|
| 1 | M & L for AMF panel board outdoor type made out of CRCA sheet 3.15mm thick totally enclosed, weather, dust and vermin proof with front opening, 440 volts, 3 phase, 4 wire, 50 Hz having Aluminium bus bar of 800 A capacity for three phases and nuetral duly colour coated with coloured heat shrinkable PVC sleeves, Multifunctional digital control relay for AMF operaration and display of electrical parameters, manual start/stop facility, Two Nos Electrically operated contactor 4 pole of suitable capacity for DG set and main supply, complete all as specified, with on/off controller indicator, phase indicators, engine start push button and fault accept/reset push button including battery charger comprising transformer, rectifier, resistance, suitable capacity AC volt meter, AC ammeter, frequency meter and charge rate selector switch, suitable MCCB for short circuit & over load protection including all accessories prewired with suitable size copper conductor cable or strip complete all as specified and directed by Engr - In- Charge. |
| 2 | Incoming. (a)500-630A FP 36 KA (DN3-630D) MCCB - 02 Nos(b)Sprader Terminal DN3-630 - 4 Pole (Set of 8) - 04 Nos(c)600A FP Contactor (MCX 45)- 02 Nos(d)Three phase MFM Meter -01 No(e) Digital DC Amp Meter - 01 No(f)Digital DC Volt Meter - 01 No(g) R-Y-B Indication Lamp - 03 Nos(h) Red-Green Push Button - 03 Nos(j) 600/5 Ring Type Cl-1 VA-15CT - 03 Nos(k) 6 A SP \"C\" MCB- 06 Nos (l)16 A SP \"C\" MCB- 02 Nos(m)16 A DP \"C\" MCB- 04 Nos (n) Selector Switch 3P 3W 16A - 01 No(o) Selector Switch 4P 2W 6A - 01 No(p) E-Stop Push Button - 01 No(q) AMF Controller - 01 No(r)8 Channel 1 C/O Relay Card 24 V DC - 01 No(s) Battery Charger 24 V DC 10 A - 01 No(t)Hooter - 01 NoOutgoing.(a) 50 - 63 A FP 18 KA (DU100D) MCCB - 10 Nos |
| 3 | M & L for AMF panel board outdoor type made out of CRCA sheet 3.15mm thick totally enclosed, weather, dust and vermin proof with front opening, 440 volts, 3 phase, 4 wire, 50 Hz having Aluminium bus bar of 500 A capacity for three phases and nuetral duly colour coated with coloured heat shrinkable PVC sleeves, Multifunctional digital control relay for AMF operaration and display of electrical parameters, manual start/stop facility, Two Nos Electrically operated contactor 4 pole of suitable capacity for DG set and main supply, complete all as specified, with on/off controller indicator, phase indicators, engine start push button and fault accept/reset push button including battery charger comprising transformer, rectifier, resistance, suitable capacity AC volt meter, AC ammeter, frequency meter and charge rate selector switch, suitable MCCB for short circuit & over load protection including all accessories prewired with suitable size copper conductor cable or strip complete all as specified and directed by Engr - In- Charge. |
| 4 | Incoming (a)320-400A FP 36 KA (DN3B-400D) MCCB - 02 Nos(b)Sprader Terminal DN3B/DN3-400 - 4 Pole (Set of 8) - 04 Nos(c)400A FP Contactor (MCX 43)- 02 Nos(d)Three phase MFM Meter -01 No (e) Digital DC Amp Meter - 01 No (f)Digital DC Volt Meter - 01 No (g) R-Y-B Indication Lamp - 03 Nos(h) Red-Green Push Button - 03 Nos (j) 400/5 DIN Type Cl-1 VA-15CT - 03 Nos(k) 6 A SP \"C\" MCB- 06 Nos (l)16 A SP \"C\" MCB- 02 Nos(m)16 A DP \"C\" MCB- 04 Nos (n) Selector Switch 3P 3W 16A - 01 No (o) Selector Switch 4P 2W 6A - 01 No(p) E-Stop Push Button - 01 No (q) AMF Controller - 01 No(r)8 Channel 1 C/O Relay Card 24 V DC - 01 No(s) Battery Charger 24 V DC 10 A - 01 No(t)Hooter - 01 NoOutgoing (a) 200 - 250 A FP 25 KA (DU250C) MCCB - 01 No (b) Sprader Terminal DU250C/DU250-4 Pole (Set of 8)-01 No(c)80 - 100 A FP 18 KA (DU100D) MCCB - 04 Nos |
| 5 | Supply, installation, commisioning and testing factory made and tested, CPRI approved,LT Panel(KISOK), outdoor type, mounted on rigid angle iron frame, suitable size, having independent compartment forinsulated Aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 3.00 mm thick CRCA sheetsuitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with aluminium bus bar of600 Amp rating for 3 phase and neutal4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, common earth bus bar ofGI Strip 32 x 6 mm at bottom with panel board at two earth terminals , cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coatingin siemens grey colourfront & rear opening type with double door shutter and locking arrangement including provision of 65 mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/exist including taking down and refixing of exisiting cable properly with lug and thimable, Rate including for removal and taking out existing old/rusted LT Panel board of any type any size complete all as specified and directed by Engr - In- Charge and comprising as under: - |
| 6 | Incoming :- (a) ON load change over switch of 400 Amp Capacity- 01 No(b) MCCB 4 Pole, current rating 400 Amp, With Thermal Magnetic release, breaking capacity 36 kA at 415V, 50Hz- 01 Nos.(c)Digital voltwith selector switch.-01 set. (d)DigitalAmp meter with selector switch.-01 set. (e)Neon indicating lamps (R, Y & B) -01` Set.Out going :- (a) MCCB 4 Pole, current rating 200 Amp, With Thermal Magnetic release, breaking capacity 25 kA at 415V, 50Hz - 01 No.(b) MCCB 4 Pole, current rating 160 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz - 01 No.(c) MCCB 4 Pole, current rating 125 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz - 01 No.(d) MCCB 4 Pole, current rating 100 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz - 01 No.(e) MCCB 4 Pole, current rating 63 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz - 02 Nos.(f) Angle iron base frame as reqd size as per above panel, total leg height 600 mm and grouting in side PCC 150 mm legsand made out of ISA5050, 50 x 50 x 6 mm thick angle iron duly painted - 01 No.(g) M & L for necessary excavation and as reqd PCC 1:3:6 (40 mm graded aggregate) Type C2 for foundation of angle iron legs frame work complete - 01 Job |
| 7 | Supply, installation, commisioning and testing factory made and tested, CPRI approved,LT feeder pillar box (KISOK), indoor type, mounted on rigid angle iron frame, suitable size, having independent compartment forinsulated Aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 3.00 mm thick CRCA sheetsuitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with aluminium bus bar of200 Amp rating for 3 phase and neutal4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, Cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coatingin siemens grey colourfront & rear opening type with double door shutter and locking arrangement, suitable aprons for cable entry/exist , including cable connection properly with lugs and thimable, complete all as specified and directed by Engr - In- Charge andcomprising as under: - |
| 8 | Incoming :- (a) MCCB 4 Pole, current rating 100 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz, - 01 Nos.(b)Digital voltwith selector switch.-01 set. (c)DigitalAmp meter with selector switch.-01 set. Out going :- (a)MCCB 4 Pole, current rating 63 Amp, With Thermal Magnetic release, breaking capacity 16 kA at 415V, 50Hz - 01 No(b) MCB SPNcurrent rating 40 Amp, breaking capacity 10 kA at 230 V, 50Hz - 02 Nos(c) MCB SPNcurrent rating 32 Amp, breaking capacity 10 kA at 230 V, 50Hz - 03 Nos(d) Angle iron base frame as reqd size as per above panel, total leg height 600 mm and grouting in side PCC 150 mm legsand made out of ISA 5050, 50 x 50 x 6 mm thick angle iron duly painted - 01 No.(e) M & L for necessary excavation and as reqd PCC 1:3:6 (40 mm graded aggregate) Type C2 for foundation of angle iron legs frame work complete - 01 Job |
| 9 | Excavation in trenches not exceeding 1.5m width and not exceeding 1.5 m in depth and getting out in soft/loose soil for taking up/laying cable/pipe etc complete all as specified and directed. |
| 10 | Returning , filling in trenches, including spreading , levelling , watering and well ramming in layers not exceeding 25 cm in Soft/loose soil complete all as specified and directed. |
| 11 | Removal of excavated material at a distance notexc 50 mtr and dipositing where directed at a level not exc. 1.5 mtr above the starting pointin Soft / loose soil complete all as specified and directed. |
| 12 | Supply and layingdry Sand cushioning to underground cable with screened, washed river sand, including punning gently complete all as specified and directed.Note: - Thickness after punning will be measured for payment. |
| 13 | Supply and layingfor burnt brick old size sub class \"B\" laid in trenches a butting each other with a gap not exceeding 10 mm , vertically over the cable for cable protection complete all as specified and directed. |
| 14 | Supply and layand testing cable LT XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with standerd aluminum conductor, 1100 Volts grade, of size70 Sqmm 3.5 Core complete all as specified and directed.Note:-Excavation, earthwork, will be measured and paid separately under respective items of this Schedule.. |
| 15 | Supply and layand testing cable LT XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with standerd aluminum conductor, 1100 Volts grade, of size120 Sqmm 3.5 Core complete all as specified and directed.Note:-Excavation, earthwork, will be measured and paid separately under respective items of this Schedule. |
| 16 | M & Lin replacement of Earthing complete in repairs with galvanised steel earthelectrode 60 cm x 60 cm x 6 mm burried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level connected to and including galvanised earth leadas eGI strip of 32X6mm dia by means of bolts,nuts, check nuts and washer etc made of galvanised iron and connected to earthing test point all as shown in electrical plate No.3 of SSR Part I 2009 and as specified or indicated and testing on completion including excavation/earth work in any type of strata, PCC (1:3:6) type C1 earthing chamber, precast RCC slab 50 mm thick in reinforced cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric (XPM jali weight not less than 4 Kg/Sqm), cast iron frame, funnel with wire mesh, 40 mm bore medium grade GI watering pipe, lugs, 15 mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed.Note: (i)Item includes the cost of 7.5 metre GI pipe for protection of earth lead. Any addition in length shall be adjusted through deviation order.(ii) necessary excavation wk is included in this item. |
| 17 | M & L of chemical Earthing complete with copper earth plate 90 cm x 60 cm x 5 mm burried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level connected to and including copper earth strip of 32X6mm dia by means of bolts,nuts, check nuts and washer etc made of galvanised iron and connected to earthing test point all as shown in electrical plate No.3 of SSR Part I 2009 and as specified or indicated and testing on completion including excavation/earth work in any type of strata, PCC (1:3:6) type C1 earthing chamber, precast RCC slab 50 mm thick in reinforced cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric (XPM jali weight not less than 4 Kg/Sqm), cast iron frame, funnel with wire mesh, 40 mm bore medium grade GI watering pipe, lugs, 15 mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed.Note: (i)Item includes the cost of 7.5 metre GI pipe for protection of earth lead. Any addition in length shall be adjusted through deviation order. |
| 18 | Supply and fix copper strip of size 32 x 6 mm with saddles and fixing screws etc for earthing connection to bus bar trunking system of existing LT Panels completed all as specified and directed. |
| 19 | Supply and fix copper strip of size 20 x 3 mm with saddles and fixing screws etc for earthing connection to bus bar trunking system of existing LT Panels completed all as specified and directed. |
| 20 | Supply and fix Earth marker Oval type made of Galvanized Iron,painting/marking with approved colour alongwith PCC foundation of suitable size complete all as specified and directed by Engr - In- Charge. |
| 21 | Supply and fix Earth marker Triangle type made of Galvanized Iron,painting/marking with approved colour alongwith PCC foundation of suitable size complete all as specified and directed by Engr - In- Charge. |
| 22 | Supply and fix Earth marker Rectangular type made of Galvanized Iron,painting/marking with approved colour alongwith PCC foundation of suitable size complete all as specified and directed by Engr - In- Charge. |
| 23 | M & L for Earthing complete with copper earthelectrode 60 cm x 60 cm x 3 mm burried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level connected to and including galvanised earth leadas copper strip of 20X3mm dia by means of bolts,nuts, check nuts and washer etc made of copper and connected to earthing test point all as shown in electrical plate No.3 of SSR Part I 2009 and as specified or indicated and testing on completion including excavation/earth work in any type of strata, PCC (1:3:6) type C1 earthing chamber, precast RCC slab 50 mm thick in reinforced cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric (XPM jali weight not less than 4 Kg/Sqm), cast iron frame, funnel with wire mesh, 40 mm bore medium grade GI watering pipe, lugs, 15 mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed.Note: (i)Item includes the cost of 7.5 metre GI pipe for protection of earth lead. Any addition in length shall be adjusted through deviation order.(ii) necessary excavation wk is included in this item. |
| 24 | Supply and fixing LED strip light 5 Mtr long, 240 LED, 5A230/12 V including all electrical connections complete all as specified and directed by Engr in Charge. |
| 25 | Supply and fixing LED Driver 230/12V, 33A including all electrical connections complete all as specified and directed by Engr in Charge. |
| 26 | Supply and fixing LED Driver 230/12V, 25A including all electrical connections complete all as specified and directed by Engr in Charge. |
| 27 | Supply and fixing LED Driver 230/12V, 16Aincluding all electrical connections complete all as specified and directed by Engr in Charge. |
| 28 | Supply and fixing LED strip filling Alluminium Channel 2 mtr long complete all as specified and directed by Engr in Charge |
| 29 | Supply and fixingone sqmm single core multistranded copper cable complete all as specified and directed by Engr in Charge. |
| 30 | Supply and fix LED Bulb 15 watt (Warm White) complete all as specified and directed by Engr in charge. |
| 31 | S&Fbush and spike LED light luminaire 12 W (warm white)having IP-65 protection, with minimum system efficency> 85%made of pressure die cast aluminium housing toughened glass in the front and peanut lens for batwing light distribution with excellent thermal management. The filling should have rated CCT 5000K complete with all accessories complete all as specified and directed by Engineer in Charge. |
| 32 | Supply and fixing HL-43 Linten 199 N shaped hanging light complete all as specified and directed by Engr in charge. |
