Tender For Repair/Replacement Of Joinery, Steel Gate, Rolling Shutter Inside Cod Under Age B/R-I Of Ge (I) Kanpur Cantt; 1 Taking down chowkhats or frame exc 1.50 sqm but n.exc. 4.00 Sqm each with shutters (without taking off shutter from frame) etc complete all as specified and directed. 2 Taking down shutter exceeding 1.00 Sqm butnot exceeding 2.0 Sqm each complete all as specified and directed. 3 M&L solid PVC frame (single rebated) of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet with homogenious fine cellular structure having smooth outer integral skin with suitable metal stifner & fixed with 100x8 sheet metal CSK (copper screws) screws complete all as specified and directed. 4 M&L factory made solid panelPVC moulded door shutter with wood free EPS 28 to 30 mm thick (style) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plan colour PVC sheet on back face, supply & fix in frame at site complete all as specified and directed. 5 S&F 100 mm long PVC butt hinges complete all as specified and directed. 6 S&F 150 mm long PVC handle complete all as specified and directed. 7 S&F 150 mm long PVC barrel tower bolt complete all as specified and directed. 8 S&F for powder coated Aluminium door partly glazed (using 5mm thick glass) and partly panelled or fully Glazed (using 12mm thick both side prelaminated board Noavapan Kitlam) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl125mm dia circular aluminium handle tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door spring of sandhu/sanant make, two numbers door stopper, hinges (three Nos each side) etc and aluminium frame of section 100x44.45x2.00mm thick complete all as specified and directed. 9 S&F forAluminium anodised door partly glazed (using 5mm thick glass) and partly panelled or fully Glazed (using 12mm thick both side prelaminated board Noavapan Kitlam) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl125mm dia circular aluminium anodised handle tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door spring of sandhu/sanant make, two numbers door stopper, hinges (three Nos each side) etc and aluminium frame of section 100x44.45x2.00mm thick complete all as specified and directed. 10 S&F Pressed steel door frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc. Size 105x60mm complete all as specified and directed. 11 M&L plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) in bed block or hold fasts incl necessary form work complete all as specified and directed. 12 S&F Mild Steel holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position complete all as specified and directed. 13 M&L for 35 mm thick 2nd class hard woodglazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, provided with stiles and rails as specified in SSR Part-I Section-8 clause 8.20 (a) fixed to chowkats complete all as specified and directed 14 S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed 15 M&L 2nd class HW as inplain , solid, straight chowkhats and frames , wrought , framed , rebated on the solid, rounded or chamfered, put together with glue pinned joints complete all as specified and directed. 16 S&F of 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. Note : Manufacturer test certificate and PVrs shall be submitted by contractor before claiming payment against this item complete all as specified and directed. 17 Material & Labour two coats of synthetic enamel paint over and including a coat of pink primer to new wooden surface of any description over 10 cm width or girth including preparation of new surface complete all as specified and directed. 18 S&F MS butt hinges medium weight cold rolled 100 mm size complete all as specified and directed. 19 S&F of 200 mm long barrel tower bolt aluminium anodised of extruded section and fixed complete all as specified and directed. 20 S&F of 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. 21 S&F of 300 mm long aluminium anodised sliding door bolt with hasp and staple and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed. 22 Taking down chowkhats or frame n.exc 1.50 sqm with shutters (wihtout taking off shutter from frame ) etc complete all as specified and directed. 23 S&F Aluminium powder coated window/CSW (partially openable type) with aluminium anodized frame of aluminium section 62.5x37x2.5 mm thick with shuttershaving styles & top rail of aluminiumsection 44.45, glazing clips, rubber packing, aluminium snap beading, screws anodized, aluminium fitting such as hinges, tower bolts handles etc including 5.5 mm thick ordinary plain glass complete all as specified and directed. 24 M&L for powder coated aluminiumglazed window shutters with frame openable, section for aluminium frame 100 x 45 x 2.00mm thick & section for shutter 45 x 44.45 x 1.90 mm thick incl provision of opening for window AC opening and5mm thick ordinary plain glass with rubber beading clip, hinges, handles, tower bolts etc complete all as specified and directed. 25 M&L for powder coated aluminium grill of mesh size 65 x 75mm of 6mm dia of aluminium bar fixed with Y or H aluminium sec complete all as specified and directed. 26 M&L in repairpower coatedaluminimum grill of mesh of size 65 mm X 75 mm of 6 mm dia of aluminium bar fixed withYorH aluminium sec complete all as specified and directed. 27 S &F in repair of aluminium door clip tee and rubber beadings for fixing glass complete all as specified and directed 28 S&F in repair 5 mm thick tinted glass of aluminium door exc.0.5 sqm each pane complete all as spd and directed 29 S&F in repair12 mm thick Prelaminated particle board, exterior grade, prelaminated bothside with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame /steel fram complete all as specified and directed. 30 S &F in repair mild steelmartice lock vertical type size 100 mm in 4 levers complete all as specified and directed 31 M&L in repair door double action Floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governig pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed. 32 S&F in repair 150 mm lengthfloor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and directed. 33 Taking down and refixing of aluminium door complete all as specified and directed. 34 S&F steel windows with side hung shutters using seel section with glazing bars includingprojectedbox type hinge, steel handle, steel peg stay etcdovetailed or welded complete all as specified and directed. 35 S&F steelventilators with top hunh shutter & glazing bars hinges, steel peg stay complete all as specified and directed. 36 S&F steel windows for industrial buildings fixed type with glazing bar complete all as specified and directed. 37 S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 38 S&F MS work as in doors framing / chowkhates/kaging/Ventilator for cladding, glazing and the like fixed with angle cleats connecting plates, etc conforming to (Fe-290) Gde E-165 complete all as specified anddirected. 39 S&F steel wire fabric not exc. 4 kg/ sqm in wood or steel members etc complete all as specified and directed. 40 Hacking out old broken glass (any thickness ,size ,quality or desceiption) form wooden frames or stone,cocrete or brick surrounds glazing with putty or fixed with beads complete all as specified and directed. 41 M&L for 3 mm thick sheet glass ordinary quality and glazing withoil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed 42 All as per item No 41.00 abovebut figured glass,pin head type complete all as specified and directed. 43 S&F 4.8 mm thick sheet glass any colour ordinary quality and glazing with putty in square n.exc 0.5 sqm min each pan all as specified and directed. 44 Dismantling of aluminium partition in any description incliuding glass and board complete all as specified 45 S&F powder coated aluminium partitionwith aluminium tube of section 114x44.45x1.90mm thick at bottom and remaining vertical and horizontal rails of section 44.45x45x1.9mm thick and top rail of section 44.45x45x1.90mm thick with aluminium anodized clips, rubber, beading, aluminium angle, nut bolt etcboth side laminated 12mm thick at bottom ,ISI marked and top parts of partition shall be covered with plain floatglass of 5.0mm thickcomplete all as specified and directed. 46 S&F for Powder coated aluminium(minimum thickness of powdercoating 50 micron) work for doors,windows, ventilators andpartitions (Fixed portions) withextruded built up standard tubular sections/ appropriate Z sections and other sections ofapproved make conforming to IS:733 and IS:1285, fixing with dashfasteners of required dia and size,including necessary filling up thegaps at junctions, i.e. at top,bottom andsideswithrequiredEPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitredand jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainlesssteel screws complete all as specified and directed. 47 M&L for preparation of new steel surfaces any description not other wise described over 10 Cm width or girth and applying two coat of Synthetic Enamel paint over and including a coat of red oxide primer all as specified and as directed. 48 Taking down steelrolling shutterincludingball bearing,top cover anchoring rod exc5 Sqmbut not exc 15 Sqm each complete all as specified and directed. 49 S&F steel rolling shutters without ball bearings 1.00 mm thickness of lath including top cover, anchoring rod, hasp and staple, guide channel and one shop coat primer, erected in position as indicated complete including taking down of the samepush pull or manual type complete all as specified and directed. 50 All as per item No 49 above but gear operated type with bevel gear box and crank handle complete all as specified and directed. 51 All as per item No 49 above but gear operated type with chain wheel and hand chain complete all as specified and directed. 52 S&F Ball bearing for rolling shutters complete all as specified and directed. 53 S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. 54 Taking down of rolling shutter of area exceeding 8 sqmif necessary on ground, overhauling and welding etc ofrolling shutters (push pull or manual type) including oiling, greasingwherever is require including in guide chanel also and erected in the same position after changing of defective part if any including two coat of synthetic enemal paint over and including a coat of red oxide primer on steel shutter complete all as specified and directed.(Note- Defective partsshall be measured and paid separately as supply only underitem no 55 to 60 and fixing of parts shall deemed to be included in this item ) 55 Supply only 1.0mm thick lath matching with existing for rolling shutters complete all as specified and directed. 56 Supply only Ball bearing for rolling shutters complete all as specified and directed. 57 Supply only Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. 58 Supply only 1 mm thick hood cover of mild steel sheet with necessary fixing arrangement for rolling shutters complete all as specified and directed. 59 Supply only springfor rolling shutters complete all as specified and directed. 60 Supply only MS guide rail 2 mm thick for rolling shutters complete all as specified and directed. 61 S &F in repairmild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering and hanging or sliding also fastening and fixing complete for Fe-410- W (Gde- E-250) quality-B complete all as specified and directed. 62 S&F in repair 0.63 mm thick galvanised, corrugated mild steel sheeting with zinc coating120 gram/sqmtwo corrugationsside lap & 150 mm end lap ,fixedwith nutbolt and washers or with self drilling zink allunium coated metal screws of suitable size having cap complete all as specified and directed. 63 S&F in repair 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed. 64 S&F in repair of 1.00 mm thick Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. 65 S&F in repairsteel wire fabric not exc. 4 kg/ sqm in wood or steel members etc complete all as specified and directed. 66 S&Fin repairbutt hinges, medium weight, cold rolled mild steel, and fixed (Size of hinges in 100 mm) complete all as specified and directed. 67 S&F in repairPVCButt hinges,(Size of hinges in 100 mm) complete all as specified and directed. 68 S&Fin repair200 mm long Aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. 69 S&F in repair 150mm long alluminiumhandles, cast type, anodized and fixed complete all as specified and directed. 70 S&Fin repairmild steelsliding door bolt 300 mm long stove enamelled black with bright bolt not less than 16 mm dia with and including and minimum of 6 boalts and nuts four on bolt plat and two on staple plate and fixed etc complete all as specified and directed. 71 M&L for preparation of old painted steel surface on any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enameled paint including necessary scaffolding and saftey precautions upto height 5 metre complete all as specified and directed. 72 Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets. complete all as specified and directed. 73 Providing & Fixing Ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595mm of approved 12mm thick micro tegular edged GRG false ceiling tiles, design and patterns having moisture content less than 2% humidity resistance of 99%, NRCO .50 to 0.75 as per IS 8225 : 1987, Noncombustable as per BS 476 (part 4 ) -1970 and light reflectance of 85% (minimum) including and to be laid in true horizontal level suspended on interlocking metal T-Grid of not dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. 74 M&L Solid PVC wall lining complete consisting of 5 mm thick single side prelaminated PVC sheet used instead of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame incl PVC beading in same colour at bottom and top as per design as approved by the Engineer in charge complete all as per manufacturers specification complete all as specified and directed. 75 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 76 S&F wind ties for roof including securing bolts as directed , including all necessary drilling , bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 77 S&F in repairs fancy type stainless steel curtain rods of 25 mm dia for doors/ windows etc including SS brackets and SS funnels/dome complete all as specified and directed. 78 Demolition of Brickwork built in cementmortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articlescomplete all as specified anddirected. 79 M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius in brick thick wallbuilt in CM 1:6 complete all as specified and directed. 80 All as per item No 79 above here in before but except bricks.including cleaning of bricks complete all as specified and directed.Note : Old serviceable bricks obtained vide item No 78 aboveshall be reused. 81 Taking down cement plaster from brick wall including racking out joints, hacking for key & scrubbing down complete all as specified and directed. 82 M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of concrete or brick surface finished even and smooth without using extra cement mixed wiith water proofing compound 3% by weight of cement or as per manufacturer instruction complete all as specified and directed. 83 M&L for 15 mm thick rendering in cement mortar 1:6 on fair faces of concrete or brick, finished even and smooth without using extra cement complete all as specified and directed. 84 M&L for 10 mm thick cement plaster on ceiling in CM 1:3 finished even and smooth without using extracement complete all as specified and directed. 85 Supply only water proofing compound (ISI marked) complete all as specified and directed. 86 M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper on surfaces of wall over and including a coat of primer complete all as specified and directed. 87 M&L for preparation of newly plastered surfaces of wall and applyingtwo coat of cement base paint over and including a coat of cement primer complete all as specified and directed. 88 M&L for preparation of newly plastered surfaces of wall and applyingthree coats of white wash as on ceiling surfaces complete all as specified and directed. 89 S&F in repairs galvanised mild steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with wooden beads to wooden joinery complete all as specified and directed. 90 S&F in repair aluminium (diecast body)hydraulically regulateddoor closer designation NO- 3, universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. 91 Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges complete all as specified and directed. 92 Dismantiling ofCGI/PGI sheets any thicknessas in roof coverings complete all as specified and directed. 93 S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws of required size and dia complete all as specified & directed 94 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws of required size and dia complete all as specified and directed. 95 Dismantling of unframed work timber scantlings 40 sqcm and over in section, in any position complete all as specified and directed. 96 S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410 W (Gde-E-250) quality A complete all as specified and as directed.
