Tender For Comprehensive Maintenance Including Periodical Services To 225 Asc (Sup) Under Ge (C) Kolkata; 1.00 Demolition Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc, but excluding Ashlar Facings, dressed Stone Work and Pre-cast Concrete Articles of any descriptions, complete all as specified and as directed. 2.00 Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed 3.00 Taking down of shutters of any description nexc 1.0 Sqm each complete all as specified and directed 4.00 Taking down shutters of any description exc. 1.00 Sqm but n.exc 2 Sqm each and removing from site or to store as directed by Engineer in charge. 5.00 Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm complete all as specified and directed. 6.00 Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed. 7.00 Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water, remove dust, debris/ rubbish, etc., complete all as specified and as directed. 8.00 Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed. 9.00 Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in mortar complete all as specified and directed. 10.00 Dismantling wrought iron or mild steel work viz steel window, ventilator, guard bars etc of any description not otherwise provided for complete all as specified and directed. 11.00 Dismantling Plain or Corrugated Steel Sheeting any gauge, thickness, including nainital or similar roof coverings/sunshade, complete all as specified and as directed. 12.00 Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed. 13.00 Dismantling Timber Fillets, Rails, Posts, Rafters, Purlings, etc., under 40 Sqcm in Section, in any Position, as in unframed Work, complete all as specified and as directed. 14.00 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 15.00 M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed. 16.00 M&L Brick work with fly ash bricks designation 75 (kgf/cm2) straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed. 17.00 M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed. 18.00 Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of laddings, steps, cills, sushades, shelves, lintels etc and cutting chase for concealed water tubing or concealed coduit wiring etc and making good cutting grith n exc 10 cm girth on brick walls complete all as specified and directed. 19.00 M&L Second Class Hardwood in Scantlings wrought Timber Framed and fixed complete all as specified and as directed. 20.00 M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section wrought, secured with Nails, cross sectional area exc 6.0 Sqcm but not exc. 13.0 Sqcm, complete all as specified and as directed. 21.00 M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section Wrought, secured with Nails, cross sectional area exc13.0 Sqcm but not exc. 25.0 Sqcm, complete all as specified and as directed. 22.00 S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed. 23.00 S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed. 24.00 S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification complete all as specified and as directed. 25.00 S&F Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5 mm thick PVC sheet fillet of width 35mm for wall Paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing including taking down old unserviceable PVC wall lining complete all as specified and as directed. 26.00 S&F Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints, complete all as specified and as directed. 27.00 S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed. 28.00 S&F for 2nd class hardwood 30mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or roun-ded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed. 29.00 M&L Second Class Hardwood 35mm thick Plain Framed Panelled Door Shutter (any Number of Panels) with Panel of 12mm thick BWP Commercial Ply or Veneered Particle Board with commercial face veneers on both faces and fitted to Wooden Chowkat, complete all as specified and as directed. 30.00 M&L Second Class Hardwood 30mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and as directed. 31.00 S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkhats complete all as specified and directed. 32.00 S&F Mild Steel Butt Hinges, size of Hinges 75mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed 33.00 S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed 34.00 S&F Stainless Steel Butt Hinges size of Hinges 100 mm (medium weight) and fixed, complete all as specified and as directed 35.00 S&F Aluminium anodised, barrel tower bolts of extruded section, 100 mm long and fixed with steel screws complete all as specified and directed. 36.00 S&F Aluminium anodised, barrel tower bolts of extruded section, 150 mm long and fixed with steel screws complete all as specified and directed. 37.00 S&F Aluminum alloy Handle 100mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed. 38.00 S&F Aluminum alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed. 39.00 S&F 250 mm long Aluminum alloy, anodized, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminum alloy and fixed, complete all as specified and as directed. 40.00 S&F Aluminium body(extruded section) door closer hydraulically regulated, designation No 2, universal type suitable for door shutters of 701 to 850 mm in width and weight between 61 to 80 kg and fixed as in repair complete all as specified and as directed. 41.00 S&F Floor door stopper of steel body and overall length of cover plate 150 mm and tongue anodised with hard drawn steel spring as in repair complete all as specified and directed. 42.00 S&F Double action floor spring hydraulically regulated, made up of minimum 1.25mm thick aluminiun alloy sheet foundation box, main body with stainless steel cover ,governing piovet made of brass ,other parts made of mild steel heavy duty and fixed complete all as specified and as directed. 43.00 S&F 20 mm dia Fancy type, Chromium Plated colour coated ( any coloured) curtain rod fixed to bracket/ pelmet box complete all as specified and as directed. 44.00 S&F Chromium plated Bracket for curtain rod in any size complete all as specified and as directed. 45.00 M&L Mild Steel Work in Tubular /hollow section as trusses, purlin , rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade YSt.-240 complete all as specified and as directed. 46.00 S&F Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. and similar work complete all as specified and directed. 47.00 S&F Mild Steel as in Holdfast Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed. 48.00 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, etc fixed with self tapping screws etc; complete all as specified and as directed. 49.00 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screw complete all as specified and directed. 50.00 M&L for Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.Note:- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate 51.00 S&F in repair Steel rolling shutters 1.0mm thick, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer;erected in position as indicated push pull or manual type etc as in repair complete all as specified and as directed. 52.00 M&L False ceiling with E board Classic , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/tiles with aluminium anodised main T section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 6mm dia GI hooks and clamp and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces as in repair complete all as specified and as directed. 53.00 M&L Powder coated aluminium 50 micron anodised partition consist of single groove rectangular section 101.60 x 44.45 x 1.60mm (Section of jindal wt @ 1.301 kg/rm) and double groove rectangular section 101.60 x 44.45 x 1.50mm (Section No 20028 of jindal wt @ 1.301 Kg/rm) including jointing cleats and glazing clips for fixing builder hardware fittings and half portion covered with 5.5 mmthick selected quality frosted or plain glass balance portion covered with 4mm thick ACP sheet including necessary fittings/fixture/aluminium snap beads, sleats etc complete all as specified and directed. 54.00 S&F Aluminium door with powder coated anodized aluminium frame of section size 101.60 mm x 44.75 mm x 2.4 mm (jindal section 14021) thick, with shutter of style member size of 85mm x 44.45 x 2.00mm thick (Jindal section 19560), Top/bottom rail of member size 114.30mm x 44.45 x 2.15mm (Jindal section 19574) and lock rail of member size 100mm x 44.45mm x 2.0mm thick (jindal section 19564) with rubber gasket and aluminium glazing clip beading and 100mm mortice locking arrangement ,handle, tower bolt 200mm long per shutter, rollers, etc complete all as specified and directed. 55.00 S&F Aluminium anodised Three track sliding window frame with shutters including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements etc. complete including glazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter as in repair complete all as specfied and directed as under :-(A) Sections for frame (i) Top and verticals 92x 29.50 x 1.30 mm thick (ii) Bottom 92 x 29.50 x 1.20 mm thick. (B) Sections for shutter (i) A section 39 x 20 x 1.50 mm thick (ii) Interlock section 39 x 20 x 1.50 mm thick(iii) H section 41 x 20 x 1.10 mm thick 56.00 S&F Aluminium ventilator with powder coated anodized aluminium frame of section size 65.5 x 38.10 x 1.5 mm and Shutter with section 47.62mm x 44.5mm x 1.5mm thick half portion fixed with glass and half portion louvered including powder coated alunimium anodised “D” handle, hinges, peg stays, tower bolt etc including jointing cleats for fixing Builder hardware complete all as specified & directed. 57.00 Stripping of old tarfelt including layer of plaster or morter of any type treatement carefully from roof surfaces (without damage of roof) and roughening of surface of old concrete roofing by picking sweeping cleaning and washing down with water to remove dust as directed and specified. 58.00 Materials and labour for 20 mm thick screed bed of bedding layer in CM 1:4 surface finished even and smooth without using extra cement for padding including neat cement slurry @ 3.0 kg per Sqm complete all as specified and directed. 59.00 M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturers instructions, complete all as specified and as directed :-(a) Preparing and cleaning of fully dry surface as per IS:3067-1966.(b) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.40 Litre per Sqm.(c) Applying a layer of APP based Polymeric Membrance; 3.0mm thick (minimum) weighing 3.00 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. 60.00 M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed. 61.00 M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed. 62.00 M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed. 63.00 M&L Coloured /digital vitrified ceramic floor tiles 8-9 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc. 0.36 sqm (600mm x 600mm x 10mm) as in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 20mm thick screed bed in cement sand mortar (1:6) complete all as specified and as directed. 64.00 M&L Coloured /digital vitrified ceramic floor tiles 8-9 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc. 0.36 sqm (600mm x 600mm x 10mm) on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed. 65.00 M&L glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed. 66.00 S&F Machine cut kota stone slab flooring 20-25mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set Pillar and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles including rubbing and polishing complete over 20mm thick 1:4 cement mortar screed bed complete all as specified and as directed. 67.00 M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, including demolition of old tiles/surface complete all as specified and as directed. 68.00 M&L Pre polished Chequered cement concrete tiles of size 300mm x300mm x25mm thick, with grey cement and no pigment, jointed in neat cemnt slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 including taking out old unserviceable chequered tiles complete all as specified and as directed. 69.00 Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed 70.00 M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directedNote:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate. 71.00 M&L Cement Concrete type B1(1:2:4) (20mm graded crushed stone aggregate) 40 mm thick as in Floor, finishing Concrete Surfaces Even and smooth without using Extra Cement, complete all as specified and as directed. 72.00 M&L Cement Concrete type B1(1:2:4) (20mm graded aggregate) 25mm thick, as in sub base by maintaining required gradient/ undulation, finishing concrete surfaces fair and fair to receive the topping layer, complete all as specified and as directed. 73.00 M&L for 5 mm thick rendering on brick or concrete surfaces of wall in CM 1:3 and finished even and smooth without using extra cement complete all as specified & directed. 74.00 M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and smooth without using Extra Cement complete all as specified and as directed. 75.00 M&L Rendering 15mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 5 mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and fair without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately) 76.00 Supply only liquid water proofing compound (ISI marked) complete all as specified and directed. 77.00 M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of white wash complete all as specified and as directed. 78.00 M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of white wash complete all as specified and as directed. 79.00 M&L Preparing new Surfaces of Ceilng and applying Three Coats of White Wash, complete all as specified and as directed. 80.00 M&L Preparing old decorated Plaster Surfaces of ceiling and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed. 81.00 Material and labour for preparation of existing old wall surface and applying one coat of oil bound distemper (any colour/tint) on wall surfaces complete all as specified and directed. 82.00 M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 2 mm thick wall care putty on ceiling surfaces including rubbing with emmery paper to make surface smooth and even complete all as specified and directed. 83.00 M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 2 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. 84.00 M&L for complete removal of existing finishes and treating with two coats of oil bound distemper (any colour/tint) over a coat of Chalk whiting, over 2 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as directed and specified. 85.00 M&L for preparation of old plastered surface and applying one coats of weather proof exterior emulsion paint over a coat of primer with approved colour and pattern complete all as directed and specified 86.00 M&L Preparing new plaster surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed. 87.00 M&L for complete removal of existing finishes and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed. 88.00 M&L Preparing new Surfaces of Walls upto 4th storey and applying Two Coats of Cement Base Paint over a coat of primer includning necessary scaffolding and safety measures complete all as specified and as directed. 89.00 M&L Complete removal of old decorated surfaces and Finishing and applying Two Coats of Cement Based Paint over a coat of alkali resistant primer complete all as specified and as directed. 90.00 Material and labour for preparation of existing old wall surface applying one coats of cement based paint on walls surfaces complete all as specified and directed. 91.00 S&F Sheet Glass 4.0mm thick ordinary quality glazing with Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed. 92.00 S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 93.00 S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 94.00 M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed. 95.00 M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed. 96.00 M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed. 97.00 M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel plaint over a coat of red oxide all as specified and directed by Engineer-in-Charge. 98.00 M&L Preparing old Wooden Surfaces of any description not otherwise decribed n. exc 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed. 99.00 M&L for PreparatioM&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed. 100.00 Supply and Laying Steel Water Tubing 15mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, including taking down old unserviceable tubes and deposit to store complete as all specified and as directed. 101.00 Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, including taking down old unserviceable tubes and deposit to store complete as all specified and as directed. 102.00 M&L for taking down and refixing of old Steel Water Tubing 15mm Bore (dia), and connections with all new Fittings such as bends, elbows, tees, short pieces, connectors, back nut, reducer, diminishing pieces, caps, unions and plugs etc but except Steel tube connection, in new or old position such as fixed on Walls, Ceiling or laid in Floors or any other Situation, cleaning the same or deposit to store complete as all specified and as directed. 103.00 M&L for taking down and refixing of old Steel Water Tubing 20mm Bore (dia), and connections with all new Fittings such as bends, elbows, tees, short pieces, connectors, back nut, reducer, diminishing pieces, caps, unions and plugs etc but except Steel tube connection, in new or old position such as fixed on Walls, Ceiling or laid in Floors or any other Situation, cleaning the same or deposit to store complete as all specified and as directed. 104.00 S&F work in repair for 16mm outer dia of CPVC water tubes SDR 11 with all fittings SDR 11 and fixed complete to walls and ceilings or laid in floors including taking down of old pipe complete all as specified and directed 105.00 S&F work in repair for 20mm outer dia of CPVC water tubes SDR 11 with all fittings SDR 11 and fixed complete to walls and ceilings or laid in floors including taking down of old pipe complete all as specified and directed 106.00 S&F 16mm bore brass MTA for CPVC pipe as in repair complete all as specified and directed. 107.00 S&F 20mm bore brass MTA for CPVC pipe as in repair complete all as specified and directed. 108.00 S&F 16mm bore brass FTA for CPVC pipe as in repair complete all as specified and directed. 109.00 S&F 20mm bore brass FTA for CPVC pipe as in repair complete all as specified and directed. 110.00 S&F 16mm bore brass elbow for CPVC pipe as in repair complete all as specified and directed. 111.00 S&F 20mm bore brass elbow for CPVC pipe as in repair complete all as specified and directed. 112.00 S&F 16mm bore brass Tee for CPVC pipe as in repair complete all as specified and directed. 113.00 S&F 20mm bore brass Tee for CPVC pipe as in repair complete all as specified and directed. 114.00 S&F 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed as in repair complete all as specified and directed. 115.00 S&F Bip tap with nozzle 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight15mm-95 gms) as in repair complete all as specified and directed. 116.00 S&F Pillar taps fancy type15mm bore of PTMT any colour screwed for iron pipe & fixed. (min weight 15mm-120gms) as in repair complete all as specified and directed. 117.00 S&F Pillar taps fancy type15mm bore of PTMT any colour screwed for iron pipe & fixed. (min weight 15mm-120gms) as in repair complete all as specified and directed. 118.00 S&F PTMT Grating Doom of 100mm dia size (Min weight 25 grms) and fixed-in-repairs, complete all as specified and as directed. 119.00 S&F PVC soap dish standard size fixed with walls incl necessary fittings & fixtures as in repair complete all as specified & directed. 120.00 S&F 32mm bore PVC waste pipe flexible type including all cups and sockets with minimum length 800mm for any type/make/size for stainless steel sinks, basins,urinal etc as in repair complete all as specified and directed. 121.00 S&F 32 mm dia Flush pipe of low/high density polyethylene pipe as directed including jointing to any type of WC and any type/size/make of low level flushing cistern and make good dismantle floor to match the existing surfaceas in repair complete all as specified and directed. 122.00 S&F PVC connection pipe 15mm size with PTMT nuts of length 450mm long as in repair complete all as specified and directed. 123.00 S&F in repair PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed. 124.00 S&F in repair PVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement, complete all as specified and as directed. 125.00 S&F in repair PVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, complete all as specified and as directed. 126.00 S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash, float valve and overflow pipealongwith PTMT Ball Valve 20mm dia , high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed. 127.00 S&F Stainless Steel Sink with Drainage Board l.0mm thick Overall size 915mm x 460mm and Bowl size 410 mm x 355 mm x 165 mm for Kitchen or Laboratory with Plugs, Washers, Brass chromium plated Waste Fitting 32mm dia, PVC waste pipe, a Pair of Cast Iron Brackets duly Painted including Cutting and Pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including Taking down/out unserviceable Sink and connected Items, complete all as specified and as directed. 128.00 S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with p or s trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat bottom cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed. 129.00 S&F in replacement Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding complete all as specified and as directed. 130.00 Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed. 131.00 S&F in repair for vitreous China urinal half stall type (back or cornerwall type) complete including providing & fixing plugs bedding urinal against wall in cement mortar 1:2, securing urinals to plugs with & including 60mm long brass screw, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe ,grating and union for discharge pipe .(Exclisive of fixing supply pipe to flushing cistern, trap and waste pipe ),complete all as specified and directed . 132.00 S&F Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and as directed . 133.00 S&F EWC Cascade type (coloured) floor mounted water closet with low level flushing cistern coloured with floor trap, PVC coloured seat cover and connecting pipe etc and making all necessary connections etc as in repair complete all as specified and as directed. 134.00 S&F in repairs Plastic seat cover white for EWC with flat bottom incl hinging device complete all as specified & directed. 135.00 S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed. 136.00 S&F Brass chromium plated fancy type bib cock screwed for 15 mm bore of pipe etc. as in repair complete all as specified & directed. Make:- Essco Cat pat No DLX 511 AKN or equivalent make as specified in the particular specfication. 137.00 S&F Brass chromium plated fancy type stop cock screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed. Make :-Essco cat part no. DLX 513BKN or equivalent model as specified in Particular specification. 138.00 S&F Brass chromium plated fancy type pillar tap screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed. Make:- Essco Cat pat No DLX 507 KN or equivalent make as specified in the particular specfication. 139.00 S&F 125 mm dia brass chromium plated shower rose with or without swivels joint for fixing to 15 mm bore pipe etc complete including taking down old one complete all as specified and directed. 140.00 S&F Towel ring of size 150mm dia decorative type fixed with walls including necessary fittings etc as in repair complete all as specified and as directed. 141.00 S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed. 142.00 S&F Central hole for Hot and Cold water supply basin mixer, brass chromium plated screwed down for iron pipes,including necessary fittings etc as in repair , complete all as specified and as directed. 143.00 S&F 3-in-1 wall mixer for Hot & Cold water supply with telephonic shower arrarengement, brass chromium plated fancy type, screwed down for 15mm bore iron pipe incl necessary fittings & fixtures etc.as in repair complete all as specified and directed. 144.00 S&F CP Kitchen sink mixture with regular swinging spout (wall mounted model) chromium plated screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed. 145.00 S&F health faucet with chomium plated with flexible cord fixed on wall screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed. 146.00 S&F Mirror Bevelled Edge 600x450mm, Selected quality Glass, mounted on 6.0mm thick AC Building Board or Commercial Ply-wood and fixed to Wooden Plugs with Chro-mium Plated Brass Screws and Cup Washers including Taking down unserviceable Mirror, complete all as specified and as directed. 147.00 Cutting/uprooting of tree from walls of bldgs. up to extended root and spraying of acid of required qty at any location of bldg up to 4 storied & making good disturbed surfaces with CM 1:4 or cement concrete (1:3:6) type C1 using 20mm graded aggregate including necessary scaffolding/ through rope with safety belt for size of tree of girth 5 to 10 cm complete all as specified and as directed by Engr -in-charge. 148.00 Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc. including cleaning all and specified and directed. 149.00 M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sq mm FRLH/S in and including concealed PVC conduit 20 mm dia medium duty ISI marked with all necessary fittings with sunken cast iron /pressed steel terminal box ,flush to surface of 1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete including cutting, chasing the surface and then making good the same in CM 1:3 to finishing the match surface complete all as specified and directed by Engr- in-charge. 150.00 All as per item No.149.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm 151.00 All as per item No.149.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size 152.00 All as per item No.149.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly complete all as specified and directed by engineer incharge. 153.00 M&L for point wiring with PVC insulated unsheated stranded copper conductor cable FRLH/S of size 1.5 sq mm in and including PVC casing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box of1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan controlled by one switch, one way complete all as specified and directed by Engineer incharge. 154.00 All as per item No.153.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm 155.00 All as per item No.153.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size 156.00 All as per item No.153.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed by Engineer-in-Charge. 157.00 All as per item No.153.00 mentioned here-in-before but using 4 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board or for AC Starter including 4 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed by Engineer-in-Charge. 158.00 S&F lamp holder insulated body with back plate for batten fittings complete all as directed. 159.00 S&F in repair lamp holder insulated body with back plate for batten fittings complete all as directed. 160.00 S & F in repair switch piano modular flush type 5/6 Amps 230V AC oneway complete all as specified and directed by Engineer-in-Charge. 161.00 S&F in repair modular socket outlet 3 pin 5/6 Amps 230 volts 1 module flush type complete all as specified and directed by Engineer-in-Charge. 162.00 S & F in repair switch piano modular flush type 16 Amps 230V AC complete one way 1 module complete all as specified and directed by Engineer-in-Charge. 163.00 S&F in repair modular bell push flush type 5 Amps 1 module complete all as specified and directed by Engineer-in-Charge. 164.00 Fixing only modular one/ two way switches, socket outlet and bell push of 1 module and of any capacity complete all as specified. Note:- Serviceable switches and socket outlet shall be obtained from item No. 151.00 mentioned here-in-before. 165.00 S&F in repair modular switch socket outlet multipurpose 3 pin 6/16 Amps 2 module complete all as specified and directed by Engineer-in-Charge. 166.00 S& F in repair modular electronic step type fan regulator by step type 230 volt 2 module complete all as specified and directed by Engineer-in-Charge. 167.00 Fixing only modular switch socket outlet and fan regulator of 2 module and of any capacity complete all as specified. Note:- Serviceable switch socket outlet and fan regulator shall be obtained from item No. 151.00 mentioned here-in-before. 168.00 S & F switch piano flush type 5/6 Amps 230V AC one way complete all as specified and directed by Engineer-in-Charge. 169.00 S & F in repair switch piano flush type 5/6 Amps 230V AC one way complete all as specified and directed by Engineer-in-Charge. 170.00 S&F socket outlet 3 pin 5/6 Amps 230 volts flush type. complete all as specified and directed by Engineer-in-Charge. 171.00 S&F in repair socket outlet 3 pin 5/6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge. 172.00 S&F bell push flush type 5 Amps 230V complete all as specified and directed by Engineer-in-Charge. 173.00 S&F call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge. 174.00 S&F in repair call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge. 175.00 S&F ceiling rose surface bakelite 65x50mm single phase complete all as specified and directed by Engineer-in-Charge. 176.00 S&F in repair ceiling rose surface bakelite 65x50mm single phase complete all as specified and directed by Engineer-in-Charge. 177.00 S&F switch socket combination 2in 1 3 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge. 178.00 S&F in repair switch socket combination 2in 1 3 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge. 179.00 S&F switch socket combination multipurpose 3 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge. 180.00 S&F in repair switch socket combination multipurpose 3 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge. 181.00 S&F ceiling fan regulator electronic Step type, solid state, 240 volts, complete all as specified and as directed 182.00 S&F in repair ceiling fan regulator electronic Step type, solid state, 240 volts, complete all as specified and as directed 183.00 S&F in repair ceiling fan regulator socket type, solid state, 240 volts, complete all as specified and as directed 184.00 Fixing only swithes, switch socket combination, ceiling rose, call bell and lamp holder, regulator etc of any capacity complete all as specified. Note:- Serviceable swithes, switch socket combination, ceiling rose, call bell and lamp holder shall be obtained from item No. 151.00 mentioned here-in-before. 185.00 S&F in repair switch socket combination with box multipurpose 3 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge. 186.00 S&F in repair switch socket combination with box 2in 1 3 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge. 187.00 Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. 188.00 S & F LED bulb 9Watts 240V 50Hz 6500K b22 base in bulb holder complete all as specified and directed by Engineer-in-Charge. 189.00 Supply and fix Decorative wall light fixture made up of Polycarbonate, suitable for 9 W retrofit LED Lamp B22 base complete with all the connection complete all as specified and directed by Engineer-in-Charge. 190.00 Supply and fixing LED ceiling fitting Recess mounted 2ft x 2ft luminaire, 35/36w, Deep drawn CRCA housing with efficacy of 100 lm/W provides uniform illumination. Designed to create best in class illumination and to be fixed in ceiling including fixing arrangement complete all as specified and directed by Engineer-in-Charge. 191.00 S&F building security light pressure die cast housing with individual LEDs with modular secondary optics security light luminaires 35 watt LED with 50mm dia light grade GI pipe bent to shape of 45 1.5 mtr long and nuts bolts including fixing arrangement complete all as specified and directed by Engineer-in-Charge. 192.00 Supply and fix plug top 3 pin16A 240V Easy to carry, Non flammable & Durable Heavy duty ,nickel plated brass terminals Long lasting polycarbonate plastic material complete all as specified and directed by Engineer-in-Charge. 193.00 S&F in replacement plug and socket in sheet metal enclosures with two pin and earth plug and socket complete with and including MCB SP 20 Amps 240 volts heavy duty all as specified and as directed by Engr-in-charge. 194.00 S&F in repair A C starter unit consisting of one 25 Amp capacity starter, one 240 V 25 Amps 10 KA SPN MCB, one 25 Amps socket and one 25 Amps plug top prewire complete all as specified and directed by Engineer-in-Charge. 195.00 S&F sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls complete for 2 modules including taking down of old unsv one complete all as specified and directed by Engineer-in-Charge. 196.00 All as per item No.195.00 mentioned here-in-before but for 3 modules 197.00 All as per item No.195.00 mentioned here-in-before but for 4 modules 198.00 All as per item No.195.00 mentioned here-in-before but for 6 modules 199.00 All as per item No.195.00 mentioned here-in-before but for 8 modules 200.00 All as per item No.195.00 mentioned here-in-before but for 12 modules 201.00 S&F modular cover plate with frame for fixing of modular switches/sockets complete for 2 modules complete all as specified and directed by Engineer-in-Charge. 202.00 All as per item No.201.00 mentioned here-in-before but for 3 modules 203.00 All as per item No.201.00 mentioned here-in-before but for 4 modules 204.00 All as per item No.201.00 mentioned here-in-before but for 6 modules 205.00 All as per item No.201.00 mentioned here-in-before but for 8 modules 206.00 All as per item No.201.00 mentioned here-in-before but for 12 modules 207.00 Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed. 208.00 S&F MCB TPN DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 4 way TPN with 200 amps rated bus bar, 415 volts complete all as specified and as directed. 209.00 S&F MCB SPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 amps rated bus bar, 240 volts complete all as specified and as directed. 210.00 S&F sheet metal enclosure for DBs when MCBs to be used 12 way single pole and neutral double door with 200 amps rated bus bar complete including connection all as specified. 211.00 S&F MCB TPN 63 to 100 amps 240 volts 10KA breaking capacity C Curve complete all as specified. 212.00 S&F MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified. 213.00 Fixing only MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified. Note:- Serviceable MCBs shall be obtained from item No. 228.00 mentioned here-in-before. 214.00 S&F in repair MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified. 215.00 S&F MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified. 216.00 Fxing only MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified. Note:- Serviceable MCBs shall be obtained from item No. 228.00 mentioned here-in-before. 217.00 S&F in repair MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified and directed by Engineer-in-Charge. 218.00 S&F sub main wiring two run of single core PVC insulated unsheathed stranded copper conductor of size 6 sqmm & one run of PVC insulated unsheathed stranded copper conductor of size 6 sqm as earth lead drawing into rigid non metalic PVC conduit of size 20mm dia including taking down old unsv complete all as specified. Note: Two run of 6 sqmm cable and one run of 6 sqmm cable will be measured as single length. 219.00 S&F sub main wiring two run of single core PVC insulated unsheathed stranded copper conductor of size 4 sqmm & one run of PVC insulated unsheathed stranded copper conductor of size 4 sqm as earth lead drawing into rigid non metalic PVC conduit of size 20mm dia including taking down old unsv complete all as specified. Note: Two run of 4 sqmm cable and one run of 4 sqmm cable will be measured as single length. 220.00 Supply and fix in repair electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete as directed.Note:- Unserviceable meter shall be deposited to store. 221.00 Supply & fix in repairs PVC flaxible 2 core cable with Copper conductor of size 0.75 sqmm from ceiling rose to fan of 1100 volts grade complete all as specified and directed. 222.00 Supply & fix in repairs 1.5 Sqmm FRLSH Copper conductor coil in existing concealed conduit 1100 volts grade complete all as specified and directed. 223.00 Supply & fix in repairs 2.5 Sqmm FRLSH Copper conductor in existing concealed conduit 1100 volts grade all as specified and directed. 224.00 S&F in replacement of PVC conduit 20 mm dia medium duty in existng wiring with accessories like MS tee, bend, elbow of high quality material size 12-20mm of 2m length complete all as directed. 225.00 Taking down and opening out the ceiling fan/wall mounted upto1200/1400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots complete including materials like split pin, rubber reel etc and reassembling and refixing of fan complete with and including minor Spares, if any required complete all as specified and as directed. Note : Spare parts shall be measured & paid separately. 226.00 Supply and fix in replacement Ceiling fan stator 48 inch sweep 12 mm copper winding including thick steel bolt with double nuts and locking pins and high quality rubber bushing to reduce vibration complete all as specified and directed by Engg-in-charge 227.00 Supply and fix in replacement rotor complete with copper winding suitable for 48 inch sweep ceiling fan complete all as specified and directed by Engg-in-charge 228.00 Supply only ball bearing suitable for 1200/1400mm sweep Ceiling fan of any make. 229.00 Supply only capacitor of 2.5 mfd for Ceiling Fan 230.00 Supply only gun metal bush of suitable size for ceiling fan of sweep 1200mm/1400mm as per existing one complete. 231.00 Supply only shafts for ceiling fan suitable for 1200mm sweep 232.00 Supply only PVC connector for Ceiling Fan 233.00 Supply only fan blades for Ceiling fan suitable for 1200mm sweep/1400mm sweep. 234.00 Supply only nuts, bolts, for Ceiling fan 235.00 Supply only rubber real insulator for Ceiling fan 236.00 Supply and fix in repair PVC canopy set (upper & lower) for ceiling fans of any sweep and make and fixing in position complete all as specified and directed by Engg-in-charge. 237.00 Supply and fix in repair MS heavy duty down rod of 15mm dia and 600mm length with necessary cutting / drilling holes and painting for ceiling fans complete all as specified and directed by Engg-in-charge. 238.00 Supply & Fix in repair ceiling fan mild steel body set (upper & lower) for ceiling fans of any sweep and make and fixing in position complete all as specified and directed by Engg-in-charge. 239.00 M&L for painting of ceiling fan/wall fan/exhaust fan of any size and sweep complete with synthetic enamel paint by spraying including filling with cavities with filler, after cleaning all dust etc complete all as specified and directed by Engineer-in-Charge. 240.00 Taking down and opening out the exhaust fan upto 400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots rubber reel etc. reassembling and refixing of fan complete including all as specified and as directed. 241.00 Supply and fix in replacement exhaust fan stator upto 400 sweep , copper winding including thick steel bolt with double nuts and locking pins and high quality rubber bushing to reduce vibration complete all as specified and directed by Engg-in-charge 242.00 Supply and fix in replacement rotor complete with copper winding suitable for 300 sweep exhaust fan all as specified 243.00 M&L for painting of exhaust fan of any size and sweep complete, in situ with approved colour synthetic enamel paint by spraying including filling with cavities with filler, one coat after cleaning all dust etc. 244.00 Supply only bush suitable for exhaust fan. 245.00 Supply only ball bearing suitable for exhaust fan. 246.00 Supply only capacitor 2.5 mfd for exhaust fan. 247.00 S&F in replacement MS louvers with shutter of exhaust fan upto any sweep upto 12th storey building complete including arrangement of scaffolding for fixing of louvers with all nuts, bolts and washers and finished properly with cement work as per existing complete all as specified and as directed by engr in charge 248.00 Taking down carefully unserviceable geyser of any type and make from site after disconnections of water & electrical connections & carrying out to MES store yard for inspection and thereafter to workshop for repair & replacement of components such as heating element, thermostate, cable, neon lamp, plugtop, outer casing, plates & repair work to apparatus plate, copper tank,split plate including de-scaling of water tank etc and carrying back to MES store yard for testing and refixing at site and making water & electrical connection on completion and all as directed. 249.00 M&L for brazing/gas welding of inner container copper of 25 ltrs /50 ltrs capacity and any make and making leak proof all as directed. 250.00 Supply only following spares for geysers:-Heating element 2.00KW including rubber gasket ISI marked suitable for existing geysers. 251.00 Thermostate for suitable existing geyser of 25/50 litrs capacity 252.00 Chromium plated copper pipe of length not less than 60cm including washers for incoming & outgoing hot & cold water connections as specified and directed by Engr-in-charge 253.00 Apparatus plate assembly complete for geyser of capacity 25/50 litrs capacity. 254.00 Outer casing made out of 22 SWG MS sheet suitable for geyser of capacity 25 litrs. 255.00 Storage tank fabricated from copper sheet gauge suitable for geyser of capacity 25 ltrs of make as specified and approved. 256.00 Split plate bottom cover made out of 22 SWG MS sheet suitable for 25 litrs capacity geyser 257.00 Split plate top cover made out of 22 SWG MS sheet suitable for 25 litrs capacity geyser 258.00 Insulating material glass wool 259.00 Element holding brass stud 260.00 Element holding MS clamp 261.00 Fusible metal plug 262.00 Neon lamp round/square with connection lead 263.00 Non return valve for geyser inlet1 Old Unserviceable Brick bats Cum 5.50 750.00 4125.00 2 Old Unserviceable chowkat with sutter incl all fittings and fixtures area exc.1.50sqm but n.exc. 4.00sqm Each 8.00 350.00 2800.00 3 Old Unserviceable chowkat with sutter incl all fittings and fixtures area n. exc.1.50sqm Each 8.00 250.00 2000.00 4 Old Unserviceable door shutter incl all fittings and fixtures n. exc. 1.00 sqm Per 5.00 250.00 1250.00 5 Old Unserviceable door shutter incl all fittings and fixtures area exc. 1.00 sqm & n. exc 2.00 Sqm Per 8.00 250.00 2000.00 6 Old Unserviceable Timber Scantlings of any description Cum 0.30 5000.00 1500.00 7 Old Unserviceable Timber Fillets of any description RM 30.00 10.00 300.00 8 Old Unserviceable iron scrap Kg 310.00 20.00 6200.00 9 Old Unserviceable Brass scrap Kg 20.00 200.00 4000.00 10 Old Unserviceable PVC scrap Kg 10.00 10.00 100.00 11 Old Unserviceable Aluminium scrap Kg 30.00 100.00 3000.00 12 Old Unserviceable Building hardware such as Mild Steel Butt hinges, Aluminum tower bolts, Aluminum Handle, Steel Concealed Hinges, cupboard knobs of any size Each 178.00 5.00 890.00 13 Old Unserviceable Aluminum Sliding Door Bolt, Door Closer hydraulically, Steel Floor door stopper, MS Mortice lock, MS Mortice night latch, floor spring hydraulically, MS Safety lever locks etc of any size Each 28.00 25.00 700.00 14 Old Unserviceable rolling shutter of any size RM 15.00 300.00 4500.00 15 Old Unserviceable MS Drapery rod with stainless steel bracket of any size RM 50.00 25.00 1250.00 16 Old Unserviceable CGI/PGI roof sheet of any description Sqm 115.00 75.00 8625.00 17 Old Unserviceable Wall and ceiling board in any description Sqm 100.00 20.00 2000.00 18 Old Unserviceable Powder coated Aluminium door, window,ventilator,partition of any description Sqm 27.00 50.00 1350.00 19 Old Unserviceable stainless steel wire mesh Sqm 10.00 10.00 100.00 20 Old Unserviceable brass MTA, FTA, elbow, Tee etc of any size Each 20.00 15.00 300.00 21 Old Unserviceable PTMT/PPR Ball valves, PVC Bend, PVC Junction, PVC waste/ flush pipe, waste fittings, grating, PVC connection any size and description Each 87.00 25.00 2175.00 22 Old Unserviceable PTMT bip tap, stop cock, pillar tap, Angular Stop cock, tower rail, shower with arm, of any description Each 30.00 10.00 300.00 23 Old Unserviceable bip tap, stop cock, pillar tap, Angular Stop cock, Two way bib cock, Glass shelf assembly, Glass corner shelf , shower rose and arm, Chromium plated bottle trap, waste coupling of any description Each 30.00 25.00 750.00 24 Old Unserviceable CP basin mixer, Wall Mixer, Kitchen sink mixture of any description Each 4.00 75.00 300.00 25 Old Unserviceable stainless steel grating of any size and description Each 5.00 10.00 50.00 26 Old Unserviceable health faucet, cp toilet paper holder, cp soap dish, towel ring, towel rail jet spray, CP connector of any description Each 29.00 15.00 435.00 27 Old Unserviceable PVC seat cover, PVC tank lid/cover,PVC Syphon assembly of any description Each 8.00 10.00 80.00 28 Old Unserviceable Mirror of any description Each 5.00 25.00 125.00 29 Old Unserviceable Kitchen sink, plate rack of any description Each 1.00 150.00 150.00 30 Old Unserviceable flushing cistern, bathroom cabinet Each 8.00 25.00 200.00 31 Old Unserviceable GI pipeline 15mm bore of any description RM 20.00 20.00 400.00 32 Old Unserviceable GI pipeline 20mm bore of any description RM 10.00 25.00 250.00 33 Old Unserviceable PVC /CPVC water tubes of any size and description RM 70.00 15.00 1050.00 34 Old Unserviceable water storage tank 1000 liter of any description Each 2.00 750.00 1500.00 35 Old Unserviceable copper / aluminium point wiring. Per Point 56.00 35.00 1960.00 36 Old Unserviceable switch piano, socket outlet, Switch Socket Combination, ceiling rose, regulator, bell push, call bell, bulb holder any type and description Each 354.00 3.00 1062.00 37 Old Unserviceable LED light fittings of any description Each 30.00 50.00 1500.00 38 Old Unserviceable LED building security light of any description Each 2.00 65.00 130.00 39 Old Unserviceable plug top,plug and socket in sheet metal enclosures, A C starter unit of any description Each 18.00 25.00 450.00 40 Old Unserviceable sunken flush metal GI boxes of any description Each 18.00 10.00 180.00 41 Old Unserviceable modular cover plate of any description Each 18.00 1.00 18.00 42 Old Unserviceable MCB DB of any capacity Each 3.00 35.00 105.00 43 Old Unserviceable MCB SP/DP/TPN of any capacity Each 58.00 10.00 580.00 44 Old Unserviceable Submain wiring any size RM 75.00 15.00 1125.00 45 Old Unserviceable Capacitor of any capacity Each 51.00 3.00 153.00 46 Old Unserviceable rotor,stator of any capacity Each 86.00 3.00 258.00 47 Old Unserviceable ball bearing Each 70.00 2.00 140.00 48 Old Unserviceable fan bush, PVC canopy set Each 78.00 1 78.00 49 Old Unserviceable shaft Each 42.00 3.00 126.00 50 Old Unserviceable fan blades Set of 3 35.00 10.00 350.00 51 Old Unserviceable MS down rod Each 35.00 10.00 350.00 52 Old Unserviceable nuts,bolts Each 35.00 1.00 35.00 53 Old Unserviceable burnt copper winding of ceiling/exhaust fan. Each 42.00 80.00 3360.00 54 Old Unserviceable PVC cassing caping/ concealed conduit RM 5.00 5.00 25.00 55 Old Unserviceable copper/aluminium conductor RM 180.00 2.00 360.00 56 Old Unserviceable MS Louvers Each 12.00 50.00 600.00 57 Old Unserviceable Heating element of any type Each 6.00 20.00 120.00 58 Old Unserviceable Thermostat of any type Each 6.00 25.00 150.00 59 Old Unserviceable Chromium plated copper pipe of any type Each 12.00 20.00 240.00 60 Old Unserviceable Apparatus plate of any type Each 6.00 40.00 240.00 61 Old Unserviceable Outer casing for geyser of any type Each 6.00 35.00 210.00 62 Old Unserviceable copper storage tankfor geyser of any type Each 6.00 40.00 240.00 63 Old Unserviceable split plate bottom/top cover of any type Each 6.00 5.00 30.00 64 Old Unserviceable metal plug Each 6.00 10.00 60.00 65 Old Unserviceable NRV Each 6.00 20.00 120.00 66 Old Unserviceable Pressure Reducing Valve Each 6.00 50.00 300.00
