Tender For Special Repair Of Toilet Bldg No 233/01, 03, Bde-217, 218 And 219 And Addn/Altn Of Tiling, Roof Ceiling And Roof Treatment Of Bldg No Ra-15 (Or Living Area) Of 75 Med Regt Under Ge (North) Meerut Cantt; 1 Demolition ofbrick work or stone/boulder masonary built in cement mortar incl all quoins arches pillars etc complete all as specified & directed. 2 M&Lold size brick work with sub classfly ash bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed. 3 M&L old sizebrickwork with subclass `B bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 except bricks Complete all as specified and directed. Note Old serviceable bricks retrived from demolition shall be re-used under this item. 4 Demolition of cement concrete of ground floor n exc 15 cm in depthin any position nototherwise specifically provided for complete all as specified & directed. 5 Dismantling, floor, hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises Complete all as specified and directed. . 6 M&L for PCC 1:2:4 type B-1 (using 20mm graded stone agg)25 mm thick for Sub base flooring complete all as specified & directed. 7 M&L Non skid ceramic coloured tiles 7 -8 mm thick (Square/rectangular) area of each tile exceeding 0.11Sqm but not exceeding 0.18 Sqm in floors set and jointed in neat cement slurry and pointed with whiteor colour cemnt to match including 15 mm thscreed ded in cm 1:6 Complete all as specified and directed. 8 M & L Coloured Glazed colour ceramic tiles on vertical surfaces 450x300x7mm thickset and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4)joint free with grout of matching shadecomplete all as specified & directed. 9 Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each incl removing from site complete all as specified & directed. 10 Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.50 Sqm & n exc 4 Sqn eachincl removing from site complete all as specified & directed. 11 S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed. 12 S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) 13 S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified & directed. 14 S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified. 15 S&F powder coated anodised aluminium windows slidingtype (3 shutter type) with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) inclstainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, grill with one or more rebates including S&F 5.50 mm thick black glass complete all as specified and directed. 16 S&F, 4mm thick, black/sheet glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed. 17 M&L, in repair, 18/19mm thick Soild WPC board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed with screws to WPC frame work in cup boards, rebated or flat edged fancyhandle , Magnite lock complete all as specified and directed. 18 M&L Framed work such as grills, angle grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290 Gde E-165 complete all as specified & directed. 19 M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamelover one coat of red oxide primer complete all as specified & directed. 20 M&Lstainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or stainless steel wire staplescomplete all as specified and directed. 21 S & F 30 mm flaps Continuoushinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. 22 Supply & fix 150mm size aluminium alloy handles cast type anodized complete all as specified & directed. 23 S&F aluminium anodised tower bolts 150mm long, of extruded section complete all as specified and directed. 24 S&F aluminium slidingbolt 300 long bolt type with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. 25 S&F mild steel heavy weight butt hinges 100mm in sizecomplete all as specified and directed. 26 Taking down of cementplaster of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. 27 M & L 15 mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces finished even and fair complete all as specified & directed. 28 M&L Rendering 5 mm thickon fair faces ofbrick workor concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified & directed. 29 M & Lfor applying 15 mm thick renderingin CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed :Note:- Water proofing compound shall be measured and paid sepratly 30 M& L preparing plastered un plasterednew surfaces on ceiling and applying three coats of white wash on ceiling surface complete all as specified and directed. 31 M&L for preparation of newly plastered surfaces of wall by applying wall care putty averaging thickness 2mm and rubbing with sand paper for making smooth surface and applying two coat of oil emulsion distemper over one coat of primerthrough roller, complete all as specified and directed . 32 M&L for applying 2 mm thick wall care putty making smooth surface complete all as specified and directed. 33 Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces using roller for painting . 34 S&F for 30 mm thick second class hardwood factory madeGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b); supplied and fitted to chowkats complete all as specified and directed. 35 Demolition of reinforced concreteof any description and any poisition not otherwise specifically provide (reinforcement cut to faciliatate demolition) complete all as specified and directed 36 M&L Form work to sides and soffits of beams lintels etc finishedrough complete all as specified and directed 37 M & L RCC 1:2:4 Type B0 (using 12.5mm graded stone aggregate) as in beams, lintels, bressummers over 1.5 m span etc complete all as specified and directed. 38 M & L precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggegrate) as in Chullah hood chajja and manhole cover, kitchen shelves etc set in cement mortar 1:4.including all neccesary formwork & finishing exposed concrete surface complete all as specified and directed 39 Cutting chases ,pinning in brick work girth exc 10cm but n exc 20 cm and making good to facing where required and poiningin cement mortar 1:3 to ends of edges of landing, sun shades, chajjas, shelves etc complete all as specified and directed 40 S&F mild steel TMT bars No 500D 10mm dia and over, cut to length bent to shape requiredincluding cranking, bending spirally for hooping for columns, hooking ends and binding with and including MSwire (annealed) not less than 0.9mm dia or securing clips complete all as specified and directed. 41 ditto as per item no 40but 6 to 8 mm dia complete all as specified and directed. 42 Taking up or down steel tubing and connection 15 mm bore pipe and removing from site complete all as specified and directed 43 All as per Sl Item No.42here-in-before but 20 mm bore pipe complete all as specified and directed 44 Supplying and laying of CPVC 25mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ceiling or laying in floors complete all as specified and directed 45 Supplying and laying of CPVC 20mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ceiling or laying in floors complete all as specified and directed 46 Dismantling OH water tank of capacity exc 250 ltr but not exceeding 500 ltr and removing from site complete all as specified and directed 47 S&F triple layerwhite color 500 Ltrs Rotational moulded polyethylene (PVC) water storage tanks cylindrical vertical with closed top including nipple nuts and washers for fixing inlet, outlet/washout pipes and air vent pipes complete all as specified and directed 48 S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed. 49 S&F in repaircromium plated 15 mm bore size Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed 50 S&F in repair 140mmover all length with flap door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 51 S&F in repair 15 mm dia stop cock/angle cockcast copper alloy chromium plated screwed downhigh pressure with fancy typescrewed both ends for iron or for union complete all as specified and directed. 52 S&F in repair of vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest including replacement of ‘P’ or ‘S’ trap lime concrete bedding and making good floor complete all as specified and directed. 53 S&F in repair Vitreous China wash basin including pedestal, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling complete all as specified. 54 S&F in repair 10 litre capacityPVC valveless, Syphonic action type, fluhing cistern low level,white with inlet ball valve, float and handle including brackets and PVC flush pipe etc complete all as specified and directed. 55 S&F in repair ,PVC(SWR) floor trap, 75mm bore, plain with grating including jointing with solvent cement complete all as specified and directed. 56 S&F in repair ,PVC(SWR) gully trap, 125/110mm bore, plain with grating including jointing with solvent cement complete all as specified and directed. 57 Supply & fix PVC connections of 450mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed. 58 S &FGrating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed. 59 Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required for 110mm and 75mm bore of pipe complete all as specified and directed. 60 Supply and fix75mm bore PVC (SWR)Pipes single socketed in any length with rubber ring joints, fixed to walls and floor etc.as in wastecomplete all as specified & directed. 61 Supply and fix110mm borePVC (SWR)Pipes single socketed in any length with rubber ring joints, fixed to walls and floor etc.as in waste and rain water pipes complete all as specified & directed. 62 Supply and fix PVC (SWR) bends 75mm bore, any radius complete all as specified & directed. 63 Supply and fix PVC (SWR) bends 110 mm bore, any radius complete all as specified & directed. 64 S&F110mm dia PVC (SWR) vent cowl complete all as specified and directed 65 S&F 110 PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed 66 S&F 110mm PVC (SWR) Strap complete all as specified and directed 67 S&F in repair 15mm bore pillar Tap cast coppeer alloy with captan head chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shank and fly nut fancy type complete all as specified and directed. 68 S&F in repair Gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe 15 mm dia complete all as specified and directed. 69 S&F in repairGun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe 20 mm dia complete all as specified and directed 70 S&F in repair factory made 600 x 450 mm beveled edge mirror 5.5mm thick of selected quality glass fixed on 6mm thick commercial ply wood or AC Building board and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 71 S&fIin repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed 72 S&F (in repair) brass chromium plated towel rail 20mm dia D type 600 mm long as a approved quality.complete all as specified and directed. 73 M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas , wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and incl material and labore in CM 1:4 mixed with WPC /PCC 1:3:6 type B0 /Bk work in CM 1:4 as required at site and as directed by Engr-in-Charge 74 Taking down old existing water proofing treatment from the top of RCC/ arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified & directed. 75 Material & Labour for 50mm thick average thickness ofPCC 1:2:4 type B-O(using 12.5 mm graded stone aggregates)all asspecified and directed. 76 Material and Labour for 10mm thick cement paster in CM 1:4 mixed with WPC @ 2 % by weight of cement finised even and smooth without using extra cement on roof surface when concreate is green and wall complete all as specified and directed. Note :- WPC will be measured and paid seperately as supply only rate. 77 Supply only liquid water proofing compound complete all as specified and directed. 78 Material & labour for cleaning of concrete or plasteredsurfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followedevenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thickAPP modified polymeric waterproofing membrane reinforced with non-woven polyester fabric (weightnot less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction andapplying over it a tack coat using 85/25 grade industrial hot blown bitumen bitumen @ 1.20 kg per Sqm and finally finished the top of polymericwater proofing membrane with a coat of bituminous aluminum paint @ 0.20 kg per Sqm as per manufacturer’s instructions complete all as specified & directed. Note :- The above mentioned work shall including existing water tank on roof disconnected and after cleanig re-fixing in same positionconnecting. 79 Surface Preparation:The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane.a) Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges.Note: Grouting will be done when and where ever required.b) Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowablenon shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concreteNote: Will be done when and where ever requiredc ) Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area withsingle component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt.(Note: Contractor is required to deposit 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.” 80 M & L 15 mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces finished even and fair complete all as specified & directed. 81 M & Lfor applying 15 mm thick rendering using ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid sepratly 82 preparation of old surface after complete removal of existing treatment by mechanical means complete all as specified and directed. 83 M&L for applying 3mm thick wall care putty making smooth surface complete all as specified and directed. 84 M&L for 1 coat of primer complete all as specified and directed. 85 M&L for Two coat of OBD complete all as specified and directed 86 M&L for one coat of OBD complete all as specified and directed 87 M&L for two coat of acrylic smooth two or more coat applied @ 1.67 ltr/ 10 sqm over and including primer coat of exterior primer applied @ 2.20 kg / 10 Sqm using roller for painting complete all as specified and directed. 88 M & L Preparation of new plastered surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsiondistemper over one coat of primer using roller for painting complete all as specified & directed. 89 M & L Preparation of new plastered surface of ceiling andapplying two coat of WHITE WASH over one coat of primer using roller for painting complete all as specified & directed. 90 M & L Preparation ofold plastered surface of ceiling andapplying two coat of WHITE WASH over one coat of primer using roller for painting complete all as specified & directed. 91 M & L for Preparing old Plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed 92 M & L Preparation of old painted wood and wood base surfaces of any description, not otherwise described over 10 cm width or girth and painting with a coat of sythetic enamel paint complete all as specified and directed 93 M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 94 M & L for in repair Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed 95 S&F MS angle iron as in door framed work conforming to Fe 290(Gde E-165) including hold fast tie rod, hinges and one shop of red oxide primer etc. complete all as specified and directed. 96 M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier complete all as specified and directed. 97 Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each &removing from site complete all as specified and directed. 98 Taking down chowkhat or frames of door/ window / ventilators with shutter(Without taking off shutter from the frame) n.exc 1.50 m each & removing from site complete all as specified and directed 99 Taking down shutters of any description exc 1.00 m and n.exc 2.00 Sqm & removing from site complete all as specified and directed. 100 M & L for Anodised aluminium Powder Coating (minimum thickness of powder coating 50 micron) frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 101 M & L for Anodised aluminium Powder Coating of Approvedcolour (Thickness or powder coating not less than 50 micron) door Shutter, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium Complete fittings as required complete all as specified and directed. 102 S&F for 4mm thick, black tinted glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed. 103 M&L in repair ,HOLLOW PVC Wall lining consisting of 5 mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on PVC Frame with 5mm pvc fillets as per specified and drawing shown as per page of SSR part II . complete all as specified and directed. 104 S&F in repairplastic seat cover black/white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. 105 S&F in repair vitrous china wash hand basin white flat back, size 580x450mm including waster pipe , chromium plated waste coupling 32mm dia , bracket etc complete all as specified and directed. 106 S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as specified and directed. 107 S&Fin repair stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed. 108 S & F for 35 mm thick Flush shutters, solid core construction, with block board core andplywood face panels,commercial type on both sides face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed. 109 S&F Glazed and skelton shutters 30 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for sucuring witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a) complete all as specified and directed. 110 S&F 100 mmbutt hinges, meium weight Brass complete all as specified and directed. 111 S&F Brass barrel tower bolt 200 mm, extruded section complete all as specified and directed. 112 S& F 300mm long Brass, sliding door bolt withsand or die-cast brass hasp,staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. 113 S & F for 125mm Extruded brass handles,fabricated type polished complete all as specified and directed. 114 S&F, Mortice lock, brass, four lever, verticle type, size 75mm complete all as specified and directed. 115 S&F, in repair, aluminium (Die cast) body, Door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and directed. 116 Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store andd rubbish off the premises complete all as specified and directed. 117 M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick square/ rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in loors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match laidover and including 15mm thick screed bed in CM 1:6 complete as specified and directed. 118 M&L for light shade, vitrified tiles, 8 to 10 mmthick(minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bedding in CM (1:6) complete all as specified and directed. 119 M&L forvitrified tiles, 10mmthick(minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in skirting/dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 10mm thick rendering in CM (1:4) complete all as specified and directed. 120 M&L for glazed ceramic coloured tiles of size 450mm x 350mm x 7mm/600mmx300mmx7 mm on vertical surface such as skirting, dados, risers to steps etc set &jointed in neat cementslurry and pointed inwhite or coloured cementto match the colour oftiles,over and includingrendering10mm thick in cement mortar (1:4) , complete all as specified and directed. 121 M&L for 18 -20mm thick BLACK/RED(LAKHA) granite factory made bull nosed, polished (table rubbed and polished) as in jambs, wall,window cills, cooking platform and the like etc in cement mortar 1:4 including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 including rounding of edges, making hole for gas pipe complete all as specified and directed. 122 M&L for rounding to edges of stone slabs two edge full round, such as in steps,cooking platform and other similar situation complete all as specified and directed. 123 Dismantling water tank of capacity exc 500 ltrs but not exc. 1000 Ltrs complete all as specified and directed. 124 S&F White rotational moulded polyethene water storage tank ( cylinderical verticle with closed top) hoisted and fixed in position all as specified in SSR Part-I. (Cap 1000 ltrs capacity) including inlet / outlet pipe complete all as specified and directed. 125 S&F in repair gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore. 126 M & L for repairs GI tubing concealed or open incl replacing of unserviceable GI fittings, medium grade ISI mark like elbow, socket, nipple, union socket, tee etc with the existing size complete including making necessary threading work to be carried out upto any height or on walls for 15mm bore of pipe complete all as specified and directed by Engineer in Charge. 127 M & L cutting chases for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3to ends or edges etc, cutting not exceeding 10 cm width or girth, complete all as specified and directed. 128 S&F in repairangle valve 15mm bore brass chromium plated with captan head screwed for iron pipe complete all as specified and directed. 129 S&F in repair stop valveschromium plated , 15 dia bore complete all as specified and directed. 130 S&F 15mm dia chromium plated fancy type wall mixer with over head shower for mixing hot & cold water screwed, fixing and connection to pipes complete all as specified and as directed. Make:- Cera Cat Part No F-1017401, Pearl Cat Part No ARI-015, Hindware Cat Part No- F-74 0022 131 S&F 15mm dia chromium plated fancy type sink mixer with swinging spout (wall mounted model)fixing and connection to pipes complete all as specified and as directed. Make:- Cera Cat Part No F 2004501, Pearl Cat Part No ARI-011, Hindware Cat Part No- F 330023 132 S&F in repairPVC connection 15 mm size with PTMT nuts 450 mm long. 133 Dismantling wall and ceiling boads (fibre, pulp, insulation etc.) or insulation boards/ slab/ blankets, any thickness including aluminium snap grid complete all as specified and directed. 134 Material and Labour 4MM THICK Nonasbestos fibre cement building boardsfixed or laid/ inserted to timber/GI/Aluminium framework with screws all as specified and directed 135 S&F Anodised aluminium snap grid frame workframe work of size 605 x 605 mm for false ceiling complete all as specified and directed. 136 Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) complete all as specified and directed. 137 M&L cement concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in 75mm thick sub base complete all as specified and directed. 138 M&L for chequered cement concrete colourtiles glossy finish size 300mm cmx300mmx25 mm thick, with colour pigment, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in cm (1:6) complete all as specified. 139 Taking down carefully any type of battens or conduit point wiringwith conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified and directed. 140 Material and labour for point wiringwith 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth duly complete all as specified and directed for the followings :- 141 One tube light/Bulb/ street light point controlled by one, one way switch 05 / 06 Amps complete all as specified and directed. 142 One fan / Exhaust fan point controlled by one, one way switch 05 / 06 Amps complete all as specified and directed. 143 One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch complete all as specified and directed. 144 One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch complete all as specified and directed. 145 All as per serial item No 140.03 above but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board complete all as specified and directed. 146 Supply and fixswitch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed. 147 Supply and fix insocket outlet 5 pin, 05 / 06 Amps flush type 240 volts complete all as specified & directed. 148 Supply & fixing of socket outlet 3 pin, 05 / 06 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed. 149 Supply and fix inswitch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed. 150 Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed. 151 Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate complete all as specified and directed. 152 Supply and fixing LED lamp 2 pin 9/10 watt complete all as specified and directed. 153 Supply and fixing LED light fitting 1x22/25 watt,220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 154 Supply and fixing LED light fitting mirror type with high output diffuser 2 feet,10 watt 220V, AC decorative type with driver holder and LED lamp including connecting up withthree core flexible copeer conductor cable of suitable size complete all as specified and directed. 155 Supply and fixing 1x36/40W LED Building security lightenergy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security light brackets of 32 mm dia GI pipe medium grade upto 1.2 mtr long bend to shape at 100-120 degree including flat iron clamps and Suitable nuts and bolts grouted in wall including all material required for fitting complete all as specified and directed. 156 Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and directed. 157 Supply and fixing MCB, SP, AC, 240 volts C curve capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed. 158 Supply & fixingDouble pole Isolator 240V, 32A, and making connections complete all as specified & directed. 159 supply and fixing Exhaust fan PVC with louver and fixing accessories 230 Volt and250 mm sweep complete all as specified and directed. 160 M&L for making opening in the wall for fixing exhaust fan up to 250mm / 300mm,including plastering work & making good the surfaces complete all as specifed and directed. 161 S&L XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 10 sqmm 2.0core complete all as specified and as directed.