Tender For Construction Of Ring Well 6 Mtr. Dia With Laying Of Pipe From Ring Well To Existing Pipeline Network Including Pump House At Duke Nagar-Ii (Encroach Area) Under Sub Division No.Iii, Nacd, Apwd, Mayabunder
Tender Value
47.53 Lakhs
Estimated cost
Bid Submission
30 Oct 2025
0 days left
EMD
95067
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
mayabunder → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Ring Well 6 Mtr. Dia With Laying Of Pipe From Ring Well To Existing Pipeline Network Including Pump House At Duke Nagar-Ii (Encroach Area) Under Sub Division No.Iii, Nacd, Apwd, Mayabunder
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. |
| 2 | All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 4 | All kinds of soil. |
| 5 | Extra rates for quantities of works, executed: |
| 6 | In or under water and/or liquid mud, including pumping out water as required |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 8 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. |
| 9 | All kinds of soil |
| 10 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 11 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 12 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 13 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 14 | Providing and fixing up to floor fIve level precast cement concrete hollowblock,includinghoistingandsettinginpositionwith cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. |
| 15 | 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) . |
| 16 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 17 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 18 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 19 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : |
| 20 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu- ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 21 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 23 | Foundations, footings, bases of columns, etc. for mass concrete |
| 24 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 25 | Suspended floors, roofs, landings, balconies and access platform |
| 26 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 27 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 28 | Well steining |
| 29 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 30 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 31 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 32 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 33 | 150x10 mm |
| 34 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 35 | 100 mm |
| 36 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 37 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 38 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. |
| 39 | 80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 40 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 41 | Electric resistance or induction butt welded tubes |
| 42 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 43 | Providing and fixing bolts including nuts and washers complete. |
| 44 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 45 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 46 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 47 | 40 mm thick with 20 mm nominal size stone aggregate |
| 48 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. |
| 49 | 18 mm thick |
| 50 | Extra for providing and fixing wind ties of 40x 6 mm flat iron section. |
| 51 | 12 mm cement plaster of mix : |
| 52 | 1:4 (1 cement: 4 fine sand) |
| 53 | 12 mm cement plaster of mix : |
| 54 | 1:4 (1 cement: 4 coarse sand) |
| 55 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 56 | 1:4 (1 cement: 4 fine sand) |
| 57 | Distemperingwith 1stqualityacrylicdistemper (ready mixed)havingVOCcontentlessthan50gram/litre,of approved manufacturer, of required shade and colour all complete: |
| 58 | New work (two or more coats) over and including water thinnableprimingcoat withcement primerhavingVOC content less than50 pram/litre |
| 59 | Finishing walls with textured exterior paint of required shade : |
| 60 | New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 61 | Applying priming coat: |
| 62 | With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 63 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 64 | Two or more coats on new work |
| 65 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : |
| 66 | Two or more coats on new work |
| 67 | Supplying and stacking at site. |
| 68 | 90 mm to 45 mm size stone aggregate |
| 69 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work |
| 70 | 80 mm dia nominal bore |
| 71 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 72 | 80 mm nominal bore |
| 73 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : |
| 74 | 80 mm diameter pipe |
| 75 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 76 | 80 mm nominal bore |
| 77 | Supplying and filling in plinth with gravel in intake channel. |
| 78 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked black enamelled M.S butt hinges with necessary screws excluding, panelling which will be paid for separately. Superior Hardwood category- II (A)35mm thick shutters. |
| 79 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled ISI marked M.S butt hinges with necessary screws.Kiln seasoned and chemically treated superior hardwood cat-II (A).35 mm thick. |
| 80 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equalavent(size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 81 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets accessories 0.50 mm (+0.05 %) total coated thickness, with aluminium Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. |
| 82 | Ridges plain (500 - 600mm) |
| 83 | Providing cement concrete surface drainwith 1:3:6 (1-cement, 3-sand and 6-graded stone aggregate 40mm nominal size) finished with 1:4 (1-cement & 4-sand) including floating coat of neat cement inside the drain and its top & exposed surface including earth work inexcavation and disposal of surplus earth etc complete. |
| 84 | 15 x 15cm surface drain. |
| 85 | Providingandlayinginpositioncementconcrete 1:3:6 (1 cement : 2 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. |
| 86 | Supplying , Installation, testing and commissioningof Diesel driven pump set of Kirloskar make 28HP engine model No DM 28, 1800 RPM Vertical double Cylinder, water cooled four stroke cycle, self start direct compression injectioncoupled with Kirloskar make 26SR9 pump with CI impeller having a suction and delivery of 80mm/65mm with a minimum discharge of 12.2 LPS at a head of 80 mtrs including supplying and installation of base frame with foundation bolts and nuts , coupling assembly, coupling guard, foot valve, diesel tank etc as required. |
AI Tender Summary
Tender Timeline
Oct 22, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 30, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender