	Providing and fixing 100% Polypropelene Stainsafe carpet having following characteristics : Pattern Loop Graphic, Primary Backing : Woven PP Secondary backing : Dimenstionally stable woven Action back Pile eight/thickness : 6mm(+/-5%), Pile weight : 850gm/sqm (tolerance -5%) or more Light fastness : >5 Water esistance 4-5 Fire Class : Efl (EN13501-1) Characteristic : Bleech resistant Width : not less than 3.5m The carpet shall be of make Milliken / Interface / Unitex / Divine / Checkmate or quivalent. Carpet to be installed over with 8mm thick PU foam over CC / kota flooring, fixed with approved synthetic adhesive SR-505 (Qty minimum one litre per 3 sqm for both foam& carpet) or as recommended by anufacturer of carpet, the colour and pattern of carpet as approved by engineer-in-charge all complete (Note : The cost of 6 mm thicknes PU foam, adhesive & other incidal items included this item)
264	Providing and fixing of Auditorium Chair in position, Heavy Duty ergonomically designed auditorium chairs which have gravity type, spring free TIP-up (without any stop or time lag) and rocking back with central Pedestal. The chairs shall be fully upholstered having Wooden Laminated Back on back side. The Chair shall be fixed as per approved layout, which is to be submitted by the contractor based on actual dimensions of Auditorium steps measured at site and approved by the Engineer in Charge. The Chairs shall be of sufficient width having placement 570-590 mm centre to centre and height of back should be 1020 (+/- 20) mm.
265	DOOR FRAME: Wooden Door Frame of section 145mm x 75mm or 95mm with heat activated intumescent fire seal strip of size 10mm x 4mm Twino Type Astroflame U. K.) and acoustic seal Raven RP24. DOOR SHUTTER: 77mm thick having 38 dB acoustic cum fire door of 60 / 120 min. fire rating having infill of 47mm thick 3resin bonded glasswool of 24 Kg /M density coated with FR acrylic, including Panic Bar, door closure, stopper and all other accessories required by department.
266	PROSCENIUM: P/F of M S structure ( Capital or eq.) fixing of 12mm ply(Green or Eq.) & final finish with laminate
267	Supply Installation testing and commissioning Stage Flooring 65x15. 2nd class Teak wood planks flooring with Tongue and Groove joints of 22mm thick (concealed screwing) over 50x50mm section Sal wood framing @ 600mm c/c in both directions with 12mm thick commercial ply(Green or eq.).The framing to be filled with 50mm th. fibre glass resin bonded insulation of density 24kg/cum.
268	SITC of Main Curtain made out of Crape curtain cloth with horizontalslidingarrangementcompletewithfixingrails,brackets, slidingarrangement&motorisedoperationcompletewithrunners, master runners, pullies, 3mm steel wire rope, 1 HP motor (Crompton) 2nos.air breaker contactors (L&T/SIEMENS) ,2nos. micro switches forautostop,3nospushbuttonsforforward,reverseandstop positions.The curtain should be draped to half area when in closed position. Minimumoverlapatcentreshouldbe900mmandshould be stitched in double gathering can be operated manually or through remote .
269	SITC of Rear Curtain made out of glazedcotton curtain cloth with horizontalslidingarrangementcompletewithfixingrails,brackets, slidingarrangements&motorisedoperationcompletewithrunners, master runners, pullies, 3mm steel wire rope, 1HP motor (Crompton) 2nos. air breaker contactors (L&T/SIEMENS), 2 nos. micro switches forautostop,3nos.pushbuttonsforforward,reverseandstop positions.The curtain should be draped to half area when in closed position. Minimumoverlapatcentreshouldbe900mmandshould be stitched in double gathering, can be operated manually or through remote .
270	SITC of valance/Frill made out of Crape cloth to be installed above the stage on 25mm dia GI pipe with the 300% gathering of Size. The work shall be executed as per drawings, specifications&instructionsofengineerinchargeinall respect to approved makes.
271	SITC of of WINGSatStagewith Crapebluefabric(weightnotlessthan290gms/sqm fixedcomplete on 50x 25(1.6 mm thick) MS tube framework@ 1200 (V) x600 (H) c/c backed with 6mm ply & 12mm U foam below the fabric. The wing to be mounted with central pivot mechanism for180 degree rotational movementat top & bottom.Size 1.2 mtr (w) x 7.5 mtr (h) approx. The work shall be executed as per drawings, specifications&instructionsofengineerinchargeinall respect to approved makes.
272	Providing and Fixing of Stage Lighting Bar, 50mm dia B class GI Pipe of suitable size fitted with 15 amp. sockets suitable for stage light installation.
273	SITC of Grid frame work with MS pipes of 50x50mm of 14gage with black finish paint for supporting wings and light structure. The work shall be executed as per drawings, specifications&instructionsofengineerinchargeinall respect to approved makes SAIL, TATA, Jindal, APL, Apollo.
274	SITC of Front of House Winch Suspension Systems: Motorized bars winch operated suspension sets min 500 kg capacity, 4 lines block winch unit with handle and ratchet, clew plate and steel wire rope for lifting, etc for lighting bars, scenery sets and front masking frills. The work shall be executed complete as per specifications, directions of the Engineer-in-charge. Make : TDH, Model : Custom Item
275	Providing and Fixing of Side Ladder, 50mm dia B class GI Pipe of suitable size fitted with 15 amp. sockets suitable for stage light installation.
276	SITC OF Two-Way Full Range Loudspeaker with 2 x 10\" Differential Drive,Frequency Range (-10dB) 86 Hz - 18 kHz,Frequency Response (±3 dB) 109 Hz – 15.3 kHz, Full Range 800 W Continuous Pink Noise (3200 W peak), 2 hrs 400 W Continuous Pink Noise (1600W peak), 100 hrs, Bi-amp LF 800 W Continuous Pink Noise (3200 W peak), 2 hrs 400 W Continuous Pink Noise (1600W peak), 100 hrs Bi-amp HF 150 W Continuous Pink Noise (600 W peak), 2 hrs 50 W Continuous Pink Noise (200 W peak), 100 hrs Full-Range 80 V Rms (2 hrs), 160 V peak Maximum SPL (1m) 131 dB Cont. Ave (2 hrs), 137 dB Peak Coverage Pattern (-6 dB) Horizontal: 100°.
277	SITC of Dual 15\" Subwoofer with Differential Drive, Frequency Range (-10dB) 52 Hz – 210 Hz, Frequency Response (±3 dB) 62 Hz – 123 Hz, System Power Rating 1600 W Continuous Pink Noise (6400 W peak), 2 hrs800 W Continuous Pink Noise (3200W peak), 100 hrs, Maximum Input Voltage 80 V Rms (2 hrs), 160 V peak, Maximum SPL (1m) 127 dB Cont. Ave (2 hrs), 133 dB Peak, Sensitivity 98 dB (52 Hz – 210 Hz, 2.83V), Impedance 4Ω, 3.0Ω min @ 195 Hz.
278	SITC of OEM frame for given speakers and subwoofer for taking relevant load with motorised lift up and down array from flloor.
279	SITC of 15\" Loudspeaker for Balcony and underbalcony line arrayable Transducers Low Frequency : 15\" Cone transducer & High Frequency 1.75\" , Frequency Range (-10 dB) : 44 Hz - 20 kHz, nominal Coverage(-6dB) :90° H x 80° V, Amplifier Power Output : 500W Maximum SPL (@ 1 m) 131dB SPL ,Configuration : 2-way Line array element.
280	Rigging Hardware/ Bracket: Aluminum array frame for same Series enclosures;
281	SITC of Active Stage Monitors Transducers :Low Frequency : 12\" Cone transducer & High Frequency 1.4 \", Frequency Range (-10 dB) : 45 Hz - 20 kHz, Nominal Coverage Angle :75° Axisymetric, Amplifier Power Output : Class D 1500W, Maximum SPL (@ 1 m) 130dB SPL, Configuration : Multi-purpose, 2-way powered loudspeaker
282	SITC of Front fills Transducers :Low Frequency : 8\" Cone transducer & High Frequency 1.4 \", Frequency Range (-10 dB) : 45 Hz - 20 kHz, Nominal Coverage Angle :75° Axisymetric, Maximum SPL (@ 1 m) 110dB SPL, Configuration : Multi-purpose, 2-way powered loudspeaker
283	SITC of Control Room & Green Room : Transducers Low Frequency : 6.5\" Cone transducer & High Frequency 1 \" , Frequency range (-10 dB) : 70 Hz - 20 kHz, Nominal Coverage Angle :120° Axisymetric Power handling : 40W or more Transfomer tap settings at 100V: 40, 20, 10 W and 150W RMS at 8Ω bypass Maximum SPL (@ 1 m) 110dB SPL, with respective volume control at each room
284	SITC of Two-channel, 2400W @ 4Ω Power Amplifier, 2400W at 4ohm at each channel, Frequency Response (8Ω, 20Hz - 20kHz) ±0.25dB, Total Harmonic Distortion (at full rated power, 20Hz - 20kHz) 0.35% Damping Factor (20Hz to 100Hz) >5000, Load Impedance (Stereo/Dual Mode) 2Ω - 16Ω; 70Vrms and 100Vrms, Load Impedance Bridge Mono 4Ω - 16Ω; 140Vrms and 200Vrms, Cooling Continuously variable speed forced air, front to back airflow Required AC Mains (±10%) 100V-240V ~ 50/60Hz.
285	SITC of dual channel class D amplifier with 1350W RMS output power at 8Ohm. Frequency Response (4Ω and 8Ω) :20 Hz - 20 KHz +/- 0.1 dB, Signal to Noise (20 Hz - 20 KHz) >100 dB
286	SITC if Multizone Class D amplifier : Number of channels: 1 or more Power output per channel(@8ohm,4ohm) : 500W per channel or more Frequency Response (4Ω and 8Ω) :20 Hz - 20 KHz +/- 0.1 dB, Signal to Noise (20 Hz - 20 KHz) >100 dB, minium 4 zone out to control individual speaker with built in mic and line input.
287	SITC of Analog Mixing Console, 232 Line Inputs (24 mono and 4 stereo), 4 GROUP Buses + ST Bus with 6 AUX Sends + 2 FX Sends, 1 Matrix out, FX1:REV-X(8 PROGRAM, PARAMETER control)/ FX2:SPX(16 PROGRAM, PARAMETER control), MIC: 24 (INPUTS HPF: 100Hz 12dB/oct), 48V phantom power per channel, LINE: 24 mono + 4 stereo, CH INSERT: 24 RETURN: 1 stereo, USB Device, iPod / iPhone, TDH 0.02% (20Hz-20kHz@ +14dBu),Frequency Response +0.5/-1.0dB 20Hz - 20kHz, refer to the nominal output level @1kHz.
288	SITC of Complete Loudspeaker Management System: Input Processing - Compression, AFS™ (Advanced Feedback Suppression), 31-Band Graphic EQ, 12-Band Parametric EQ (with narrow notch capabilities), Subharmonic Synthesis, Backline Delay, Noise Gate, Output Processing : Crossover (supports full range up to mono 6-way systems), 12-Band AutoEQs (8 AutoEQ bands, 4 User bands), Automatic Gain Control, Subharmonic Synthesis, Noise Gate, Tower Delays (up to 1000ms per output), 8-Band Parametric EQs (used for speaker tunings).
289	SITC ofDynamic Super Cardioid Wired Handheld Microphone for speech and vocal,Extended high frequency range,Handles high sound pressure levels,Frequency response (Microphone) 40 - 16000 Hz, Nominal impedance 350 Ω,Sensitivity in free field, no load (1kHz)1,8 mV/Pa.
290	SITC of Dynamic Wired Handheld Microphone with ON/OFF Switch, Rugged metal body,Excellent feedback and spillage rejection, Good suppression of handling noise, Nominal impedance 350 Ohm,Sensitivity in free field, no load (1kHz) 1,5 mV/Pa,Min. terminating impedance 1000 Ohm.
291	SITC of Dual Hand Wireless Microphone with Lithium batteries and recharging cable, True diversity receiver with metal housing ,External antennas. Automatic frequency management and synchronization via ,remote channel for easy setup Fully tunable over a wide range of UHF frequencies ,Up to 12 compatible channels,Power supply 12 V DC nom. / 300 mA ,AF frequency response 50 to 16,000 Hz (–3 dB)
292	SITC of Dual Lapel Wireless Microphone with Lithium batteries and recharging cable, True diversity receiver with metal housing ,External antennas. Automatic frequency management and synchronization via ,remote channel for easy setup Fully tunable over a wide range of UHF frequencies ,Up to 12 compatible channels,Power supply 12 V DC nom. / 300 mA ,AF frequency response 50 to 16,000 Hz (–3 dB)
293	SITC of wired Gooseneck Microphone:AF frequency response 20 to 20,000Hz, Dynamic range > 120dB(A),Signal-to-noise ratio > 90dB(A).
294	Supply and laying of 8 core shielded microphone snake cable for mic points and powered speakers
295	Supply and laying of 2 core 2.5sqmm speaker cable for speakers connectivity.
296	Supply and laying of 2 core shielded microphone cable for mic leads and other signal connectivity
297	SITC of stage box with multi mic inputs and power points.
298	Supply of Microphone Stand 4 small and 4 big Floor/Table Tripod type
299	SITC of Cable Tray Arrangement (40 X 150 X 40 MM) with pouder coating.
300	SITC of 25mm PVC conduting with all joint and bends for cabling laying
301	SITC of all XLR male, female, Speakon, Chassi mount and other necessory connector for final commissioing
302	Supply and Fixing of Equipment rack 36 U with power strip, fan, doors, wheels, drawer for accessoories with lockable facility.
303	STAGE LIGHTING (B) SITC of 54x3W LED par light complete with 8- channel DMX 512, high brightness mixing color evenly, stable performance with sound active auto, DMX, and power and DMX loop in and out option, undergone through 7 Tank chemical treatment to keep them rust free and, duly powder coated in black matt texture finish and technical specifications as below. Lamp -
304	SITC of 200W LED Profile light 19 degree with below specifications :- Lamp Power : LED, 200W Power Supply : AC 110-230V, 50Hz Focus : Manual Focus , Beam Angle : 19° , Dimmer : 0-100% linearly adjustable manually focusable, high quality optical system, glass reflector. DMX Control protocol: DMX 512. , CRI : >90 , Dimming :
305	SITC of Planoconvex Lights :-400W LED PC Light . 400W LED PC Light 30 Degree complete with 3200K/5600K CCT 4x100W Chip On Board LED lamp source, DMX 512 dimming with 4/8 Channel modes, Black finish housing, IP20 protection having Strobe option and smooth dimming, illuminate Stage with uniform light intensity levels
306	SITC of 200W LED PARCAN with below specification : Lamp power - 200W , LED Type : COB LED, Color Temperature 3200K Power Rating - IP 20 , Control Manual , DMX, Channels - 2 channel DMX 512 , Power Supply - 100-240 V AC, 50/60nHz
307	SITC of 200W LED Fresnel Cyclorama Light with 200mm dia German Lens with below specification : Lamp power - 200W , LED Type : COB LED, Color Temperature 3200K ,CRI > 95, spot - Flood Focus adjustment : Mototrised, Beam angle - 10° 50°Power Rating - IP 20 , Control Manual , DMX0-100% through manual and DMX , Channels - 2 channel DMX 512 , Power Supply - 100-240 V AC, 50/60Hz
308	Supply of Moving Head/ SHARPY LIGHT 15R, Voltage: 110V~240V/50-60Hz, Ballast: Electronic ballast, Lamp: YODN 280W R10, Color temperature: 8500K, Life Span: 2000H, Colour Wheel: 14 Color + Blank Color Whee
309	SITC of 200W Warm White with below specification : Lamp power - 200W , LED Type : COB LED, Color Temperature 3200K Power Rating - IP 20 , Control Manual , DMX, Channels - 2 channel DMX 512 , Power Supply - 100-240 V AC, 50/60nHz complete etc. as reqd.
310	SITC of Light fixture mouting clamp Customized for suspending on fixed bars on stage Made up of Aluminium or MS material Complete with black powder coating matt black finish.
311	SITC of V3 Controller - Total 2048 DMX Channel offer4 Individual optical isolated DMX interfaces and 1 Art-Net interface . One high resolution 15 inches capacitive LCD Touch screen. 15 playback faders and 15 playback keys run with 80 pages. 4 backit optical encoders for data settings . The key backit offers three color options and adjustable brightness, playback faders with backit which can be set to different colors for 3 different states.Individual keys for the flash and pause function for playback , provide midi in , out and thru interface to connect and work with other devices. Accept midi time code signal. WiFi antenna provides WiFi signal for connecting App on mobile or tablet. USB 2.0 interface allows you to backup shows on the external disk. Offer one 3.5mm stereo audio interface one audio optical interface and a headphone interface. I Working lamp interface with luminance interface .1 working lamp interface with lumination regulator. Power supply -AC100-240V, 50 -60HZ.
312	SITC of Opto isolated RDM enabled DmX splitter unit provided with 8 Isolated outputs Slow blow safety fuse 5 Pin XLR for output interface Dual mode to select 2 universe operation DmX Input through 5 Pin XLR Connector Powder coated compartment finish Mounting brackets for grid mount
313	SITC Lights point :- Light Point Wiring from Patch Panel to be Light Point Wiring from Patch Panel to bewith 1.5 Sq.mm 3 Core PVC Insulated and PVCSheathed Cable including of suitable size forlaying these wires including 16 amps metallic industrial cladsockets with box at top and FRLS cable
314	SITC DMX POINT:- interconection of signal cable with XLR conector
315	SITC DMX Cable :- 2 core shielded DMX Cable for light
316	SITC of Cove Light with Havells LED strip inside on DC Power 5mV, Along with transculant covered
317	Special Application of LED Step Light for Multiplex Cinema Theatre\"s, Auditorium etc. with a Lamp a life of more Than 2 year amd consume less than 5W. Black anodized profile with anti-slip polymer rubber and riser illumination LED (12/24V DC) available color in blue, white, green, red or yellow. Minimum Length 1.45mtr for Step. With labeling on every alternate row.Quotation Rate
318	SITC of LED DISPLAY : 2.5 mm Pixel Pitch based Indoor Direct View True Color LED Wall Screen Size 36 x 20 feet, Configuration : SMD 3-in-1 LED Type Alluminium Die Cast, Pixel Density : 1,60,000 pixels/m2 or better, Brightness Calibrated : 500 cd/m2 or better, Dimming Capability : 0-255 Levels or higher, Contrast Ratio : 3000:1 or better, Refresh Rate : 1920 Hz or better, Color Processing : 14-bit or better, Colors : 4.4 Trillion or better, Half Gain Viewing Angle : H: ± 80° or better, V: ± 80° or better, Lifetime : 100,000 hrs or better, Indoor P 2.5 , LED Video wall Solution, Modules,Receiving Card, Power Supply, Cable and Connectors etc. Brightness : 500 Nits, Life - 100000 Hours, Module Based Installation, Screen Diagonal In Inch 217LED Wall Resolution 1920 x 1088 With Control System : 4 Inputs Control Systems Module IP 65 with 4 K controller , Resolution support up to 20.8 Million pixels, HDR , HDCP ,3D , EDID support, Seamless switching & scaling, fade in/ fade out, PIP function support size & location, Low latency, Support colour ,Brightness, Contrast, saturation, Grey scale adjustment, Option of Live video on HDMI , Scheduled playback and preset, Support 4:4:4,4:2:2, 4:2:0( RGB/YCbCr), Hot swappable Input/outputs .Signal Input : DVI/ HDMI , Signal Output : RJ45, Input Voltage : 100~240 VAC, Processor : Intel/ARM /Other High End, OS : Android/windows, Internal drive : 8 GB , Video : At least should support MPEG-4,MOV, Audio : MP3,WAV,AAC, with PDU, Wall Mount MS Structure for Video wall.
319	Supply & Fixing of 8x8 Input presentation switcher/scaler with HDbaseT & HDMI simultaenous ouputs with 4 HDMI and 2 computergraphicsVGAinputwithmicrophoneinputand audio embedding and De-embedding with audio equalization.Mixingwithautoinputswitching,supporting resolution up to UXGA/1080P having control over ethernet &builtinwebpages,RS-232andcontactcolsuresfor further controlling in respect of approved makes.
320	Supply, Installation, Testing & Commissioning of HDMI & Control twisted pair/Hdbase T receiver, 4Kresolution support,Input:1xRJ45,Output:1xHDMI,1xControls (RS232/IR) distance support of 70mtrs or more for reception of audio, video, control & power with feature of De- embedded audio. Should be compatible to the multi-format transmitter orScaling Matrix Switcher in respect of approved makes.
321	SITC of Digital Podium :with inbuilt 19\" interactive panel with motorized tilting of panel, top connection panel with connectivities such as power for external laptop, VGA input, vga swicther for toggling between visualizer, cpu and external laptop, usb ports for connecting external pen drive directly to the cpu, with builtin I3 -CPU.
322	SITC of WirelessPresentation System: Wireless connection to central screen, Up to 2 users on-screen, Share from laptop, tablet or smartphone, Enhanced security features, Touch back support, Central management, Delivered with 2 Buttons,Operating system Windows 7/8/8.1/10 32 & 64 bit,Video outputs 1x HDMI 1.2, Output resolution 1920x1080 @60Hz, Audio Via HDMI, analog via Audio Jack 3.5mm, S/PDIF, AirPlay Support iOS 11, 12 & 13 / macOS 10.14, 10.15, Google Cast Support Android 9, 10, Frame rate Up to 30fps*, Number of simultaneous connections 16, iPad, iPhone and Android compatibility Sharing of documents, browser, camera for both Android and iOS devices via ClickShare app or using AirPlay / Google Cast.
323	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. Make : D-Link, Model : Cat-6
324	SITC of Accessories: HDMI cable, Ceiling Mount Kit, Power and patch cord. cable and other necessory cables Custom
325	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
326	Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /ecessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
327	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
328	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
329	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
330	2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
331	4 X 10 sq. mm + 2 X 6 sq. mm earth wire
332	4 X 16 sq. mm + 2 X 6 sq. mm earth wire
333	Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
334	2 Pair
335	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
336	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
337	25 mm
338	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
339	Telephone socket outlet
340	TV socket outlet
341	RJ45 socket cat 6 with shutter
342	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
343	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
344	1 or 2 Module (75mmX75mm)
345	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
346	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
347	Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.
348	Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
349	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
350	1 run of cable
351	Wiring for group controlled (looped) light point/fanpoint/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
352	Group C
353	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
354	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \"C\" curve including connections, painting etc. as required.
355	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
356	4 way (4 + 12), Double door
357	6 way (4 + 18), Double door
358	8 way (4 + 24), Double door
359	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
360	Single pole
361	Double pole
362	Three Phase & Neutral
363	Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
364	25Amp.
365	63Amp.
366	Supplying and fixing 40/63A rating, 415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.
367	Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.
368	100 mm width X 50 mm depth X 1.6 mm thickness
369	300 mm width X 50 mm depth X 1.6 mm thickness
370	600 mm width X 50 mm depth X 1.6 mm thickness
371	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
372	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
373	Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
374	Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
375	Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
376	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
377	Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
378	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
379	LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required
380	with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).
381	Powder coated die cast / Extruded aluminum Body including trim.
382	8 - 10 watt
383	12 - 15 watt
384	SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduitounting (with accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU GR or equivalent.
385	Supply and fixing ofwater tight oblong 10 Watt LED bulkhead luminaire having pressure diecast housing with driver set confirming to IP 65 and above Protection, IK08, High purity / transmisivity UV stablized Non yellowish diffuser/ Reflector for uniform light distribution, ditachable driver set, suitable for 24hrs continuous operation complete in all respect. 1200 system lumen, >120lm/W, PF>0.95, CRI>70,>300V, over voltage protection, 4KV internal surge protection with 5 year warrenty. CAT-AAA
386	LED Batten light (System lumen efficacy >135 lm/Watt)Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/ 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Testeport from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineerin-Charge as per requirement. (Thermal management: heat sink ofaluminum housing such that LED junction temperature shall not rise above 90°C).
387	Powder coated die cast /Extruded aluminum Body (Thickness ≥ 1.20mm)
388	18- 22 watt
389	LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).
390	36W
391	RecessedPIR Motion Sensor Similar to Wipro Make : GLPS01R010HA or equivalent
392	Supply of backlit, 33W SMD LED 2x2 luminaire suitable for Armstrong / CRG /TRAC / USG/Celotex modular ceiling system having luminous efficacy of(3300lm) with dimension of 595mm x 595mm and height of 48mm. The luminaire should be able to be mounted on POP/Gypsum ceiling with the help of additional frame. Luminaire shall be made up of white powder coated extruded Aluminium housing with C shaped opal diffuser. The lumianire should supplied with inbuilt heat sink to provide better thermal management to enhance LED life. Luminaire should comply to LG7 guidelines. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. The luminaire should be IP20 ratedandDali Dimmable The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Integrated type, Isolated, Constant Current operated driver with range 150-270V AC.DaliDimmable Driver Efficiency > 85% & 3 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012.Similar to Wipro Make: LM29-451-XXX-57-XX or equivalent
393	Brush Less Direct Current (BLDC) MotorSupply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)
394	Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0 mm thickISI Marked G.P.sheet spot welded Four to Eightholes for pipe entryof the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C. roof before concretingalongwith supply of all material, labour, T&P etc. required for proper completion of the work.
395	Lightning Arrestor: Supply, installation, testing and commissioning of External Lightning wide area protection system based on Eaarly Streamer Emission (ESE) technology. Device shall emit electromagnetic impulse in the form of a streamer into the air microseconds earlier than naturally formed streamers. Device confirmg to NFC 17-102 and UNE 21186 Standards. Appropriate non penetrating mounting arrangement. The device shall be mounted at suitable clear to the highest point on the roof top. (Model selected shall give coverage of 79 M radius @ min 5M height from terrace)
396	Down conductor:Supply, installation, testing and commissioning of 70 Sqmm twisted 19-Strand, bare Cu cable on surface/wall / as per site requirement and complete in all respect.
397	Lightning Counter :Supply and installation of counting the number of lightning strikes without any power supply.
398	Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
399	Test Link :Supply and installation of test link in weather proof IP 65 BOX.
400	Supply, installation, testing and commisioning of 2 x 25W LED Aviation abstruction light medium bay type 62, complete with lamp, lamp holder, Condenser necessary connecting wire, 1 X 25 AV with all necessary hardware, accessories as required for complete installation. Rate shall include the cost of necessary steel structures , fixing arrangements in this item. Refer drawing.
401	Online UPS- Input supply: Three Phase, Output supply: Three Phase Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt
402	phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)\"s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to the relevant International standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC (
403	inductor (L) and a capacitor (C)) filters shall be included in UPS cost),extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port open protocol for BMS
404	integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and connectors and all required accoseries are inclusive of the cost). This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current.
405	d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like: Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load /UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location etc
406	60KVA (Each Power module shall be < 10 KVA)
407	MAIN L.T PANEL
408	SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. The panel shall be complete with name plate, earthing, numbering, danger plate etc. as per specifications and drawings as required. The panel shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to communicate statuslike ON/OFF/ Trip through Modbus/Ethernet for major component like ACB, MCCB, MCB & Multifunation meters.
409	The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers,microprocessor release for overload, short circuit, instantaneous & earthfaultprotection with Current & Voltage metering & LCD display.
410	Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of ACB(Icu=Ics=Icw=65 KA (1 sec).MCCB, with microprocessor release with LSIG protection functionand should not derate upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng current limiting feature, double break mechanism & capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)
411	INCOMING
412	1 Nos. 1250 Amp TPN EDO ACB 25KALSIG having S/C, E/F O/C protection, LCD Display having specs as per attached annexture From 800KVA Transformer havingR,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCBInbuilt Zone Slelective Interlocking function Multifunction Meter
413	1 Nos. 500 Amp TPN Moterized MCCB 25KALSIG having S/C, E/F O/C protection, LCD Display having specs as per attached annexture From 200KVA Solar Power Backup havingR,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction MeterReverse Power Relay Power Conditioning Device
414	1 Nos. 800 Amp TPN Moterized ACB 25KALSIG having S/C, E/F O/C protection, LCD Display having specs as per attached annexture From 200KVA Solar Power Backup havingR,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB Inbuilt Zone Slelective Interlocking function Multifunction MeterReverse Power Relay Power Conditioning Device
415	BUSCOUPLER
416	1 Nos. 800Amp TPN Motorized ACB 25KAhaving specs as per attached annexturehavingR,Y,B Phase indication Lamp with control MCB On, Off, Trip Status Indication with control MCB
417	BUSBARS
418	1 Nos. 1600 Amp FP busbars of aluminium alloy as per SLD.
419	1 Nos. 1000 Amp FP busbars of aluminium alloy as per SLD.
420	AUTO OPERATION OF INCOMER / BUSCOUPLERACB\"s.
421	Load Management through PLC
422	Contactor for Load Management System
423	Auto changeover.
424	Buscoupler switching.
425	Electrial & Mechnical Interlocking.
426	Synchonization through PLC
427	Contactor for Synchronizing System
428	Auto changeover and auto load balancing, load management, auto On and Off of DG set as per load requirement.
429	Buscoupler switching.
430	Electrial & Mechnical Interlocking.
431	OUTGOING
432	1 Nos. 630 Amp TP MDO ACB 25 KA, having specs as per attached annexture havingR,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCB
433	3 Nos. 630 Amp FP EDO ACB 25 KA, having specs as per attached annexture havingR,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCB HVAC + Projector Room + Spare
434	2 Nos. 400 Amp FP MCCB 25 KA, having specs as per attached annexture havingR,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCB FF + Spare
435	2 Nos. 250 Amp FP MCCB 25 KA, having specs as per attached annexture havingR,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCB L+P + Spare
436	3 Nos. 100 Amp FP MCCB 25 KAOn, Off, Trip Status Indication with control MCB Multifunction Meter STP + PL + Spare
437	2 Nos. 125 Amp FP MCCB 25 KAOn, Off, Trip Status Indication with control MCB Multifunction Meter UPS+Spare
438	6 Nos. 63 Amp FP MCCB 25 KAOn, Off, Trip Status Indication with control MCB Multifunction Meter EX LIGHT + LIFT +Spare
439	Short Circuit Breaking capacity should not less than 50KA.
440	RELAYS AS PER SLD
441	300KVAR HPFC PANEL
442	HYBRID Power Factor Correction SystemSupply, Installation, testing and commissioning of HYBRID APFC Panel, 3 phase 4 wire, 415 V, 50 Hz AC System for Ambient temperature -5°C to +40°C of following capacity with passive solution of 60% capacity and active solution of 40% capacity,3Phase 4 wire Hybrid Power Factor Correction Solution (with arrangment for neutral current balance) to achieve >0.99 lag and TDDI/THDV values within IEEE recommended limits.APFC should be designed as per IS 16636 Or IEC 61921. The active section and passive section shall work in sync to give optimized output. The degree of protection
443	of passive section should be IP 42, and of active section should be minimum IP 21.The switching device for APFC passive section should be through capacitor duty contactor and for the active compensation system shall be IGBT based with 3 level topology having 12 IGBT in inverter circuit. The active compensation system should filter harmonics from 2nd to 50th individual harmonic order and shall be selectable for the entire range. The active compensation system should have feature to improve PF correction and harmonic filtration having response time <25Micro second. The hybrid panel shall be indoor type floor mounted free standing totally enclosed, extensible, fabricated in compartmentalised designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process for powder coated of
444	approved shade ( RAL 7032-Siemens gray or as approved by Engineer-in- Charge), having front section (switch gear and control accessories) and rear section (capacitor and reactor), front and rear access, having suitable current carrying capacity, extensible TPN Aluminium alloy bus bar of high conductivity, DMC/SMC bus bar supports,bottom base channel of MS Section, fabrication shall be done in transportable section, entire panel shall have common copper earth bar of minimum size of 25mm x 5mm with 2 nos. earth studs, the earth terminals provided on the body of capacitor bank shall also be bonded to the main capacitor panel earth bus with 2 nos. 8 SWG or 6 SWG GI earth wires/ equivalent size of copper conductor cable, forced ventilation for maintaining temperature rise not more than 5°C from ambient, interconnections, connections with 14% detuned reactor andheavy duty 525 V ISI marked Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 & 2) APFC Panel shall be in compliance with IS :16636 & CPWD Specifications etc. as per below details.
445	(A) IncomersSuitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating Lamp set along with required Instruments and accessories with extended rotary handle and door interlocking arrangement. Current rating of the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards rating.
446	(B) Instruments & Indicationsi) 3-Phase current sensing APFC microprocessor relay/controller , advance 8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100 KVAR & above) with Communicationthernet/RS485/ SNMP port open protocol for BMS integration as per approved by Engineering in charge and havingdisplay of Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I, harmonics up to 31 level. 3 nos of dual core CT\"s accuracy class 1, 15VA at incomer of PCC Panel for APFC relay.
447	ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in manual mode. iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA, KVAR, THD-V & I, Frequency.iv) Suitable rating control transformer shall be provided for control andindication circuit. v) All components like control transformer, meter, relay and indicating lamp shall be protected by using suitable rating individual MCB\"s. vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS 1100 V grade, PVC insulated multi stranded copper control wire. (C) Bus Bars 1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity 1.25 times of incomer rating as per CPWD specification.
448	b) For Active Section : Dedicated HMI (Human Machine Interface) (Minimum 7 inch display) for controlling and communication and having display of Phase wise V, A, PF, Cos-Phi, KW, KVA, KVAR, THD-V , THD-I, harmonics up to 50th level.Communication Ethernet/RS485/SNMP port open protocol for BMS integration as per approved by Engineering in charge.
449	300 KVAR
450	Office Building L+P Panel
451	SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. The panel shall be complete with name plate, earthing, numbering, danger plate etc. as per specifications and drawings as required. The panel shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to communicate statuslike ON/OFF/ Trip through Modbus/Ethernet for major component like ACB, MCCB, MCB & Multifunation meters.
452	The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers,microprocessor release for overload, short circuit, instantaneous & earthfaultprotection with Current & Voltage metering & LCD display.
453	Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of ACB(Icu=Ics=Icw=65 KA (1 sec).MCCB, with microprocessor release with LSIG protection functionand should not derate upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng current limiting feature, double break mechanism & capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)
454	INCOMING
455	1 Nos. 250 Amp MCCB 16KALSIG having S/C, E/F O/C protection, LCD Display having specs as per attached annexture R,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCBInbuilt Zone Slelective Interlocking functionMultifunction Meter
456	BUSBARS
457	1 Nos. 250 Amp FP busbars of aluminium alloy as per SLD.
458	OUTGOING
459	13 Nos. 63 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCBPDB+ACDB +Spare
460	9 Nos. 32 Amp FP MCB 10 KA On, Off, Trip Status Indication with control MCBLDB +Spare
461	Short Circuit Breaking capacity should not less than 16KA.
462	RELAYS AS PER SLD
463	Office Building HVAC Panel
464	SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. The panel shall be complete with name plate, earthing, numbering, danger plate etc. as per specifications and drawings as required. The panel shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to communicate statuslike ON/OFF/ Trip through Modbus/Ethernet for major component like ACB, MCCB, MCB & Multifunation meters.
465	The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers,microprocessor release for overload, short circuit, instantaneous & earthfaultprotection with Current & Voltage metering & LCD display.
466	Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of ACB(Icu=Ics=Icw=65 KA (1 sec).MCCB, with microprocessor release with LSIG protection functionand should not derate upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng current limiting feature, double break mechanism & capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)
467	INCOMING
468	1 Nos. 630 Amp ACB 16KALSIG having S/C, E/F O/C protection, LCD Display having specs as per attached annexture R,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCBInbuilt Zone Slelective Interlocking functionMultifunction Meter
469	BUSBARS
470	1 Nos. 800 Amp FP busbars of aluminium alloy as per SLD.
471	OUTGOING
472	20 Nos. 63 Amp FP MCB + 63 Amp 300mAmp FP RCCB On, Off, Trip Status Indication with control MCBODU +Spare
473	11 Nos. 63 Amp FP MCB 10 KA with 3-5KW S tar Delta Starter With Potential Free Contact to be operated as per Fire Alarm Panel Command On, Off, Trip Status Indication with control MCBVentilation & Pressurization Fan +Spare
474	Short Circuit Breaking capacity should not less than 16KA.
475	RELAYS AS PER SLD
476	UPS Output Panel
477	SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of adequate cross section through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a fully segregated, modular multitier arrangement with adequate size and distinct cable alley, bus bar alley/chamber. The panel shall be complete with name plate, earthing, numbering, danger plate etc. as per specifications and drawings as required. The panel shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to communicate statuslike ON/OFF/ Trip through Modbus/Ethernet for major component like ACB, MCCB, MCB & Multifunation meters.
478	The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers,microprocessor release for overload, short circuit, instantaneous & earthfaultprotection with Current & Voltage metering & LCD display.
479	Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of ACB(Icu=Ics=Icw=65 KA (1 sec).MCCB, with microprocessor release with LSIG protection functionand should not derate upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng current limiting feature, double break mechanism & capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)
480	INCOMING
481	2 Nos. 125 Amp MCCB 16KAR,Y,B Phase indication Lamp with control MCBOn, Off, Trip Status Indication with control MCBInbuilt Zone Slelective Interlocking functionMultifunction Meter
482	BUSCOUPLER
483	1 Nos. 125 Amp FP MCCB
484	BUSBARS
485	2 Nos. 160 Amp FP busbars of aluminium alloy as per SLD.
486	OUTGOING
487	8 Nos. 32 Amp FP MCB On, Off, Trip Status Indication with control MCBUPS DB +Spare
488	Short Circuit Breaking capacity should not less than 16KA.
489	RELAYS AS PER SLD
490	Supply Installation Testing and Commissioning of 400mm sweep 1500RPM energy efficient BLDC fan with double ball bearing for longer life similar to CGE RENESA or equivalent.
491	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator)
492	8 way Double door
493	Fire Alarm System :
494	Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System)and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.
495	Two Loop
496	Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.
497	Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.
498	Supplying, installation, testing & commissioningof intelligent analog addressable photothermal (Smoke) detector complete with mounting base complete as required.
499	Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.
500	Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Road Construction Tenders

Paver Blocking Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Work Of An Auditorium With A Capacity Of 800 Persons On 10,000 Sq. Meter Vacant Land In The Government Inter College Campus Near Mahavir Chowk In Muzaffarnagar District Under The Jurisdiction Of Development Authority Muzaffarnagar., Muzaffarnagar-Uttar Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Work Of An Auditorium With A Capacity Of 800 Persons On 10,000 Sq. Meter Vacant Land In The Government Inter College Campus Near Mahavir Chowk In Muzaffarnagar District Under The Jurisdiction Of Development Authority Muzaffarnagar., Muzaffarnagar-Uttar Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us