Tender For Renovation Of Existing Sentry Post, Existing Exit/Entrance Main Gate & Wicket Iron Gate, Damaged Boundary Wall, Raising Height Of Existing Boundary Wall, Construction Of Two Watch Towers Of Milkman Colony And A Pathway Along The Boundary Wall Inside Campus At Ocr Jodhpur Under Ge (A) No. 02; 1 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense of soil complete all as specified and directed by Engr-in-charge. 2 Excavating in trenches, n exc 1.5 Mtrwide and n exc 1.5 Mtr in depth; forfoundation, etc. or for shafts, wells,cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 Mtr indepth and getting out in hard & dense soil complete all as specified and directed by Engr-in-charge. 3 Ditto-all as per item no 2 but exc 1.5Mtr and n.exc 3Mtr depth of excavationand getting out in hard & dense soil complete all as specified and directed by Engr-in-charge. 4 M&l for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundations fillings & mass concrete complete all as specified and directed by Engr-in-charge. 5 M&L forproviding RCC M25 Design mix ( using 20 mm graded aggregate) as in foundations, including rafts, footings,foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-charge. 6 M&L forproviding RCC M25 Design mix( using 20 mm graded aggregate) as inColumns,pillars, piers, posts and strutscomplete all as specified and directed by Engr-in-charge. 7 M&L forproviding RCC M25 Design mix( using 20 mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-charge. 8 M&L forproviding RCC M25 Design mix( using 20 mm graded aggregate) as in Chajjas etc complete all as specified and directed by Engr-in-charge. 9 M&L forproviding RCC M25 Design mix( using 20 mm graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed by Engr-in-charge. 10 Use & waste of Formwork to concrete sides and soffit of concrete foundations, footings, bases of columns, raft and raft beams of foundation , plinth beams and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed by Engr-in-charge. 11 Use & waste of Formwork to sides of square/rectangular or polygonal pillars, posts, struts, piers,columns and stanchions for rough finished surfaces complete all as specified and directed by Engr-in-charge. 12 Use & waste of Formwork to sides and soffits of floor or roof beams, beam , lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces compleate all as specified and directed by Engr-in-charge. 13 Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces complete all as specified and directed by Engr-in-charge. 14 Use & waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces complete all as specified and directed by Engr-in-charge. 15 M&L for mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge. 16 M&L for mild steel TMTbars 5mm dia and over upto and including 10mm dia asin stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge. 17 M&L for squared rubble walling Jodhpur type brought upto course well bonded, bedded and solidly hearted built in cement mortar (1:6) complete all as specified and directed by Engr-in-charge. 18 Extra over of hammer dressing to face stone with maximum depression on face from straight edge not exc 20mm and dressing face bed and joints as specified to squared rubble walling jodhpur type brought upto cources as directed complete all as specified and directed by Engr-in-charge. 19 Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-charge. 20 M&L for brick work with Fly ash old size ‘bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6. complete all as specified and directed by Engr-in-charge. 21 M&L for Brickwork with Fly ash old size ‘bricks straight or curved on plan to any radius inhalf brick thick walls built in CM 1:4 complete all as specified and directed by Engr-in-charge. 22 M&L for 40mm thick cement concrete 1:2:4 Type B0(using 12.5 mmgraded stoneaggreagate) as in damp proof coursewith WPC to vertical or horizondal surface including necessary form work complete all as specified and directed by Engr-in-charge. 23 M&L 15mm thick rendering consist of 2 layer , first layer 10mm thick in CM 1:6 and outer layer of 5mm thick in cm 1:4on fair faces of brick or concrete surfacesfinishedeven and fairwith WPC 0.20 lts per bag ofcement used on roof , chhajja complete all as specified and directed by Engr-in-charge. 24 M&L15mm thick rendering in CM 1:6 on fair facesof brick/concrete surface finished even and smooth with out using extra cementcomplete all as specified and directed by Engr-in-charge. 25 M&L 5mm thick renderingin CM 1:3 on ceilingof concrete surface finished even and smooth without using extra cement etc. complete all as specified and directed by Engr-in-charge. 26 M&L15mm thick rendering in CM 1:4 on fair facesof concrete surface finished even and fair complete all as specified and directed by Engr-in-charge. 27 M&L for preparing new plastered surface of wall and applying two coats of weather proof exterior grade emulsion paint over and including a coat of cement based primer, complete all as specified and directed. By Engr-in-charge. 28 M&Lfor preparing newly plastered surfaces of wall and applying two coats of oil bound distemper overa coat of primer including 2mm thick putty to make the surface to be plain and smooth complete all as specified and directed by Engr-in-charge. 29 M&Lfor preparing newly plastered surfaces of walland applying three coats of white wash complete all as specified and directed by Engr-in-charge 30 M&Lfor preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engr-in-charge. 31 Removing excavated material exc. 250m but n.exc 500m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-charge. 32 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed by Engr-in-charge. 33 M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed by Engr-in-charge. 34 M&L for broken stone Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-charge. 35 M&Lfor 75 mm thickPCC 1:4:8 type D2 using 40 mm graded stone aggreagateas in sub base of flooring/path/hard standing complete all as specified and directed by Engr-in-charge. 36 M&L for cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth .complete all as specified and directed by Engr-in-charge. 37 M&L for joint free non skid ceramic coloured tiles, of size 600x600x7 to8 mm thick (square/rectangular), in floors etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed by the Engineer -in-charge. 38 Ditto all as per item No 37 but as in skirtingand set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM (1:6) complete all as specified and as directed by the Engineer -in-charge. 39 M&L for non skid ceramic color tiles of size300x300x7 to8 mm thick ( square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed by the Engineer -in-charge. 40 M&L for glazed ceramic coloured tilesof size 300x 450x 7 to 8 mm thick on vertical surface such as in dado over 10 mm thick rendering inCM (1:4) complete all as specified and directed by Engr-in-charge. 41 S&F viterous china Pedestral typepattern EWCwhite with P or Strap front or back inlet ( excluding flushing cistern and flush pipe) including PVC Sheet cover and provision of cement concrete bedding and making good surfaces complete all as directed. as specified by Engr-in-charg. 42 S&F PVC low level flushing cistern 10 lts capacity with ball valve float and handle ,syphonic action type including brackets and flush pipe of polythelene of low or high density or PVC 32 mm dia low level flushing cistern fixed in repairs all as specified and directed by Engr-in-charge. 43 S&F vitreous china wash hand basin ,white, flat back, size 550x400 mm including 32mm low density Waste pipe(600mm long)chain and plug and porcelain stopper, brackets including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-charge. 44 S&F PVC connection 15mm bore with PTMT nuts and 450 mm long complete all as specified and directed by Engr-in-charge. 45 S&F for tubular towel rail 20 mm dia 600 mm long brass CP including brackets fixedcomplete all as specified and directed by Engr-in-charge. 46 S&F forPVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm, complete all as specified and directed by Engr-in-charge. 47 S&Flong body bib taps, 15 mm dia fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-charge. 48 S&F 15 mm dia pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated fancy typescrewed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge. 49 S&F for 15 mm stop/angle cock ofchromium plated fancy typecopper alloyscrewed down high pressurefor iron pipe or for unions fixed complete all as specified by Engr-in-charge. 50 S&Fin repairfor Brass CP with long shank and cup (concealed type screwed down, high presure capstan head handle for iron pipe and fixed with wall flange ISI marked complete all as specified and as directed by Engr-in-charge. 51 S&Fforoverhead shower 150x150 mm of ABS body crome plated with gray face plate with arm having swivel joint chromium plated complete all as specified and as directed by Engr-in-charge. 52 S&F forhealth faucet with 1.25m long flexible mild steel chromium plated tube 15 mm dia with wall hook complete all as specified anddirected by Engr-in-charge. 53 S&F chromium plated Brass grating100 mm dia complete all as specified and directed by Engr-in-charge. 54 S&F PVC floor/nahani trap 75 mm dia with grating including jointing to wastepipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed by Engr-in-charge. 55 S&F rotational moulded polyethylenecylindrical vertical withclosed top water storagetanktriple layered white colour 1000 ltr capacity with connectingnipple, hoisted and fixed in position on new or existingfoudation and making GI tubing inlet or outlet connection complete all as specified anddirected by Engr-in-charge. 56 S&F rotational moulded polyethylenecylindrical vertical withclosed top water storagetanktriple layered white colour 500 ltr capacity with connectingnipple, hoisted and fixed in position on new or existingfoudation and making GI tubing inlet or outlet connection complete all as specified and directed by Engr-in-charge. 57 S&F 20mm outer bore CPVC pipes SDR 11 with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge. 58 S&F 16mm outer bore CPVC pipes SDR 11 with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-charge. 59 S & F 15 mm bore Galvanized Steel tubes, medium gradefixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings complete all as specified and directed by Engr-in-charge. 60 S & F 20 mm bore Galvanized Steel tubes, medium gradefixed to walls and ceilings or laid in floors,concealed or open incl cutting of grooves including taking up or down with connections and fittings complete all as specified and directed by Engr-in-charge. 61 S&F 20 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-charge. 62 S & F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.Minimum weight2 0 m m - 2 1 0 g m s complete all as specified and directed by Engr-in-charge. 63 S & F 75 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in walls complete all as specified and directed by Engr-in-charge. 64 S &F 75 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engr-in-charge. 65 S &F 110 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in walls complete all as specified and directed by Engr-in-charge. 66 S& F 110 mm PVC SWR pipe single socketed in any length with rubber ring joints laid in trenches or in floors .complete all as specified and directed by Engr-in-charge. 67 S F 75 mm diaPVC (SWR)bendsany radius complete all as specified and directed by Engr-in-charge. 68 S& F 110 mm diaPVC (SWR)bendsany radius complete all as specified and directed by Engr-in-charge. 69 S&F 125/110 mm PVC (SWR) gully trap, setting and jointing with solvent cement complete all as specified and directed by Engr-in-charge. 70 S&FStack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof. complete all as specified and directed by Engr-in-charge for 100mm dia pipe. 71 M&L for MS work as in grills and similar work confirming to Fe 290, gde-E-165 complete all as specified and directed by Engr-in-charge. 72 M&L for MS frame workas in ladder of angle or other section with railing bracers etc conforming to Fe-290 Gde E-165 and fixed complete all as specified and directed by Engr-in-charge. 73 S&F 5.5 mm thick coloured sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-charge. 74 S & F 5mm thick pin headedglass, ordinary quality and glazing with oil putty in square n.exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-charge. 75 S & F forStainless steel wire cloth.0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed by Engr-in-charge. 76 M&L for25 mm thick Sand stone slabs in plinth protection ofn exc. 2m in length and n.less than750mm wide punched dressed on face and along exposed edges, self faced on other side andover and including 15mm thick screed bed in CM 1:6as in plinth protection , set and pointedincement mortar 1:4 and edges of50 mm thick, finished with using PCC 1:2:4 Type B1complete all as specified and directed by Engr-in-charge. 77 M&L for Green marble 18/20 mm thick in steps, pillars, wndow cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engr-in-charge. 78 M&L for Machine pressed precast concrete interlocking paver block rubberisedany shape and size with white cement cement andpigment comfirming to IS 658-2006 of60mm thick M-35 grade complete all as specified and directed by Engr-in-charge. 79 M&L sand filling under path as cushioning to interlockingincluding watering and consolidation complete all as specified and directed by Engr-in-charge. 80 M&L for Cement concrete Type B1 1:2:4 (20 mm graded aggregate) as in stops, coping etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-charge. 81 M&L for cement concrete 1:4:8 type D-2 (Nominal mix) using 20 mm graded crushed stone aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 180 mm bore pipes complete all as specified and directed by Engr-in-charge. 82 M&L for DWCPE(SN8) 180mm(OD) /163 (ID)mm bore of pipelaid and jointed on concrete bed 150mm thick , complete including testing etc. all as specified. (Concrete bed shall be measured and paid for separately).complete all as specified and directed by Engr-in-charge. 83 Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x5 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.00 sqm) comprising of uPVC multi chamberedrame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (stainless steel butt hinges and necessary S S screws, 6 mm Glass or wiremesh incl in this item).Note: For PVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. inepth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 84 Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For PVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 85 S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed. by Engr-in-charge. 86 S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 87 S&F forfactory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter ( 2,4,6 raised panel design on the front side and back side plain) of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engr-in-charge.Note: stainless steel (100mm butt hinges- 03, 150mm tower bolt-02, 300mm Sliding door bolt - 01, 150mm handle -02 and necessary S.S screws shall be including) 88 S& F for30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and directed by Engr-in-charge.Note: stainless steel (100mm butt hinges- 03, 150mm tower bolt-02, 300mm Sliding door bolt - 01, 150mm handle -02 and necessary S.S screws shall be including) 89 S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick prelaminatedcolour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-charge. 90 S &F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelaminatedcolour PVC sheet on back face with wood free EPS core including fixing in frame at site as per specification & drawing complete all as specified and directed by Engr-in-charge. 91 M&L Rendering 15mm thick cement mortar 1:4 shall be provided mixed with WPC @3% by weight of cement at green concrete complete all as specified and directed by Engr-in-charge.Note: WPC shall be measured and paid separately 92 Supply only Integral waterproofing compound complete all as specified & as directed by Engineer-in-Charge 93 M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabriclaid on primed surface of blown Bitumen of 1.2Kg per Sqm by torchingapplication and over including a coat of approved bituminous primer @ 0.40 liter per Sqmcomplete all as specified & directed by Engr-in-charge. 94 M&L for PCC 1:2:4 Type B-1 (using 20mm graded stone aggregate ) average 40mm thick ,finishingthe top concretesurface even andsmooth without using extra cementover APP membrane surfaceon roof / terrace.complete all as specified and directed by Engr-in-charge. 95 M&L for Provn of Soakage wells exc,in ordinary soil,foundation in PCC 1:3:6 ,wells of honey combed and solid in M-25 concrete,including intercepting chamber,screen chamber Brick work in CM,RCC cover slab in M-25/ Brickmasonary/Filling with brick bats ,complete of size (1.2 m dia x 3.0 M deep) complete all as specified and directed by Engr-in-charge. 96 Surface dressing n exc 30cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified & directed by Engr-in-charge. 97 Removing excavated material (soil)n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point. Complete all as specified and directed by Engr-in-charge. 98 M&L for squared rubble stone wallingJodhpur type,regular coursed,well bonded, bedded and solidly hearted,built in CM(1:6) complete all as specified and directed by Engr-in-charge. 99 Extra over stone masonry for hammer dressing to facestones with maximum depression on face from a straight edge held against the dressed surfaces not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type, regular coursed complete all as specified and directed by Engr-in-charge. 100 M & L for keyed pointing over square rubble stone walling, regular coursed jodhpur type built in CM (1:3). Complete all as specified and directed by Engr-in-charge. 101 M&L for work as in post and struts in fencing including cutting top to shape as directed railing holes notching for wire etc and similar work conforming to Fe-410-0 or Fe -310-0 comlete all as specified and directed by Engr-in-charge. 102 M&L for Mild steel screw bolts 11 to 15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed by Engr-in-charge. 103 Supply only for Chain link MS galvanized fencing, 50mm aperture size complete all as specified and directed by Engr-in-charge.Note:- A BOO shall be detailed by GE to as certain the per sqm weight of chain link fencing. 104 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by engr-in-charge. 105 M&L for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge. 106 M&L for preparing new steel surfaces of any description exceeding10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-charge. 107 S & F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts incl. securing or tying at crossing with and provision of galvanised mild steel wwire staples or steel pins etc complete all as specified and directed by Engr-in-charge. 108 S&F of GI concertina coil of dia 600 mm and shall be fixed complete all as specified and directed by Engr-in-charge. 109 M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engr-in-charge. 110 M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-charge. 111 Material and labour for point wiring (Modular) complete light/exhaust fancontrolled by one switch one way with 1.5 sq mm single core multi stranded copper conductor PVC FRLS insulated unsheathed 1100 Volt grade cable in and includingPVC FRLS CONCEALED CONDUIT PIPE (ISI Marked) of 20/25 mm bore with all accessories including new pressed steel terminal boxes (sunk in wall ) with 3.00 mm thick plastic laminated sheet top cover or PVC FRLS board including PVC FRLS top cover (suitable for modular switch & sockets etc .) with 1.50 sq mm insulated unsheathed PVC FRLS multistranded covered copper conductor for common earth and connecting to earth dolly and making good disturbed surface of wall incl matching the colour of wall/ceiling with extisting wall/ceiling colour complete all as specified and directed by engineer-in-charge. 112 All as per srl item no. 111 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board complete all as specified and directed by Engr-in-charge. 113 All as per srl item no. 111 here-in-before but for one socket outlet 3 pin, 5 Amps on same board complete all as specified and directed by Engr-in-charge. 114 All as per srl item No 111here-in-before but with 4 sq mmFRLS copper wire with 4 Sqmm FRLS copper earth wire for 3 pin socket 15 amp independent or other suitable pointcomplete all as specified and directed by Engr-in-Charge 115 All as per srl item no. 111 here-in-before but for one light point controlled by two 2-way switches complete all as specified and directed by Engr-in-charge. 116 Material & Labour Modular switch 6A one way complete all as specified and directed by engineer-in-charge. 117 S & FModular Socket, 6 A ,5 Pin,2 module size complete all as specified and directed by Engr-in-charge. 118 S & FModularswitch1way 16 A , 1module size complete all as specified and directed by Engr-in-charge. 119 S & FModularSocket , 6 A , 5 Pin , 2module size complete all as specified and directed by Engr-in-charge. 120 S & FModular Switch two way 6A , 1 module size complete all as specified and directed by Engr-in-charge. 121 S&F of Modular type regulator 2 module A/C 240 Volts complete all as specified and directed by Engr-in-charge.. 122 Supply and fixingCeiling rose on PVC FRLS board size 65 X 50 mm three terminal complete all as specified and directed by engineer-in-charge. 123 Supply and fixing LED light fitting mirror type with high output difffuser 2 feet ,10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by engineer-in-charge. 124 S&F LED light fitting 1 X 20 watt (4 feet),Batten Light, a slim design with internal driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal,complete all as specified and directed by engineer-in-charge. 125 S&F LED bulb of 9 /10 watt,6500K including PVC holder complete all as specified anddirected by Engineer-in-charge. 126 Supply and fixing LED street light fitting not less than 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-charge. Note:-The cost supplying and fixingiron bracket 32 mm bore with necessary nut bols ,clamp etcis included in quoted rate. 127 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mmcomplete all as specified and directed by engineer-in-charge. 128 Supply and fixing ceiling fans complete with blades, canopy,down rods upto 2 feet, including all accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by engineer-in-charge. 129 Supply & Fixing Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed by Engr-in-charge.Note : 1.Blank plates will be included on the quoted rates.2. All wires to be properly connected with copper lugs.3.MCB will be measured and paid separately. 130 Supply and fixing240V, 10 KA B curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioningcomplete all as specified and directed by engineer-in-charge. 131 Supply and fixing MCB SPN 32 Amp, C Curve 240 volts. complete all as specified and directed by engineer-in-charge. 132 M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed by engineer-in-charge. 133 Supply and fix desert cooler ,electric driven (single phase ),having nominal air flow capacity of 5000 Cum per hour (or nearest size ) steel body complete all as specified and directed by engineer-in-charge. 134 M&L for wall mounting stand for desert cooler made out of MS angle iron of size 40 mm x40 mm x6 mm thick suitable for nominal size of desert cooler including making good for disturbed surface ,welding works ,duly paint of one coat of red oxide primer and two coats of synthetic enamel paint all as shown on drawing No CEJZ/WD/98/TD-15/2017 sheet 1/1 complete all as specified and directed by engineer-in-charge. 135 Supply & laying steel Tubing galvanized medium grade (ISI Marked) 25 mmbore and tube fittings ISI marked laid in trenches /in road/on walls/in open including cutting existing pipeline for insertion of suitabe size tee for connectionetc allas specified and directed by Engineer-in-charge. 136 Supply & FixingGlob or Gate valve 25 mm bore, gun metal with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-charge. 137 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 corecomplete all as specified and directed by engineer-in-charge. 138 M&L for Cutting of road/hardstanding not more than 30 cm deep 45 cm widefor crossing of water pipe line in trenches and making the surface good with PCC(1:2:4) type B-1 using 20 mm graded aggregate complete in all respect as specified and directed by engineer-in-charge. 139 M&L Sand cushioning to undergound cable with using tibba sand and gently punning for cushioning to cable complete all as specified and as directed by Engineer-in-charge.Note: For the purpose of payment only punned thickness will be measured. 140 Supply & laying unreinforced precast concrete cable cover , Class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified & directed by Engineer-in-charge. 141 Supply & Laying steel tubing light grade galvanised 32 mm bore with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by engineer-in-charge.
