Tender For Item Rate Contract For Miscellaneous Civil Maintenance Works Under Gail Samakhiali, Kandla And Nasirabad Region For Two Years; Providing Services of 01 no of resource (semi-skilled) on 8 hours basis at IPS NASIRABAD, GAIL TOWNSHIP AJMER & RT TABIJI EARTH WORK 1 Earth work in excavation in foundations, trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, disposal of excavated earth, lead upto 50 m and lift upto 1.5 m disposed soil to be levelled and neatly dressed .a) all kinds of soil. M3 2 242.65 485.30 2 Filling of available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 mtr and lift upto 1.5 mtr. M3 2 182.71 365.42 3 Surface dressing of the ground i/c removing vegetation, grass and in equalities upto 15cm average depth and disposal of rubbish lead upto 50 m and lift upto 1.5 m. All kinds of soil M2 10 31.83 318.34 4 Supplying and spreading of good earth at site i/c roylty and carriage upto 5km(earth measured in stacks will be reduced by 20% for payment) M3 40 796.00 31840.00 SUPPLY OF MACHINERY 5 Supplying the JCB with driver, cleaner, fuel/diesel & other consumables etc. as and when required. HR 6 1525.42 9152.54 6 Supply of tractor with trolly OR with cultivator OR leveller equipment/machinery & including driver, diesel & consumables required for performing day to day jobs, for 08 hours per day basis or prorata basis.labours will paid separately through the concerned item. DAY 1 1707.73 1707.73 7 Supplying Dewatering Pump set of capacity 7000 litres/hour with experienced operator for cleaning of sanitary inspection chambers & Septic tanks located at GAIL Premises, rate includes transportation of pump , operator, tools, tackles and fuel etc. HR 5 1073.35 5366.74 CONCRETE WORK 8 Providing & laying cement concrete in footings & bases for columns, kerbs, steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:3:6 (1 Cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) M3 3 6800.08 20400.25 9 Providing & laying cement concrete in footings & bases for columns, kerbs,steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:2:4 (1 cement: 2 coarse sand : 4graded stone aggregate 20 mm nominal size). M3 4 7344.30 29377.19 10 Reinforced cement concrete work in walls (any thickness), including floors, roofs, attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : with 1:1.5:3 (1cement: 1.5 Coarse sand(Zone-3): 3 graded stone aggregate 20 mm nominal size.) M3 1.7 10117.07 17199.01 11 Centring and shuttering ic strutting and propping etc.and removal of form work in all types of cement concrete and R.C.C. work for all levels. M2 22 365.56 8042.33 12 Reinforcement for R.C.C., work including cutting bending, binding and placing in position complete for all levels. a)Thermo Mechanically Twisted bars Fe500D or more. KG 50 100.54 5026.86 13 Dismantling cement concrete floor/Cement concrete pathway,bitumineous road, & R.C.C. etc. of any mix i/c stacking of serviceable material within 50 meters lead & disposal of rubbish to the dumping area away & outside the premises. M3 1 2269.20 2269.20 MATERIAL SUPPY 14 Supplying & Stacking of Red sand stone gang saw cut 30 mm thick (exposed face fine dressed with rough backing) as per direction of EIC. M2 4 662.86 2651.44 15 Supplying and stacking of graded stone aggregate 20 mm at site/ all the locations of work within the premises. M3 2 1802.63 3605.25 16 Supply & stacking of coarse sand (approved quality) at site/all the locations of work within the premises. M3 2 1834.25 3668.50 17 Supply & Stacking of Portland Cement (OPC-43 Grade) of apprvoed brand at site which shall be in the form of newly filled bags of 50 kg capacity. Item includes all the charges like cost of cement, transportation, loading, unloading & other overheads as applicable. KG 250 6.78 1694.90 LABOUR SUPPY 18 Providing services of semi skilled nature of manpower like, mason/ carpenter/painter/plumber/ welder etc. on 08 hours per day basis with required tools & tackles. DAY 10 739.00 7390.00 19 Providing services of Unskilled nature of manpower on 08 hours per day basis with required tools & tackles. DAY 20 655.00 13100.00 BRICK WORK 20 Brick work with bricks of class designation 75 in foundations & plinth in 1:6 cement mortar(1 Cement : 6 Coarse Sand). M3 1.5 6648.65 9972.97 21 Brick work with bricks of class designation 75 in super structue for all floor levels in 1:6 cement mortar (1cement :6 coarse sand) M3 1.5 8488.52 12732.78 22 Half brick masonry in Cement mortar 1:4 (1 cement :4 coarse sand) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level. M2 2 1047.60 2095.20 23 Brick pitching by Flush / Ruled/ Struck or weathered pointing with cement mortar 1:3 (1cement: 3fine sand) half brick thick, including supply of bricks and preparing the surface complete With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. M2 5 840.28 4201.40 FINSHING WORK 24 Providing cement plaster on the wall surface: 12 mm thick plaster in 1:6 CM (1 cement :6 coarse sand ) M2 20 320.35 6406.98 25 Providing cement plaster on the wall surface: 12 mm thick cement plaster of mix 1:4(1 cement : 4 coarse sand ). M2 6 333.12 1998.72 26 Repairs to the plaster in patches or replastering as per the existing thickness i/c cutting , dismantling old plaster or skirting , the patch in proper shape and raking out the joints , applying the cement slurry and plastering the surface of the wall complete for all floor levels i/c necessary scaffolding etc. and disposal of the rubbish to the dumping ground within 50 m lead with cement mortar 1:4 (1cement : 4 fine sand) M2 20 510.28 10205.67 27 Stone work (Machine cut edges) for wall lining etc. (Veneer work) upto 10 meter height backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1white cement: 2 stone dust) with an admixture of pigment matching the stone shade, to be secured to the backing and the sides by means of cramps & pins as per requirement and direction of EIC. Red/White stone slabs 30 to 40 mm thick. M2 4.5 5051.80 22733.09 28 Providing and applying plaster of paris including putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. M2 8 244.89 1959.10 29 Distempering with 1st quality acrylic distember (Ready mix)having VOC content less than 50 grams/ litre of approved brand and manufacturer and of stated shade and colour by SIC/EIC on old work to give an even shade ( Two or more coats) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. MAKE:(Asian paints- Tractor UNO or equivalnet). M2 550 58.45 32146.74 30 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of stated shade and colour by SIC/EIC complete, as per manufacturers specification i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.Three or more coats on new work. MAKE:(Asian paints- Tractor UNO). M2 20 173.06 3461.24 31 Painting with synthetic enamel paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work ( two or more coats ) for wood/ steel work i/c necessary scrapping if any, for all shades. M2 40 95.83 3833.19 32 Painting with synthetic enamel paint of approved brand and manufacture and of required shade to give an even shade for wood/ steel work i/c necessary scrapping if any, for new work (Three or more coats) M2 12 210.91 2530.91 33 Finishing walls with Acrylic Smooth exterior paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work (Two or more coats applied @ 0.90 ltr/ 10sqm). i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 95 112.56 10693.44 34 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Three or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 25 149.71 3742.76 35 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm ( Asian Royale or equilent) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 0.5 208.44 104.22 36 Painting with aluminium paint of approved brand and manufacture to give an even shade (one or more coats on old work). M2 15 89.49 1342.36 37 Relettering with black japan paint or with required shade of paint of approved brand and manufacturer. per letter per CM height 350 3.59 1256.13 38 Lettering with black japan paint or with required shade of synthetic paint of approved brand and manufacturer. per letter per CM height 125 5.73 716.62 FLOORING 0.00 39 Grinding & polishing of terrazzo / kota /marble/granite etc. flooring with rubbing machine, hand grinder, 1st class mason & all required tools / tackles consumables (polish) etc. on 08 hours per day basis, complete as per direction of EIC. Payment shall be made on the basis of actual working hours on prorata basis. Day 2 1474.99 2949.98 40 Providing and fixing 1st quality ceramic glazed floor tiles/wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including spacer bar in between the tiles & grouting with pigment of matching shade/ as desired by EIC/SIC complete. including removing the broken tiles and raking out the old under layers and apply cement slurry complete. M2 3 1037.25 3111.76 41 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. M2 1 2862.82 2862.82 42 Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete .Size of Tile 60x60 cm M2 10 1448.12 14481.18 STEEL WORK 0.00 43 Provoding & Fixing pressed steel door frames of profile B confirming to IS:4351 manufactured from commercial mild steel sheet of 1.6mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle section 50x25 mm, or base ties of 1.6 mm pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. press butt hinges, 2.5mm thick with mortar guards, lock strike plate and shock absorbes as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by EIC. Fixing with adjustable lugs with split end tail to each jamb. M 8 543.75 4349.99 44 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) sections of any shape & size., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete at any height. Hot finished seamless type tubes. KG 50 192.36 9617.92 45 Steel work riveted, bolted or welded in built up sections / framed work of any shape and size including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer using structual steel etc as required in landings of stair case, gratings, shutters frame andsteel window, rolling shutter, collispal gates frames, gates including windowgrillsand similar works at any height (Angle, tea, flats, channels, MS pipes, plates etc.). KG 50 124.63 6231.72 DOOR & WINDOW FRAME & SHUTTER/ CUP BOARD SHUTTER ETC. 0.00 46 Supply and fixing G.I. wire mesh of approved quality. to windows & wooden frame/shutter using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm and necessary screwsnails including refixing of the existing beading and necessary painting if any. Item includes removal of defective wire mesh (only area of mesh to be measured). M2 2 1219.64 2439.27 47 Providing and fixing glazed shutters for doors, windows, clerestory windows using 4.00 mm thick glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. Item includes removal of defective shutters if any. IInd class teak wood 35 mm thick. M2 1.5 4605.23 6907.84 48 Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (over all area of the shutter to be measured) worn out shutter to be deposited in the civil store, after taking out. M2 1 2024.82 2024.82 49 Providing and fixing Sainless steel SS304 curtain rod having wall thickness of 1.20mm with two SS 304 brackets fixed with SS screws and PVC sleeves etc., wherever necessary complete : 20 mm dia M 3 236.56 709.67 50 Providing and fixig bright finished brass 150 mm mortice latch and lock, ISI mark with six levers and a pair of anodised aluminium lever handles of approved quality with necessary screws etc complete i/c taking out the old damaged one if any. Brand :Harrison/PLUS POINT EA 8 932.20 7457.56 51 Providing and fixing aluminium die cast section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Brand : Hardwyn/ozone EA 7 1048.58 7340.06 52 Renewal of old putty of glass panes (length) M 50 52.34 2617.14 53 Providing & fixing fly proof wire gauge to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire Gauge with 0.63 mm dia. Wire and 1.4mm aperture on both sides. M2 4 787.43 3149.70 ALLUMINIUM WORK 54 Repair & maintenance of aluminium doors (any size) for smooth opening & closing of door including replacement of missing aluminium round shape or tubular handle, renewing rubber/ neoprin gasket, missing screws, aluminium strip for holding glass etc. Quantity on door basis of all sizes, any other required item to be brought & replaced but will be paid separately. EA 3 2658.62 7975.86 55 Repair & maintenance of aluminium windows for smooth opening & closing of window including replacement of defective hinges, missing aluminium handles, renewing rubber / neoprin gasket, missing screws etc. Quantity on window basis required for all sizes, any other required item to be brought & replaced but will be paid separately. EA 4 813.99 3255.97 56 Providing & Fixing / Renewing Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading). With float glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. M2 4 1403.19 5612.75 57 Providing & Fixing / Renewing Tuffened glass Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading) with tuffened glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. Brand:- Saint globin, Modi guard M2 6 1610.16 9660.93 58 Providing & fixing double action hydraulic floor spring of approved brand and manufacture cofirming to IS: 6315, for aluminium doors, including cost of cutting floors as required, embedding in floors and stainless steel cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. With stainless steel cover plate minimum 1.25 mm thickness complete as per direction of the EIC. EA 3 2632.38 7897.14 59 Providing & Fixing Neoprin/EPDM rubber gasket replacing for alluminium glazed doors & Windows (exiting rubber gasket) including racking out the old putty, removing glass and refixing the same properly. Brand:- RAMSON M 100 110.17 11016.85 WATER SUPPLY PIPING 60 Providing and placing on terrace (at all floor levels) polyethylene Circular water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.complete including taking out old one and shifting in civil maint. Store. L 1000 10.25 10254.15 61 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15mm dia nominal bore M 5 300.31 1501.53 62 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore M 5 343.61 1718.04 63 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore M 8 436.03 3488.27 64 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore M 3 575.21 1725.63 65 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore M 3 710.47 2131.42 66 Making connection of G.I. distribution branch with G.I. main 25mm to 40mm nominal bore by providing and fixing tee including cutting and threading the end of pipe, necessary excavation & backfilling etc. complete. EA 2 850.07 1700.14 67 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. b) 20 mm outer dia. M 10 255.70 2557.01 68 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. c) 25 mm outer dia. M 10 331.30 3313.02 69 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. c) 40 mm outer dia. M 15 524.87 7873.09 SANITARY FITTINGS 70 Providing and fixing white vitreous china flat back/ovel wash basin of required colour with C.I. brackets, pair of 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including making all connections, cutting and making good the walls wherever required including taking out the old damaged one & depositing in the civil store if any. Wash basin of size 630x450 mm. EA 1 2469.24 2469.24 71 Providing and fixing white viterous china flat back or wall corner type lipped front urinal basin of standard/ existing size (430x260x350mm or 340x410x265 mm sizes respectively) and required colour with C.P. flush pipe, C.P. couplings, spreaders, unions, clamps and waste fittings including cutting and taking out the old damaged one to deposit in civil store if any. EA 1 1537.14 1537.14 72 Providing and fixing white vitreous china water closet squatting pan (Indian type) of required colour with 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) all fittings & fixtures required to connect with the cistern and including making good the walls & floors by C.C. 1:2:4 or C.M. 1:4 as required. Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store. Orrisa Pattern W.C. pan of 580 x 440 mm. EA 1 6308.54 6308.54 73 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow rrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store.: W.C. pan with ISI marked white solid plastic seat and lid. EA 1 7463.71 7463.71 74 Providing and fixing 10 litre capacity low level PVC flushing cistern of approved make and required colour with manually controlled device (handle lever) confirming to IS: 7231, with all fittings and fixtures complete including taking out the old damaged one if any, depositing in the civil store. EA 3 1109.92 3329.75 75 Providing & fixing complete kit including all fittings, syphon,washer etc. for low level PVC cistern of approved quality i/c taking out the old damaged/ broken one if any to deposit in civil store. EA 5 331.76 1658.79 76 Providing and fixing solid plastic seat with lid of approved quality, required size & colour for pedestal type W.C. pan with hinges rubber buffers etc. completed I/c taking out the old damaged one if any to depositing in the civil store. Solid Plastic seat with lid of requiered size & colour. EA 2 638.41 1276.83 77 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (Push/ Rotating type) 15mm nominal bore EA 10 535.36 5353.60 78 Providing and fixing C.P. brass long /Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore Brand:- Hindware / cera /jaquar EA 8 932.20 7457.56 79 Providing and fixing C.P. brass long nose bib cock/ Pillar cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore EA 8 765.05 6120.42 80 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge. EA 2 964.64 1929.27 81 Providing and fixing PVC Connection pipe of approved quality with unions & other fittings for Geaser or wash basin-45cm or required length including dismantling of old and damaged one for 15mm nominal bore. EA 6 91.12 546.73 82 Providing and fixing semi rigid/flexible PVC waste pipe of approved quality with union, coupling & other necessary fittings for wash basins and sinks (upto 40mm dia.) including dismantling the old damaged one if any. EA 6 111.44 668.66 83 Providing and fixing P.T.M.T. liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. EA 1 156.94 156.94 84 Providing and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. a) 15 mm to 25 mm dia EA 10 86.42 864.24 85 Supply and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. b) 32 mm to 50 mm dia. EA 10 288.82 2888.22 86 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end), Nominal bore from 20 mm to 50 mm including removing the old and damaged one if any. Brand:- ZOLOTO/Leader/ Ruhe EA 5 661.01 3305.06 87 Providing and fixing Float/ ball valve set 15/20/25mm nominal bore of approved quality with rod etc. complete (High or low pressure with plastic floats) for over head water tanks complete including removing the damaged one if any. Brand:- SUPREME/RELISE EA 8 414.32 3314.59 88 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. (Item include Cost of Dismantaling, Removing and all labour, material required to complete removing and installation work.) EA 3 660.88 1982.64 89 Providing and fixing P.T.M.T. waste coupling for wash basin and sink of approved quality, colour and make. a) Waste coupling 31 mm / 38 mm dia. EA 3 110.79 332.37 90 Providing and fixing 8 mm dia C.P. / S.S. Jet or hand health faucet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. EA 4 325.48 1301.90 91 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 75 mm dia M 15 109.51 1642.71 92 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 110 mm dia M 15 203.39 3050.79 93 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including fixing & painting of all fittings and brackets, cutting and making good the walls wherever required and return the old wash basin in civil store:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer EA 1 4461.21 4461.21 OTHERS MISCELLAEOUS ITEMS 94 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. EA 3 1498.92 4496.77 95 Providing & Fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated J or L hooks, bolts & nuts 8mm dia. G.I. plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confirm to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat. M2 5 1161.19 5805.94 96 WATER TANK CLEANING -Cleaning of over head water tanks below 5000 litre capacity. EA 6 350.23 1910.37 97 Providing & Fixing G.I. Chainlink Fabric Fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-In-Charge. a)Made of G.I. wire of dia. 4 mm. M2 10 948.79 9487.88 98 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. sqm 10 974.75 9747.50 99 JOBS BASED ON (DSR - 2023): Estimated cost of DSR items is Rs.30,000/-. DSR-2023 at which contactor shall execute any work which is mentioned in DSR - 2023 as per requirement and need to keep GAIL premises maintained during the contract period. Any item covered under the DSR-2023 and as directed by EIC (Engineer-in-charge). Note : Payment for those items which are not available above in SOR shall be regulated as per DSR - 2023. It is further clerified that only those items of DSR - 2023 shall be operated which are not given above i.e. in any item of entire SOR of this contract. EA 30000 1.00 30000.00 100 Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.(Structural frame work including M.S. plate to be providedseparately. Rectangular area of the sheet only shall be measured forpayment). Overhead informatory road signage M2 1 5481.21 5481.21 101 Removal old & fixing of new Sun film including proper dispose of the removing material as per the instruction of EIC M2 10 508.47 5084.70 102 Providing and applying polyether based polyurethane (PU) waterproof coating consisting of two components (resin + hardener) in four coats consisting of a primer adhesion quote and three ceiling quotes applied by brush evenly to perfect level @ minimum 160 gram/square metre/coat over RCC slab including sprinkling the last coat of P.U. with a layer of clean sand 300 micron and laying minimum 50 mm thick PCC (1:2:4) over the fully cured coating in panels of Max 1.2 m X 1.2 m with 24 SWG chicken wire mesh finished smooth and sealing joints between panels with polysulphide sealant as per approved manufacturer specification and including preparing the base surface (levelling, cleaning, filling up cracks with thin paste of polyurethane filling compound) providing fillets of 75 mm radius with PCC (1:2:4) at junctions of horizontal and vertical surface continuing the waterproofing on the vertical face to a minimum height of 150 and an over finish roof surface terminating it in continuous groove of 10 mm×20 mm and filling with polyurethane sealent putty continue in the treatment into rainwater outlet by providing 450 mm× 450 mm at all outlets levelled down by minimum 25m finishing all complete.Cement supplied by the contractor at their cost M2 5 889.82 4449.10 IPS NASIRABAD EARTH WORK 1 Earth work in excavation in foundations, trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, disposal of excavated earth, lead upto 50 m and lift upto 1.5 m disposed soil to be levelled and neatly dressed .a) all kinds of soil. M3 5 242.65 1213.25 2 Filling of available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 mtr and lift upto 1.5 mtr. M3 5 182.71 913.55 3 Surface dressing of the ground i/c removing vegetation, grass and in equalities upto 15cm average depth and disposal of rubbish lead upto 50 m and lift upto 1.5 m. All kinds of soil. M2 50 31.83 1591.72 4 Supplying and spreading of good earth at site i/c roylty and carriage upto 5km(earth measured in stacks will be reduced by 20% for payment) M3 40 796.00 31840.00 5 5.1 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1.2 M above ground level , wild bushes of any height and removal of rubbish upto a distance of 50 m outside the boundary wall as directed by EIC.NOTE If grass will cut only upto ground, dump more than 50 m away from boundarywall outside and only uprooting will not be done than only 60% of the measurement wil be paid. M2 58000 16.41 951584.66 5.2Weed Killer Liquid for Terminals and Lawn for killing of unwanted weed and grass in terminal area between concrete floor joints and paver block joints Kg 10 1525.42 15254.24 SUPPLY OF MACHINERY 6 Supplying equipment/machineries on supply/hire basis including operator, consumbale including fuel and transportation 6.1 Supplying the JCB with driver, including fuel/diesel, helper & other consumables for JCB etc. as and when required. HR 20 1525.42 30508.47 6.2 Supplying the Hydra/crane up to 15T with driver, helper, fuel/diesel & other consumables for hydra/crane etc. as and when required. HR 5 1525.42 7627.12 7 Supply of tractor with trolly OR with cultivator OR leveller equipment/machinery & including driver, diesel & consumables required for performing day to day jobs, for 08 hours per day basis or prorata basis.labours will paid separately through the concerned item. DAY 10 1707.75 17077.50 8 Supplying Dewatering Pump set of capacity 7000 litres/hour with experienced operator for cleaning of sanitary inspection chambers & Septic tanks located at GAIL Premises, rate includes transportation of pump , operator, tools, tackles and fuel etc. HR 2.00 1073.35 2146.69 CONCRETE WORK 9 Providing & laying cement concrete in footings & bases for columns, kerbs, steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:3:6 (1 Cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) with Minimum 7 days curing M3 10 6800.08 68000.83 10 Providing & laying cement concrete in footings & bases for columns, kerbs,steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:2:4 (1 cement: 2 coarse sand : 4graded stone aggregate 20 mm nominal size)with Minimum 7 days curing. M3 8 7344.30 58754.39 11 Reinforced cement concrete work in walls (any thickness), including floors, roofs, attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : with 1:1.5:3 (1cement: 1.5 Coarse sand(Zone-3): 3 graded stone aggregate 20 mm nominal size.)with Minimum 7 days curing. M3 8 10117.07 80936.53 12 Centring and shuttering ic strutting and propping etc.and removal of form work in all types of cement concrete and R.C.C. work for all levels. M2 60 365.56 21933.62 13 Reinforcement for R.C.C., work including cutting bending, binding and placing in position complete for all levels. a)Thermo Mechanically Twisted bars Fe 500D or more KG 200 100.54 20107.45 14 Dismantling cement concrete floor/Cement concrete pathway,bitumineous road, & R.C.C. etc. of any mix i/c stacking of serviceable material within 50 meters lead & disposal of rubbish to the dumping area away & outside the premises. M3 6 2269.20 13615.17 15 Providing and fixing upto floor five level precast cement concrete string or lacing coarses, copings, bed plates, anchor blocks, plain window sills, Shelves, Louvers, steps, Staircases, etc., including hoisting and setting in position with cement mortar 1:3 (1cement: 3 coarse sand) including the cost of required centring, shuttering 1:1.5:3 (1cement: 1.5 Coarse sand(Zone-3): 3 graded stone aggregate 20 mm nominal size.) M3 0.5 9419.92 4709.96 MATERIAL SUPPY 16 Supplying and stacking of graded stone aggregate 20 mm at site/ all the locations of work within the premises. M3 5 1802.63 9013.13 17 Supply & stacking of coarse sand (approved quality) at site/all the locations of work within the premises. M3 7.5 1834.25 13756.88 18 Supply & Stacking of Portland Cement (OPC-43 Grade) of apprvoed brand at site which shall be in the form of newly filled bags of 50 kg capacity. Item includes all the charges like cost of cement, transportation, loading, unloading & other overheads as applicable. KG 850 6.78 5762.66 PROVIDING SERVICES OF LABOUR SUPPY 19 Providing services of semi skilled nature of manpower like, mason/ carpenter/painter/plumber/ welder etc. on 08 hours per day basis with required tools & tackles. DAY 70 739.00 51730.00 20 Providing services of Unskilled nature of manpower on 08 hours per day basis with required tools & tackles. DAY 200 655.00 131000.00 BRICK WORK 21 Brick work with bricks of class designation 75 in foundations & plinth in 1:6 cement mortar(1 Cement : 6 Coarse Sand)with Minimum 7 days curing. M3 5 6648.65 33243.24 22 Brick work with bricks of class designation 75 in super structue for all floor levels in 1:6 cement mortar (1cement :6 coarse sand)with Minimum 7 days curing M3 7 8488.52 59419.65 23 Half brick masonry in Cement mortar 1:4 (1 cement :4 coarse sand) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level with Minimum 7 days curing. M2 7 1047.60 7333.21 24 Brick pitching by Flush / Ruled/ Struck or weathered pointing with cement mortar 1:3 (1cement: 3fine sand) half brick thick, including supply of bricks and preparing the surface complete With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 with Minimum 7 days curing. M2 10 840.28 8402.81 25 Random rubble masonry work: Random rubble masonry with hard stone in foundation and plinth or slopes at ground level, surface etc including levelling up with cement morter 1:6 ( 1 cement : 6 coarse sand) with Minimum 7 days curing. M3 3 6815.51 20446.53 FINSHING WORK 25 Providing cement plaster on the wall surface: 12 mm thick plaster in 1:6 CM (1 cement :6 coarse sand )with Minimum 7 days curing M2 75 320.35 24026.16 26 Providing cement plaster on the wall surface: 12 mm thick cement plaster of mix 1:4(1 cement : 4 coarse sand )with Minimum 7 days curing. M2 30 333.12 9993.60 27 Repairs to the plaster in patches or replastering as per the existing thickness i/c cutting , dismantling old plaster or skirting , the patch in proper shape and raking out the joints , applying the cement slurry and plastering the surface of the wall complete for all floor levels i/c necessary scaffolding etc. and disposal of the rubbish to the dumping ground within 50 m lead with cement mortar 1:4 (1cement : 4 fine sand)with Minimum 7 days curing M2 150 510.28 76542.53 28 Stone work (Machine cut edges) for wall lining etc. (Veneer work) upto 10 meter height backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1white cement: 2 stone dust) with an admixture of pigment matching the stone shade, to be secured to the backing and the sides by means of cramps & pins as per requirement and direction of EIC. Red/White stone slabs 30 to 40 mm thick with Minimum 7 days curing. M2 2.5 5051.80 12629.49 29 Providing and applying plaster of paris/ putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. M2 40 244.89 9795.51 30 Distempering with 1st quality acrylic distember (Ready mix)having VOC content less than 50 grams/ litre of approved brand and manufacturer and of stated shade and colour by SIC/EIC on old work to give an even shade ( Two or more coats) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. MAKE:(Asian paints- Tractor UNO or equivalnet). M2 2500 58.45 146121.57 31 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of stated shade and colour by SIC/EIC complete, as per manufacturers specification i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.Three or more coats on new work. MAKE:(Asian paints- Tractor UNO or equivalnet M2 250 173.06 43265.50 32 Painting with synthetic enamel paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work ( two or more coats ) for wood/ steel work i/c necessary scrapping if any, for all shades. M2 250 95.83 23957.41 33 Painting with synthetic enamel paint of approved brand and manufacture and of required shade to give an even shade for wood/ steel work i/c necessary scrapping if any, for new work (Three or more coats including priming coat) M2 50 210.91 10545.46 34 Finishing walls with Acrylic Smooth exterior paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work (Two or more coats applied @ 0.90 ltr/ 10sqm). i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 2500 112.56 281406.37 35 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Three or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 250 149.71 37427.63 36 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm ( Asian Royale or equilent) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 25 208.44 5210.97 37 Finishing walls with water proofing cement paint of approved brand and manufacture and of stated shade and colour by SIC/EIC to give an even shade on old work ( Two or more coats@ 2.20 KG/10 Sq.m) Complete i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 125 70.66 8832.55 38 Finishing walls with water proofing cement paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade for new work (Three or more coats) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 40 108.97 4358.94 39 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even/ required shade on old work of any paint or distemper i/c sand papering, scrapping complete, of required shade ( Two or more coats) M2 70 88.98 6228.46 40 Wall painting with Plastic/ Acrylic emulsion paint of approved brand and manufacture & of stated shade and colour by SIC/EIC i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete., for new work (Three or more coats ) M2 40 168.96 6758.41 41 Painting with aluminium paint of approved brand and manufacture to give an even shade (one or more coats on old work). M2 135 89.49 12081.25 42 Relettering with black japan paint or with required shade of paint of approved brand and manufacturer. per letter per CM height 3500 3.59 12561.33 43 Lettering with black japan paint or with required shade of synthetic paint of approved brand and manufacturer. per letter per CM height 1050 5.73 6019.65 FLOORING/TILE WORK 44 Grinding & polishing of terrazzo / kota /marble/granite etc. flooring with rubbing machine, hand grinder, 1st class mason & all required tools / tackles consumables (polish) etc. on 08 hours per day basis, complete as per direction of EIC. Payment shall be made on the basis of actual working hours on prorata basis. Day 6 1474.99 8849.94 45 Providing and fixing 1st quality ceramic glazed floor tiles/wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including spacer bar in between the tiles & grouting with pigment of matching shade/ as desired by EIC/SIC complete. including removing the broken tiles and raking out the old under layers and apply cement slurry complete. M2 7.5 1037.25 7779.40 46 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. M2 5 2862.82 14314.09 47 Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete .Size of Tile 60x60 cm 0.00 0.00 47.1 Size of Tile 600x600 M2 2 1448.12 2896.24 47.2 Size of Tile 800x800 M2 2 1757.65 3515.31 48 Supplying & Stacking of Red sand stone gang saw cut 30 mm thick (exposed face fine dressed with rough backing) as per direction of EIC. M2 7 662.86 4640.02 STEEL WORK 49 Providing & Fixing pressed steel door frames of profile B confirming to IS:4351 manufactured from commercial mild steel sheet of 1.6mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle section 50x25 mm, or base ties of 1.6 mm pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. press butt hinges, 2.5mm thick with mortar guards, lock strike plate and shock absorbes as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by EIC. Fixing with adjustable lugs with split end tail to each jamb. M 20 543.75 10874.99 50 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) sections of any shape & size., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete at any height. Hot finished seamless type tubes. KG 150 192.36 28853.77 51 Steel work riveted, bolted or welded in built up sections / framed work of any shape and size including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer using structual steel etc as required in landings of stair case, gratings, shutters frame andsteel window, rolling shutter, collispal gates frames, gates including windowgrillsand similar works at any height (Angle, tea, flats, channels, MS pipes, plates etc.). KG 250 124.63 31158.62 DOOR & WINDOW FRAME & SHUTTER/ CUP BOARD SHUTTER ETC. 52 Supply and fixing G.I. wire mesh of approved quality. to windows & wooden frame/shutter using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm and necessary screwsnails including refixing of the existing beading and necessary painting if any. Item includes removal of defective wire mesh (only area of mesh to be measured). M2 7 1219.64 8537.46 53 Providing and fixing glazed shutters for doors, windows, clerestory windows using 4.00 mm thick glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. Item includes removal of defective shutters if any. IInd class teak wood 35 mm thick. M2 4 4605.23 18420.92 54 Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (over all area of the shutter to be measured) worn out shutter to be deposited in the civil store, after taking out. M2 6.5 2024.82 13161.33 55 Providing and fixing Sainless steel SS304 curtain rod having wall thickness of 1.20mm with two SS 304 brackets fixed with SS screws and PVC sleeves etc., wherever necessary complete : 20 mm dia M 50 236.56 11827.75 56 Providing and fixig bright finished brass 150 mm mortice latch and lock, ISI mark with six levers and a pair of anodised aluminium lever handles of approved quality with necessary screws etc complete i/c taking out the old damaged one if any. Brand :Harrison/PLUS POINT EA 10 932.20 9321.95 57 Providing and fixing aluminium die cast section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Brand : Hardwyn/ozone EA 10 1048.58 10485.80 58 Renewal of old putty of glass panes (length) M 250 52.34 13085.69 59 Providing & fixing fly proof wire gauge to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire Gauge with 0.63 mm dia. Wire and 1.4mm aperture on both sides. M2 4 787.43 3149.70 ALLUMINIUM WORK 60 Repair & maintenance of aluminium doors (any size) for smooth opening & closing of door including replacement of missing aluminium round shape or tubular handle, renewing rubber/ neoprin gasket, missing screws, aluminium strip for holding glass etc. Quantity on door basis of all sizes, any other required item to be brought & replaced but will be paid separately. EA 7 2658.62 18610.34 61 Repair & maintenance of aluminium windows for smooth opening & closing of window including replacement of defective hinges, missing aluminium handles, renewing rubber / neoprin gasket, missing screws etc. Quantity on window basis required for all sizes, any other required item to be brought & replaced but will be paid separately. EA 7 813.99 5697.95 62 Providing & Fixing / Renewing Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading). With float glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. M2 7.5 1403.19 10523.90 63 Providing & Fixing / Renewing Tuffened glass Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading) with tuffened glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. Brand:- Saint globin, Modi guard M2 5 1610.16 8050.78 64 Providing & fixing double action hydraulic floor spring of approved brand and manufacture cofirming to IS: 6315, for aluminium doors, including cost of cutting floors as required, embedding in floors and stainless steel cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. With stainless steel cover plate minimum 1.25 mm thickness complete as per direction of the EIC. EA 5 2632.38 13161.89 65 Providing & Fixing Neoprin/EPDM rubber gasket replacing for alluminium glazed doors & Windows (exiting rubber gasket) including racking out the old putty, removing glass and refixing the same properly. Brand:- RAMSON or equivalent M 300 110.17 33050.55 WATER SUPPLY PIPINGS 66 Providing and placing on terrace (at all floor levels) polyethylene Circular water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.complete including taking out old one and shifting in civil maint. Store. L 3000 10.25 30762.44 67 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15mm dia nominal bore M 22 300.31 6606.75 68 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore M 15 343.61 5154.11 69 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore M 15 436.03 6540.51 70 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore M 5 575.21 2876.05 71 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore M 5 710.47 3552.36 72 Making connection of G.I. distribution branch with G.I. main 25mm to 40mm nominal bore by providing and fixing tee including cutting and threading the end of pipe, necessary excavation & backfilling etc. complete. EA 5 850.07 4250.34 73 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. b) 20 mm outer dia. M 50 255.70 12785.05 74 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. c) 25 mm outer dia. M 40 331.30 13252.08 75 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. c) 40 mm outer dia. M 40 524.87 20994.90 SANITARY FITTINGS 76 Providing and fixing white vitreous china flat back/ovel wash basin of required colour with C.I. brackets, pair of 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including making all connections, cutting and making good the walls wherever required including taking out the old damaged one & depositing in the civil store if any. Wash basin of size 630x450 mm. EA 3 2469.24 7407.73 77 Providing and fixing white viterous china flat back or wall corner type lipped front urinal basin of standard/ existing size (430x260x350mm or 340x410x265 mm sizes respectively) and required colour with C.P. flush pipe, C.P. couplings, spreaders, unions, clamps and waste fittings including cutting and taking out the old damaged one to deposit in civil store if any. EA 3 1537.14 4611.43 78 Providing and fixing white vitreous china water closet squatting pan (Indian type) of required colour with 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) all fittings & fixtures required to connect with the cistern and including making good the walls & floors by C.C. 1:2:4 or C.M. 1:4 as required. Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store. Orrisa Pattern W.C. pan of 580 x 440 mm. EA 2 6308.54 12617.07 79 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow rrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store.: W.C. pan with ISI marked white solid plastic seat and lid. EA 2 7463.71 14927.42 80 Providing and fixing 10 litre capacity low level PVC flushing cistern of approved make and required colour with manually controlled device (handle lever) confirming to IS: 7231, with all fittings and fixtures complete including taking out the old damaged one if any, depositing in the civil store. EA 8 1109.92 8879.34 81 Providing & fixing complete kit including all fittings, syphon,washer etc. for low level PVC cistern of approved quality i/c taking out the old damaged/ broken one if any to deposit in civil store. EA 8 331.76 2654.07 82 Providing and fixing solid plastic seat with lid of approved quality, required size & colour for pedestal type W.C. pan with hinges rubber buffers etc. completed I/c taking out the old damaged one if any to depositing in the civil store. Solid Plastic seat with lid of requiered size & colour. EA 6 638.41 3830.48 83 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (Push/ Rotating type) 15mm nominal bore EA 15 535.36 8030.39 84 Providing and fixing C.P. brass long /Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore Brand:- Hindware / cera /jaquar EA 11 932.20 10254.15 85 Providing and fixing C.P. brass long nose bib cock/ Pillar cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore EA 8 765.05 6120.42 86 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge. EA 6 964.64 5787.81 87 Providing and fixing PVC Connection pipe of approved quality with unions & other fittings for Geaser or wash basin-45cm or required length including dismantling of old and damaged one for 15mm nominal bore. EA 25 91.12 2278.05 88 Providing and fixing semi rigid/flexible PVC waste pipe of approved quality with union, coupling & other necessary fittings for wash basins and sinks (upto 40mm dia.) including dismantling the old damaged one if any. EA 22 111.44 2451.77 89 Providing and fixing P.T.M.T. liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. EA 6 156.94 941.61 90 Providing and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. a) 15 mm to 25 mm dia EA 20 86.42 1728.48 91 Supply and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. b) 32 mm to 50 mm dia. EA 10 288.82 2888.22 92 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end), Nominal bore from 20 mm to 50 mm including removing the old and damaged one if any. Brand:- ZOLOTO/Leader/ Ruhe EA 13 661.01 8593.14 93 Providing and fixing Float/ ball valve set 15/20/25mm nominal bore of approved quality with rod etc. complete (High or low pressure with plastic floats) for over head water tanks complete including removing the damaged one if any. Brand:- SUPREME/RELISE EA 18 414.32 7457.82 94 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. (Item include Cost of Dismantaling, Removing and all labour, material required to complete removing and installation work.) EA 3 660.88 1982.64 95 Providing and fixing P.T.M.T. waste coupling for wash basin and sink of approved quality, colour and make. a) Waste coupling 31 mm / 38 mm dia. EA 10 110.79 1107.91 96 Providing and fixing 8 mm dia C.P. / S.S. Jet or hand health faucet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. EA 6 325.48 1952.86 97 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 75 mm dia M 15 109.51 1642.71 98 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 110 mm dia M 15 203.39 3050.79 99 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including fixing & painting of all fittings and brackets, cutting and making good the walls wherever required and return the old wash basin in civil store:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer EA 3 4461.21 13383.62 OTHERS MISCELLAEOUS ITEMS 100 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. EA 4 1498.92 5995.69 101 Providing & Fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated J or L hooks, bolts & nuts 8mm dia. G.I. plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confirm to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat. M2 10 1161.19 11611.89 102 WATER TANK CLEANING -Cleaning of over head water tanks below 5000 litre capacity. EA 25 350.23 8755.87 103 WATER TANK CLEANING of underground/ overhead water tanks above 5000 litre capacity L 40000 0.07 2610.15 104 Providing & Fixing G.I. Chainlink Fabric Fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-In-Charge. a)Made of G.I. wire of dia. 4 mm. M2 50 948.79 47439.40 105 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. sqm 20 974.75 19494.99 106 JOBS BASED ON (DSR - 2023): Estimated cost of DSR items is Rs.1,50,000/-. DSR-2023 at which contactor shall execute any work which is mentioned in DSR - 2023 as per requirement and need to keep GAIL premises maintained during the contract period. Any item covered under the DSR-2023 and as directed by EIC (Engineer-in-charge). Note : Payment for those items which are not available above in SOR shall be regulated as per DSR - 2023. It is further clerified that only those items of DSR - 2023 shall be operated which are not given above i.e. in any item of entire SOR of this contract. EA 150000 1.00 150000.00 107 Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). M2 3 5481.21 16443.64 108 Providing suction tanker of capacity 2000 litres for suction of sludge from the septic tank and dispose outside the Gail premises including required pipe length,driver, operator, diesel and labour reuired for operating the tanker. Trip 5 2966.08 14830.38 109 Trimming of leaves/branches from trees like neem just before autumn season as per the direction of SIC/EIC including labour , tools & tackels & disposing outside the Gail premises . The size of the cutting stem should not be greater than 25mm and as per instruction of EIC. Unit of measurement is EA i.e. trimming of each tree. Rate shall be quated for each tree. EA 50 46.61 2330.49 110 Providing and applying polyether based polyurethane (PU) waterproof coating consisting of two components (resin + hardener) in four coats consisting of a primer adhesion quote and three ceiling quotes applied by brush evenly to perfect level @ minimum 160 gram/square metre/coat over RCC slab including sprinkling the last coat of P.U. with a layer of clean sand 300 micron and laying minimum 50 mm thick PCC (1:2:4) over the fully cured coating in panels of Max 1.2 m X 1.2 m with 24 SWG chicken wire mesh finished smooth and sealing joints between panels with polysulphide sealant as per approved manufacturer specification and including preparing the base surface (levelling, cleaning, filling up cracks with thin paste of polyurethane filling compound) providing fillets of 75 mm radius with PCC (1:2:4) at junctions of horizontal and vertical surface continuing the waterproofing on the vertical face to a minimum height of 150 and an over finish roof surface terminating it in continuous groove of 10 mm×20 mm and filling with polyurethane sealent putty continue in the treatment into rainwater outlet by providing 450 mm× 450 mm at all outlets levelled down by minimum 25m finishing all complete.Cement supplied by the contractor at their cost M2 10 889.82 8898.23 111 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) 111.1 For fixed portion Powder coated aluminium (minimumthickness of powder coating 50 micron) kg 50 494.90 24745.12 111.2 For shutters of doors, windows & ventilators includingproviding and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittingsshall be paid for separately) kg 50 591.43 29571.56 112 Removal old & fixing of new Sun film including proper dispose of the removing material as per the instruction of EIC. Brand 3M or equivalent M2 10 508.47 5084.70 TOWNSHIP EARTH WORK 1 Earth work in excavation in foundations, trenches or drains (not exceeding 1.5 mtr in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, disposal of excavated earth, lead upto 50 m and lift upto 1.5 m disposed soil to be levelled and neatly dressed .a) all kinds of soil. M3 3 242.65 727.95 2 Filling of available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 mtr and lift upto 1.5 mtr. M3 2 182.71 365.42 3 Surface dressing of the ground i/c removing vegetation, grass and in equalities upto 15cm average depth and disposal of rubbish lead upto 50 m and lift upto 1.5 m. All kinds of soil M2 40 31.83 1273.38 4 Supplying and spreading of good earth at site i/c roylty and carriage upto 5km(earth measured in stacks will be reduced by 20% for payment) M3 5 796.60 3983.02 5 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1.2 M above ground level , wild bushes of any height and removal of rubbish upto a distance of 50 m outside the boundary wall as directed by EIC.NOTE If grass will cut only upto ground, dump 50 m away from boundarywall outside and only uprooting will not be done than only 60% of the measurement wil be paid. M2 3000 16.41 49219.90 SUPPLY OF MACHINERY 6 Supplying the JCB with driver, including fuel/diesel, helper & other consumables for JCB etc. as and when required. HR 8 1525.42 12203.39 7 Supply of tractor with trolly OR with cultivator OR leveller equipment/machinery & including driver, diesel & consumables required for performing day to day jobs, for 08 hours per day basis or prorata basis.labours will paid separately through the concerned item. DAY 6 1707.75 10246.50 8 Supplying Dewatering Pump set of capacity 7000 litres/hour with experienced operator for cleaning of sanitary inspection chambers & Septic tanks located at GAIL Premises, rate includes transportation of pump , operator, tools, tackles and fuel etc. HR 10 1073.35 10733.47 CONCRETE WORK 9 Providing & laying cement concrete in footings & bases for columns, kerbs, steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:3:6 (1 Cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) M3 6 6800.08 40800.50 10 Providing & laying cement concrete in footings & bases for columns, kerbs,steps, floors, roofs, paths, etc. for all floor levels, excluding the cost of centering and shuttering. Concrete of mix 1:2:4 (1 cement: 2 coarse sand : 4graded stone aggregate 20 mm nominal size). M3 4 7344.30 29377.19 11 Reinforced cement concrete work in walls (any thickness), including floors, roofs, attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : with 1:1.5:3 (1cement: 1.5 Coarse sand(Zone-3): 3 graded stone aggregate 20 mm nominal size.) M3 2 10117.07 20234.13 12 Centring and shuttering ic strutting and propping etc.and removal of form work in all types of cement concrete and R.C.C. work for all levels. M2 20 365.56 7311.21 13 Reinforcement for R.C.C., work including cutting bending, binding and placing in position complete for all levels. a)Thermo Mechanically Twisted bars Fe500D or more KG 100 100.54 10053.72 14 Dismantling cement concrete floor/Cement concrete pathway,bitumineous road, & R.C.C. etc. of any mix i/c stacking of serviceable material within 50 meters lead & disposal of rubbish to the dumping area away & outside the premises. M3 2 2269.20 4538.39 15 Providing and fixing upto floor five level precast cement concrete string or lacing coarses, copings, bed plates, anchor blocks, plain window sills, Shelves, Louvers, steps, Staircases, etc., including hoisting and setting in position with cement mortar 1:3 (1cement: 3 coarse sand) including the cost of required centring, shuttering 1:1.5:3 (1cement: 1.5 Coarse sand(Zone-3): 3 graded stone aggregate 20 mm nominal size.) M3 1 9419.92 9419.92 16 Supplying and stacking of graded stone aggregate 20 mm at site/ all the locations of work within the premises. M3 6 1802.63 10815.75 17 Supply & stacking of coarse sand (approved quality) at site/all the locations of work within the premises. M3 6 1834.25 11005.50 18 Supply & Stacking of Portland Cement (OPC-43 Grade) of apprvoed brand at site which shall be in the form of newly filled bags of 50 kg capacity. Item includes all the charges like cost of cement, transportation, loading, unloading & other overheads as applicable. KG 1000 6.78 6779.60 LABOUR SUPPY 19 Providing services of semi skilled nature of manpower like, mason/ carpenter/painter/plumber/ welder etc. on 08 hours per day basis with required tools & tackles. DAY 70 739.00 51730.00 20 Providing services of Unskilled nature of manpower on 08 hours per day basis with required tools & tackles. DAY 200 655.00 131000.00 BRICK WORK 21 Brick work with bricks of class designation 75 in foundations & plinth in 1:6 cement mortar(1 Cement : 6 Coarse Sand). M3 2.5 6648.65 16621.62 22 Brick work with bricks of class designation 75 in super structue for all floor levels in 1:6 cement mortar (1cement :6 coarse sand) M3 3.5 8488.52 29709.82 23 Half brick masonry in Cement mortar 1:4 (1 cement :4 coarse sand) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level. M2 3 1047.60 3142.80 24 Brick pitching by Flush / Ruled/ Struck or weathered pointing with cement mortar 1:3 (1cement: 3fine sand) half brick thick, including supply of bricks and preparing the surface complete With common burnt clay F.P.S. (non modular) bricks of class designation 7.5. M2 5 840.28 4201.40 FINSHING WORK 25 Providing cement plaster on the wall surface: 12 mm thick plaster in 1:6 CM (1 cement :6 coarse sand ) M2 35 320.35 11212.21 26 Providing cement plaster on the wall surface: 12 mm thick cement plaster of mix 1:4(1 cement : 4 coarse sand ). M2 12 333.12 3997.44 27 Repairs to the plaster in patches or replastering as per the existing thickness i/c cutting , dismantling old plaster or skirting , the patch in proper shape and raking out the joints , applying the cement slurry and plastering the surface of the wall complete for all floor levels i/c necessary scaffolding etc. and disposal of the rubbish to the dumping ground within 50 m lead with cement mortar 1:4 (1cement : 4 fine sand) M2 95 510.28 48476.94 28 Providing and applying plaster of paris including putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. M2 30 244.89 7346.63 29 Distempering with 1st quality acrylic distember (Ready mix)having VOC content less than 50 grams/ litre of approved brand and manufacturer and of stated shade and colour by SIC/EIC on old work to give an even shade ( Two or more coats) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. MAKE:(Asian paints- Tractor UNO or equivalnet). M2 2500 58.45 146121.57 30 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of stated shade and colour by SIC/EIC complete, as per manufacturers specification i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.Three or more coats on new work. MAKE:(Asian paints- Tractor UNO). M2 55 173.06 9518.41 31 Painting with synthetic enamel paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work ( two or more coats ) for wood/ steel work i/c necessary scrapping if any, for all shades. M2 130 95.83 12457.85 32 Painting with synthetic enamel paint of approved brand and manufacture and of required shade to give an even shade for wood/ steel work i/c necessary scrapping if any, for new work (Three or more coats) M2 20 210.91 4218.18 33 Finishing walls with Acrylic Smooth exterior paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade on old work (Two or more coats applied @ 0.90 ltr/ 10sqm). i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 250 112.56 28140.64 34 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Three or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete.MAKE:(Asian Paint-Apex or equivalent) M2 70 149.71 10479.74 35 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm ( Asian Royale or equilent) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 40 208.44 8337.55 36 Finishing walls with water proofing cement paint of approved brand and manufacture and of stated shade and colour by SIC/EIC to give an even shade on old work ( Two or more coats@ 2.20 KG/10 Sq.m) Complete i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 70 70.66 4946.23 37 Finishing walls with water proofing cement paint of approved brand and manufacture and of of stated shade and colour by SIC/EIC to give an even shade for new work (Three or more coats) i/c sand papering, scrapping , Repairing with putty/POP at desired places etc. complete. M2 10 108.97 1089.74 38 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even/ required shade on old work of any paint or distemper i/c sand papering, scrapping complete, of required shade ( Two or more coats) M2 40 88.98 3559.12 39 Painting with aluminium paint of approved brand and manufacture to give an even shade (one or more coats on old work). M2 20 89.49 1789.81 40 Relettering with black japan paint or with required shade of paint of approved brand and manufacturer. per letter per CM height 1200 3.59 4306.74 41 Lettering with black japan paint or with required shade of synthetic paint of approved brand and manufacturer. per letter per CM height 150 5.73 859.95 FLOORING 42 Grinding & polishing of terrazzo / kota /marble/granite etc. flooring with rubbing machine, hand grinder, 1st class mason & all required tools / tackles consumables (polish) etc. on 08 hours per day basis, complete as per direction of EIC. Payment shall be made on the basis of actual working hours on prorata basis. Day 10 1474.99 14749.90 43 Providing and fixing 1st quality ceramic glazed floor tiles/wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including spacer bar in between the tiles & grouting with pigment of matching shade/ as desired by EIC/SIC complete. including removing the broken tiles and raking out the old under layers and apply cement slurry complete. M2 10 1037.25 10372.53 44 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. M2 8 2862.82 22902.54 45 Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete .Size of Tile 60x60 cm 0.00 0.00 A Size of Tile 600x600 M2 15 1448.12 21721.77 B Size of Tile 800x800 M2 8 1757.65 14061.23 46 Supplying & Stacking of Red sand stone gang saw cut 30 mm thick (exposed face fine dressed with rough backing) as per direction of EIC. M2 10 662.86 6628.60 STEEL WORK 47 Provoding & Fixing pressed steel door frames of profile B confirming to IS:4351 manufactured from commercial mild steel sheet of 1.6mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle section 50x25 mm, or base ties of 1.6 mm pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. press butt hinges, 2.5mm thick with mortar guards, lock strike plate and shock absorbes as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by EIC. Fixing with adjustable lugs with split end tail to each jamb. M 20 543.75 10874.99 48 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) sections of any shape & size., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete at any height. Hot finished seamless type tubes. KG 50 192.36 9617.92 49 Steel work riveted, bolted or welded in built up sections / framed work of any shape and size including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer using structual steel etc as required in landings of stair case, gratings, shutters frame andsteel window, rolling shutter, collispal gates frames, gates including windowgrillsand similar works at any height (Angle, tea, flats, channels, MS pipes, plates etc.). KG 400 124.63 49853.79 DOOR & WINDOW FRAME & SHUTTER/ CUP BOARD SHUTTER ETC. 50 Supply and fixing G.I. wire mesh of approved quality. to windows & wooden frame/shutter using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm and necessary screwsnails including refixing of the existing beading and necessary painting if any. Item includes removal of defective wire mesh (only area of mesh to be measured). M2 15 1219.64 18294.56 51 Providing and fixing glazed shutters for doors, windows, clerestory windows using 4.00 mm thick glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. Item includes removal of defective shutters if any. IInd class teak wood 35 mm thick. M2 3 4605.23 13815.69 52 Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (over all area of the shutter to be measured) worn out shutter to be deposited in the civil store, after taking out. M2 6.5 2024.82 13161.33 53 Providing and fixing Sainless steel SS304 curtain rod having wall thickness of 1.20mm with two SS 304 brackets fixed with SS screws and PVC sleeves etc., wherever necessary complete : 20 mm dia M 50 236.56 11827.75 54 Providing and fixig bright finished brass 150 mm mortice latch and lock, ISI mark with six levers and a pair of anodised aluminium lever handles of approved quality with necessary screws etc complete i/c taking out the old damaged one if any. Brand :Harrison/PLUS POINT EA 15 932.20 13982.93 55 Providing and fixing aluminium die cast section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Brand : Hardwyn/ozone EA 5 1048.58 5242.90 56 Renewal of old putty of glass panes (length) M 10 52.34 523.43 57 Providing & fixing fly proof wire gauge to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire Gauge with 0.63 mm dia. Wire and 1.4mm aperture on both sides. M2 10 787.43 7874.25 ALUMINIUM WORK 58 Repair & maintenance of aluminium doors (any size) for smooth opening & closing of door including replacement of missing aluminium round shape or tubular handle, renewing rubber/ neoprin gasket, missing screws, aluminium strip for holding glass etc. Quantity on door basis of all sizes, any other required item to be brought & replaced but will be paid separately. EA 6 2658.62 15951.72 59 Repair & maintenance of aluminium windows for smooth opening & closing of window including replacement of defective hinges, missing aluminium handles, renewing rubber / neoprin gasket, missing screws etc. Quantity on window basis required for all sizes, any other required item to be brought & replaced but will be paid separately. EA 5 813.99 4069.96 60 Providing & Fixing / Renewing Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading). With float glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. M2 4 1403.19 5612.75 61 Providing & Fixing / Renewing Tuffened glass Glazing in aluminium doors, windows, ventilator shutters and partions etc. with EPDM rubber/ neoprene gasket and all other consumables etc. complete as per architectural requirement and the directions of engineer-in-charge (excluding the cost of aluminium snap beading) with tuffened glass panes of 5.50 mm thickness (weight not less than 13.50 kg/ sqm) including removal of broken glass panes and refixing old wooden fillets/ aluminium strips etc. Brand:- Saint globin, Modi guard M2 7.5 1610.16 12076.16 62 Providing & fixing double action hydraulic floor spring of approved brand and manufacture cofirming to IS: 6315, for aluminium doors, including cost of cutting floors as required, embedding in floors and stainless steel cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. With stainless steel cover plate minimum 1.25 mm thickness complete as per direction of the EIC. EA 6 2632.38 14358.43 63 Providing & Fixing Neoprin/EPDM rubber gasket replacing for alluminium glazed doors & Windows (exiting rubber gasket) including racking out the old putty, removing glass and refixing the same properly. Brand:- RAMSON M 40 110.17 4406.74 WATER SUPPLY PIPING 64 Providing and placing on terrace (at all floor levels) polyethylene Circular water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.complete including taking out old one and shifting in civil maint. Store. L 4000 10.25 41016.58 65 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 15mm dia nominal bore M 15 300.31 4504.60 66 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 20 mm dia nominal bore M 20 343.61 6872.14 67 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 25 mm dia nominal bore M 20 436.03 8720.68 68 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore M 5 575.21 2876.05 69 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore M 5 710.47 3552.36 70 Making connection of G.I. distribution branch with G.I. main 25mm to 40mm nominal bore by providing and fixing tee including cutting and threading the end of pipe, necessary excavation & backfilling etc. complete. EA 3 850.07 2550.21 71 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 20 mm outer dia. M 70 255.70 17899.08 72 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. b) 25 mm outer dia. M 40 331.30 13252.08 73 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. c) 40 mm outer dia. M 50 524.87 26243.62 74 Providing & fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all PVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. d) 50 mm outer dia. M 75 740.40 55529.69 SANITARY FITTINGS 75 Providing and fixing white vitreous china flat back/ovel wash basin of required colour with C.I. brackets, pair of 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including making all connections, cutting and making good the walls wherever required including taking out the old damaged one & depositing in the civil store if any. Wash basin of size 630x450 mm. EA 3 2469.24 7407.73 76 Providing and fixing white viterous china flat back or wall corner type lipped front urinal basin of standard/ existing size (430x260x350mm or 340x410x265 mm sizes respectively) and required colour with C.P. flush pipe, C.P. couplings, spreaders, unions, clamps and waste fittings including cutting and taking out the old damaged one to deposit in civil store if any. EA 2 1537.14 3074.29 77 Providing and fixing white vitreous china water closet squatting pan (Indian type) of required colour with 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) all fittings & fixtures required to connect with the cistern and including making good the walls & floors by C.C. 1:2:4 or C.M. 1:4 as required. Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store. Orrisa Pattern W.C. pan of 580 x 440 mm. EA 2 6308.54 12617.07 78 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow rrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required Item includes dismantling and taking out the old damaged one of any type, if any to deposit in the civil store.: W.C. pan with ISI marked white solid plastic seat and lid. EA 10 7463.71 74637.12 79 Providing and fixing 10 litre capacity low level PVC flushing cistern of approved make and required colour with manually controlled device (handle lever) confirming to IS: 7231, with all fittings and fixtures complete including taking out the old damaged one if any, depositing in the civil store. EA 12 1109.92 13319.02 80 Providing & fixing complete kit including all fittings, syphon,washer etc. for low level PVC cistern of approved quality i/c taking out the old damaged/ broken one if any to deposit in civil store. EA 20 331.76 6635.18 81 Providing and fixing solid plastic seat with lid of approved quality, required size & colour for pedestal type W.C. pan with hinges rubber buffers etc. completed I/c taking out the old damaged one if any to depositing in the civil store. Solid Plastic seat with lid of requiered size & colour. EA 6 638.41 3830.48 82 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (Push/ Rotating type) 15mm nominal bore EA 25 535.36 13383.99 83 Providing and fixing C.P. brass long /Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore Brand:- Hindware / cera /jaquar EA 25 932.20 23304.88 84 Providing and fixing C.P. brass long nose bib cock/ Pillar cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore EA 15 765.05 11475.79 85 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge. EA 6 964.64 5787.81 86 Providing and fixing PVC Connection pipe of approved quality with unions & other fittings for Geaser or wash basin-45cm or required length including dismantling of old and damaged one for 15mm nominal bore. EA 25 91.12 2278.05 87 Providing and fixing semi rigid/flexible PVC waste pipe of approved quality with union, coupling & other necessary fittings for wash basins and sinks (upto 40mm dia.) including dismantling the old damaged one if any. EA 20 111.44 2228.88 88 Providing and fixing P.T.M.T. liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. EA 6 156.94 941.61 89 Providing and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. a) 15 mm to 25 mm dia EA 20 86.42 1728.48 90 Supply and fixing of GI fittings for small repair works such that Tee, Elbow, Nipple, Socket, Union, Reducessor etc. complete with all required consumables. b) 32 mm to 50 mm dia. EA 10 288.82 2888.22 91 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end), Nominal bore from 20 mm to 50 mm including removing the old and damaged one if any. Brand:- ZOLOTO/Leader/ Ruhe EA 12 661.01 7932.13 92 Providing and fixing Float/ ball valve set 15/20/25mm nominal bore of approved quality with rod etc. complete (High or low pressure with plastic floats) for over head water tanks complete including removing the damaged one if any. EA 24 414.32 9943.76 93 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. (Item include Cost of Dismantaling, Removing and all labour, material required to complete removing and installation work.) EA 3 660.88 1982.64 94 Providing and fixing P.T.M.T. waste coupling for wash basin and sink of approved quality, colour and make. a) Waste coupling 31 mm / 38 mm dia. EA 10 110.79 1107.91 95 Providing and fixing 8 mm dia C.P. / S.S. Jet or hand health faucet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. EA 6 325.48 1952.86 96 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 75 mm dia M 15 109.51 1642.71 97 Providing & fixing UPVC pipes, having working pressure 4 kg / cm 2 supply including all PVC plain fittings. This includes jointing of pipes & fittings with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of EIC. External work. a) 110 mm dia M 15 203.39 3050.79 98 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including fixing & painting of all fittings and brackets, cutting and making good the walls wherever required and return the old wash basin in civil store:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer EA 3 4461.21 13383.62 OTHERS MISCELLAEOUS ITEMS 99 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. EA 4 1498.92 5995.69 100 Providing & Fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated J or L hooks, bolts & nuts 8mm dia. G.I. plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confirm to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat. M2 10 1161.19 11611.89 101 WATER TANK CLEANING -Cleaning of over head water tanks below 5000 litre capacity. EA 25 350.23 7959.89 102 WATER TANK CLEANING of underground/ overhead water tanks above 5000 litre capacity L 40000 0.07 2372.86 103 Providing & Fixing G.I. Chainlink Fabric Fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-In-Charge. a)Made of G.I. wire of dia. 4 mm. M2 25 948.79 23719.70 104 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. sqm 50 974.75 48737.49 105 JOBS BASED ON (DSR - 2023): Estimated cost of DSR items is Rs.1,00,000/-. DSR-2023 at which contactor shall execute any work which is mentioned in DSR - 2023 as per requirement and need to keep GAIL premises maintained during the contract period. Any item covered under the DSR-2023 and as directed by EIC (Engineer-in-charge). Note : Payment for those items which are not available above in SOR shall be regulated as per DSR - 2023. It is further clerified that only those items of DSR - 2023 shall be operated which are not given above i.e. in any item of entire SOR of this contract. EA 100000 1.00 100000.00 106 Providing suction tanker of capacity 2000 litres or above for suction of sludge from the septic tank and dispose outside the Gail premises including required pipe length,driver, suction pump, suction pump operator, diesel and labour reuired for operating the tanker. EA 7 2966.08 20762.53 107 Trimming of leaves/branches from trees like neem etc just before autumn season as per the direction of SIC/EIC including labour , tools & tackels & disposing outside the Gail premises . The size of the cutting stem should not be greater than 25mm and as per instruction of EIC. Unit of measurement is EA i.e. trimming of each tree. Rate shall be quated for each tree. EA 25 42.37 1059.31 .... more in document
