Tender For Petty Repairs And Certain Other Misc B/R Works In Bde Area In Zone-Iii Under Ge (S) Jaipur At Jaipur Mil Stn; 1 M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed. 2 M&L for drilling suitable holes in reinforced cement concrete with power driven drill machine to a minimum depth of 10D (D-dia of bar in mm) inRCC beams, lintels, columns and slabs to introduce new steel barsincluding cleaning the holes by air blowers prior to fixing the new steel bars in position using Lokfix E77, a two-component epoxy anchoring material, supplied in 3:1 ratio having compressive strength (EN196) not less than 122 N/sqmm, Flexural Strength (EN196) not less than 66 N/sqmm, E Modulus (EN ISO 527-2) 6300 N/sqmm or of equivalent make but excluding the cost of reinforcement, complete all as per direction of Engineer-in- Charge for 10mm dia shear connectors. Note : 1. Anchoring chemical shall comply with ETA 21/0354, ETA 21/0518 for anchoring bars for 10mm dia complete all as specified and directed.2. Reinforcement shall be measured and paid separately. 3 M&L for chipping of plaster / unsound weak and cracked concrete / cover of reinforcement of RCC member like slab, beam, column, chhaja etc or as per site requirement by standard power driven percussion type or pneumatic chisel including tapering all edges, making square shoulder of cavities etc and disposal of debris / malwa from site complete all as specified and directed. 4 M&L for cleaning of existing reinforcement with wire brush/rotary wire brush to make surface free from rust scales, loose material, dirt etc. complete and applying two coats of alkline rust converting primer on the existing rebar and allowing it to react with rust for 6 hours and form corrosion resistant, insoluable and adherant protective layer, including cleaning the reinforcement wire brushing to remove the rust spalls, with time interval of 1 hour between the coats complete all as specified and directed. 5 M&L for corrosion inhibiting impregnation coating, designed for use as an imregnation for protection of steel reinforcement within unexposed concrete with in consumption of 0.5 Kg/Sqm. The product should be amino alcohol and inorganic combination based migratroy corrosion inhibitor for both cathodic and anodic protection complete all as specified and directed.Make : Fosroc / Thermax / Sika or equivalent as approved by GE. 6 M&L for zinc rich epoxy anti-corrosive protective coating for rebar corrosion protection system complete all as specified and directed.Make : Fosroc / Thermax / Sika or equivalent as approved by GE. 7 M&L for providing, mixing & applying two component of epoxy resin concrete bonding coat on prepared RCC surfaces as per manufacturer specification including prepartion of surface by chipping and throughly cleaning of surface complete wherever required complete all as specified and directed. Make : Fosroc / Thermax / Sika or equivalent as approved by GE. 8 M&L for re-building the section of damaged RCC elements to its original size on an average 15 mm thickness in two layers each by providing and applying with pre- batched, polymer modified mortar of approved make having compressive strength not less than 50 N/sqmm (28 days) as per ASTM C-109 and flexural strength not less than 05 N/sqmm (7 days) as per ASTM C-293-79 standards including water fog curing to keep surface moist for seven days complete all as specified and directed. Make : Fosroc / Thermax / Sika / Dr. fixed or equivalent make as approved by GE.Note : (i) To achieve the required thickness, the above process should be repeated after 24 hours.(ii) Surface area with 15mm thick layer will be measured as one unit for payment purpose.(iii) Rate shall be including all necessary scaffolding upto height of four storey building. 9 M&L brick work using old size sub class B bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. 10 M&L for brick work (except brick), straightor curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.Note : Serviceable old bricks obtained from dismantling shall be re-used under this item. 11 S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both face are covered with decorative face veneer with lipping / frame to match complete all as specified and directed. 12 Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed. 13 Taking down chowkats or frames exc. 1.5 sqm but n.exc 4.0 Sqm each with shutters (without taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed. 14 S&F second class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed. 15 S&F35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. 16 Taking down shutters of any description exc. 1.00 Sqm but n.exc. 2.00 Sqm each complete all as specified and directed. 17 S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed. 18 S&F for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified anddirected 19 S&F Factory made Solid PVC Moulded door shutter with particle board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. 20 S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed. 21 S&F aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed. 22 S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed. 23 S&F butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed. 24 S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. 25 S&F extruded brass handles, fabricated type polished of 100 mm size complete all as specified and directed. 26 S&F aluminium handles cast type anodised of 125 mm size complete all as specified and directed. 27 S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed. 28 S&F in repair 100 mm Mortice latch with two levers (vertical type), brass body complete all as specified and directed. 29 S&F in repair harrison rail (curtain rail) mild steel chromium plated with fixing brackets ,stops, rollers etc complete as all specified and directed. 30 S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed. 31 S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. 32 S&F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed. 33 S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. 34 S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified and directed. 35 M&L for auto close hinges, stainless steel, bright finish or electrogalvanisedfixed complete all as specified and as directed. 36 S&F powder coated anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed. 37 S&F rolled mild steel section as in joist ,channel,angle or tee sections fixed independently ,with out connecting plates etc (cut to ordinary length i.e within 20 mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed 38 S&F rolled mild steel section in roof trusses (framed), trussed, purlins, crane gantries,rail and fastenings and heavy bracket framing (beam, tee, angle,channel or flat sections) including distance pieces, cleat etc of gradeFe 410-W (Gde E-250) quality B complete all as specified and directed. 39 S&F rolled mild steel section in framed work as in doors or gates of angle or other section withgusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging of grade Fe-410-W(Gde-E-250) quality-B complete all as specified and directed. 40 M&L for powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. 41 S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note:- Glass and other filling material in panels shall be measured and paid seperately. 42 S&F for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. Note-Glass and other filling material in panels shall be measured and paid seperately 43 M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed. 44 S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 45 M&L for 18-20 mm thick High Density high moisture resistant (HDHMR) board for kitchen cupboard / door shutter of make Action tesa / Pearlwood or equivalent make as approved by GE, one side colour / white laminate and other side decorative as in modular kitchen / cabinets / door shutter fixed with minifix hardware wherever required including edge band 22mm wide, 0.80mm thick of matching colour on exposed surfaces of board fixed with polymaster adhesive of REHAU make or equivalent including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc. complete all as specified and directed. 46 M&L for machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing andpolishing on treads of step and landing of stair including screed bed 15 mm thick in CM 1:6 complete all as specified and directed. 47 M&L for machine cut kota stone slab mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) in riser of step ,skirting, dado and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing andpolishing including rendering 10 mm thick in CM 1:4 complete all as specified and directed. 48 M&L for granite (of any type) tiles 20 mm thick machine cut,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including screed bed 15 mm thick in CM 1:6 complete all as specified and directed. 49 M&L for mirror polishing on marble / granite / Kota stone / stone work where ever required to give high gloss finish complete all as specified and directed. 50 M&L for glazed ceramic coloured tiles in vertical surface350x 250x 7 mm / 450X 350X 7 mm / 300x 600x7 mm / 450x 300x7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and directed. 51 M&L for non skid ceramic coloured tiles of design as approved7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed. 52 M&L for non skid joint free ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 53 M&L for full body vitrified Ceramic tiles light shade cut out of 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in vertical surface such as dado / skirting / risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in CM 1:4 complete all as specified and directed. 54 M&L for full body vitrified Ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed. 55 Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing)and removing rubbish off the premises complete all as specified and directed. 56 Dismantling of existing sunken treatment including plaster and M&L for water proofing treatment on existing sunken portion with the following specification :-(a) 40 mm thick PCC 1:2:4type B-0using 12.5 mm graded stone aggregate as in sub base flooring.(b) 15 mm thick (average) plaster on sunken floor in CM (1:4) with and including water proofing compound as per manufacturer instruction complete all as specified & directed.(c) Apply bituminous primer @ 0.5 Kg / Sqm conforming to IS 3384 -1965on prepared surface till the surface is properly impregnated.(d) Apply hot bitumen 85/25 grade @ 1.2 Kgs/Sqm confirming to IS 702-1988.(e) Laying polymeric water proofing membrane weight not less than 3.0 Kgs /Sqm as per manufacturer instructions confirming to relevant IS (Make:- STP Ltd / Pidilite / Tikitar).(f) Apply layer of blown grade bitumen 85/25 @ 1.2 Kgs/Sqm confirming torelevant IS.(g) One spout of 40 mm GI Pipe Shall be provided in Sunken floor and sunken portion shall be filled with lean concrete Type E-2 (1:5:10) using brick Coarse aggregate. 57 Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. 58 M&L for rendering 10 mm thick in CM 1:3 as in ceiling surface and finished even and smooth without using extra cement complete all as specified and directed. 59 M&L for rendering on stone masonry or other than fair faces of brick work of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed. 60 M&L for preparation of newly plastered surfaces of ceilings and apply two coat of white wash including including 1 mm thick wall care putty complete all as specified and directed. 61 M&L for preparation of old decorated surfaces of ceiling by complete removal of existing treatment and apply two coat of white wash including 1 mm thick wall care putty complete all as specified and directed 62 M&L for preparation of old (plastered or unplastered) surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed. 63 M&L for preparation of new surface of wall of any description and applying two coats of oil bound distemper (OBD) over and including 1 mm thick wall putty all as specified and directed. 64 M&L for complete removal of existing treatment and preparation of old surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of alkali-resistant priming paint over and including 1 mm thick wall putty all as specified and directed. 65 M&L for preparation of old plastered surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed. 66 M&L for two coats of cement based paint on new plastered surface of walls over a coat of alkali resistant priming paintincluding preparation of surface complete all as specified and directed. 67 M & L for one coat of cement based paint on old plastered surface of wall including preparation of surfaces upto two/three stroey building including scaffolding arrangement complete all as specified and directed. 68 S&F 3 mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. 69 S&F 4.8 mm thicksheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. 70 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone,concrete orbrick surrounds, glazed with putty of fixed with beads complete all as specified and directed. 71 M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed. 72 M&L for preparationof old painted surfaces of steel of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed. 73 M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 74 M&L for preparationof new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 75 Dismantling water tanks of any description, capacity exc 500 and not exc 1000 litres and removing from site complete all as specified and directed. 76 S&Frotational moulded polyethylenewater storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in positioncomplete all as specified and directed 77 M&L for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed. 78 M&L for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed. 79 M&L for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, fixed to walls of 75 mm bore of pipe etc complete all as specified and directed. 80 M&L for PVC (SWR) pipessingle socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed. 81 S&F PVC (SWR) bends any radius of 75 mm borewithoutaccess door complete all as specified and directed. 82 S&F PVC (SWR) branch piece single (single Y) equal or unequal of 110 mm bore of pipe complete all as specified and directed. 83 S&F PVC (SWR) junction double ,(double T) equal or unequal of 110 mm bore of pipe with access door complete all as specified and directed. 84 M&L PVC (SWR) P trap of 110 mm bore including jointing with solvent cement complete all as specified and directed 85 M&L PVC (SWR) multi floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed. 86 M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed 87 S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed. 88 S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed. 89 Taking up or down steel tubing and connections including cleaning if refixingrequired for 15 mm bore of pipe complete all as specified and directed. 90 Taking up or down steel tubing and connections including cleaning if refixingrequired for 20 mm bore of pipe complete all as specified and directed. 91 Dismantling water tanks of any description, capacity exc 250 and not exc 500 litres and removing from site complete all as specified and directed. 92 S&Frotational moulded polyethylenewater storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in positioncomplete all as specified and directed 93 S&F in repair bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrulefancy type of 15 mm bore dia of pipe complete all as specified and directed. 94 S&F in repair for 15mm bore dia of pipepillar taps cast copper alloy, with capstan head chromium platedfancy type screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. 95 S&F in repair for 15mm bore dia of pipe brass CP swan neck, wash hand basin mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.Make : Jaquar CAT Part No OPP-CHR-15011BPM / Kohler CAT Part No 22534IN-4-CP / Grohe CAT Part No 32851000 or equivalent as approved by GE. 96 S&F in repair for 15mm bore dia of pipe brass CP wall mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed. 97 S&F ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 15 mm bore of pipe complete all as specified and directed. 98 S&F ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 20 mm bore dia of pipe complete all as specified and directed. 99 S&F ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 25 mm bore dia of pipe complete all as specified and directed. 100 S&F in repair waste fittings, brass, chromium plated 32mm dia for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. 101 S&F waste coupling of PTMT for 32 mm bore dia of pipe half or full threaded (minimum weight 45gms) complete all as specified and directed. 102 S&F in repair waste coupling of PTMT for 32 mm bore dia of pipe half or full threaded (minimum weight 45gms) complete all as specified and directed. 103 S&F in repair waste coupling of PTMT for 40 mm bore dia of pipe half or full threaded (minimum weight 60gms) complete all as specified and directed. 104 S&F grating doom 100 mm dia of PTMT (minimum weight 25 grams) complete all as specified and directed. 105 S&F in repair sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed. 106 S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. 107 M&L in repair wash down water closet vitreous china white pedestal pattern with P or S trap including connecting to outgoing drain pipe & to flushing pipe also including plastic water closet seat, black/white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, excluding flushing cistern and flush pipe complete all as specified and directed. 108 S&F Water closet vitreous china squatting pan, orissa pattern 580x440 mm white with integral foot rests excluding flushing cistern and including provision of lime concrete bedding ,P or S trap 100 mm bore , flushing pipe, anti-syphonage pipe and connection etc and making good to floor complete all as specified and directed. 109 M&L in repair for Vitreous China urinals, bowl type flat back size of 465 x 355 x 265 mm white (minimum)with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as sapecified and directed. 110 S&F in repair PVC 10 litres capacityvalveless ,syphonic action type low level flushing cistern ,white including flush pipe, inlet, ball valve, float and handle etc complete all as specified and directed. 111 S&F in repair brass chromium platedshower rose 125 mm size with or without swivel joint complete all as specified and directed. 112 M&L in repair toilet paper holder , of stainless steel with flat recessed type, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. Make:- Jaquar CAT Part No. CPA-CHR-1151 / Grohe Cat Part No. 40367000 / Kohler cat Part No. K-5633IN-CP or equivalent as approved by GE. 113 M&L in repair for Wash basins, Vitreous China, white, flat back, size 630x450mm excluding taps, waste, chain and plug andporcelainstopper but including brackets & cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed. Make : Jaquar / Hindware / Cera or equivalent make as approved by GE. 114 S&F in repair looking mirror 5.5 mm thick of selected quality glass of size 600 x 450 mm bevelled edge , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screw and cup washers including aluminium anodized frame complete all as specified and directed. 115 S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longcomplete all as specified and directed. 116 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 117 S&F in repair angle cock cast copper alloy for 15 mm bore dia of pipe screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. 118 S&F in repair for 32 mm borebrass chromium plated bottle trap for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.Make:- Jaquar Cat part No. ALD-CHR-769L300x190 / Grohe Cat Part No. 28920000 / Kohler cat Part No. K-9033-CP or equivalent as approved by GE. 119 S&F in repair waste coupling of brass CP for 32 mm bore dia of pipe half or full threaded with long shank complete all as specified and directed. 120 S&F in repair liquid Push Button Soap Dispenser of brass fixed with and including chromium plated brass screws complete all as specified and directed.Make : Jaquar CAT Part No SDR-WHT-DJ0010FN or equivalent model of make Kholer / Roca / Grohe as approved by GE. 121 S&F in repair CP Stainless Steel Wall Mounted Square Soap Dish / Soap Stand / Soap Holder, approximate size 160x 160mm fixed to plugs with chromium plated brass screws complete all as specified and directed 122 Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 123 Demolition of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floor, apron etc complete all as specified and directed. 124 Demolition of cement concrete un-reinforced in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. 125 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 126 Dismantling of plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coveringscomplete all as specified and directed. 127 Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 100 mm internal dia of pipe complete all as specified and directed.
