Misc. Civil Works At Acos, Pratapgarh - Renewing Glass Panes, With Putty And Nails Wherever Necessary Float Glass Panes Of Thickness 4 Mm Supplying And Fixing Fixed Wire Gauge Of 14 Mesh X 24 Gauge To The Metal Frame Of Rolled Section By Metal Beading 20, Chittorgarh-Rajasthan

Misc. Civil Works At Acos, Pratapgarh - Renewing glass panes, with putty and nails wherever necessary Float glass panes of thickness 4 mm Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish:20mm thick. Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 (1-Cement: 6-Sand). Providing & fixing precast cement concrete coping 1 24 mix 50mm thick complete as per specification Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering All work up to plinth level. 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size). Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1) cement: 3 coarse sand) and making good the joints and cost of plastizers(if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft. bases of columns etc. Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1: 6 (1 cement: 6 coarse sand) Half brick masonry in Superstructure, above plinth level upto floor V level using bricks of designation 75 Cement mortar 1:6 (1) cement: 6 coarse sand) Add extra providing and placing in position 2 Nos. 6mm Ø M.S. bar at every third course of half brick masonry Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (Original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Hot rolled deformed bars (IS: 1139). Providing and fixing M.S. sheet Imm thick single leaf door shutter in angle iron frame 35 * 35 * 5mm suitabilly diagonally braced with 25 * 3mm flat iron above and below lock rail of size 50 * 5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (Icement: 3 coarse sand 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approvall steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required: Windows side hung Ventilators top or centre hung (openable) Deduct for Pina headed 4mm thick glass panels is used instead of 4mm thick plain glass Providing and fixing Square bars or other flat welded to window, ventilatiors etc. Providing and fixing Square bars or other flat welded to window, ventilatiors etc. Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15 * 3 mm lugs 10cm long embedded in cement concrete blocks 15 * 10 * 10 cm of 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges

Refer document

INR 4 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB