Conservation And Site Management Plan Of Shri Conservation And Site Management Plan Of Shri Ballaleshwar Temple, Pali, Tal. Sudhagad, Dist. Raigad= 1 Dismantling the existing lights, tublelight, bulbs, fans, independent plug points, wiring including circuit mains of all types along with accessories etc. complete as per specification No.WG-DM / PW 2 Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/ structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:-(1) The elevational area of the scaffolding shall be measured for payment purpose.(2) The payment will be made once only for execution of all items for such works. 3 providing and laying green net of minimum shade dencity 75 percent as per requrinment on site as per instruction by engr incharge 4 Removing the existing cement/ lime plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 m or spreading in the compound and cleaning the site etc. complete. 5 Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground within 50 metres lead. 6 Dismantling the R.C.C. Work 1: 2: 4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. 7 Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete.. 8 Removing iron pipe railing having wooden or R.C.C or C.C or iron posts and stacking the materials as directed etc. complete. 9 Removing cement tiles or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all lead, lifts, etc. complete. 10 Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete. 11 Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. 12 Removing G.I. or A.C. sheet roofing including purlins, principal rafters etc. including sorting service able and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etc. complete. 13 Removing R.S. girders of any size and span lowering the same and stacking neatly wherever directed in the compound scaffolding etc. complete. 14 Dismantling brick masonary in lime or cement mortar and stacking the materials as directed with all lead, lifts, etc. 15 Dismantling stone masonary in lime or cement mortar including stacking the materials as directed with all lead, lifts, etc.. 16 Lowering down carefully existing stone masonry of the monument manually in proper order including shifting the stone elements up to a distance of 50 meter beyond the monument area and stacking them as directed by Engineer in-charge, removing building rubbish and cleaning the site etc. complete. 17 Excavation for foundation in hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete (lift upto 1.50 m) By Manual Means. 18 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. 19 Providing and laying cast in situ 1:2:4 Lime Concrete of trap/ granite/ quartzite/ gneiss metal for foundation and bedding as per detailed specifications and drawings or as directed including bailing out water, centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required with fine aggregate, preparing the lime mortar in lime miller and then mixing with coursed aggregate in drum mixer as per specifications including bailing out water, watering etc. complete. 20 Filling in plinth and floors with approved excavated material in 15 cm . To 20 cm. layers including watering and compacting etc. complete. 21 Conveying the excavated materials, debris of brick or stone masonary, R.C.C. slab, water proofing, stone members/ materials, cement/ lime concrete, tiles/ marbles/ stone slab/ brick bat coba, etc. upto 2.5 km, away from the site and cleaning the site properly. 22 Clean or remove the dust cement plastercolour patches or any other cement or lime patches from the any stone surface with nichesgroovesmoulds architectural designs by using dry/ micro dry/ wet air abrasion method using calcium silicate particlesAluminium silicate particles any crushed stone particles crushed calcium carbonate particles mineral slag copper slagcoconut, almond shells particles glass beads Aluminium oxide particles, It is binding to use any of the above mentioned material with any number of coats until surface gets clean as per the requirement of site engineer, deputed conservation architect. This process includes all required tools, equipment and machinery of any shape and size as per stone surface requirement. This also includes all materials like potable water and scaffolding. At the end clean the surface by using water jet pump. 23 Providing general pest control services to the building to control the nuisance of cockroaches, lizards, pin bores and other insects, etc. with 4 operations in a year and monthly checkup. 24 Providing anti termite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6 mm dia. drilled at a distance of 30 cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. 25 Providing antitermite treatment to the wooden frames of doors/windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting150ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. 26 Providing antitermite treatment to the joints of wooden beams / joist used for the roof work of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 80ml. of chlorodane 5%W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. 27 ProvidingpreconstructionalantitermitetreatmentasperI.S.6313(Part-II)bytreatingthe bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percentofchlorophyrifospersquaremeterofsurfaceareacovering10yearsguaranteeon bond paper. 28 Providing and fixingIndian T.W Columns, beams of size 0.30 x 0.30 andmin height - 4.50 m (12 x 12 inch x 15ft) for roofing/ floor/ any wooden members including scaffolding if necessary etc. complete.“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 29 Providing and fixingIndian T.W beams and Stringer beams of size beam- 0.20 x 0.10 - upto 5 m(7.87 x 4 inch x17ft) for wooden members including scaffolding if necessary etc. complete.“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 30 Providing and fixingIndian T.W rafters of size length 0.075 x 0.075 - upto 5 m (2.95 x 2.95 inch x17ft) thick for roofing/ floor/ any wooden members including scaffolding if necessary etc. complete.“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 31 Providing and fixingIndian T.W Purlins, frames and floor joists, and secondary beams of size length 0.125 x 0.075- upto 3.20 m(4.9 x 2.95 inch x 11 ft) for roofing/ floor/ any wooden members including scaffolding if necessary etc. complete.“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 32 Providing and fixingIndian T.W Battensof size (0.025 x 0.025 (1 x 1 inch) thick length 3 m ) for roofing wooden members including scaffolding if necessary etc. complete.“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 33 Providingstructuralsteelworkinhollowsectionofvariousthicknessandsizesinsquare, rectanular and round shape from 25mm to 450mmsection as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete. 34 Providing and fixing solid wooden door of thickness 0.15 m including frame,fixing Big and small motifs, defensive bolts, pivot and pointed nails and providing steel roller, track for movement of wooden shutter etc. complete as directed by Engineer in charge 35 Providing and fixing solid wooden door of thickness 0.050 m including frame,fixing Big and small motifs, defensive bolts, pivot and pointed nails and providing steel roller, track for movement of wooden shutter etc. complete as directed by Engineer in charge 36 Providing and fixing jaali wooden door of thickness 0.050 m including fixing 8mm dia MS round bars,frame, pivot and providing rust proof paint to iron patti, pointed nails, steel roller, track for movement of wooden shutter etc. complete as directed by Engineer in charge 37 Providingandapplyingmelaminepolishofrequiredfinishtothewoodworkbyspray machineincludingknottingandpreparingtheevensurfacebyscraping,applyingFrench polish , scaffolding if required etc. complete.Note:The work to be executed on prior approval of Superintending Engineer will be necessary. 38 Providing & applying Polyurethane based wood coating to the new or old work in two coats including knotting, preparing the surface by scrapping, scaffolding etc. complete as per manufacturers specifications and as directed. 39 Providing and fixing teak wood railing of 1.05 m height in the temple mandap as per detailed drawings with top and bottom rails of size 0.075 x 0.15m andbalusters of 0.05 x 0.05m, each supported by the vertical newel posts of0.075 x 0.15 x 1.05 m with newel cap of size 0.1 x 0.1mas directed by the Engineer, removing the existing railing members and fixtures, including french polishing, and hardwares and joinery etc. complete. (Note: The work to be executed on preapproval of conservation architect). 40 Providing and fixing 50 mm.(1½″) thick Teak Wood Flooring or Planking for floor, as per detailed specifications and drawings or as directed including the thoroughly seasoned and greatest length best Moulmein teak boards, boards to be 38 mm. (1½″) thick and from 10 m. to 15 cm. (4″ to 6″) in width, side joints to be tongued and grooved or tongued and ploughed as may be specified, heading joints to rest upon the joist below, to break joint with one another and to be rebated and tongued together, the boards to be jammed together by flooring clamps, each board to be secured in position by two 2½″ screws screwed to each of the joists below, the heads of all screws to be countersunk and the exposed surface of boards then planed quite smooth, etc. complete. “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 41 Providing and fixing 25 mm.(1½″) thick Teak Wood Flooring or Planking for ceiling, as per detailed specifications and drawings or as directed including the thoroughly seasoned and greatest length best Moulmein teak boards, boards to be 38 mm. (1½″) thick and from 10 m. to 15 cm. (4″ to 6″) in width, side joints to be tongued and grooved or tongued and ploughed as may be specified, heading joints to rest upon the joist below, to break joint with one another and to be rebated and tongued together, the boards to be jammed together by flooring clamps, each board to be secured in position by two 2½″ screws screwed to each of the joists below, the heads of all screws to be countersunk and the exposed surface of boards then planed quite smooth, etc. complete. “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 42 Providing and fixing 75 mm.(1½″) thick Teak Woodfor decorative elements like arches , as per detailed specifications and drawings or as directed including the thoroughly seasoned and greatest length best Moulmein teak boards, boards to be 38 mm. (1½″) thick and from 10 m. to 15 cm. (4″ to 6″) in width, side joints to be tongued and grooved or tongued and ploughed as may be specified, heading joints to rest upon the joist below, to break joint with one another and to be rebated and tongued together, the boards to be jammed together by flooring clamps, each board to be secured in position by two 2½″ screws screwed to each of the joists below, the heads of all screws to be countersunk and the exposed surface of boards then planed quite smooth, etc. complete. “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” Including carving, moulding, etc complete 43 Providing and fixing Ductile iron Man Hole Covers/ Strom Water Grating and Grating with frame of Various sizes, weight and types and load bearing capacity as per EN-124, equivalent NECO with prior approval of concerned Superitending Engineer. 44 Providing and Fixing Decorative / Ornamental grills as per design for compound wall / Fencing including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc. complete as directed. 45 Providing Un-coursed Rubble Masonry of trapstones in lime mortar 1:1½, in foundation and plinth as per detailed specifications and drawings or as directed including the stones to be set in the work as received from the quarry, after merely knocking off weak corners and edges with the masons hammer, the stones shall be carefully laid so as to break joints, no joint shall exceed 12.5 mm. (½″) in thickness, every stone shall be set flush in mortar, the face stone shall be for greater size, and good beds, one through stone shall be inserted at least every 0.80 sq. mete (1 square yard), the joints shall be racked out carefully at least 25 mm. (1″) where pointing or plastering to be done, striking joints where no pointing or plastering is to be done, preparing the lime mortar in lime miller, bailing out water, watering and all exposed masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 46 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Flooringas per the site requirement of size of stone [0.60 x 0.45 x 0.15 Meter] (24 x 18 x 6) asper detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 47 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Bracketsas per the site requirement of size of stone [0.60 x 0.45 x 0.30 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 48 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Chajja as per the site requirement of size of stone [0.90 x 0.60 x 0.21 Meter] (36 x 24 x 8.5) as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 49 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Walls, Parapetas per the site requirement of size of stone [0.60 x 0.45 x 0.30 Meter] (24 x 18 x 12) as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 50 Providing Semi-circular Coping Cut-stone Second Sort, 22.5 cm. (9″) height and 52.5 cm. (1ꞌ9″) wide of trap / granite stones in lime mortar 1:1½ with size of stone [0.75 x 0.55 x 0.20 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the stone shall be dressed full or to template, exposed face of the stones shall be fine rough tooled, semi-circular and all joints shall be in line and close and not more than 3 mm. (⅛″) thick, preparing the lime mortar in lime miller, scaffolding, watering and all coping work when handed over to be perfectly clean and free from all mortar stains etc. complete. 51 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Talkhadaas per the site requirement of size of stone [0.50 x 0.50 x 0.30Meter] (18 x 18 x 12) as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 52 Providing Ashlar Fine Masonry of trap stones in lime mortar 1:1 for Domeas per the site requirement of size of stone [0.45 x 0.30 x 0.15 Meter] (18 x 12 x 6) as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 53 Providing/Re-setting Ashlar Fine Masonry of reuse-stones in lime mortar 1:1 in superstructure as per detailed specifications and drawings or as directed including the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course, the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 54 Providing Block In Course Masonry of trap (black basalt) in lime mortar 1:1½ with size of stone [0.45 x 0.35 x 0.20 m] (18 x 14 x 8) for steps as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the face of stones shall be rough-tooled, rustic (with or without chisel draft, except at quoins), or chamfered as specified, the beds and joints of all ashlar stones to be dressed perfectly true, square and full, headers shall not be less in length than breadth of ashlar stone plus 45 cm. (1ꞌ6″), the stones shall be set in mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 17.5 cm. (7″) in height, the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, bailing out water, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 55 Providing Ashlar Rough-tooled Stone Steps of trap / granite stones in lime mortar 1:1½ with size of stone[0.60 x 0.40 x 0.213 Meter]as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the stones shall be of exact size and shape, the shall be rough-tooled on exposed surface, holes for balusters should be cut in the steps before they are laid, each stone shall rest at least 3.8 cm. (1½″) on that below it, the beds or joints being in no case more than 3 mm. (⅛″), preparing the lime mortar in lime miller, watering and all steps work when handed over to be perfectly clean and free from all mortar stains etc. complete. 56 Providing/Re-setting Ashlar Rough-tooled Stone Steps of reuse-stones in lime mortar 1:1½ as per detailed specifications and drawings or as directed including each stone shall rest at least 3.8 cm. (1½″) on that below it, the beds or joints being in no case more than 3 mm. (⅛″), preparing the lime mortar in lime miller, watering and all steps work when handed over to be perfectly clean and free from all mortar stains etc. complete. 57 Providing and fixing Trap Stone Paving, Second Sort in lime mortar 1:1, with size of stone [0.60 x 0.45 x 0.15 meter] (24 x 18 x 6) , as per detailed specifications and drawings or as directed including all stone slabs to of approved quality, hard, even, sound, durable and uniform thickness, the stones to be very finely chisel-dressed on the surface and the course to be of prescribed width, the joints running true, the stones to be laid with joints not exceeding 6 mm. (¼″) thick and to be evenly and firmly bedded flush in mortar on the concrete and no hollow left, side to be dressed true and as per shape at least half the depth from the face, preparing the lime mortar in lime miller, watering and all paving work when handed over to be perfectly clean and free from all mortar stains etc. complete. 58 Providing Ashlar Arching of trap / granite stones in lime mortar 1:1, with size of stone 0.60 x 0.45 x 0.30 (24 x 18 x 12) as per detailed specifications and drawings or as directed including the arch stones be of approved quality, colour, hard and free from defect of any kind, the arch stones in all cases of the entire thickness, the arch stones shall be dressed full and true to their proper shapes with the necessary summering, twist or winding and be set in fine mortar, the intrados, joints and beds to fairtooled and left full, the cast or keying course to be accurately fitted, at all horizontal joints the intrados to have a 2 cm. (¾″) chamfer, the face stone may be tooled or rock-faced with or without chamfer as directed, in arches up to 60 cm. (2ꞌ) in depth all stones shall be of the full thickness of the ring, arches to be built on proper centring, the bed joints shall be radial and the side joints shall be at right angles to the bed joints and the thickness of the joints shall not exceed 5 mm. (3/16″) preparing the lime mortar in lime miller, cantering/scaffolding, watering and all arch work when handed over to be perfectly clean and free from all mortar stains etc. complete. 59 Making of moulding/ grooving/ chamfering on the surface of the formed stone member, as per given design or drawing, by an expert, artisan craftsman, including light sand papering of the finished member if required. 60 Making of relief architectural carving on the surface of the formed stone member, as per given design or drawing, by an expert, artisan craftsman, including light sand papering of the finished member if required. 61 Providing Brick Masonry First Class in superstructure with size of brick 0.20 x 0.15 x 0.07 in lime mortar 1:1½, as per detailed specifications and drawings or as directed including the bricks to be of uniform size, moulded ground, thoroughly well burnt and sound, ringing clearly when stuck with trowel, the bricks to be soaked in water for 12 hours before used, the bricks are to be laid flush in mortar in such bond as directed, as far as possible, bricks of uniform colour are to be selected for the face work when it is not to be plastered, the joints are not to exceed 12.5 mm. (½″), no bats or half brick to be used in the work, racking out joints where pointing or plastering to be done, striking joints where no pointing or plastering is to be done, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. 62 Providing and laying cast in situ 1:1:4 Lime Concrete of broken brick metal for coping or waterproofing as per detailed specifications and drawings or as directed including centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required, with fine aggregate, preparing the lime mortar in lime miller and then mixing with coursed aggregate or surkhi in drum mixer, the concrete must be bitten for two days with pouring water as per specifications, scaffolding, watering and all concrete work when handed over to be perfectly clean and free from all mortar stains, etc. complete. 63 Providing injection grouting with a slurry of lime and fine screened sand in proportion 1 : 1 with a proper pressurized jet pump, including cleaning, washing and packing the exisitng cracks or holes in the brick or stone masonry properly upwards with the slurry, scaffolding, curing etc. complete 64 Providing Lime Pointing to stone work in lime mortar 1:1 in superstructure, as per detailed specifications and drawings or as directed including all face or visible work shall be pointed, unless otherwise specified and shall be done while the mortar is fresh, the mortar shall consists of lime and fine sand shall not be ground fine but sand should be finer, the joints of the pointed work shall be neatly defined by the pointing, the lines shall be regular and uniform in breadth and the joints shall be raised or flat as may directed, preparing the lime mortar with 640 gram pulp of wood apple (Belfruit) per cubic metre of lime mortar as a bonding material, scaffolding, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete 65 Providing 12 mm. thick Rough Cast Lime Plaster in single coat in lime mortar 1½:1 in superstructure, as per detailed specifications and drawings or as directed including all joints in masonry and brick work are to be racked out to a depth of at least 20 mm. and the wall to be washed with fresh water and thoroughly wetted for six hours before plastering, the plaster to be applied in an even and uniform coat well pressed in to the joints and to be well beaten for 1½ days with hand tappers, the plaster should also be well sprinkle during the proses of beating with a mixture of 1.10 kg jaggary and 640 gram pulp of wood apple (Belfruit) in 90 to 135 litre of water, the plaster being wetted occasionally with fresh water while the beating is in progress, all exposed angles and junctions with door frame to be carefully finished, all mouldings shall be worked true to template and drawn neat, clean and level, soffits of arches must true arch of circle, preparing the lime mortar in lime miller with 1.60 kg Gugal (a kind of fragrant gum) and 960 gram chopped hemp (fibre of bhendi or tag ) per cubic metre of lime mortar as a bonding material, of lime as a bonding material, scaffolding, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete. 66 Stucco work in lime, surkhi and sand (1:1:1) as per traditional practices and design, the mortar should be prepared by grinding mill only. The thickness varies from 10mm to 100mm as per design. 67 Providing and applying integral fine coat, with addition of colour pigments, as paint to the plain lime stucco plaster in 2 layers, including scaffolding, curing, all leads and lifts, etc. complete. 1) The first coat to be laid is a mixture of fine lime and white washing lime in proportion of 2:1,made smooth with wooden rubbers and very lightly beaten. 2)The finishing coat consisting of fine lime, white washing lime, mixed with the appropriate pigment in 1:2:1 proportion is to be applied and well polished with trowels. 68 Providing and applying antifungal wash treatment using 3% solution of sodium pentachlorophenate, of reputed brand and manufacturer, on cleaned sand stone surface at desired locations as per direction of Engineer-in-charge (The rate is inclusive of all materials & labours involved except scaffolding). 69 Application of water, oil and stain repellent, Non film forming, breathable, Water/Chlorophyllin based Protectguard MG of Killickguard or equivalent with brush on Stone Façade in two coats. Applications to be done 70 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete (300 mm dia. R.C.C. pipe) 71 Providing and laying Hyperplas standard or equivalent polymeric multiple monolithic five layer water proofing flexible, pliable and high tensile strength membrane (3 Kilogram/ One Square Metre) & consist of centre core of 90 micron thick High Molecular High density Polyethylene film (HMHDPE) which is protected on both the side with polymeric mix. Applying the membrane by thermofusing to roof & parapet after applying thin film of hot blown bitumen 85/25 or 90/15 grade @ 1.2 Kilogram/ One Square Metre maximum as per surface condition or Hyperplas primer @ 250 gms/ One Square Metre as per site condition on the surface to be treated with 10 cm overlapping including finishing etc. complete and covering guarantee of 7 years on stamp paper of Rs. 100/- and as directed by Engineer-in-charge. (Prior permission of S.E.in writing is necessary before inclusion of this item in estimate). 72 Shingles on Roof : Providing and fixing shingles on Roof of size 17x40 inch to 13.1/4 B2042to 39.1/8 of asphalt. The material are resistance against fire and atmospheric aggressions and are developed using high quality material and cutting edge technology.R.A. Unit : 1 / Square Metre 73 Providing and fixing Teak wood Eaves Board 15 cm.(6″) wide and 12.5 mm. (½″) thick, as per detailed specifications and drawings or as directed including the planks to be best Moulmein teak to be 12.5 mm. (½″) thick and 15 cm.(6″) in width, of a uniform colour and planed, the planks to be laid truly parallel to the floor so as to cover the end rows of the tiling and to be fixed with screws of the proper length driven countersunk, all joints to be neat and close, scaffoldingetc. complete. “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” 74 Providing andfixing colourcoatedZincalume (R)AZ150(min150gms/sq.mt.totalon each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength,metallichotdipcoatedwithAluminium-Zincalloy(55%aluminium 43.4%zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganicpigment).Thepaintshallhaveatotalcoatingthicknessofnominal35um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center- to-center.The endribshallbedesignedforanti-capillarygroove.andreturnleg.Thefeed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre) 75 Galvanised iron sheet 1 mm (20 B.W.G.) eaves precoated gutter 200 mm to 230 mm wide and 100 mm to 125 mm deep moulded or half round girth upto 600mm including iron rods, on the edges (throughout the length) and galvanised iron sheet ferrules with fixtures, for outlets wherever required clamped using W.I. clamp 38 mm x 3 mm fixed 1.0 m C/C including making necessary connections with rain water pipes etc complete and as directed. 76 Providing andfixing 10cm C.I.NahaniTrapincludingC.I.gratingbendandpiece ofC.I. pipe upto the outside face of the wall complete. 77 Supplying and Fixing 100 mm internal dia. 4.0 mm thk. (weight approx.10.0 Kg./Rm.) centrifugally cast C. I. pipes Confirming to IS 3989, sockets spigots type pipe for rain water/soil waste and ventilation with all fittings including scffolding, 1 : 1 CM jointing proper embedding and fixing on wall & column etc complete as directed. 78 Supply and Installation of translucent roof with DPI Flux standing seam multicell polycarbonate panel system. The system with complete assembly of co extruded UV protected multicell panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of min 12 mm thick of 900 mm (min.) width with angular daylighting concept. Panels shall have minimum six layers with truss bridge design for higher flexibility & strength. Panels with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical standing seam at both sides of the panel. Panels shall be fixed on Purlin with snap on connectors with double tooth grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 One Numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.6 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Colour: As per Approval. Approved Make: FLUX by DPI Daylighting or approved equivalent The 12mm thick panels shall be used for a roofing height of upto 15 mtrs. 79 Providing and fixing Country cut teak wood partly veneered and partly glazed partition with 75mmx50mmframeat60cmcenterand9mmthickcommercialplyonbothsides, decorative veneer of 4 mm thick and plain glass 5 mm thick, including French polishing etc.complete 80 Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 81 Free Standing Table @ 1500Lx600Dx750HTProviding and fixing Table of Size 1500 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board.All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :-Metal Powder Coated - Black Color, CPU TROLLEY :-Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, 82 Providing & Arrangemnt of MiId Back chair, Normal SyncroMechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery 83 Public Seating Chair. - 3 SeaterProviding and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. 84 Providing cultural and directionalsignage for information dissemination about the temple in GRC as per the design and location provided by the conservation architect. 85 Providing and fixing Directional & Instructional Signage in the acrylic board to be used indoor spaces. SS screws to be used for fixing the signage to the wall/ wooden surface.. 86 Providing lettering as part of the signage (Cultural, directional and informatory) for information dissemination about the fort in GRC as per the design and location provided by the conservation architect. 87 Providing 120 litre SS litter bins of approved quality and design as per conservation architect of size 0.90 x 0.50 x 0.90 m in desired location 88 ProvidingandlayingCastinsitu/ReadyMixcementconcreteinM-10oftrap/granite/ quartzite/gneissmetalforfoundationandbeddingincludingbailingoutwater,Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided,finishingifrequiredandcuringcomplete,withfullyautomaticmicroprocessor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade) 89 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-30oftrap/granite/quartzite/gneissmetalforR.C.C.workinfoundationslike raft,strip foundations,grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steelcenteringformwork,cover blockslaying/pumping, compactionfinishingtheformedsurfaceswithcementmortar1:3ofsufficientminimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic microprocessorbasedPLCwithSCADAenabledreversibleDrumTypemixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 90 Providing and laying Cast in situ/ Ready Mix cement concrete M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, coverblocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 91 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-30oftrap/granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or asdirectedincludingsteelcentering,formwork,coverblocks,laying/pumping, compactionandrougheningthesurfaceifspecialfinishistobeprovidedandcuringetc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 92 ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-30oftrap/granite/ quartzite/ gneiss metal for R.C.C.slabs andlandingsasper detaileddesigns anddrawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 93 Providing and laying in-situM30 Grade unreinforced plain cement concretepavementover a prepared sub base with 43 grade cement , coarse and fine aggregate( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradationas per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcheras per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and gradesas directed by Engineer-in-charge and curingby curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top withdepth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. 94 Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete. 95 Providing and fixing in position TMT FE 500, 25mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 cms. Long and at 30.00 cm. C/C and wherever directedincluding handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete. 96 Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge. 97 Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 mOne Metric Tonneo 4 mm. joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer.(A) Contraction and longitudinal joints (15 mm. deep x 8 mm.wide) 98 Providing and fixing in position HCRM / CRS (CorrosionResistant Steel) bar reinforcement ofvariousdiametersforR.C.C.pilecaps,footings,foundations,slabs,beamscolumns, canopies,staircase,newels,chajjas,lintelspardis,copings,fins,archesetc.asperdetailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 99 Providing and Fixing mat finish stainless steel (of 302 grade ) railing with toppipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75mmdiameteretc.complete(PriorapprovalofsampleandbrandbyEx.Engineeris necessary before use) 100 Providing and installing the water cooler with Seam welded food grade Stainless steel body and tank, voltage overload compressor protection and adjustable thermostat, precoated outer body for corrosion resistance, cooling rate minimum 80 litres per hour and tank storage capacity 100 litres etc complete as per engineer incharge 101 ProvidingandfixingheavydutyinterlockingconcreteColouredpavingblocksof60mm thickness of having a strength of 300 Kilogram/Sq.cm. of approvedquality andshape ona bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete 102 Providing and laying in place 300mm x 300mm x 16mm cement tactile directional and warning tiles (for a person with visual impairment)of the approved brand and make and specified colour for outdoor floors such as footpath, courtyard, multimodals location etc. laid on 20mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes and patterns including grouting the joints with white cement with matching pigments etc. complete as per direction of engineer in charge 103 ProvidingandconstructingBrickMasonryInspectionChamber60cmx45cmx90cm including1:4:8cementconcretefoundation1:2:4cementconcretechannelshalfround G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75 Kilogram with lid and frame fixed in cement concrete 104 Providing secondclassBurntBrickmasonrywithconventional/I.S.typebricksincement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposedfaces, raking out joints on exposedfaces and watering etc. Complete. 105 Providing secondclassBurntBrickmasonrywithconventional/I.S.typebricksincement mortar1:6insuperstructureincludingstrikingjoints,rakingoutjoints,wateringand scaffolding etc. Complete 106 Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade withfullmoulding and three grooved line forthetreadsonbedof1:4Cementmortarincludingfloatfilling jointswithneatcement slurry curing polishing and cleaningetc. complete. 107 Providing and fixing partition with kadappa stone of all sizes and 25 mm thick polished on both side and edges to original including fixing in position in cement mortor 1:4 curing polish- ing, cleaning etc complete. 108 Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete 109 Providing and fixing solid core flush door shutter in double leaf 32 mm thick decorative type of exteriorgrade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete 110 Providing and fixing 30mm thickPVC FLUSH L DOOR SHUTTER consisting of panel of hollow PVC profile of 20 mm thickness consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mminserted inside the hollow section of stiles rails top ?and bottom railsandtwo19x19mm MStubesinsertedhorizontallyinsidethe hollowprofile section using 4/5 mm sheet using screws hollow profile shall be lipped with 10 mm (5mm x2) thickx20mmwidthonstilesandrailsusingsolventcement.Theinnerpanelshallbe laminatedwith5mm thicktermite proofwaterproof plain/prelam PVCsheet using solvent cementonthebothsidesofthepanelincludingstainlesssteelfixturesandfasteningetc. Complete as per direction of Engineer incharge, manufacturers specification and drawing. 111 Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended falseceilingconsistingofalluminiumT2”x1½”(50mmx40mm)weighing0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete. 112 Providing and fixing Country cut teak wood partly veneered and partly glazed partition with 75mmx50mmframeat60cmcenterand9mmthickcommercialplyonbothsides, decorative veneer of 4 mm thick and plain glass 5 mm thick, including French polishing etc.complete 113 Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. 114 Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete 115 Providing andconstructing granite kitchenplatform withfixing of stainlesssteelsink 600 mm x 450mm size as per detaileddrawing including vertical bothside polishedkadappah stone 25 to 30 mm thick supports with kadappahtop 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two verticalgranitesupports15cmheightandtopgraniteof75x40cmincludingcutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m) 116 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positionsincludingbasecoatof15mmthickincementmortar1:4usingwaterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping thesurfaceofthebasecoatroughtoreceivethesandfacedtreatment6to8mm thickin cementmortar1:4finishingthesurfacebytakingoutgrainsandcuringforfourteendays scaffolding etc.complete. 117 Providinginternalcementplaster12mm thickinsinglecoatincementmortar1:3without neeru finish to concrete or brick surfaces, in all position including scaffolding and curing etc. complete. 118 Providingandapplyingplaster/wallpunningwithplasterofparis(withplasterofparis material)in10to13millimeterthicknessto previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. 119 ProvidingandapplyingTextureplasterwithfinishingwithtexturematerial ofapproved makein 3 to 4 millimeterthickness on previously plastered surface, including Plaster Groove 6mmthicknessorTapeGrooves35to45mmthicknessorasrequired,inallposition including preparing the surface, scaffolding etc. complete. 120 Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist. 121 Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to oldplastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc.complete. 122 Providing and fixing white european type wall-hung, Size 360mm x 360mm x 575 mm with flush valvehaving flow rate up to 6.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalentmakeincluding PVC soil pipe, vent pipe upto outside face of wall, 100mm diaPVCplug bend inlet pipe all fittings,cutting & making good walls, floors etc as directed by Engineer in charge.( Make shall conform to manufacturers Green product and shall got approved from the Engineer In Charge.) 123 ProvidingandfixingOrissatypewhiteglazedearthenware575mmwaterclosetpan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. 124 Providing and fixing 15 mm diameter PVC Aqua kraft type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete 125 Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. 126 Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. 127 Providing and fixing coloured glazed earthenware Wash Hand Basin of 55cm x 40 cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. 128 Providing and fixing white glazed urinal with Pressmatic auto closing valvehaving flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalentmake with P.V.C. waste pipewith fittingarrangementetc.complete as directed by Engineer in charge.( Make shall conform to manufacturers Green product and shall got approved from the Engineer In Charge.) 129 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm 130 Providing and fixing in position powder coated aluminium louvered windows / ventilator of varioussizeswithpowdercoatingasperdetaileddrawingandspecificationsincluding aluminiumframes80x38mmx1.22mmboxtype,5mmthicksheetglasslouvers,of approved quality etc. complete. 131 Grab bars-Providing SS grab bars set for accessible toilets comprising of 4 nos. Grab bars as specified below.(1 nos. wing grab bar + 1 nos. L shaped grab bar + 2 nos. straight grab bars = 1 typical set) 27a) Swing grab bar (1 NOS) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 NOS) Providing S.S. 304 L SHAPED DISABLED GRAB BARof IZE-600MM (H) X600MM (D) and 32MM DIA. and thicknessmm of the approved brand and make.27c) Straight grab bar (2 NOS)Providing S.STEEL 304 GRAB RAIL (600 MM),32MM DIA. and thickness 1.5mm of the approved brand and make. 132 Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. 133 Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 134 Providingandfixing100mmdiastabiliserpipe/P.V.C.soilvent/wastepipeandwith necessary fixtures andfitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. 135 Sofa Set 3+1+1Providing & fixingSofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms)Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat 136 Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. 137 3 DRAWER PEDESTAL UNIT @ 392L x 450D x 680Ht. mm.3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board. 138 Low Height Openable Storage @ 900Lx450x750HT Providing and fixing Openable Steel Storage of 900 x 450 x 750Ht, with 2 adjustable shelves, Complete body & shutter made in0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns. with 25 mm. thk additional Top on top of storage as as per drawing 139 Book Case with Glass Shutter @ 825Lx300Dx1650HTProviding & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2mm thick CRCA with glass pannel in Powder coating finish as per drawing. 140 Tea Table 900mm X 750mm X 450mm for m.s. ante chamberProviding And Fixing Of Tea Table 900mm X 750mm X 450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made OutOf 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc. 141 Stainless Steel Pipe curtain rod . Providing & fixing of SS pipe curtain rodsincluding Brackets as per site in charge instructions & all necessary Fittings etc. completed 142 CurtainsProviding clothes for curtain of Bombay Dyeing/Binni/Mafatlal etc brands, stitching as per required size with Frill (Zaller) & fixing at required places ( including rings )Note:-Measurement would be taken as per actual length of window & default width ( i.e . 48” panha) Curtain (Material Synthetic Clothes & cost of clothes starting from Rs 250/- onwards) 143 Providing and fixing during laying in RCC Slabrectangular 2 mm thickM.S. sheet fan hook box ofsize 180x100 mm with required depth with holes or notches as required, bottom and top sides of 1.6 mm M.S. sheet fixed with 3.5 mm dia. round headed screws together with 12 mm dia. M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface 144 Providing and fixing H.D.P container one piece moulded water tank made out oflowdensitypolythylerandbuiltcorrugationincludingofdeliveryuptodestination hoisting andfixing of accessories such as inlet, outlet overflow of alltanks capacityabove 1000 to 20,000 litres 145 ProvidingwaterproofbeddingforflooringofBathandWC25mmthickinC.M.1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete. 146 Providing waterproof plaster in W.C. and bath12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete.(Excluding Tiles) (As directed by Engineer in Charge) 147 Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixedwithapprovedwaterproofingcompound.Markingfinishedsurfacewithfalse squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for requiredheight,withdripmouldatthejunctionofplasterandparapetandcuringand covering10yearsGuaranteeagainstleakproofnessonCourtfeestamppaperofRs.500/- including ponding test etc. complete. 148 Providingandlayingdampproofcourse50mmthickinM20cementconcretelayerand bitumen / using cement with waterproofing compound curing, formwork etc. complete. 149 Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/ One Square Metreasperdrawingincludingfixturesnecessaryweldingandpaintingwithonecoatof anticorrosive paint and two coats of oil painting complete. 150 Supply and Making of New Heritage Building Models In Acrylic /FRP material , Duco Painting , Artificial lawn and Surrounding Gardening work for Beautification of model,preparation of Base in Ply and other materials as per requirement of model by Instruction of Engineer In charge . Site Visit , Permissions and Approvals for models making , Drawings Preparation and Making . Providing and Fixing of MS Frame and Transparent Acrylic Cover to this Models . Transportation of material and Complete Model transportation at Museum/ location instructed 151 Providing and Fixing of Transparent Acrylic Cover For Heritage building Model include Cutting of Sheet as per require size, hole drill, Joint covering of Tape , installation of cover along with material transportation Cost . 152 Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 80 mm thickwith 3 mm diameter mild steel bar reinforcement, of approved design on both sides, fixing in cement mortar 1:3 and curing etc .complete. 153 Providing and fixing in position Terracotta Jali block wall as per desired shape as a decorative feature in interior as well as exterior, block size - 200 x 200 x 60, and weight of 2 - 2.5 kg for each block in natural red color. Jali wall to be installed in specific openings as a fenestration detail, with neccessary fixtures, chemicals etc completes as specified by the conservation arhitect.
