Tender For Special Repairs To Bldg No. 63 For Agniveervayu (Women) At 3 Brd Under Ge (Af) Mc Chandigarh; 1 Demolition of un-reinforced cement concrete exc 15cm thick on any description and in any positionnot other wise specially provided for and removing all demolished material/debris to 1.50Km form the site and depositing where directed complete all as specified and directed. 2 M&L for Plain cement concrete 1:7:12 , Type F2 (using 40mm graded brick aggregate)as in sunken filling and mass concrete complete all as specified and directed. 3 M&L for providing water proofing treatment of sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make as approval in Technical Instruction 5/2003 by adding :(a) 15mm thick plaster (1:4) cement sand mortar mixed with and including liquid water proofing compound @200ml per 50Kg bag by weight of cement on floor and wall / beam , finishing the surface even and smooth without using extra cement. The surface shall then be cured and allowedto dry. (Note: Water proofing compound shall be measured and paid separately). (b) First layer of slurry of cement @0.488 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hrs.(c) Second layer of slurryof cement @0.242 kg/sqm mixed with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hrs followed with water curing for 48 hrs and including demolition of existing treatment or flooring and removal of all rubbish outside defence land upto a distance exc 1.5Km but n.exc 5Km, complete all as specified and directed. 4 M&L for Plain cement concrete 1:3:6 , Type C1 (using 20mm gradedcrushed stone aggregate)as in sub base of floorscomplete all as specified. 5 Material and labour for cleaning and removal of dust,mud,algae,moss and other stains from roof tiles(brick/concrete) and parapetwith help of wire brush or mechanical means including scrubbing down with water. removal of all rubbish outside the defence land, complete all as specified and directed.Note:-Ensuring no damage to solar panel plate/arrangement fixed on roof. 6 Material and labour for brushing neat cement slurry with 3.00 kg of cement per square meter complete all as specified and directed.Note:- Ensuring no damage to solar panel plate/arrangement fixed on roof. 7 Material and labour for rendering20mm thick in cement mortar (1:3) usingWPC @ 200ML per 50Kg bag of cementon surfaces of roof and parapet, finished even & fair without using extra cement, Ensuring no damage to solar panel plate/ arrangement fixed on roof, complete all as specified and directed. Note :-WPC shall be measured and paid separately. 8 Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-charge. 9 M & L for providing,mixing and applying Dr.fixit/Fosroc/Asian Primer AC with 10% water dilution with clean portable water,and applying with roller or brush coverage at the rate 7.0 to 8.0 sqm per litre/coat, allow the primer to dry for 04 hrs. And applying a coat of Dr.fixit/Fosroc roof seal select (diluted with water in the ratio 2:1) self priming coat at the rate 8-10 sqm/litre/coat in the SSD(Saturated surface Dry) condition.Apply 1st coat of Dr.fixit/Fosroc roof seal select at the rate of 0.45-0.5/litre/sqm/coat. Supply and Laying a 45 Gsm glass fibre mesh of 2.5mmX2.50mm sandwiched between the first and second coat.While the first coat is still wet. Allow the frist coat to dry for 4-6 hrs. Apply second coat of Dr.fixit/Fosroc roofseal select with the same application coverage.Application direction of second coat coat should be perpendicular to the first coat .Allow second coat to dry for 4-6 hrs.Apply third coat of Dr.fixit/Fosroc roofsealselect at an application direction that is perpendicular to that of the second coat with the same application coverage rate to achieve total dry film thichness of 900 to 1000 microns at forced coverage at the rate of 1.50-1.60 litre/sqm in 3 coats. Check to see no void surface is untreated/uncoated. Allow the system to air cure for 7 days minimum. The material havingfollowing technical properties: Attains a tesile strength with fibre N/mm 2=6-8 as per ASTM D 2370; Elongation at break = 200% as per ASTM D 2370, Crack bridging ability up to 2mm,Shore-A hardness 80 as per ASTM D2240-2015, Tear Resistance with fibre N/mm 34 as per ASTM D 624. The system comes with 10 year waterproofing warranty from M/S Pidilite Industries/FOSROC/Asian.complete all as specified and directed by Engineer-in-charge. 10 Taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortar surfaces of RCC columns, beams, walls, chajjas etc and exposing the reinforced cement, wire brushing and cleaning the exposed steel reinforced bar, apply rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified cement and quartz sand mortar in CM 1:3 mix, 40mm average thick in two coats, with and including polymer @10% by weight of cement, including necessary steel scafolding for carrying out the work upto height of 12.0 metre (Appx) complete all as specified and as directed. Note : Reinforcement shall be measured & paid separately. 11 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 12 M&L Glazed ceramic coloured tilesin vertical surfaces of size 350 x 250x 7mm /450mm x 300mm x7mm thick set and jointed in neat cement slurryover and including 10 mm thick rendering in cement mortar 1:4for receiving the tilescomplete all as specified complete all as specified. 13 M&l fornon skid ceremic tiles 7 to 8mm thick square/ rectangular area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed bed for floor finishes in cement mortar 1:4complete all as specified complete all as specified. 14 Demolition of stone slabs of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete removal of debris outside MD land complete all as specified and as directed. 15 Materials and labour for 15-18mm thickgranite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, urinal partitions, cooking plateform and like over and including 15 mm thick screed in cement morter (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as apecified and directed. 16 Providing edge moulding to 15-20 mm thick stone(any description) of counters vanities etc, including machine polishing to edge to give high gloss finish etc. Complete all as specified and directed. 17 M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete over and including 15mm thick screed bed in cement mortar 1:4complete all as specified and directed. 18 M&L Machine cut Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and finish complete over andincluding 10 mm thick screed bed in cement mortar 1:3all as specified. 19 M & L for Grinding& polishing of old kota stone/ marble/ baroda green floor/skirtingwith machine to mirror finish in and including making good of wall finishes as per original specifications complete all as specified and directed. 20 Demolitionof reinforced concretesuch as roofs, floors,beams, staircase,landing,chajjas,facia and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed. 21 M&L forreinforcedcementconcrete 1:2:4 type B1 (using 20 mm graded crushedstoneaggregate ) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed. 22 M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200mm thick (Horizontal or sloping) for rough finish surface of concrete. 23 M&L for mild steel TMT bars 10mm dia & over, cut to length, bent to shape reqd including cranking, bendingspecially for columns, hooking ends & binding with MS wire annealed not less than 0.9 mm dia, including necessarywelding as required at site complete all as directed and specified. 24 M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape reqd including cranking, bendingspecially for columns, hooking ends & binding with MS wire annealed not less than 0.9 mm dia, including necessarywelding as required at site complete all as directed and specified. 25 Demolition of brick work masonry, built in cement mortar including dismantling all quions,arches, pillars etc complete all as specified and directed. 26 M&L for brick work with sub class B bricks, straight/curved on plan exc 6M mean radius built in cement mortar 1:6 complete all as specified. 27 M&L for brick work with sub Class ‘B’ bricks straight or curved on plan exceeding 6m mean radius in half brick thick built in cement mortar 1:4 in any location, complete all as specified and as directed. 28 Taking down cement plaster on brick/stone walls of any layer up to masonry work etc including raking out joints, hackingfor key scrubbing down with water etc complete all as specified and directed. 29 Material and labour 10mm thick rendering cement plaster in Cementmortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement and providing necessary scaffolding , safety precautions and other requisite arrangements complete all as specified and directed. 30 M&L for Rough cast plaster After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick andwhile it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravelaggregate (which is generally of size between 6 to 12 mm depending on the texture required)mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensurethat larger aggregates are thoroughly covered complete all as specified and directed, including taking down cement plaster of any layer up to masonry work and racking out joints, hacking for key scrubbing down with water etc, complete all specified and directed by Engr-in-Charge. 31 M & L for15mm thick rendering in Cement and Sand mortar 1:4 over concrete /brick surfacesfinished fair and even without using extra cement includingtaking down cement plaster from brick walls or concrete surfaces of any layer up to masonry work, raking out joints, hacking out for key, scrubbing down with water and providing necessary scaffolding , safety precautions and other requisite arrangements all as per site requirement complete all as specified & directed. 32 M&L for Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth without using extra cement on ceiling in cement mortar 1:3 complete all as specified and directed. 33 M& L for prepaing new plastered surfaces of wall and applying 2mm thick wall care putty andtwo coats ofoil bound distemper over a coat of alkali resistant primer at any height including necessary scaffolding etc complete all as specified and as directed. 34 M&L for preparation ofnew plastered/concrete surface of wall/chajjas/facia and applying two coats of exterior emulsion paint over one coat of primer to be applied using an airless spray machine upto any height including necessary scaffolding etc complete all as specified and directed. 35 M&L for Preparation of newly plastered surfaces of Ceiling and applying two coats of oil bound distemper white or tinted over a coat of primer complete all as specified and directed by Engineer-in-Charge. 36 M&L for preparationof old plaster/concrete surfaces andleveling / edgesing the disturbed surface with water proofing putty and applying two coat of exterior acrylic emulsion weather proof treatment upto 15 Mtr height to be applied using an airless spray machine including necessary scaffolding etc complete all as specified and directed.Note : The tint and shade be as approved by the GE. 37 M&L for complete removal of existing treatment and applying two coats of Oil bound Distemper emulsion paint, white or tinted over one coat of primer over 1.00 mm thick of wall care putty as preparatory to distemper on surfaces of wall up to any heightincluding necessary scafolding and safety arrangements complete all as specified and directed. 38 M&L for preparation of old plastered surfaces of Ceiling and applying one coat of oil bound distemper complete all as specified and directed by Engineer-in-Charge. 39 Taking down chowkhats/frames exc 1.5 Sqm but n.exc 4 Sqm including shutters (without taking off shutters from the frames complete all as specified. 40 Taking down chowkhats/frames excn.exc 1.5 Sqm including shutters (without taking off shutters from the frames) including grill etc complete all as specified. 41 Refixing of shutters in the same opening includingtaking down and easing and adjusting,belding,oiling complete.exc 1.00 sqm and not exc 2.00 sqm 42 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) Complete all as specified as per Manufacturer broucher.MAKE : RAJSHREE, SINTAX, ECOCELL OR EQUIVALENT. 43 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. MAKE : RAJSHREE, SINTAX, ECOCELL OR EQUIVALENT. 44 S&F forPowder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions frames (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. 45 S&F forPowder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows (two or three track sliding/openable) & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. 46 S&F for Powder Coated aluminium grill of approved pattern cut to required size/shape and fixed with position with aluminium bedding & frame with & including U sections, fixed to aluminium door/windows/ventilators complete all as specified and directed. 47 Material and labour foraluminium composite panel sheet of 3mm thick which consists of 3mm thick thermoplastic core of anti-toxic LDPE sandwiched between 2 skins of 0.5mm thick aluminium foils with outer surfaces finished with 30 u PVDF and inner surface finished with a thin coat of polyester paint, fixed in panel to aluminium frame including all necessary frame work or powder coated snap beading and rubber gasket complete all as specified and directed.Make :- Alstone/Alex panel/Armstrong/Euroboard 48 Supply and fixing 4.80mm thick ordinary quality tinted glass,fixed to aluminum frame work in panels not exc 0.5 Sqm in each pane, complete all as specified & directed. 49 S&F 100 mm Aluminiumhandles Extruded aluminium alloy handles, fabricated type, anodised complete all as specified & directed. 50 Supply and fix180mm size powder coated (any tint) aluminium American Handle fixed to aluminium door with suitable screws, complete all as specified and directed. 51 S & F 100 mm size but hinges medium weight stainless steelomplete all as specified & directed. 52 S&F 150 mm size Aluminium , barrel tower bolt of extruded sectioncomplete all as specified & directed. 53 Supply and Fix, Aluminium anodised, barrel tower bolts 200mm long, powder coated, of extruded section and fixed, complete all as specified and directed. 54 Supply and fixing 150mm mild steelordinary rat rail rod pattern spring including roller and roller plate, fixed complete all as specified and directed. 55 Supply and fix, Aluminium alloy, anodised, Sliding door bolts 200mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia, complete all as specified and directed. 56 Supply and fixing brass mortice lock vertical type 100mm size, 6 lever fixed in aluminium shutter, complete all as specified and directed. 57 S&F 5mm thick Figured glass, pin head semi type and incl glazing with oil putty/aluminium beading with rubber gasket in squares n exc 0.5 sq. m in each pane 58 S&F 4mm thick Figured glass, pin head semi type and incl glazing with oil putty/aluminium beading with rubber gasket in squares n exc 0.5 sq. m in each pane 59 S&F of Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed Stainless Steel wire staples complete all as specified & directed. 60 S&F as in repair of Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with Stainless Steel wire staples complete all as specified & directed. 61 M & L for old steel painted surface of any description over 10 cm in width or girth and applying one coats of synthetic enamel paintall as specified and directed. 62 M&L for preparation of old wood or wood based surfaces over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed. 63 S&F factory made 18mm thick solid WPC (wood polymer composite) board of density 650kg/cum of one side prelaminatedwith any colour and other sidebalancing lamination, as in cupboards/kitchen/ cabinet shutter/ drawers etc fixed with screws, sovent cement, adhesive including dismantling old existing board complete all as specified & directed . Make : RAJSHRI/ ECOCELL/ SINTAX or Equivalent. 64 S&F forcontinuos piano hinges, mild steel bright finishwidth of flap 40mm,fixed as in repair complete all as specified and as directed. 65 S & F75mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plateand fixed with screwsetc complete all as specified and directed. 66 M&L for PVC Lipping 3 to 4 mm thick fixed to 18/19mm board with nails/adhesive complete all as specified and directed. 67 Demolition of RCC jallies/Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately), complete all as specified and directed. 68 Material and labour for providing precast cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in louvres and jallies, 40mm thick (measured solid) set in cement mortar 1:6, complete all as specified and directed. 69 Excavating in post holes in Soft/loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface complete all as specified. 70 M&L for cement concrete(1:2:4) type B-2 (using 40mm graded crushed stone aggregate) asin foundation, filling and mass concrete. 71 S&F M S work as in rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other, connecting plates conforming to Fe-290 Gde E-165 complete all as specified and directed. 72 M&L for Painting on steel surcace exceeding 10cmwidth or girth with two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 73 S&F Pre-painted galvalume aluminium zinc coating (AZ 150 ),GI based corrugated steel sheet 0.50mm thickof an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with selft tapping screws as specified complete all as specified and directed. 74 S&F in 20mm dia Stainless Steel curtain rod withfancy brackets/end brackets/ fennels andfixing stops, rollers etc complete all as specified. 75 S&F in repair of Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified. 76 S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. 77 S&F in repair 110mm dia PVC Rain water pipes single socketed in any length with rubber ring joints fixed to wallscomplete all as specified and directed. 78 S&F in repair 75 mm bore PVCbends of any radius complete all as specified and directed. 79 S&F in repair 110 mm bore PVCbends with accesss door of any radius complete all as specified and directed. 80 S & F PVC (SWR) junction single, (Single T) 110 mm bore equal or unequal complete all as specified and directed. 81 M&L in repair PVC SWRfloor traps 75 mm dia with gratingincluding jointing to wastepipe with run led jointed and setting/fixedin cement concrete type B-1 (1:2:4) complete all as specified and directed. 82 S&F PVC(SWR) gully traps125/110 mm dia setting and jointing with cement solvent complete all as specified and directed. 83 S&F in repair 10 litre capacity PVC valveless, syphonic action type,low level flushing cistern white complete with inlet, ball valve float and handle incl bracket all as specified and directed. 84 S & F in repairs for Vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe) including P or S trapfixed complete all as specified and directed. 85 S&F infor Vitreous china wash down water closet pan with cover, pedestal pattern, white, fixed in repairs complete including connecting to existing cistern including P or S trapfixed complete all as specified and directed. 86 S&F in repairs for Vitreous China table top wash basin, white or ivory colour flat back, size 530mmx420mmx140mm/600x390x150mm/600x380x130mm excluding taps, waste chain and plug and porcelain stopper but including Coupling as per Model complete all as specified and directed. Make : Jaquar , Parryware , Cera 87 S&F for brasschromium plated 40mmbottle traps with wall flange for wash basins/urinal pot with inlet and outlet screwed for pipe or connections includingnecessary packing, union, cap and reducer and fixed. Make : Cera/Hindware/Parryware. 88 Cutting holes into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l exc 150 sqcm and not exc 400 sqcm complete all as specified and directed. 89 S & F GI pipe 50mm dia medium grade laid onfloor/inserted in wall incl all fittings complete all as specified and direced by EIC. 90 Cutting chases, pinning in brick wall,stone or block wall.at any height making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etcand making good, cutting exc 5 cm n ecx 15 cm girth. 91 S & F in repairs for brass chromium plated pillar cock, with extension body, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore. Make : Jaquar , Cera, Parryware 92 S&F in repairs for Chromium plated brass angle valve for 15mm bore pipe, fixed complete all as specified and directed. Make : Cera , Parryware , Hindware 93 S&F in repairs for Chromium plated bib cock with wall flange,Screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as spcified and directed. 94 S&Ffor Tubular towel rail of brass chromium plated, 20mm dia, D type, 60 cm long between flanges, fixed complete all as specified and directed by Engineer-in- Charge. 95 S&F in repairs for PVC connection 15mm dia and 45 cm long with 2 Nos PTMT nuts, fixed complete all as specified and directed. 96 S&Ffor Pop upcoupling of CP (half or full threaded) 32 mm to 45 mm bore fixed complete all as specified and directed. Make : Hindware/ Jaquar/ Parryware. 97 S & F 15mm bore Tubes, `medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorsincluding Taking up or down existing pipe and necessary cutting chasing into wall etc all as specified and as directed. 98 S & F for 20mm bore Tubes, `medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floorsincluding Taking up or down existing pipe and cutting chasing into wall etc all as specified and as directed. 99 S&Fin repair for CPToilet paper holder including all fitting and fixture complete, Make : Cera/ Parryware/ Hindware. 100 S&F in repairof brass chromium plated shower rose, 125mm size with long swivel plush CP arm complete all as specified. 101 S&F in repair ofconcealed stop cock, fancy type 15mm bore, chromium plated complete. 102 S&Fin repair CP Brass mixer 15mm bore dia pipe for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. 103 Supply and fixingHealth faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect and fixed in repair ascomplete all as specified and directed. 104 Supply and fixing 1000 litres capacity rotational moulded polyethylene water storage tanks, white colour (Cylindrical vertical with threaded closed top) Triple layered hoisted and fixed in position, including PTMT tank nipple, float valve of 20 mm bore etc, including dismantling existing water tankcomplete all as specified. 105 Taking down shutter/ steel window of any description n exc 1.5sqm and refixing at same openig after welding,Resecuring ,adjusting or easing to close and opening complete all as specified. 106 M&L for 50mm thick PCC 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in Plinth protection, making even and smooth surface without using extra cementincl dismantling / demolition and rubbish off the primises etc complete all as specified and directed. 107 S & Fin repair for 5.50mm thick 1200 x 750mm mirror of selected quality glass with eadge moulding, mounted on wall fixed with SS stud fixed complete all as specified and directed. 108 S & F factory made 30mm thick Glazed andskeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified inSSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkats 109 M&L for Plain cement concreteType - D2 (1:4:8) (using 40mm graded crushed stone aggregate) asin sub base complete all as specified and as directed. 110 M&L for Rubber moulded coloured (Red, Yellow & Black) precast concrete interlocking paver blocks with grey cement andpigment any shape and size, shade as approved by GE, 80mm thick conforming to IS 15658-2006M-40 grade and interstices filled with sand including 25 mm thick sand cushion complete all as specified and as directed. 111 M & L for Treating soil along the external wall below concrete or masonry apron using chemical emulsion (Chlorophyriphos 20 EC conforming to IS 8944 or Imidacloprid 30.50 SC conforming to IS 16131 (Refer Table 1 on Sl. Page No. 2 of IS 6313 (Part 2) : 2013)) @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed. 112 M & L for Treating the soil under plinth protection at the rate of 5 litres of chemical emulsion (Chlorophyriphos 20 EC conforming to IS 8944 or Imidacloprid 30.50 SC conforming to IS 16131 (Refer Table 1 on Sl. Page No. 2 of IS 6313 (Part 2) : 2013)) per square metre of surface area, complete all as specified and directed. 113 Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.complete including fixtures & fittings (such as ceiling rose, socket, switch , Pendent, regulator, light fitting etc) and removing the materialfrom site and making good the disturbed surfaces of walls ceiling etc complete all as directed. 114 M & L for Concealed Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLSH) cable, multi-stranded, copper conductor, inuniversal colour code with & including suitable size of rigid non-metallic UPVC conduit (not less then 20mm dia med gd) and its all accessories complete concealed in wall / roofincl cutting & chases and modular flush metal boxes 0.8 mm thick( Same as Switches Make) suitable for modular fittings including modular outercover mirror/Glass finish plate with inner mountingframe of make Legrand (Arteor)/Schneider (Zencelo) /Anchor (panasonic Thea) /Goldmedal (Nexon Quorra) as per site requirementfor mounting modular switches, socketsetcincluding earth wire ofPVC insulated (FRLSH) copper conductor multistrandedof 1.5Sqmmsize in green colour including making good(i.e plastering ,one coat of putti and two coats of interior emulsionpaint with matching existing surface ) forOne light point/exhaust/ceiling fan controlled by one way switch 6 amp complete all as specified 115 All as perSrl item no 113 here-in-before but One 3 pin 6 Amps socket point controlled by one Modular switch on same board. 116 All as perSrl item no 113 here-in-before butOne 3 pin 6 Amps socket point controlled by one Modular switch on independent board. 117 All as per item No.113 here-in-before butfor 3 pin / 5 pin 16 Amps sockets outlet with 2.5 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent and 2.5Sqmm PVC insulated & unsheathed (FRLS) copper conductor earth cable complete all as specified and as directed. 118 Supply and FixingModular switch16/20 Amp single pole one way,2Module with indicator and no top gap between rocker plate and fully shrouded double rocker mechanisam type all the importent parameters like rating etc should be laser printed on every switch along with catoulage numberall as specified. Make : Legrand (Arteor)/Schneider (Zencelo) /Anchor (Panasonic Thea) /Goldmedal (Nexon ) 119 Supply and Fixingmodular socket shutter type,2-in-1,3 and5 pins 6 /16 Amps, combined 2 Module and no top gap between rocker plate and fully shrouded double rocker mechanism type all the important parameters like rating etc should be laser printed on every switch along with catalogue numbercomplete all as specified. Make : Legrand (Arteor)/Schneider (Zencelo) /Anchor (Panasonic Thea) /Goldmedal (Nexon ) 120 Supply and FixingModular ceiling rose surface bakelite Square in shape 100 mm x 100 mm, three terminals complete all as specified.Make - Goldmedal (Glassio) or equivalent in Anchor/Cera. 121 Supply and FixingModular switch 6 Amps single pole one-way, 1 Module and no top gap between rocker plate and fully shrouded double rocker mechanism type all the important parameters like rating etc should be laser printed on every switch along with catalogue numbercomplete all as specified. Make : Legrand (Arteor)/Schneider (Zencelo) /Anchor (Panasonic Thea) / Goldmedal (Nexon ) 122 Supply and Fixing Modular socket shutter type, 2-in-1, 3 pins 6 Amps ,ISI marked, combined 2 Module and no top gap between rocker plate and fully shrouded double rocker mechanisam type all the importent parameters like rating etc should be laser printed on every switch along with catoulage number complete all as specified. Make : Legrand (Arteor)/Schneider (Zencelo) /Anchor (Panasonic Thea) /Goldmedal (Nexon ) 123 Supply & FixingModular fan Regulator electronic, 8 step type 100 watt , ISI marked, 2 Module complete all as specified. Make : Legrand (Arteor)/Schneider (Zencelo) /Anchor (Panasonic Thea) /Goldmedal (Nexon ) 124 Supply and fixingpicture lights light type LED, 200-240 Volts, Muziris Picture Light - 12W, 19.6L x 7.1W x 3.7H Centimeters, lighting method Downward bulb base E27, warm/cool/natural as per site requirement , wall mountwith all accessoriescomplete connections all as specified and directed.Make :- Philips/ Jaquar/ Havells. 125 Supply and fixingdecorative ultra slim surface /Wall mounted T5/decorativeLEDbatten light complete fitting 1x 10 watt LEDsuitable for mirror light with polycarbonate channel housing & integrated electronic driver, energy efficient, warm/cool/natural as per site requirement, 140V-270 volts, including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified. 126 Supply and fixingindoor decorative ultra slim surface /Wall mounted T5 LEDbatten tube light complete fitting 1x 20 watt LED Tube fitting with aluminium channel housing & integrated electronic driver, energy efficient, 140V-270 volts, Warm/natural/cool as per site requirement type>110 Lm/Wattcomplete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified. 127 Supply and fixing of 02 feet10 Watt LED Batten with extruded aluminimum housing with high quality PC diffuser warm/cool/natural as per site requirement, complete all as specified and directed by Engr-in-Charge. 128 Supply and fixingof energy saving LED Street light of 60 Watt Capacity high pressure die cast alumininum housing with seal toughned glass cover, minimum 125 lumen/watt, cool/warm as per site requirement, operating voltage range 120 -220 Volts IP-66 surge protection including suitable GI bracket for fixing street light complete all as specifieid and directed. 129 Supply and fixing ceiling fans copper winding, complete with aluminiumblades, down rods,suitable forelectronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 215 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC )complete all as specified and directed by Engineer-in-Charge.Make : Havells/ Goldmedal/ Bajaj/ Orient. 130 Supply and fix in repair ofExhaust fan 380mm sweep, copper winding, 1900 CMH, 90 W, 4 blades with aerodynamic design, Mettallic type alongwith GIlouvers complete suitable to work on AC, single phase, 230 Volts, 1400 RPM, 50 Hzincluding connecting up with three core twisted flexible copper conductor cable of suitable size 0.75 Sqmm all as specified and directed.Make : CG/ Havells/ V Guard/ Gold Medal/ Bajaj. 131 Material and labour in replacement of Sub Main Wiring with two run single core 6.0 Sqmm (nominal area) multi stranded copper conductor FRLS PVC insulated and unsheathed 1100 volts grade colour code cables, drawn on surfacein and including UPVC conduit of 25mm dia bore medium grade, including standard fittings such as Tees, junction, bends etc., with and including one run of continuous multi stranded copper conductor 6 Sqmm (nominal area) FRLS PVC insulated and unsheathed 1100 volts grade colour code cable for earth continuity and including making good (i.e plastering ,one coat of putti and two coats of interior emulsionpaint with matching existing surface) including taking down old, complete all as specified and directed.Note :- Two run of 6 Sqmm + One run of 6 Sqmm for earth wire + one run of UPVC conduit of 25mm dia shall be measured as one RM. 132 All as per item No 130 here-in-before but for 2 X 2.5 Sqmm + 1 X 2.5 Sqmm cable 133 Supply and fixing in replacement of Distribution board, double doorTPN 4 way,vertical typewith MCCB TPN as incomerwith 160 Amp rated bus bar IP 43 protection, cement spill protector, door earthing including MCCB TPN 100 Amp 16 KA as incomer -01 Nos complete all as specified and directed. Make : Goldmedal/ Legrand/ Havells. 134 Supply and fixingin replacementof MCB DB Single pole and neutral08 way, double door, sheet steel phospehtised powder painted withIP 43 protection 240 V neutral link, earth bar and Din rail complete all as specified and directed.Make : Goldmedal/ Legand/ Havells. 135 Supply and fixingArc Fault Detection Device (AFDD) with RCBO 32 Amp combined SPN MCB + AFDD + RCCB, offering protections for overload, short circuit, reidual current characteristices type A, over voltage protection above 270V AC +/- 5% & series, parallel arc fault, AFDD must be with dual test button for AFDD and earth leakage functions along with single diagnostic LED with blinking patterns for continious ON series arc parallel arc & over voltage protections.Make : Havells/Goldmedal/ Legand or equivalent 136 Supply &Fixingin replacementSP MCB 240 volt 5 to 32Amps,C curve, with suitable size lug thimbles integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly, with efficient air chanels etc complete all as specified. Make : Legrand/ Goldmedal/ Havells. 137 Supply and fixing in replacement FRLS PVC insulated copper conductor of Size 4 Sqmm 3 core with cable thimble as required for bollards/Lt panels etc with necessary connections including UPVCconduit Heavy grade 25 mmComplete all as specified and directed. Note :- UPVC conduit along with PVC copper cable to burried in ground at a depth of 20 cm. Cost of excavation to be included in the quoted rate. 138 Supply and fixing in replacement bollard fitting 10W, neutral white, 3000 CCT, UFO Shape design, IP 65 protection including25mmUPVC conduit for passing electric cable and100mm length fastners for fixing bollard, PCC 1:2:4 (12.5 mm graded crushed stone aggregate) of size 30 Cm X 30 Cm x 45 Cm (30cm above GL & 15cm below GL) any shape or size as required including applying exteriorcementpaint over cement exposed surface, necessary formwork and excavation, removing debris outdside MoD land exc 1.5km and nexc 3km all as specified and directed.Make : Jaquar (cat part No. OBL GRY LBLDDSC010XW)/ Havells (Cat part No UFOBLS10WLED830PSYMTOPC) orequivalent in Phillips. 139 Supply and fixingin replacement of LED flood light 100 watt 230 V AC with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. Make :- Philips/ Jaquar/ Havells. 140 Supply and fixingin replacementof LED decorative post top light fitting 40 watt,Neutral white ,3000 CCTdesigned spun aluminium and high grade aluminium heat sink for efficient thermal management, sturdiness and excellent corrosion resistance with MS base, IP 66 protection having glare free and better uniformity light distribution complete all as specified and directed. Make :- Philips/ Jaquar/ Havells. 141 Supply and Fixingin replacement of Modular switch 20 Amp single pole one way, 2 Module with indicator and water heater marking by using new concealed sunken pressed steel terminal boxes 0.8 mm thick (Same as per Switch Make) with inner mounting frame and outer Mirror/glass finish cover plate 2 Module of suitable size for mounting of modular switches, sockets, fan regulators etc fastened with chromium plated screws including making good (i.e plastering, one coat of putti and two coats of interior emulsionpaint with matching existing surface) complete all as specified and directed. Make - Goldmedal (Nixon Quorra)/ Legrand (Arteor)/ Anchor (Panasonic Thea)/ Schneider (Zencelo). 142 Supply and fixingin replacementof MCB protected modular socket with Modular MCB 16 Ampsbuilt in Modular MCB + Modular Socket 16 Amps+PRCD Top 3 Pin, 16 Amps 30 mAwith concealed metal sheetsteel enclosure 0.8 mm thick (Same as per Socket Make) with inner mountingframe and outer Mirror/glass finish modular cover 3 Modulefor mounting including making good (i.e plastering, one coat of putti and two coats of interior emulsionpaint with matching existing surface) complete all as specified and directed. Make - Goldmedal (Nixon Quorra)/ Legrand (Arteor)/ Anchor (Panasonic Thea)/ Schneider (Zencelo). 143 Supply and fixingwater storage heater vertical (geyser) with inner Tank Material :TitaniumGlass Lined coated Tank - 2X Corrosion Resistance, Outer Body Material : ABS, Type : Storage, Capacity : 25 Litres, AC 220-240 Volts, Wattage : 2000 Watts, with preset thermal cutout, Pressure : 8 Bars, BEE Rating : 5 Star, Multifunction 4 in 1 safety valve, glass coated heating element, adjustable temperature control knob, Magnesium anode rod, install on wall by anchor fastnerscomplete with three core twisted flexible copper conductor cable of suitable size upto 2 metre all as specified and directed. Make - Gold Medal (Hydro)/ Havells (Magnetron)/ Jaguar(Elena).
