Tender For Provision Of Water Supply Scheme Alongwith Allied Infra At Rajouri Under Ge 862 Ews; 1 Schedule A Part-I (Building Work) Note :This schedule is not pre-priced by MES and the pre-priced rate indicated as Rs 0.00 under Col. 5 siginifies this fact only. 2 Construction of Pump House building complete all as specified and shown on drawing. 3 Construction of RCC UG Sumpof capacity 40,000.00 Gallon complete all as specified and shown on drawing. 4 Schedule A Part-II (Internal electrification works) 5 Total amount of Sch A Part-II (Internal electrification works) brought forward from srl page No-22 6 Schedule A Part-III (Internal water supply works) 7 Total amount of Sch A Part-III (Internal water supply works) brought forward from srl page No-26 8 Schedule A Part-IV(DG Set Works) 9 Total amount of Sch A Part-IV (DG Set Works) brought forward from srl page No-25 10 Schedule A Part-V(Sewage Disposal Works) 11 Total amount of Sch A Part-V (Sewage Disposal Works) brought forward from srl page No-27 12 Schedule A Part-VI (External electrification Works) 13 Total amount of Sch A Part-VI (External electrification Works) brought forward from srl page No-31 14 Schedule A Part-VII (External water supply Works) 15 Total amount of Sch A Part-VII (External water supply Works) brought forward from srl page No-33 16 Schedule APart-VIII (Misc Items of Works) Note :This schedule is not pre-priced by MES and the pre-priced rate indicated as Rs 0.00 under Col. 5 siginifies this fact only. 17 Construction of conventional type on site LLDPE septic tank designed to carry sewage and sludge water for 05 users with & including earthwork in any type of soil, PCC 1:4:8 below foundation, vent shaft & making connection, complete all as specified and directed. 18 Costruction of soakage well 2.40 mtr dia and 3.00 mtr depp below inlet (depth) from inlet pipe to ground level 45cm including excavation and earth work in any type of soil, PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate in foundation, wall in honey combed brick work in CM 1:4 cover slab of M-25 filling with brick bats, earth cushion on brick lining on top and inlet pipe 150mm dia and complete all as specified and shown on drawing 19 Supply Insttalation and testing of30 HP centrifugal, Pump set heavy duty with fully automatic star delta starterelectric driven,415 volt 3 phase 50 Hz. discharge capacity of pump set should be440 LPM at 135 Mtr head.completerequired with all necessary fitting and copper cablesingle core 70 sqmm for connection from LT panel to Starteras per suitable length in three phase supply including panel board of suitable size for fixing the starter and PCC foundation with chasis complete with nut bolt and channal all as directed at side(01+01 nos stand by) complete all as specified and as directed by Engineer-in-Charge. 20 Supply and fixing of CI Foot valve unit, suitable for 100mmbore conforming to IS-4038 including nuts ,bolts and washersetcfixing the same to the suction pipe for suitable depth in the UG sump ofthe pump set complete all as specified and directed. 21 M&L for valve chamber and construction of brick masonarry new valve pit chamber of size 1200mmx1200mmx1200mm (internal ) size 100mm thick PCC 1:4:8 type D2 lean concrete foundation using 40mm graded stone aggregate providing well burnt brick masonary wall of 23mm thick built in CM 1:6rendering in cement 1:6 finished even smooth using extra cement internally and 20mmthickin CM 1:4and finished fair and even supply and fix 3.15 mm thick MS sheet steel cover fixed on 50mmx50mmx6mm thick angle ironframe embbeded in PCC copingwith locking arrangement and 1 Nos 50mm size 4 levers lock with key in duplicate Standard size and MS hold fast and handle made out of 25 x 6mm flat iron appplyingtwo coats of synthetic enamel paint of approved shade over a coat of primer (Red Oxide) to all exposed surface making good all disturbed surface to match surrounding complete all as specified and directed. 22 supply and fixing Air release Valve Cast Ironwith two air Outlets, 100 mm dia bore and fixing Up in cast iron water supply mains, complete all as specified and as directed. 23 Supply fabrication and and erection structuarl steel workmade out of angle iron channels flats etc by riveted bolted or welded in built up section trusses in and including cutting hoisting fixing in position and applying two coat of wether proof synthetic enamel paint over a primera coat of anti-corrosive primer of approved colour suitable for base platform of 50000 ltr Smc watertank complete all as specified and as directed . 24 Supply & fixing of sintex SMC panel tank capacity 50000Ltrsquare type, made out of HOT PRESSMOULDED SHEET MOULDING COMPOUND panelsof size 1005mm x 1005mm x 75mm (flange), 1005mm x 2010mm x 75mm (flange) and 1005mm x 502mm x (flange) the flange should be perpendicular to the main surface. The shape shouldbe Trunked type for extra strength and 90 degree flanges pre drilled for bolting. All the Flanges of the 1 mt Panel should have 13 Nos. holes per sidefor fastening/joining the panels to one another. Hot Pressed Moulded SMC Pre Drilled Corner Pieces with built-in ribs of the size 75mm x 75mm should be provided for 90 degree joints of tanks wall to roof jointscomplete with olive green nuts, bolts and washers. Special sealent having excellentUV Resistance as well as suitable for portable water, complete with top covered construction having man hole with cover dia 600mm and internal FRP Ladder.The SMC Panelmust be ISI marked meeteing BIS 14399(part 1 & 2).Tank inlet and outlet size 80mm dia for connection of GI pipe all as specified and directed.(Make - Sintex or equivalent make as approved by GE) including cross arms works panel hight from grond level to 20feet all as directed at site. Note-:Structural work like cross arms, bracings etc shall bemeasured and paid separetlly . 25 Supply, installation, commissioning and testing ofservo controlled Voltage Stabiliser fully automatic operation, unbalanced type (individual phase control), copper wound 415 V, 50 Hz confirming to BIS 9815 : Part 1 : 1994 reaffirmed 2009, IP-45, three phase naturally oil cooled, indoor type & designed for input variation between 300 volts to 480 volts with output voltage stabilised at 415 volt with accuracy ±1.0% and speed of correction 15 volts per second of capacity 100 KVA including first filling of transformer oil having dielectric strength not less than 150 KV as per IS:335, 0-500 volts voltmeter, arrangment to check input voltage and output voltage, RYB indication lamp, high & low voltage cut off system, single phase preventor, time delay relay, servo byepass switch, overload & short circuit trip system, ammeter, oil level gauge& capacity overload 20% overload for one hour etc.,completeall as specified & directed 26 Supply,install,testing and commissioning outdoor type step down transformer 11000 volts/433 volts (at no load) ,AC , 3 phase 50Hz capacity 100 KVA corec type double copper wound , oil immersed , naturally cooled, oil natural, air natural (ONAN) with external cooling fins , delta connected on primary side (HV) ) star connected on secondary side (LV) in accordance with vector symbol , Dyn 11 (vector group) with neutral brought out on secondary side (LV side) and having tapping at +5% to -10% (at 2.5% each step) HV side to be changed by means of hand operated off load tap changer gear. The Transformer shall be IS 1180Part 1:2014 (level -2) and BEE certied and shall comprise of the following :- (a) cable end box on HT side suitable for 95sqmm 3 core XLPE cable (b) cable end box on LV side suitable for 150sqmm 3.5 core XLPE cable (c)Oil conservator with filter type frain valve and oil level gauge (d)dehyderating breather with first fill dehyderating agent (silica gel)(e) explosive vent(f)Thermometer pocket on tank cover(h) Two earthing terminals on tank cover to facilate fixing of 32x6mm copper earth strip for earthing of neutral body. 27 (g)one no 100mm dia , dial type thermometer , vapour pressure type , having range 0-120 degree celcius with metal guard having maximim perimeter reading , temperature indicator with resisting device for transformer. (i)Rating plate and terminal making plate (j)oil level gauge (k)oil drain/filter valve(l) lifting lugs (m) Oil filling hole with cap / plug with connecting plate complete (n) air release valve plug(o)Four plain solid cast steel deattachable rollers(p)extra bushing for neutral , outside the LT cable box for providing independent earthing for Neutral(q)First filling of new and unused transformer oil IS:35/93(4th revision), marked (Make:Savita/Poweroil) filtered and tested upto 40KV dielectric strength at 2.5mm air gap between testing. 28 Supply , installation, testing and commissioning ofLT Panel outdoor typefabicrated of 3.15mm thick CRCA sheet dust and vermin proof powder coated double door type independent cabin including locking arrangement for each MCCBs, bus bar rated 400 Ampenclosed complete suitable for operating on 415 volt 50 Hz AC supply internally wired with copper conductor/strip of adequate size from main incoming MCCB to bus bar and bus bar to outgoing MCCB/MCBs having legs 45cm made out of 65x65x6mm angle iron grouted on brick masonary platfor upto 30 Cm. Brick masonary platform should be 60Cm above the ground level, comprising the following:- (a) 4 Pole MCCB 25 KA 250 A - 1 Nos(b) Digital Ammeter with CTs& selector switch - 1 Nos(c) Digital Voltmeter & selector switch - 1 Nos(d) 4 Pole MCCB 100 Amp, 50 Hz, 415 V with rupturing capacity 16 KA -03 Nos(e) 4 Pole MCCB 63 Amp, 50 Hz, 415 V with rupturing capacity 16 KA - 01 Nos(f) SPN MCB 40A- 01 Nos.(g) Onload changeover TPN 250 A - 01 No. (h)copper bus bar TPN 250 Amps rating -01 set 29 Angle Lamp holder insulated body with back plate for batten fittings and including one15 Watt LED Bulb non dimmable B-22 cool daylight all as specified and as directed. 30 Supply and fixingEnvironmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head 10 watt 6000 K inbuilt LED luminaire comprising of high brightness LEDs, IP54 protection including connecting electricaly using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm, complete all as specified and as directed. 31 Supplying, installing, testing & commissioning of factory assembled Diesel Engine withdriven generating set coupled withalternator AC to give continuous output of 100KVA at a power factor of 0.8 lagging, 415 volts, AC, 3 phase, 4 wire, 50 HZ, 1500 RPM, directly coupled with diesel engine, watercooled, mounted on common base frame complete with in built fuel tank (service tank) of adequatecapacity with fuel line, built in electronic governor & accessories, PCC foundation work as per manufacturers instructions, vibration damper pads,control panelshowing all parameters of engine & alternator, sound proof canopy & other accessories etc. and confirming to the under-mentioned technical specifications confirming to BS:5514 & IS 10000 complete in all respect with following accessories, parts all as specified & directed.(a) DIESEL ENGINE :4 cylinders , turbo charged watercooledat 1500 RPM under NTP conditionsIS 4722, BS 5000, IEC 3411, ISO 8528, BS 5514, ISO 3046, conforming to with an overload capacity of 10% for one hour in 12 hrsof continuousoperationwith the following accessories 32 (i) Radiator with blower fan or heat exchanger with guard .(ii) Pipe coupling for engine cooling system piping (iii) Corrosion inhibitor coolant(iv) Paper element filters-(i)Fuel(ii) Lube oil(iii) By Pass(vi) Fly wheel housing and fly wheel to suit (vii) Engine bearing mechanism in fly wheel housing (viii) shut off coil with safety for LLOP /HWT./ Over speed.(ix) Dry type air cleaners and vacuum indicators .(x)Residentialsilencers.(xi)Stainless steel exhaust flexible bellows.(xii)Motor driven priming pump.(xiii) Electric starter.(xiv)Battery charging alternator.(xv) Exhaust piping made outof STICC class MS Pipe inclusive of all accessories and hardware , necessary supportas per manufacturer’s recommendations to sustain back pressure with rain cap(xvi) Mineral wool insulation 2 inch thick covered with aluminium sheets of 30 gauges for the entire length of exhaust pipe.(xvii) First fill of oil coolant and diesel during commission and 12 hours testing.(xviii)Interconnecting copper cabling of adequate capacity between batteries andcontroller.(xix) Fuel pipe. Fuel Tank_ 24 hours full load diesel storage capacity inbuilt fuel tank with mounting brackets factory fabricated made of MS sheet with level indicator fuel inlet , fuel outlet , air vent, drain plug,inlet arrangement filling from exterior of canopy etc. 33 (xx) Battery :- 150 AH,12 Volts maintenance free battery of Qty-2 Nos with leads and terminal. (xxi) PCC Foundation :- Civil work and PCC foundation for installation DG Set as per manufacturers instruction.(b) ALTRERNATOR : 100 KVA at 0.8 PF lagging, 415 volts, 3 Phase, 4 wire, 50 Hz at 1500 RPM self excited and self regulated with AVR brushless excitation band of voltage ± 1% of rated voltage from no load to full load insulation class H, IP-23 self ventilated and conforming to IS4722, BS5000, IEC 34/1, ISO 8528, BS5514, ISO3046, suitable for above mentioned diesel engine complete all as specified and directed . (c) ACOUSTIC ENCLOSURE : Factory made acoustic enclosure (canopy) 100 KVA DG set to reduce noise level to 75 db (A), measuredat 1.00, meter distance @75% load auditable frequencies as per guidelines of CPCB & comprising of following-:(i) Sound proof insulation 100mmthick Rock wool (Density 65 Kg/cum) (ii) Outer body: Not less than 1.6 mm thick CRCA. (iii) Door 1.6 mm thick CRCA(iv) Inner surface: 1.0 mm thick powder coated & perforated CRCA / GI sheet (v)Common base frame: ISMC 250 34 (d)AMF CONTROL PANEL :LT panelmadeout of 2mm thick CRCAsheets in suitable compartmentsfront openable duly powder coated for a weather proof and long lasting finishing including the following:- (i) MCCB suitaibly rated ,qty OEM recommended(Make: Legrand/Havells/L&T).(ii) contactor of suvitable size of 2 Nos. Set of phase indicating lamps with HRC fuses - 01 Set.(iii)Voltmeter 96 sq.mmdigital type 0 to500 volts rangewith selector switch: 01 set(iv) Amp meter 96 sq.mmdigital type 0 to 400 Amps range with suitable CTs complete - 01 set.(v) KWH meter digital type (vi)Digital PF meter (vii) Set of suitable CT”s(viii) Indicating lamps for supply and load on (ix)Instrument fuses (HRC type)(x) Bottom gland plates for incoming and outing cable(xi)Circuit diagram plateNOTEl: Testingh of DG Set must be done on ground by the contractor as per ground execution requirment and providing the fuel and heat load is tested by the machine for minimum of 24 Hrs. 35 Cleaning of site by way of bush cutting for operating theSuitable truck Mounted DTH drilling rigs along with accessories etc to the site of work & erecting of rig including leveling for required area for starting the job workall as specified & directed 36 Provision of trial bore hole /well of size less than 250 mm dia size pilot bore through any kind of soil/strata including hard dense stone /boulder by means of direct rotary method below ground level upto 150meter depth complete all as specified and directed by Engineer in charge.Note :- 1. The depth of trial boring of the tube well at the site indicated by the Eng-in-charge is anticipated to be 120 meter below ground level. 2. The depth may, however be ordered in writing to be varied by the Eng-in-charge up to a maximum of 25 %/150 mtr of the above mentioned depth (plus or minus). 3. If the Eng-in-charge decided that suitable water bearing strata is not available in the aforesaid bore or the boring cannot be continued further on account of the type of strata ,4c Further Eng-in-charge may order the contractor to bore at other site(s) 5. Eng-in-charge shall give three no. of directionto the contractor for trial hole/well of size less than 250mm dia.6. No any extra charge to be provided to contractor 37 M & L for reaming of developmentbore by reaming of 250mmfor 60 RM from ground level complete all as specified and directed. 38 M & L for Reaming of development bore from depth exceeding 60 metre to 120 meter of dia 250 mmcomplete all as specified and directed. 39 Supply ,assembling including jointing lowering and fixing MS ERW blind pipe200 mm dia and thickness 8mm including all fittings and fixtures upto 100m deep complete all as specified & directed. 40 Supply ,assembling including jointing lowering and fixing slotted MS ERW pipe 200 mm dia and thickness 8mm including all fittings and fixtures complete all as specified & directed. 41 M&L for strata sample (at every 6 meters depth) one set in suitable box pattern, earth sample strata should be produced as per IS and submitted to the department. The box shall be 2nd class hard wood with suitable locking arrangement etc complete all as specified and directed. 42 M&L for borewell chart on acrylic sheet of size 60 cm x 15 cm duly marked permanent marking including 12mm thick plywood frame, clamps for fixing on wall etc all as specified and directed. 43 M&L for development of tubewell by means of over puming high velocity jetting with 600 PSI Air compressor all as specified in IS 8110-2000 PARA 4.3 including arrangement for equipment fitting and supplyl of sodium hepta sulphate 60 kg complete all as specified & directed. 44 All asper Sl item no 8.23 above but by means of over pumping muddy water for subsequent hours until clear discharge as per clause 9.3 of IS 2800(Part-1)-2009 complete all as specified and directed. 45 Collection of sample of water and conduct testing in Govt lab for all parameters (Chemical and Bacteriological Tests) of water to assess the potability and submit the report complete all as spcified and directed. 46 Supply & Fixing of MS well cap for 200mm dia of thickness 8 mm of pipe at the top of casing pipe of bore well with locking arrangement complete all as specified and directed. 47 Supply & packing of pea gravel 20mm to 25mm size of approaved quality as ordered to packed around the casing pipe/slotted pipe in the bore well to entire depth complete all as specified & directed 48 Supply & Fixing MS flat Iron clamp 100mm x 10mm thicksize clamp fixed with 16mm dia nut bolts and washers 2 on both sides of clampfor holding 65mm MS column pipe,2Noscomplete all as specified and directed. 49 Supply, installation, commissioning and testing of submersible pump setof capacity 15 HP ,electric driven, 415 volts discharge430 LPMat 135 mtr headwith CI Impeller, CI diffuser, EN-8 shaft, stainless steel stainer comprising with suitable capacity of Electric motor designed for working on 415 volts, 3 Phase, 50Hz, filled with oil for effective cooling and life long lubrication of heavy duty ball bearing and mechanical seal complete with Digital electronic softstardelta starter of suitable capacity includidfitted on suitable size panel board included with & including protections against over load, single phase, phase seque nce reversalcomplete all as specifed and as directed. Note: the capacity od Submersible pump may be change as per depth of borewell for required yield of water. No extra payment shall be made to contractor. Note:- 1. Rate quoted by contractor deemed to be inclusive for the cost for calculating the capacity of submersible pump set . In this regard a certificate along with the copy of the design of the pump by manufactrer shall be furnished by the contractor for suitability of the motor for selected pump suitable for bore as to deliver continuous water with stable LPM. 2. Rates quoted by contractor deemed to be inclusive of one set of submersible pump and conected items are installed in borewell and one set of submersible pump and connected items as stand by. 50 M&L for provision of MS Tie rod for anchoring of submersible pump set fabricating out ofIron rod of size 8 to 10 mm, 2 Nos. vertical to hold the submersible pump set alongwith column pipes, length suitable to length of submersible pump set including suitable nut bolts and washers including tail piece of size 65mm of 1mtr length having one side flaged end and other end threaded for fixing with submersible pump including two Nos suitable size welded Flat Iron 40mmx6mm size with holes for fixing of tie rod complete all as directed. 51 Supply and fix PVC insulated and PVC sheathed multi stranded copper conductor cable for submersible pump set, ISI marked, conforming to IS-864 of size 3 core 10 Sqmm, 1100 volts grade, including necessary water proof connection to submersible pump at cable lead complete all as specified and directed. 52 Supply & Fixing pipe GI tubing heavy grade 80 mm bore duly welded flanged (thickness of flange 12mm having 04 holes) with and including rubber packing of 6mm thick, nuts, bolts, washers complete in 3 mtr length as column pipe in bore well complete all as specified and directed. 53 Supply and lowering stainless steel V wire screen 150mm dia, K type packet(wall thickness should not be less than 8mm), with opening 0.50mm, inside the tube well assembly in the manner with top of the packet resting on the lowermost end of the assembly complete all as specifed & directed.Note:-1. The Screen pipe shall be lowered as per requirement of the borewell at desired depth inside the MS casing pipe.2. Screen pipe shall be lowered as to hang with the end of MS casing pipe lowered. 54 Supply & fixing suitable casing drive shoe for 200mm dia and bit tube as per requirement of depth or ODEX attachment all as specifed & directed by Engr -in-charge.
