|
| 1 | श्शौचालय, सेप्टिक टैंक एवं बोरिंग आदि का कार्य |
| 2 | Excavation in foundation in ordinary soil (loamclay or sand) including lift up to 1.5m and lead up to 30m. And including filling watering and ramming of excavated earth into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth ad directed by the Engineer in charge up to a distance of 30m from the foundation trenches including all T&P phowarah and basket etc. complete. [PWD SOR 2020 -251) |
| 3 | Earth work in cutting or in embankment in ordinary soil excavation to be the from of regular pits not exceeding 1/2 meter (20\"\") in depth and earth work in enbankment to be in 20cm (8\"\") layers , including ramming and dressing the surface to requied levels and slopes and also including 1.5m (5\") lift and 30m (100\") lead.the earth from cutting to be used in making embankent or to be deposited as spoil banks within 30m (100\") distance as directed by the E/I and cartage of 5km. including loading and unloading. [SOR 2020, SI No. 253+231(a)] |
| 4 | Concrete with 4 cm.gauge stone ballast, coarse sand and cement in the proportion of 8:4:1 including supply of all materials labour and tools and plants etc. required for proper completion for the work. [SOR 2020, SI No. 281] |
| 5 | Cement Concrete with 2 cm. gauge apporved stone ballast, apporve coarse sand and cemnet in the proportion of 4:2:1 including supply of all materials labour and tools and plants etc. required for proper completion for the work. [SOR 2020, SI No. 279(b)] |
| 6 | RCC work with cement, coarse sand and 2 cm gauge stone grit in the proportion of 1:1.5:3 in Lighter beams excluding its fixing and binding the same with 24 BW GGl binding wire and including necessary centering and shuttering etc and also including supply of all materials required for proper completion of the work. Binding wire tobe supplied by the contractor free of cost. [SOR 2020, SI No. 285(b)] |
| 7 | M-150 brick work in 1:4 cement and coarse sand of 1.25 fineness modulous mortar in foundation and plinth including supply of all material, labour and tools and plants etc. required for proper completion of work. [PWD SOR 2020-305(b)] |
| 8 | 2.5 cm thick damp proof course with cement, coarse sand and 2 cm gauge stone grit in proportion in 1:1.5:3 with and including water proofing material as directed by E/I includingincluding supply of all materials labour and tools and plants etc. required for proper completion for the work. [SOR 2020, SI No. 361] |
| 9 | M-150 brick work in 1:4 cement and Coarse sand mortar in Super structure including necessary cutting and moulding of bricks required and for one brick thick wall including supply of all material, labour and tools and plants. Etc. required for proper completion of work. [SOR-2020, SINo. 305(b)+309+310] |
| 10 | Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 In exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement: 6 coarse sand). (DSR-2023 SI No.-6.28.2) above plinth level utpo floor Vlevel |
| 11 | RCC work with cement, coarse sand and 2cm gauge stone grit in the proportion of 1:1.5:3 in T-Beam and slab excluding its fixing and binding the same with 24 BWGGl binding wire and including necessary centering and shuttering etc and also including supply of all materials required for proper completion of the work. Binding wire tobe supplied by the contractor free of cost. [SOR 2020, SI No. 288(b)] |
| 12 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.(DSR 2023 SI NO 10.25.2) |
| 13 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated Jor L hooks, bolts and nuts & mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overtapping of sheets complete (up to any pitch in horizontal vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cufting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m (DSR 2023 SI NO 12.1.1) |
| 14 | Mild steel or iron in plain work such as in reinforced concreted or reinforced brick work (when not included in overall rates) wrough to required shape as necessary includind bending for proper completion of the work and including supply of steel its wastage. Bend hooks and authorized overlapping shall be measured. [SOR 2020, SI No. 504] |
| 15 | 12mm thick plaster with cement mortar consisting of 1 part cement and 4 part of coarse sand minimum thickness no be less than 10mm including supply of all materials, labour and T&P etc. required for proper completion of the work. [Based on SOR 2020, SI No. 584] |
| 16 | supply and fixing of 90 mm dia pvc pipe for each block (MR) |
| 17 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore(DSR- 2023,18.50.) |
| 18 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore(DSR- 2020,18.52.1) |
| 19 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore(SOR- 2020,18.53.1) |
| 20 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall(sor 2020, SI No.18.7) |
| 21 | 20 mm nominal outer dia Pipes |
| 22 | 25mm nominal outer dia Pipes |
| 23 | 15 mm nominal outer dia Pipes |
| 24 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :(SOR- 2020,18.17) |
| 25 | 25 mm nominal bore18.17.1 |
| 26 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :(SOR- 2020,18.18) |
| 27 | 20 mm nominal bore 18.18.3 |
| 28 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.(DSR-2023,12.22) |
| 29 | 110mm |
| 30 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (±0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (±0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (±0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).DSR 2023 SI No.9.118.1 |
| 31 | Providing and fixing 250 x 16 mm size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete . [DSR 2023, SI No. 9.96.2] |
| 32 | Providing and fixing of 200 x10 mm sizealuminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. [DSR 2023, SI No. 9.97.3] |
| 33 | Providing and fixing of 125 mm size aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete [DSR 2023, SI No. 9.100.1] |
| 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.[DSR 2023, SI. No. 13.80] |
| 35 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 Litter/10 sqm). [DSR 2023, SI. No. 13.47.1] |
| 36 | Wall painting two coats with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. [DSR 2023-13.83.2] |
| 37 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 600 mm (DSR2023 SI NO 11.41A.3.1) |
| 38 | Providing fixxing water closet squatting pan (indian type WC pan) with 100mm sand cast iron p or s trap. 10 liter low level with PVC flusing cistern including flush pipe with manually controlled device(handle lever) confarming to IS: 7231 with all fitting and fixtures complete inluding cutting and making good the wall and floers wherever requerd . White vitrous china orissa pattern WC pan of size 580*440 mm with intarnal type foot rest .SOR 2020 IT.17.1 |
| 39 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support Including fittings & fixtures for tank shall be paid separately. (DSR-2023, Sh.No.18.48A)) |
| 40 | Electric work |
| 41 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with .5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(DSR E&M 2022 1.10.3) |
| 42 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required .(DSR E&M 2022 1.14.2) |
| 43 | S&F surface/flush mounting 4 ways SPN distribution board without MCB complete in all respect,as directed at site by Engineer in charge. Cat-A.[Elect. SOR 2018, SI No. 1022] |
| 44 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commisioning etc. as required(DSR E&M 2022 2.10.1)) |
| 45 | Boring work |
| 46 | Boring/drilling bore well of requiured dia. For casing/strainer pipe, by suitable method prescribed in IS:2800 (part 1), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire and running charges of all equipments, tools, plants and machineries required for the job, all complete as per direction of Engineer-In-charge, upto 90m depth below ground level. All type of soil. 300mm dia.(DSR-2023,23.1.1.1) |
| 47 | Supply, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:12818, including required hire and labour charges, fittings and accesories etc. all complete, for all depths as per direction of Engineer-In-charge. 100mm nominal size dia.(DSR-2023,23.3.1/397) |
| 48 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire and labour charges, fitting and accesories etc. All complete for all depths, as per direction of Engineer-In-charge. 100mm nominal size dia. (DSR-2023,23.4.1/398) |
| 49 | Gravel packing in tube well construction in accordance with IS:4097, including providing gravel fine/medium/coarse, in required grading and sizes as per actual requirement, all complete as per direction of Engineer-In-charge, (DSR-2023,23.8/398) |
| 50 | Development of tube well in accordance with IS:2800 (part-1) and IS:11189, to establised maximum rate of useable water yiel without sand content (beyond permissible limit), with required capacity air compressor for required time till well is fully developed, measuring yiel of well by \"V\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well all complete including hire and labour charges of air compressor, tools and accesories etc. all as per requirement and direction of Engineer-In-charge. (DSR-2023,23.12/399) |
| 51 | Provinding and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement, all complete for bore well of 100mm dia. (DSR-2023,23.13.`/399) |
| 52 | Providing and fixing M.S. Clamp of required dia to the top of casing/housing pipe of tube well as per IS:2800 (part 1), including necessary boilt and nuts of requires size complete. 100mm clamp (DSR-2023,23.14.1/399) |
| 53 | Providing and fixing Bail plug/Bottom plug of reqired dia to the bottom of pipe assembly of tubewell as per IS:2800 (part 1) (DSR-2023,23.15.1/399) |
| 54 | Providing and Installation of 1 H.P. /0.75 K.W. submersible pump including 2.5 Sq.mm three core Cable, 100mm dia Reliance Pipe 100m, starter for motor etc. complete.(CMR) |
| 55 | providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.(DSR 2023 si no 18.45 ) |
| 56 | श्चेजिंग रूम, स्टोन फ्लोरिग व विद्युतिकरणआदि का कार्य |
| 57 | Excavation in foundation in ordinary soil (loamclay or sand) including lift up to 1.5m and lead up to 30m. And including filling watering and ramming of excavated earth into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth ad directed by the Engineer in charge up to a distance of 30m from the foundation trenches including all T&P phowarah and basket etc. complete. [PWD SOR 2020 -251) |
| 58 | Earth workin cutting or in embankment in ordinary soil excavation to be the from of regular pits not exceeding 1/2 meter (20\"\") in depth and earth work in enbankment to be in 20cm (8\"\") layers , including ramming and dressing the surface to requied levels and slopes and also including 1.5m (5\") lift and 30m (100\") lead.the earth from cutting to be used in making embankent or to be deposited as spoil banks within 30m (100\") distance as directed by the E/I and cartage of 5km. including loading and unloading. [SOR 2020, SI No. 253+231(a)] |
| 59 | Concrete with 4 cm.gauge stone ballast, coarse sand and cement in the proportion of 8:4:1 including supply of all materials labour and tools and plants etc. required for proper completion for the work. [SOR 2020, SI No. 281] |
| 60 | RCC work with cement, coarse sand and 2 cm gauge stone grit in the proportion of 1:1.5:3 in Lighter beams excluding its fixing and binding the same with 24 BW GGl binding wire and including necessary centering and shuttering etc and also including supply of all materials required for proper completion of the work. Binding wire tobe supplied by the contractor free of cost. [SOR 2020, SI No. 285(b)] |
| 61 | M-150 brick work in 1:4 cement and coarse sand of 1.25 fineness modulous mortar in foundation and plinth including supply of all material, labour and tools and plants etc. required for proper completion of work. [PWD SOR 2020-305(b)] |
| 62 | 2.5 cm thick damp proof course with cement, coarse sand and 2 cm gauge stone grit in proportion in 1:1.5:3 with and including water proofing material as directed by E/I includingincluding supply of all materials labour and tools and plants etc. required for proper completion for the work. [SOR 2020, SI No. 361] |
| 63 | M-150 brick work in 1:4 cement and Coarse sand mortar in Super structure including necessary cutting and moulding of bricks required and for one brick thick wall including supply of all material, labour and tools and plants. Etc. required for proper completion of work. [SOR-2020, SINo. 305(b)+309+310] |
| 64 | Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 In exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement: 6 coarse sand). (DSR-2023 SI No.-6.28.2) above plinth level utpo floor Vlevel |
| 65 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.(DSR 2023 SI NO 10.25.2) |
| 66 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated Jor L hooks, bolts and nuts & mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overtapping of sheets complete (up to any pitch in horizontal vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cufting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m (DSR 2023 SI NO 12.1.1) |
| 67 | RCC work with cement, coarse sand and 2cm gauge stone grit in the proportion of 1:1.5:3 in T-Beam and slab excluding its fixing and binding the same with 24 BWGGl binding wire and including necessary centering and shuttering etc and also including supply of all materials required for proper completion of the work. Binding wire tobe supplied by the contractor free of cost. [SOR 2020, SI No. 288(b)] |
| 68 | Mild steel or iron in plain work such as in reinforced concreted or reinforced brick work (when not included in overall rates) wrough to required shape as necessary includind bending for proper completion of the work and including supply of steel its wastage. Bend hooks and authorized overlapping shall be measured. [SOR 2020, SI No. 504] |
| 69 | 12mm thick plaster with cement mortar consisting of 1 part cement and 4 part of coarse sand minimum thickness no be less than 10mm including supply of all materials, labour and T&P etc. required for proper completion of the work. [Based on SOR 2020, SI No. 584] |
| 70 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (±0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (±0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (±0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).DSR 2023 SI No.9.118.1 |
| 71 | Providing and fixing 250 x 16 mm size aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete . [DSR 2023, SI No. 9.96.2] |
| 72 | Providing and fixing of 200 x10 mm sizealuminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. [DSR 2023, SI No. 9.97.3] |
| 73 | Providing and fixing of 125 mm size aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete [DSR 2023, SI No. 9.100.1] |
| 74 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.[DSR 2023, SI. No. 13.80] |
| 75 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ .90 litter /10 sqm). [DSR 2023, SI. No. 13.47.1] |
| 76 | Wall painting two coats with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. [DSR 2023-13.83.2] |
| 77 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 600 mm (DSR2023 SI NO 11.41A.3.1) |
| 78 | P/F of 65 mm (+/- 2 mm) thick Chaunar sand stone flooring over 20 mm (average) th . Base of cement mortar 1:5 (1Cement:Coarrse sand ) with joints 3mm th side buttered with cement mortar 1:2 (1cement : 2 Stone Dust) adnixed with pigment to match the shade of stone and pointing with same mortar sand stone.(previous approved by vda) |
| 79 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support Including fittings & fixtures for tank shall be paid separately. (DSR-2023, Sh.No.18.48A)) |
| 80 | Electrical work |
| 81 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with .5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(DSR E&M 2022 1.10.3) |
| 82 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required .(DSR E&M 2022 1.14.2) |
| 83 | S&F surface/flush mounting 4 ways SPN distribution board without MCB complete in all respect,as directed at site by Engineer in charge. Cat-A.[Elect. SOR 2018, SI No. 1022] |
| 84 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commisioning etc. as required(DSR E&M 2022 2.10.1)) |
| 85 | Street Light |
| 86 | S&F of 63 Amp. 415 V metal clad T.P. reqireable type switch fuse unit on angle iron bracket complete in all respectCAB - BSOR 2018 SI No. 312 |
| 87 | Wiring wire 1.5 sqmm 2 core.PSR at Rajghat Bridge file |
| 88 | S/B of pole earthing with 20mm die × 2000mm long M/S Rod connected with pole by 6 to 4 swg GI wire complete.As per UPPCL |
| 89 | S/F of 7 mtr. GI octagonal pole of approved make (top dia 70mm, bottom dia 130mm and base plate 12mm thick) having 3mm thickness with single arm bracket (1 mtr. Length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and required T&P complete in all respect.SOR 2018 SI No. 641 |
| 90 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc6sqmm × 3 coreSOR 2018 SI No. 501 (e) |
| 91 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respectCAT - AASOR 2018 SI No. 1424 |
