|
| 1 | Dismantling of brick work or stone/boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles complete all as specified and as directed |
| 2 | Demolition of cement concrete, un-reinforced in ground floors and paving not exceeding 15 centimetre thickness, below or above ground level complete all as specified and as directed. |
| 3 | Demolition of cement concrete, (reinforced)of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)complete all as specified and as directed. |
| 4 | Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar, in 150mm internal dia complete all as specified and as directed. |
| 5 | All as per Serial Item No 4.00 here in above but 100 mm bore -ditto-. |
| 6 | Takingout cement plaster, any description, from brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed |
| 7 | Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed |
| 8 | Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and as directed. |
| 9 | Removing excavated surplus soil/material not exceeding 50mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed |
| 10 | M&L for Salt Glazed Stone Ware drain pipe, grade ‘A’ 100 mm bore laid in trenches and jointed complete all as specified and as directed. (Excavation and earth work shall be measured and paid separately). |
| 11 | All as per Serial Item No 10.00 here-in-above but 150mm bore pipe all as specified and directed. |
| 12 | M&L for 100 mm thick Concrete bed to drain pipes in cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 100 mm bore pipe complete all as specified and as directed |
| 13 | All as per Serial Item No 12.00here- in-after above but for 150 mm bore pipe complete all as specified and as directed. |
| 14 | M&L for Plain Cement concrete type D-2 1:4:8 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed. |
| 15 | M&L for Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, draincomplete all as specified and as directed. |
| 16 | M & L for forming fair finished channel not exc 40cm girth using extra cement complete all as specified and as directed. |
| 17 | M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 complete all as specified and as directed. |
| 18 | M&L rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with WPC as per manufacturer\"s instruction and finished the surfaces even and smooth without using extra cement complete all as specified and as directed Note : WPC will be measured and paid for separately. |
| 19 | M&L for 15mm thick rendering in cement mortar (1:6) on brick/concrete surfaces of walls, finished even & smooth surfaces without using extra cement complete all as specified. |
| 20 | Supply only integral water proofing compound as per latest IS specification complete all as specified. |
| 21 | M&Lfor preparation of new plastered surfaces of walls and applying two coatsof cement base paint complete all as specified and as directed. |
| 22 | M&L for preparing of new plastered/ concrete surfaces of wall etc and applying two coats ofoil bound distempers including a coat of primer with alkali resistant primer complete all as spicified and directed. |
| 23 | M&L for Pre-cast cement concrete cover slab for manhole and drain coverin plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4with plain faces including necessary formwork complete all as specified and as directed |
| 24 | M&L for TMT Bars 6 to 8mm dia cut to length bent to shape reqiured, incl cranking, bending spirraly for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9m dia or securing with clips. |
| 25 | M&L for Cutting into existing manhole for inserting 100 mm bore pipe, for new drains making good to pipe and cutting out existing benching and forming branch channel in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates, smooth finished and re-forming benching complete all as specified and as directed |
| 26 | All as per Srl Item No 25.00 here-in above but for 150 mm bore pipe |
| 27 | Cleaning of Sewage lines 100 mm bore pipe and removing the blockageby pressure pump completely excludingconnected manhole with and includingbamboo splits/flexible iron wire or concrete malacces rods from manhole to manhole, through pipes fromtrap to manhole, rendering the system clearand flushing the delogged line with sufficient quantity of water and removing sludge/waste material etc. to a distance not exc 50 mtr and burrying in pits complete all as specified and directed by the Engr-in-Charge.Note : The cost for excavation and earth work for pits is deemed to be included in the unit rate. |
| 28 | All as per Serial Item No 27.00 here in above but line of 150mm bore pipe. |
| 29 | Supply and fixing in repair SWG gully traps square type size (150x100)mmcomplete all as specified and directed.. |
| 30 | Cleaning manhole by taking out sludge in semiliquid/solid stage (incl. all water etc) from inside of manhole of depth not exceeding 1.5 m and removing the sludge to a distance not exceeding 50m depositing in trenches including supply and sprinkling bleachingpowder and covering sludge with earth to a thickness not less than 30 cm including all earth work, returning filling, removal of surplus soil & necessary temporary cleaning as directed by the Engineer-in-Charge. |
| 31 | All as per item 30.00here-in-beforebutdepth exceeding 1.5mtr but not exc 3mtr. |
| 32 | Dewatering & Desludging of septic tank of 100 users including working in foul position incl sprinkling to bleaching powder on internal wall surface and upto 50cm wide from end of wall around & top of slab of septic tank and removal of sludge / liquid mud or any other obstruction material and deposting out of MOD land with help of covered container and burried in pit & covered with 15cm layer of soil complete all as specified and as directed by Engr-in-Chargr. Note : The cost for excavation and earth work for borrow pits for burrying sludge/waste material shall deemed to be included in the unit rate of this item. |
| 33 | All as per item 32.00 here in before but for cleaning of septic tank 50users up to any depth.complete all as directed by Engineer-in-Charge. |
| 34 | All as per item 32.00 here in before but for cleaning of septic tank 25users up to any depth.complete all as directed by Engineer-in-Charge. |
| 35 | Cleaning of septic tank of 200 users capacity in running /flowing order without disturbance for removal of all blockages by any mechanical device system and making fully functional at any location in the area covered by AF Station, Site \"C\", 3AFSR, NKP and MES area complete all as specified and as directed by Eungineer-In- Charge. Note : The following elements are included in the unit rate of this item- (a) Working in foul conditions/ positions. (b) Making good the the disturbed position of any during the cleaning. (c) Removing sludge/ waste material/ liquid/ mud/dirt/silt or other obstruction taking out through covered contain/ tanker to a distance exc 5Km and disposal off out of MOD land or as directed by Engr- In- Charge. |
| 36 | M&L for cleaning of soak well by pumping out or any other suitable means of dia of soak well exceeding 2.50 mtr and not exc 3.00 mtr and depth not exc 3.00 mtr complete all as directed by Engr-in-Charge. |
| 37 | Cleaning to blocked floor/nahani trap and CI/PVC pipe upto 1st manhole and removing all silt residue sludge both organic and inorganic nature including any type of foreign materials and removing wastematerial /sludge etc to a distance exc 50 mtr and disposal out of MOD land as directed by Engr-in-charge and sealing the sides of traps in bathroom/ kitchen using Aqua TS of Aqua shield water proofing or equivalent chemical and making good the disturbed floor of any during the cleaning to entire satisfaction of Engr-in-charge complete all as specified and as directed. |
| 38 | Cleaning to blocked WC trap and CI/PVC pipe upto 1st manhole and removing all silt, residue sludge both organic and inorganic nature including any type of foreign materials and removing wastematerial /sludge etc to a distance exc 50 mtr and disposal of out of MOD land as directed by Engr-in-charge and sealing the sides of traps using Aqua TS of Aqua shield water proofing or equivalent chemical and making good the disturbed floor of any during the cleaning to entire satisfaction of Engr-in-charge complete all as specified and as directed |
| 39 | S&F in repair 110mm PVC (SWR) dia pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-charge. |
| 40 | S&F in repair75mm PVC (SWR) dia pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-charge. |
| 41 | S&F in repair 75mm bore PVC (SWR) bends any radius with access door as in repaircomplete all as specified and as directed by Engineer-in-Charge. |
| 42 | S&F in repair 110mm bore PVC (SWR) bends any radius with access door complete all as directed |
| 43 | S&F in repair110mm bore PVC (SWR) branch piece, double (double \"Y\") equal or unequal with access door complete all as directed |
| 44 | S&F in repair 110mm bore PVC (SWR) junction double (double T) equal or unequal with access door complete all as directed |
| 45 | S&F as in repair for 75 mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specied and directed by Engr-In-Charge. |
| 46 | S&F as in repair for 100 mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specified and directed by Engr-In-Charge. |
| 47 | S&F in repair Vitreous china squatting pan \"Orissa\" pattern \" size 580x440mm white, with integral foot rest \"P\" or \"S\" trap,front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, etc. Complete making good to floor as existing complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F in repair Vitreous china wash hand basin, white flat back of size 550x400mm including bracket, cutting for pinning in ends of brackets or erecting stands including brass chromium plated waste coupling 32mm dia, PVC waste pipe adequate length and dia and PVC connection 15mm size 450mm length with brass CP nuts on both sides, PVC washers, fixed in repairs all as specified. |
| 49 | S&F in repair Pillar taps,15mm dia fancy type with capstan heads,chromium plated screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 50 | S&F in repair PVC low level flushing cistern 10 ltrs capacity white with inlet, ball valve, float valve and handle incl brackets, PVCflush pipe ,PVC connection, complete all as specified and directed . |
| 51 | S&F in repair vitreous china wash down water closet pan (pedestal pattern) whitewith ‘P’ or ‘S’ trap plastic seat cover white including connection to out going pipe & toflushing pipe, anti-syphonage pipe etc as in repairs (excluding flushing cistern) complete all as specified and directed by Engineer-in-charge. |
| 52 | S&F in repair Stop valves,cast copper alloy 15 mm dia fancy type, chromium plated screwed down, high pressure screwed both ends for iron pipe or for unions all as specified. |
| 53 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises. |
| 54 | M&L for Non skid ceramic coloured designer joint free tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4complete all as specified and directed. |
| 55 | M&L for glazed ceramic coloured tilesin vertical surfaces 350x250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement ot match, over a backing coat 10mm thick in CM (1:4) all as specified and as directed. |
| 56 | M&L for Cutting of saplings of any size from bulidings in any situation & at any height including removal of roots from roof/wall including applying root killer chemical as per manufacturers instructions and making good disturbed portion with PCC 1:2:4 Type B0 (using 12.5mm graded stone aggregate) complete finish with cement mortar (1:4) as specified and as directed. |
| 57 | S&F in repair Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms) complete all as specified and as directed. |
| 58 | S&F in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms)complete all as specified and as directed. |
| 59 | S&F in repairs PVC connection 15 mm dia 600mmm long with 2 Nos PVC check nuts with washer complete all as specified and directed. |
| 60 | S&F in repair 32mm dia PVC waste pipe for WHB & kitchen sink 80cm long with union complete all as specified and directed. |
| 61 | M&L for 10 mm thick rendering on ceilings in cement mortar 1:4 and finishing the surface even and smooth without using extra cement complete all as specified. |
| 62 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper (OBD) of approved shade/tint over and including one coat of alkali resistant primer complete all as specified and as directed. |
| 63 | M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed. |
| 64 | M&L for preparation of newly plaster surfaces andappplying two coats of cement base paint overprimer coats of alkali resistance priming paintcomplete all as specified and directed. |
| 65 | M&L for complete removal surface finishes of walls, external fins, fascia, vertical and horizontal surface of roof projection, chajja etc including brooming down complete all as specified and as directed. |
| 66 | M&L for applying two coats of weather proof anti fungal exterior acrylic emulsion paint (smooth classic) over a coat of primer on old plastered surface of wall, external fins, fascia, vertical and horizontal surface of roof projection, chajja etc including necessary scafolding and other necessary safety measures required (such as safety belt and safety rope, helmet etc for labour) during execution of work complete all as specified and as directed. |
| 67 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded, pointed in any mortar complete all as specified and as directed. |
| 68 | M&L for factory made 60mm thick machine pressed precast cement concrete coloured, rouber moulded, designer (reflecting type) interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directedwith grey cement and pigment with coloured top laid over andincluding 50mm thick sand cushioning, joints of blocks filled with dry sand complete all as specified and as directed. Note : Sand shall be measured and paid separetely here-in-after. |
| 69 | M&L for Sand filling under floors or in foundations including wateringand consolidation complete all as specified and as directed |
| 70 | Dismantling floor, hearth or wall tiling including cementmortar bedding (but not backing), removing serviceabletiles to store and rubbish off the premises complete all as specified and as directed |
| 71 | M&L for pre-polished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set jointed and pointed in neat cement slurry in floor with white cement and pigment to match over and including 15mm thick screed bed or bedding layer of CM 1:6 complete all as specified and as directed |
| 72 | Demolition of cement concrete (unreinforced) in ground floor paving not exc 15cm thick (below or above ground level) |
| 73 | M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in hardstanding, plinth protection etc finished the surface even and fair without using extra cement complete all as specified and as directed |
| 74 | M&L for 40 mm thick, Cement concrete, type B-1, (1:2:4), 20 mm graded aggregate as in floor making finished even and smooth using extra cement. |
| 75 | Dismantling of chain link fencing wire mesh any type and position and removing from site complete all as specified and as directed |
| 76 | Supply only chain link MS galvanised fencing, any size or type complete all as specified and as directed. |
| 77 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire as in repair complete all as specified and as directed |
| 78 | Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for. |
| 79 | M&L for Mild steel round bars 6 to 8mm dia conforming to Fe-290, Gde-E-165 for fixing chain link wire mesh etc. complete all as specified and as directed by Engr-in-charge |
| 80 | S&F for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of tandard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed |
| 81 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground post embeded in natural ground and removing from site complete all as specified and as directed |
| 82 | All as per item No 81.00 here-in-before but posts embedded in concrete, brickwork and masonry and removing from site |
| 83 | Excavating in post holes (or similar holes) each not exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exc 50 mtr and making good surfacecomplete in soft/loose soil all as specified and as directed |
| 84 | M&L for PCC (1:3:6)type C1 (using 20mm graded stone aggregate) for fixing angle iron posts etc all asspecified and as directed |
| 85 | S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, balusters, nosing to steps, including embeding in concrete and screwing etc wind ties for roof including securing bolts posts and struts in fencing, also posts and struts in swan neck angle including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling , bolting or riveting etc and similar work to conforming Fe.290.Gde-E-165complete all as specified and as direccted. |
| 86 | M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut (dia of neck 10 mm and 10 cm long) complete all as specified and as directed. |
| 87 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete. |
| 88 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPs as in roof covering/cladding to wall, fixed with self tapping screws. |
| 89 | S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet for Ridges of 0.50mm thick of an colour having tensile strength of 550 MPs as in roof covering/cladding to wall, fixed with self tapping screws. |
| 90 | S&F steel work asin tubular trusses including special shaped washer etc completeusing ERW or induction butt welded tubes confirming to IS 1161-1979 grade St 240 complete all specified and directed. |
| 91 | M&L for preparation of new steel and iron surfaces of any description not other wise described over 10 centimetre width or girth and applying two coats of synthetic enamel paintover a coat ofred oxide primer complete all as specified and as directed. |
| 92 | Supply & fixing concertina coil heavy duty (reinforced punched barbed tape single layer) fixed on Y shape angle iron complete all as specified and as directed. (i) Dia of concertina coil 600 mm dia (ii) Nos of turns in concertina 50 to 53 turns (iii) Coverage per coil 6RM |
| 93 | M&L for Granite (of any type) tiles 18-20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing completeover 15mm thick screed bed in CM 1:6 over platformcomplete all as specified and directed. |
| 94 | M&L for 18-20 mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over a backing coat 10mm thick in CM (1:3)complete all as specified and directed. |
