Tender For Special Repair Of Sandalpur Kudhawal Road (Odr) (Km.5 To 8) - Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory rollerin stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. (Grading II) (MORTH 4.11) A. By Manual Means 2 Providing and applying tack coat with bitumen (VG-10) using bitumen pressure distributor at the rate of 0.20kg per sqm on the prepared bituminous surface cleaned with mechanical broom. (MORTH 5.02) (i) 3 Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregatesusing Viscocity grade bitumen (VG-10) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable hot mix plant (120 TPH) of appropriate capacity not less than 200 tonnes/hour, laying and rolling with a smooth wheeled roller, finished to required level and grades. (MORTH 5.07) 4 Providing and laying of premix sand seal coat with HMP (120 TPH) of appropriate capacity not less than 200 tonnes/ hours using crushed stone chipping 6.7 mm size and penetration bitumen of suitable grade. (Bitumen VG-10) (MORTH 5.07) Case - II : Type B 5 Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (MORTH 3.18) 6 Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing. (MORTH 6.02) 7 Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (MORTH 3.06) (301) 8 Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. (MORTH 12.04) 9 Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications. Clause 1300 (MORTH 12.05) 10 Pointing with cement mortar (1:3) on brick work in substructure as per Technical Specifications Clause 1300 (MORTH 12.05) 11 Plastering with cement mortar (1:3) on brick work in sub-structure as per Technical Specifications 1300 & 2200 (MORTH 13.03) 12 Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications 1500, 1700 and 2100. (Morth 9.06) (C) RCC Grade M20 Case-II RCC Grade M20 using batching plant transit mixer & manual placing 13 Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications - 1600. (Morth 9.07) 14 Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (MORD 9.3 (B) 1000 mm dia
