|
| 1 | Demolition of brick work or stone/ boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles complete all as specified and as directed. |
| 2 | Takingout cement plaster any description, from brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 3 | Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed |
| 4 | M & L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation complete all as specified and directed. |
| 5 | M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 complete all as specified and as directed. |
| 6 | M&L Brick work withOld bricks or brick tiles retired from demolition, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 complete all as specified and as directed. |
| 7 | M&L for brickwork with subclass \"B\" Bricks, straight or curved on plan on any radius in half brick thick walls built in CM 1:4 complete all as specified & directed by Engineer-in-charge. |
| 8 | M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with WPC as per required instruction and finished the surfaces even and smooth without using extra cement complete all as specified and as directed Note : WPC will be measured and paid for separately. |
| 9 | M&L for rendering 15mm thick in cement mortar (1:6) onsurfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified & directed. |
| 10 | Supply only integral water proofing compound as per latest IS specification complete all as specified. |
| 11 | M&L for returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and as directed. |
| 12 | Removing excavated surplus soil / material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed |
| 13 | M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tintover a coat of chalk whiting complete all as specified & directed. |
| 14 | M&L for preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint, complete all as specified & directed. |
| 15 | M&L for preparation of old decorated external surfaces of wall, fascia, vertical and horizontal surfaces of roof projection, chajja etc and applying one coat of weather coat (smooth classic, any colour as directed) with anti fungal exterior coating weather proof emulsion paint complete all as specified & directed. |
| 16 | Providing and applying plaster of paris of 1mm thickness over plastered surface to prepare the surface even and smooth |
| 17 | M&L for preparation of new plastered surface of walls/roof/floor and two coats of weather proof Acrylic emulsion paint (exterior grade) in camouflage pattern on wall, roof or floor incl necessary scafolding over one coat of weather primer complete all as specified and as directed by Engr- in- charge. |
| 18 | Taking down of chowkat or frames including shutter without taking off shutters from the frame area not exceeding 1.5 Sqm each removing from site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed. |
| 19 | All as per Serial item No. 18.00 here in above but exc 1.5 sqm not exc 4sqm |
| 20 | Taking down of shutters of any description not exceeding 1 Sqm each all as specified and as directed. |
| 21 | Taking down of shutters of any description exceeding1 Sqm each and not exceeding 2 Sqm each all as specified and as directed. |
| 22 | Re-fixing in same opening serviceable shutter after easing & necessary repairing of any description not exceeding 1.0 sqm each complete all as specfied and directed |
| 23 | Re-fixing in same opening serviceable shutter after easing & necessary rapairing of any description exceeding 1.0 sqm not exceeding 2.0 sqm each complete all as specfied and directed |
| 24 | Taking down aluminiumwindowframe with shutters (Without taking off shutters from frame) not exc 1.5 Sqm each complete all as specified and directed. |
| 25 | Taking down aluminiumdoor frame with shutters (Without taking off shutters from frame) exc 1.5 Sqmnot exc 4.00 sqm eachcompleteall as specified and directed. |
| 26 | Dismantlingsteel ofany description fixed to any type of fencing posts grating, jali etccomplete all as specified and as directed by Engineer-in-Charge. |
| 27 | Supply and fixing framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed |
| 28 | M&L for Mild Steel framed work for door chowkhats made out of angle iron Fe-290 (Gde E-165) including welding of hold fast and supply and fixing tie rod 10 mm dia round bars (01 Nos) welded at bottom and making holes for sliding/ tower bolt into angle iron/ brick work and make good disturbed surface in cement mortar (1:3) and provide adequate piece of conduit pipe 3 mm thick of suitable size welded with angle iron frame for holding sliding/bolt frame for holding sliding/tower bolt complete all as specified anddirected. |
| 29 | S&F Mild steel work as in band, straps, supports for RWP, clamps, hold fasts, wall ties, hooks & pintle hinges and similar small articles conformingto Fe-290-0 or Gde E-165 complete all as specified and as directed by Engineer-in-Charge |
| 30 | S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts mild steel Framed works such as in fencing posts/ struts in fencing including cutting top to shape as directed, drilling holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work confirming Fe 410-0 or Fe-310-0 all as specified and as directed. |
| 31 | S&F Joist, channel, angle or tee sections, fixed independently without connecting plates etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410- W (Gde- quality- B) |
| 32 | M&L TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 33 | S & F ofSteel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 |
| 34 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete,all as specified anddirected . |
| 35 | Provision of perforated/semi-perforated 10mm thick ceiling tiles/ board of size 595mm x 595mm for insulation and acoustic purposes including aluminium anodised section of size, wall angle 30mm x 25mm x 2mm thick, main / cross tee-section 15mm x 15mm x 1.4mm and suspended with 4mm dia GI wire of suitable lengthand includingfixed &aluminium snap grid all as per clause 10.38.1 of SSR Part-I and as per manufacturer’s instructions complete all as specified and as directed by Engineer-in-Charge.Make : Aluminium section - INDALCO/ HINDALCO/ JINDALPerforated/Semi Perforated TILES -ARMSTRONG/ LAFARG. |
| 36 | Dismantling timber scantlings 40 Sqcm and over in section, in any position |
| 37 | M&L for second class hardwood in scantlings timber unframed and fixed clean sawn a specified and as directed. |
| 38 | Dismantling boarding, any description, fixed in any position with nails |
| 39 | M&L for Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps of 2nd class hardwood planed both sides with butt joint fixed with nails to timber frame/roof member complete all as specified and directed. |
| 40 | Supply & Fixing 2nd class hard wood plain, soild straight chowkats and frames of wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed by Engineer-in-Charge |
| 41 | M&L for providing plain cement concrete 1:3:6 type C1 using 20mm graded aggregates for fixing hold fast and making good to disturbed surfacesall as specified and as directed. |
| 42 | S&F of 30mm thick flush door shutter solidcore construction with block board case and plywood face panels, commercial type on both sides make as approved by GE. |
| 43 | S & F of 2ndclasshardwood glazed and skeletonshutters 35 mm thick open rebated and prepared to receive glass, gauge etc with sash bar divided into Sqms edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass or gauze etc all as specified and as directed. |
| 44 | All as per serial item No 43.00 here-in-before but 30 mm thickas inwindow and ventilatoretcare provided with stiles and rails, sash bar all as specified in SSR Part I, section 8, clause 8.24 (b), chemically treated,complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F in repairs factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C\" channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete, all as specified & directed. |
| 46 | S&F in repairs solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel Squar tube with singal side prelam PVC sheet used instead of plain colour PVC sheed & edges will be painted to match with prelam sheet & fixed in position as per manufacturer\"s instruction all as specified, as shown on drawing on page No 160 of SSR Part-II 2010. |
| 47 | S&F in repairs factory made solid panel PVC door wire gauzed shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of stainless steel wire cloth i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly. |
| 48 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified and as directed. |
| 49 | Hacking out old broken glasses any thickness, size, quality or description from wooden frames glazed with putty or fixed with bead all as specified and as directed. |
| 50 | All as per Serial item No. 49.00 here in above but from metal frame including punching out or drilling out old glazing pins/ spring clips and providing and fixing new all as specified and as directed. |
| 51 | S&F sheet glass ordinary quality 3mm thickwith oil puttynot exceeding 0.5 sqm in each pane all as specified and as directed. |
| 52 | S&F 4mm thick tinted colouredglass, with oil putty in square innot exc 0.5 sq.m in each pane complete all as specified and as directed |
| 53 | S&F 5.5mm thick sheet glass, ordinary quality, glazing with oil putty or with wooden beads, area exceeding 0.50 Sqm but not exceeding 1.0 Sqm each pane with and includingsolar control film 50 micron reflective type(greatersun control or equivalent) complete all as specified and directed. |
| 54 | S&F in repairs for tinted glass of selected quality, 5.5mm thick and glazing with aluminium beading in aluminium door shutters all as specified and directed. |
| 55 | S&F in repairs Block board, grade 1 quality, exterior grade, commercial type with one side decorative face 18/19mm thick. |
| 56 | M&L in repairs for 12mm thickprelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. |
| 57 | M&L 18/19 mm thickprelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. |
| 58 | S&F butt hinge, medium weight, cold rolled mild steel 100mm long all as specified and as directed. |
| 59 | S&Fbutt hinges, medium weight, cold rolled mild steel 75mm long all as specified and as directed. |
| 60 | S&F aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed all as specified and as directed. |
| 61 | S&Ffloor door stopper of aluminium alloy body double and tongue anodised with rubber shoe and fixed of size 150 mm all as specified and as directed. |
| 62 | S&F aluminium anodised barred tower bolt of extruded section 200 mm long and fixed all as specified and as directed. |
| 63 | All as per Serial item No 62.00 here in above but 150mm long |
| 64 | S&F extruded aluminium alloy handle fabricated type anodised 150 mm long. |
| 65 | All as per Serial item No 64.00 here in above but 100mm long |
| 66 | S&F hasp and staple, safety type aluminium anodised with hinge pin including bolt to hing plate and fixed with screw 125 mm long all as specified and as directed. |
| 67 | M&L for preparing new surfaces of wood of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed. |
| 68 | All as per Serial item No 67.00 here in above but on steel surfaces over red oxide primer. |
| 69 | S&F 100 mm long stainless steel butt hinges all as as directed. |
| 70 | S&F 300 mm long, mild steel ordinary rat rail springs including roller and roller plate complete and taking down old one all as specified and as directed. |
| 71 | S&F in repairs mild steel decorative and colour coated curtain rail, 20mm bore chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed. |
| 72 | S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified & directed. Make : Cera Cat No. F5001103 or Equivalent make of Kohler/Jaquar/Blue Star & Silver Shine/ Prayag |
| 73 | S&F in repair mild steel mortice lock 4 levers, vertical type, size 100mm complete all as specified anddirected. |
| 74 | servicing and greasing of rolling shutter of any type and thickness including replacement nut, screws, etc including taking down carefully of rolling shutter and cover greasing of all parts for smooth functioning of shutter and refixng the same in existing opening/position complete all as specified and directed by Engr-in-Charge. |
| 75 | S&F steel ventilator with top hung shutter including hinges, steel peg stay complete with glazing bars complete all as specified and directed |
| 76 | Servicing and greasing of aluminium door including replacement nut, screw rubber gaslets, pivot, taper clip etc including taking own carefully of door shutter for replacing unserviceable parts/components by new parts for smooth functioning of door and refixing the same in existing opening/position complete all as specified and directed by Engr-in-Charge. |
| 77 | S&F in repair gate and shutter, hooks and eyes 75mm of aluminium plate type II complete all as specified and directed. |
| 78 | S&F in repair door bottom seal brush with metal frame with nylon brush/rubber with height upto 30-40mm fixed with screws to any type of doors(wooden/aluminium/PVC) including necessary fittings complete all as specified and directed. |
| 79 | S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel brass polished complete all as specified and directed. |
| 80 | S&F in repairs for Steel rolling shutters with thickness of lath 1.0 mm, gear operated type with bevelled gear box and and crank handle, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete including taking down old one |
| 81 | S&F in repairs for safety lever locks mild steel with 4 levers for rolling shutters |
| 82 | S&F in repairs for ball bearing for rolling shutters |
| 83 | Supply & fixing and providing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 84 | S&F 12mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes includingglass is ground or obscured or frosted, on one side required complete all as specified. |
| 85 | Cutting holes in brick walls/ post in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required and Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall is not exc half brick complete all as specified and directed. |
| 86 | Grinding, polishing and rounding off edges of glass, any type exc 4 but not exc thick 8mm thickand securing glass in metal frame complete all as specified and directed. |
| 87 | M&L for welding in repairs to broken hinges of doors and windows to metal frame all as specified and as directed. |
| 88 | M/L for welding in repairs not exc 2.5cm in length not exc 6mm thickall as specified . |
| 89 | S&F in repairs providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 90 | Providing and fixing in repairs factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with multi chamber, frame(60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware : casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild steel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated). Note: The unit rate quoted by contractorincludes all other connected accessories. Net opening will be measured for payment purpose. |
| 91 | Providing and fixing in repairs factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. 4.8mm thick glazing & Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Note: The unit rate quoted by contractor includes all other connected accessories. Net Opening will be measured for payment purpose. Area not exceeding 2.00 sqm each Make of section : HINDALCO / JINDAL/ INDAL as approved by GE. |
| 92 | S&F in repairs Aluminium, coloured powder coated window shutter (sliding type) with two track aluminium anodised frame made of standard section, 90mm x 45mm x 2.0mm thick (outer frame) and inner frame i.e. Bombay sliding of section 38mm x 20mm x1.50mm thick including necessary jointing cleats, glazing clips, aluminium anodized snap beading, screws, aluminium beading, PVC packing, aluminium anodised fittings such as 100mm size handle (decorative type ) 01 No (each shutter) and other necessary fitting and fixture with and including 4.80mm thick tinted glass selected quality with necessary beading/packing,compete all as specified and directed. Make of section : HINDALCO / JINDAL/ INDAL as approved by GE. |
| 93 | S&F in repairs Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement and direction of Engineer in-Charge. |
| 94 | Supply only for 6mm thick, (consisting of 5 Nos of Ply),plywood BWR, type BB. |
| 95 | Supply only for 12mm thick, (consisting of 5 Nos of Ply),plywood BWR, type BB. |
| 96 | S & F Block board 18/ 19 mm, grade 1 quality, exterior grade, commercial type, decorrative type on both faces |
| 97 | S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 98 | Dismantling asbestos cement, galvalume, fiber sheet (Plain, corrugated , semicorrugated etc.) sheet in roof covering all as specified and directed. |
| 99 | S&F Pre painted GalvaIume aluminium zinc coating GI based corrugated steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws etc complete all as specified and directed. |
| 100 | S&F Pre painted GalvaIume aluminium zinc coating GI based Plain steel sheet0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge of roofcovering fixed with self tapping screws etc complete all as specified and directed. |
| 101 | S&F 2mm thick fibre glass reinforced translucent corrugated sheet with two corrugation sheet with two corrugation side laps fixed with L-type or J-type or cranked hook bolts all as specified and as directed, including taking down oldsheet. |
| 102 | S&F in repairs Door closer hydraulically regulated, designation No 3,aluminium (die cast ) body, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed including taking down old one all as specified and directed. |
| 103 | S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty all as specified and directed. including taking doen old floof spring hydraulically. |
| 104 | Material and labour for Granite of 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms andlike in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and mouldidng/rounding the edgecomplete all as specified and directed. |
| 105 | Demolition of cement concrete (reinforced) Roofs,floors(otherthan ground floors), beams, staircases, Landing, chajjas and similar suspended work of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition)complete all as specified and as directed. |
| 106 | M&L for Reinforcement cement concrete 1:2:4 type B-0, (using 12.5mm graded stone aggregate) for chajjacomplete all as specified and as directed |
| 107 | Use & waste formwork for fair finished flat surfaces of concrete to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed |
| 108 | M &L for repairs to ends of chajja by removing the old loose concrete material, cleaning the reinforcement and finishing the surface apply epoxy base resin of manufacturer pidicrete and choksey and make good with concrete 1:1.5:3 as required to existing broken surface and fair and even in cement mortar 1:3 with epoxy coating and applying two coats of weather proof emulsion paint upto 600mm depth and 100 mm thickness including necessary scaffolding as required at site etc |
| 109 | M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamelpaint of approved tint over a coat of zinc chrome primer complete all as specified & directed by Engr-In-Charge. |
