|
| 1 | Repair & painting of cook room doormitory near Mega Boys Hostel |
| 2 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm. |
| 4 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws |
| 5 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 6 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm |
| 7 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm |
| 8 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessaryscrews etc. complete : 125 mm |
| 9 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 10 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 11 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 12 | Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : Two or more coats on new work |
| 13 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 14 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 15 | Providing and fixing double scaffolding system (cup lock type) on theexterior side, up to seven story height made with 40 mm dia M.S. tube1.5 m centre to centre, horizontal & vertical tubes joining with cup & locksystem with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircasesystem in the scaffolding for working platform etc. and maintaining it in aserviceable condition for the required duration as approved and removingit there after. The scaffolding system shall be stiffened with bracings,runners, connection with the building etc wherever required for inspectionof work at required locations with essential safety features for the workmenetc. complete as per directions and approval of Engineer-in-charge. Theelevational area of the scaffolding shall be measured for payment purpose.The payment will be made once irrespective of duration of scaffolding. |
| 16 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5sqm and under, including cutting the patch in proper shape, raking outjoints and preparing plastering the wall surface with white cement basedpolymer modified self curing mortar, including disposal of rubbish, allcomplete as per the direction of Engineer-In-Charge. |
| 17 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below |
| 18 | Dismantling of flushing cistern/wc/.washbasin of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 19 | Dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping groundwithin 50 metres lead |
| 20 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 21 | Providing and fixing panelling or panelling and glazing in panelled orpanelled and glazed shutters for doors, windows and clerestory windows(Area of opening for panel inserts excluding portion inside grooves orrebates to be measured). Panelling for panelled or panelled and glazedshutters 25 mm to 40 mm thick. Float glass panes 4 mm thick glass pane (weight not less than10 kg/sqm). |
| 22 | Dismantling tile work in floors, walls and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 23 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in-Charge. |
| 24 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe 32 mm dia |
| 25 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 26 | Providing and fixing vitreous china dual purpose closet suitable for use assquatting pan or European type water closet (Anglo Indian W.C pan) withseat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low levelflushing cistern with fitting and brackets, 40 mm flush bend, 20 mm overflow pipe, with specials of standard make and mosquito proof couplingof approved municipal design complete, including painting of fittings andbrackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solidplastic seat and lid with white vitreous china flushing cisternand C.P. flush bend. |
| 27 | Providing and fixing C.P. brass bib cock of approved make and model as per directions of Engineer-incharge. |
| 28 | Providing and fixing C.P. brass long body bib cock of approved qualityconforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 29 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the cost ofEPDM rubber / neoprene gasket required (Fittings shall bepaid for separately) Powder coated aluminium (minimumthickness of powder coating 50 micron) |
| 30 | Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge. |
| 31 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make. |
| 32 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. 50 mm average thickness in 3 layers. |
| 33 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.30 mm thick |
| 34 | Taking out old Aluminium tube false ceiling of any dia including existing angle/tee frame work for repair to existing/replacementcast iron pipes/fittings and re-fixing the same after repair with new stainless steel screws to make good the same (Rate i/c all operation involved for false ceiling) including disposal of unserviceable surplus material with in 50 meters lead as directed by Engineer-in-charge. |
| 35 | Providing and applying repair mortar of Universal Repair product 301 of Dr. Fixit or Equivalent to SCI/CI pipe. Prepare the mortar joints using a hammer and chisel to remove any deteriorated mortar to a depth of ¼ inch to ¾ inch. Clean out the joint using a wire brush. Apply the mortar repair with one part of URP and 1.5 part of cement on the existing joints and as per direction of engineer in charge. (Rate includes all operations of cleaning and filling the joints. Nothing extra shall be paid.) 100 mm diameter |
| 36 | Grouting the joints of flooring tiles 300x300mm having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 37 | Removing Stainless steel drain cover at bathroometc. and repairing the hole with waterproofing chemical Dr Fixit 301 or eq.with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20 mm nominal size) orMicro concrete etc. , including finishing complete so as tomake it leak proof and install the stainless steel hole drain cover complete as per direction of engineer enchagre |
| 38 | Credit for dismantled pvc shuters |
