Tender For Repair/Maintenance Of Pump, Motors And Connected Items At Af Stn Phalodi; 1 Dismantling of Electric Motor 40 HP Capacity installed as motor from foundation after disconnecting electrical connections, dismantling motor ,transporting to civil workshop for repairing and rewiding the same with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and greasing of bearings, bushes and other connected parts, reassembling and fixing the same in its original position including replacement of unserviceable nut-bolts, washer, lugs, terminal plate and making proper electrical connection and testing on load complete all as specified and directed.Note : - (i) Bearing if required for replacement shall be measured and paid seprately under respective item.(ii) Transportation of motor deemed to be included in the unit quoted rate of items, nothing extra shall be paid on this account. 2 All as per item No. 1.00 (here-in-before) but motor of capacity 20 HP. 3 All as per item No. 1.00 (here-in-before) but motor of capacity 15 HP. 4 All as per item No. 1.00 (here-in-before) but motor of capacity 10/12.5 HP. 5 All as per item No. 1.00 (here-in-before) but motor of capacity 7.5/5 HP. 6 All as per item No. 1.00 (here-in-before) but motor of capacity 2/3 HP. 7 Dismantling of defective centrifugal pump set assembled with 40 HP elelctric motor, dismantling the pump set for carrying out repair / replacement of unserviceable parts such as CI impeller, Bush, ball bearing etc. and re-assembling after complete repairing, installing, commissioning and testing complete all as specified and directed.Note :(i) CI impeller/ Bush/ ball bearing shall be measured and paid as supply onlyunder respective items of BOQ.(ii) Transportation of motor/pump deemed to be included in the unit quoted rate of items, nothing extra shall be paid on this account. 8 All as per item No. 7.00 (here-in-before) butpump set assembled with 20 HP elelctric motor. 9 All as per item No. 7.00 (here-in-before) butpump set assembled with 15 HP elelctric motor. 10 All as per item No. 7.00 (here-in-before) butpump set assembled with 10/12.5 HP elelctric motor. 11 All as per item No. 7.00 (here-in-before) butpump set assembled with 7.5 HP elelctric motor. 12 All as per item No. 7.00 (here-in-before) butpump set assembled with 5 HP elelctric motor. 13 All as per item No. 7.00 (here-in-before) butpump set assembled with 2/3 HP elelctric motor. 14 Supply only ball bearing suitable for centrifugal Pump set assembled with 40 HP motor complete all as specified and directed. 15 Supply only ball bearing suitable for centrifugal Pump set assembled with 20 HP motor complete all as specified and directed. 16 Supply only ball bearing suitable for centrifugal Pump set assembled with 15 HP motor complete all as specified and directed. 17 Supply only ball bearing suitable for centrifugal Pump set assembled with 10/12.5 HP motor complete all as specified and directed. 18 Supply only ball bearing suitable for centrifugal Pump set assembled with 7.5 HP motor complete all as specified and directed. 19 Supply only ball bearing suitable for centrifugal Pump set assembled with 5 HP motor complete all as specified and directed. 20 Supply only ball bearing suitable for centrifugal Pump set assembled with 2/3 HP motor complete all as specified and directed. 21 Supply and laying/fixing in replacement submersible cable flat type, copper conductor of size 10 Sqmm 3 core complete all as specified &directed. 22 Supply and laying/fixing in replacement submersible cable flat type, copper conductor of size 6 Sqmm 3 core complete all as specified &directed. 23 Supply only coupling assembly as per existing model & make suitable for centrifugal pump set assembled with 40 HPmotor complete all as specified &directed. 24 Supply only cooling fan with locking aluminum cast type screw, as per existing type, suitable for 40 HP to 5 HP motor complete all as specified & directed. 25 Supply only gland rope of size 10 sqmm or as required complete all as specified &directed. 26 Disconnecting of submersible pump set of any capacity alongwith column pipe 80mm dia and cable from the bore well of encasing pipe 200 mm bore (length approx 170 mtr) after dismantling existing GI bend 80 mm bore from NRV andsubmersible cable from starter complete all as specified and directed.Note :- The quoted rates shall be deemed to included in unit quoted rate for requisite T&P, equipments, transportation etc. 27 Material and labour for lowering down of submersible pump set of any capacity alongwith connected items such as column pipes & submersible cable (length approx 170 mtr) re-connecting, commissioning and testing complete all as specified and directed.Note :- The quoted rates shall be deemed to include for requisite T&P, equipments, transportation etc. 28 Dismantling of 40 HP capacity submersible pump, multi stage examining for worn out/defective parts and renewal defective parts, cleaning properly, thereafter reassembling the pump, commissioning and testing complete all as specified and directed. 29 All as per item No. 36.00 (here-in-before) but 30 HP capacity.Note for item Nos 36.00 to 37.00 :(i)Spare parts shall be measured and paid as supply only under relevant itemof BOQ.(ii)The unit quoted rate deemed to included for necessary T&P, equipment, transportation etc required to repair submersible motor of any capacity.(iii)Make of parts shall be as per original manufactrurer of submersible pump. 30 Material and Labour for rewinding of 40 HP submersible pumps motor, electric driven 415 Volt, 50 Hz, 3 phase AC supply with PVC insulated, Super enamelled Copper winding wire of suitable/existing gauge, ISI marked, including all insulated material such as adhesive, insulating paper steeves, tape etc. and connected works for rewinding & including assembling and reassembling the motor complete all as specified and directed. Note :- The quoted rates shall be deemed to included dismantling, removal of old winding wire, cleaning of slots and reassembling complete. 31 All as per item No. 38.00 (here-in-before)but 30 HP capacity. 32 Supply only Upper and lower rubber housing bush, 3 phase, 50 Hz AC submersible motor of 40 HP capacity for replacement under item No. 40 (here-in-before) complete all as specified and directed. 33 All as per item No. 40.00 (here-in-before) but Stainless steel rotor sleeve complete all as specified and directed. 34 All as per item No. 40.00 (here-in-before) Carbon thrust bearing complete set complete all as specified and directed. 35 All as per item No. 40.00 (here-in-before) but Upper and lower CI housing complete all as specified and directed. 36 Supply only Upper and lower rubber housing bush, 3 phase, 50 Hz AC submersible motor of 30 HP capacity for renewal under item No. 41.00 (here-in-before) complete all as specified and directed. 37 All as per item No. 44.00 (here-in-before) but Stainless steel rotor sleeve complete all as specified and directed. 38 All as per item No. 44.00 (here-in-before) but Carbon thrust bearing complete set complete all as specified and directed. 39 All as per item No. 44.00 (here-in-before) but Upper and lower CI housing complete all as specified and directed. 40 Supply only rotor assembly for 40 HP capacity of submersible motor to match with existing make and size for renewal under item No.40.00 (here-in-before) complete all as directed and specified. 41 Supply only rotor assembly for 30 HP capacity of submersible motor to match with existing make and size for replacement under item No. 41.00 (here-in-before) complete all as directed and specified 42 Supply and fixing in renewal of 3 pole power contactor 80 Amps with AC coil, AC 3 duty rating at 415 Volts, 50Hz and Coil Voltage as specified at site of motor starter complete all as specified and directed. 43 Supply and fixing in renewal of 3 pole power contactor 60 Amps with AC coil, AC 3 duty rating at 415 Volts, 50Hz and Coil Voltage as specified at site of motor starter complete all as specified and directed. 44 Supply and fixing in renewal of 3 pole power contactor 40 Amps with AC coil, AC 3 duty rating at 415 Volts, 50Hz and Coil Voltage as specified at site of motor starter complete all as specified and directed. 45 Supply and fixing in renewal of 3 pole power contactor 25 Amps with AC coil, AC 3 duty rating at 415 Volts, 50Hz and Coil Voltage as specified at site of motor starter complete all as specified and directed. 46 Supply and fixing in replacement Digital type V,A,F,PF,KW,KVA meter 96mm x 96mm, of range 0-500 volts, class -1, including internal wiring with 1.0 Sqmm single core PVC wire etc complete all as specified & directed. 47 Supply and fixing in replacementvolt meter analog type , three phase,TRMS using micro controler , 4 digit high resolution display , class -1, including internal wiring with 1.0 sqmm single core PVC wire etc complete all as specified & directed. 48 Supply and fixing in replacement oveload relay, range 28-40 Amp, suitable for 30 HP motor, 3 phase, 415 volt, 50 Hz as per sample complete all as specified and as directed. 49 Supply and fixing in replacement oveload relay, range 45-65 Amp, suitable for 40 HP motor, 3 phase, 415 volt, 50 Hz as per sample complete all as specified and as directed. 50 Supply and fixing in renewal of automatic star delta Submersible motor starter in steel sheet enclosure AC 3 phase, 415 Volts, 50 Hz type MUG with single phase preventer, dry run preventer, overload protection, reverese phase protection suitable for 40 HP submersible pump set (Contactor rating minimum 65 Amps, Overload Relay Range minimum 34 to 50 Amps) complete all as specified and directed. 51 Supply and fixing in renewal of automatic star delta Submersible motor starter in steel sheet enclosure AC 3 phase, 415 Volts, 50 Hz type MUG with single phase preventer, dry run preventer, overload protection, reverese phase protection suitable for 30 HP submersible pump set (Contactor rating minimum 65 Amps, Overload Relay Range minimum 34 to 50 Amps) complete all as specified and directed. 52 S & F in renewal of DOL submersible pump starter in steel sheet enclosure AC 3 phase, 415 Volts, 50 Hz type MUG with single phase preventer, dry run preventer, overload protection, reverese phase protection suitable for 5 HP submersible/monoblockpump set complete all as specified and directed. 53 S & F in renewal of DOL Submersible motor starter in steel sheet enclosure AC single phase, 230 Volts, 50 Hz type MUG with single phase preventer, dry run preventer, overload protection, reverese phase protection suitable for 5 HP submersible/monoblock pump set complete all as specified and directed. 54 Supply and fixing in replacement single phase preventer type SDz5, SPPR + Timer, 415 V including necessary copper connection, lugs etc complete all as specified & as directed. 55 Supply and fixing in replacement on / off switch (push button) complete all as specified & as directed. 56 Supply and fixing in replacement indicating lamp with holder and cover as per existing complete all as specified & as directed. 57 Supply and fixing in replacement MCCB 4 Pole 63 Amps, thermal magnetic releasehaving, breaking capacity 25 KA, 415 Volt in the existing feeder pillar box including any addition / alteration to the panel to accommodate the new MCCB & making connections with 25x3 mm copper strip as required from main bus bars,making necessary welding work, metal work for fixing base plate etc and connections complete all as specified and as directed. 58 Supply and fixing in replacement MCCB 4 Pole 125 Amps, thermal magnetic releasehaving, breaking capacity 25 KA, 415 Volt in the existing feeder pillar box including any addition / alteration to the panel to accommodate the new MCCB & making connections with 25x3 mm copper strip as required from main bus bars,making necessary welding work, metal work for fixing base plate etc and connections complete all as specified and as directed. 59 Material and labour for preparation of old painted steel surfaces of panel body of any size including scrapping old paint, denting and applying two coats of spray paint using synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 60 Material and labour for complete removal of existing paint of Electeic motor with pump including base frame and applying two coats of spray paint using synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 61 Material and labour for complete removal of existing paint of pipeline of dia 80mm to 150mm, including base frame and applying two coats of spray paint using synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 62 Material and labour for complete removal of existing paint of pipeline of dia 200mm and 350mm, including base frame and applying two coats of spray paint using synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 63 Supply and fixing in repair fully automatic water level indicator with indicate 12 different level of the tank suitable for use at water supply installations on overhead reservoir and UG sump consist of all connected items & wire etc complete all as specified and directed. 64 Supply and fixing electronic water pressure switch pressure range 0 to 14 bar complete all as specified and directed. 65 Supply and fixing in repair fan belt B-32 ofISI marked best qualityof air compressor.The fan belt B-32 shall be complete all as specified and directed.Note :Fan belt shall be approved by GE before incorporation in the work. 66 Supply and lay in replacement of new electrical insulation rubber matting as per ISI and size 1mtrx2mtrx19mm suitable for installations/panel boards tested suitable all as specified and directed. 67 Supply and fixing in replacement pressure gauge air water meter of pressure range 0-10 kg/Sqcmcomplete all as specified and directed. 68 M & L for Earthing complete with GI plate60×60cm×3 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion including dismantling old earthing all as specified and directed. Note: The unit rate includes for protection pipe and GI wire 4mm dia from top of earth plate up to 7.5 meter above ground level. 69 Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed.Note:-(i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.(ii) The Rate of Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection deemed to be included in unit quoted rate. 70 Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core complete all as specified and directed.Note:-(i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.(ii) The Rate of Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection deemed to be included in unit quoted rate. 71 Supply, laying, testing and commissioning cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, elecric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 core complete all as specified and directed.Note:-(i) Cable may be laid in trenches, under road, across the Nallah, along poles/walls and ducts etc.(ii) The Rate of Excavation, earthwork, sand cushioning, cable cover, pipe for cable protection deemed to be included in unit quoted rate. 72 Supply and fixingin renewal of RO membrane suitable for discharge 2.5 Cum/Hr capacity RO plant (model 4040), Type - Cross linked fully aromatic polymide composite, MOC - Cellulose Polyamide, Salt Rejection % - 99.0 to 99.7, Make/Model : Hydronautics/4040 including connected accessories complete all as specified and directed. 73 Supply and fixing in renewal of RO membrane suitable for discharge 3.0 Cum/Hr capacity RO Plant (Model 8040), Type - Cross linked fully aromatic polymide composite, MOC - Cellulose Polyamide, Salt Rejection % - 99.0 to 99.7, Make/Model : Hydranautics/8040 including connected accessories complete all as specified and directed. 74 Material and labourfor repair and servicing, testing of Chemical dosing (Metering) Pump electromagnet type with suction & discharge tubing, Spring loaded anti siphon valve, foot valve and replacement of broken storage tank 500 ltr capacity etc complete all as specified and directed. 75 Supply and fixing rotational moulded polyethylene water storage tank white colour double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-Iof 5000 Ltr capacity including dismantling old water tank complete all as specified and directed. 76 Supply and fixing in renewal of rubber gasket at both ends of flanged column suitable for GI column pipe of 80mm dia complete all as specified and directed. 77 Material and labour in renewal of nut and bolt with washer, heavy grade suitable for GI flanged column pipes of 80mm dia complete all as specified and directed. 78 Material and labour in renewal of GI column pipe 6 meters length, medium grade, 80mm bore dia with welded flages at both ends and including dismantling holes/spot in flange complete all as specified and directed. 79 Supply and fixing in replacement Hose box made of 18 gauge MS Sheet 800mm X 600mm X 250mm with double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted fire red out side and brilliant white inside Yard complete all as specified and directed. 80 Supply and fixing in replacement 19mm dia hose reel drum 30mtr complete all as specified and directed. 81 Supply and fixing in replacement double headed hydrant valve complete all as specified and directed. 82 Supply and fixing in replacement CI body butter fly valve half round type ISI marked including nuts, bolts, joint, rubber insertion sheet of 100mm diacomplete all as specified and directed. 83 Supply and fixing in replacement CI body butter fly valve half round type ISI marked including nuts, bolts, joint, rubber insertion sheet of 150mm diacomplete all as specified and directed. 84 Supply and fixing in replacement CI body butter fly valve half round type ISI marked including nuts, bolts, joint, rubber insertion sheet of 80mm diacomplete all as specified and directed. 85 Supply, install, connecting and testing of 150 mm bore sluice valve, class PN- 1.6 flanged ends, with CI body, wheel and brass spindle and nuts etc, non rising type IS- 14846:2000 marked including jointing materials i.e. rubber gaskets, nuts, bolts etc. includingtaking down old unserviceable sluice valvecomplete all as specified and directed. 86 Supply, install, connecting and testing of 100 mm bore sluice valve, class PN- 1.6 flanged ends, with CI body, wheel and brass spindle and nuts etc, non rising type IS- 14846:2000 marked including jointing materials i.e. rubber gaskets, nuts, bolts etc. includingtaking down old unserviceable sluice valvecomplete all as specified and directed. 87 Supply, install, connecting and testing of 80 mm bore sluice valve, class PN- 1.6 flanged ends, with CI body, wheel and brass spindle and nuts etc, non rising type IS- 14846:2000 marked including jointing materials i.e. rubber gaskets, nuts, bolts etc. includingtaking down old unserviceable sluice valvecomplete all as specified and directed. 88 M & L for taking down old unserviceable Non return valve and Supply, install, connecting and testing of 100 mm bore Non returning valve, class PN- 1.6 flanged ends double ball type , with CI body, non rising type IS- marked including jointing materials i.e. rubber gaskets, nuts, bolts etc. complete all as specified and directed. 89 M & L for taking down old unserviceable Non return valve and Supply, install, connecting and testing of 80 mm bore Non returning valve, class PN- 1.6 flanged ends double ball type , with CI body, non rising type IS- marked including jointing materials i.e. rubber gaskets, nuts, bolts etc. complete all as specified and directed. 90 M& L forto rectify the leakage of CI/DI pipe of size 150 to 250 mm boreinclduing all required material to rectifiy the leakage in existing valve pits including making good the disturbed surface of pitscomplete all as specified and directed. 91 M& L forto rectify the leakage of CI/DI pipe of size 80 to 100 mm boreinclduing all required material to rectifiy the leakage in existing valve pits including making good the disturbed surface of valve pitscomplete all as specified and directed 92 Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth or n exc 10 Sqm on plan and n exc 1.5 m in depth & getting out, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes or for layingunderground cable, pipe lines etc. in soft/ loose soil, complete all as specified & directed. 93 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in soft / loose or hard dence soil complete all as specified and directed. 94 Removing excavated surplus material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. 95 M&L for dry tibba sand in trenchesfor cushioning to under ground cable spreading, levelling, hand punning complete all as specified and directed.Note- Punned down thickness will be measured for payment purpose. 96 Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. 97 M&L for brick protectionwith sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as directed. 98 Supply and laying in replacement in trenches 25 mm bore steel water tubing, galvanized, medium grade, with all fittings such as bends, tees, union etc., and including testing complete all as specified and directed. 99 Supply and laying in replacement in trenches 40 mm bore steel water tubing, galvanized, medium grade, with all fittings such as bends, tees, union etc., and including testing complete all as specified and directed. 100 Supply and laying in replacement in trenches 50 mm bore steel water tubing, galvanized, medium grade, with all fittings such as bends, tees, union etc., and including testing complete all as specified and directed. 101 Supply and laying in replacement in trenches 80 mm bore steel water tubing, galvanized, medium grade, with all fittings such as bends, tees, union etc., and including testing complete all as specified and directed. 102 S&F in repair 35/36 watts LED streetlight fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light sourceand connecting with suitable sizeweather proof cable from fittings to the jucntion box and fixing to complete all as specified and directed. 103 S & F street light GI bracket of 0.6 mtr long made out of 25 mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 24 x 3 mm including nuts bolts & washers complete necessary fixing arrangements on pole as directed. 104 Supply only impeller of monoblock pump ofcapacity 20 HP pump complete all as specified and directed. 105 Supply only impeller of monoblock pump as per existing model ofcapacity 05 to 15 HP pump complete all as specified and directed. 106 M & L taking out openwell submersible pump of capacity upto 5 HP after disconnecting electrical connections, dismantling motor and rewiding the same with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and greasing of bearings, bushes and other connected parts, reassembling and fixing the same in its original position including replacement of unserviceable nut-bolts, washer, lugs, terminal plate and making proper electrical connection complete all as specified and directed. 107 M & L serving and cleaning of dewatering diesel engine pump of capacity 5 HP including change engine oil,replace fuel filter,oil filter,air filter and leakage fuel pipe complete all as specified and directed.Note:- Engine oil measured and paid separately 108 Supply only engine oilgrade SAE 20w 40 complete all as specified and directed. 109 S&F for mild steel work as Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W all as per directed.
