Tender For Remodeling Of Hss Budhal.- 1 Rendering of service for Complete Site plan, Architectural drawings, structural Design drawings, other drawings needed at site for the Remodelling of HSS Budhal (G+1)as per latest Indian standard codes including required soil testing and vetting of structural drawings from govt. approved institutes IIT/NIT/DIQC. (as per the directions ofPWD(R&B) deptt.) (The contractor shall supply 5(five) sets of hard copy and 1 (one) set of soft copy of each drawings. 3 (three) sets of drawings shall be supplied in A1 size and 2(two) sets in A3 size. All Drawing shall be prepared on CAD. 2 Dismantling of Old Building 3 Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:In cement mortar. 4 Demolishing cement concrete manually/bymechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge; 1:3:6 or richer mix (i/c equivalent design mix). Building 5 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead :Of area of 3 sqm. and below. 6 Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead 7 Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of :G.S. Sheet. 8 Dismantling aluminum / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge: 9 Disposal of Malba upto lead of 2km by M.T 10 Building Part 11 Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. 12 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 13 Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) Crushed . 14 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with.1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size 15 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 16 Stone filling hand packedin horizontal level including cost of stones 17 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement-All work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) 18 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) 19 Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level 20 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 21 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.All works upto plinth level in 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) crushed. Using 20% boulder. 22 Reinforcement for RCC work including straightening cutting, bending, placing in position & binding all complete with TMT bars. 23 Centring and Shuttering including strutting, propping etc and removal of form work for 24 Foundations: footings, bases of columns etc. for mass concrete. 25 Lintels, beams, plinth beams, girders, bressumers and centilevers. 26 Columns, Pillars, Piers, Abutments, Posts and Struts. 27 Suspended floors, roofs, landings, balconies and access platform. 28 Edges of slabs and breaks in floors and walls 29 Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand) . 30 Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete 31 Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand) & Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) 32 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile BFixing with adjustable lugs with split end tail to each jamb 33 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete fixed to steel windows by welding. 34 6 mm Cement plaster to ceiling of mix 1 : 3 ( 1 cement : 3 fine sand) 35 12mm cement plaster of mix 1:6 (1 cement : 6 fine sand) 36 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including lSI marked M.S. pressed Butt hinges bright finished of required size with necessary screws excluding panelling which will be paid for separately,all complete as per direction of engineer- in charge). 35mm Thick Second class Kail wood. 37 Providing and fixing panelling or panelling and glazing inpanelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Particle Board 12mm thick Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS: 3087 marked 38 Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/sqm (4mm thick) float glass panes including lSI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 30mm thick second class Kail wood 39 Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average width for aperture 1.4 mm in both directoin with wire of dia. 0.63 mm for doors, windows and clerestory windows with hinges and necessary screwslSI marked M.S. pressed bright finished butt hinges with necessary screws of required size. 30 mm thick Second class kail wood. 40 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 4 mm thick glass pane (weighing not less than 10 kg/sqm) 41 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angles 40x40x6mm for diagonal braces 42 Providing and fixing lSI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 250x16 mm 43 Providing and fixing lSI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 44 150x10 mm 45 100x10mm 46 Providing and fixing lSI marked oxidised M.S. handles conforming to IS : 4992 with necessary screws etc.complete: 47 125 mm 48 100 mm 49 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 60x60cm 50 Providing and fixing 1st quality ceramic glazed floor tiles conformingtoIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 51 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 52 Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in Charge. 16.90.1 18 mm thick 53 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete. 54 Distempering with 1st quality acrylic washable distemper (ready made) of approved manufacturer and of required shade/ colour complete as per manufacturers specifications Two or more coats on new work 55 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) 56 Applying priming coat:With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 57 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work 58 Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. Crushed 59 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete (welded) 60 Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.5 mm thick with zinc coating not less than 350 gram/m2 61 Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.0.50 mm thick with zinc coating not less than 275 gram/m2. 62 Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) : 63 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position :Budloo / Fir wood 64 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge. 65 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 66 Carriage of material from source to site of work by mechanical transport including loading /unloading and stacking complete. 67 Sand for an average distance of 175 kms by MT 68 Stone aggregate below 40mm for an average distance of 20 kms by MT 69 Stone aggregate below 20mm for an average distance of 20 kms by MT 70 Bricks for an average distance of 175 kms by MT 71 Stone for an average distance of 5kms by MT 72 Disposal of Excavated material for an average distance of 1km by MT 73 Electrical Part 74 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 75 Wiring for light/ power plug 2x4 sq. mm FRLS PVC insulated conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 nO 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 76 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit. 77 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 78 4x4 sq.mm +2x4 sq. mm earth wire 79 supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making the good the same in case of recessed conduit as required 25 mm 80 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. 81 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. 82 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 83 5/6 amps switch 84 3 pin 5/6 amp socket outlet 85 6 pin 15/16 amp socket outlet 86 Indicator 5/6 Amp 87 Blank plate 88 Two module stepped type electronic fan Regulator. 89 Supplying and drawing 1 x 1.5 sqmm FRLS PVC insulated copper conductor single core cable in the existing surface/recess PVC conduit for invertor wiring as required. 1x1.5 SQMM INVERTOR WIRING 90 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board,415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc as required (But without MCB/isolator. 6/8 way (4+18) Double Door 91 Supplying and fixing 5 A to 32 A rating, 240/415 Volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 92 Single Pole 93 SPN 94 Single Pole Blanking Plate 95 suppplying and fixing of angle/Batten Holder (metal ring) polycarbonate including making complete connections etc. as required along with providing and fixing of 15 watt LED Bulbs. 96 supplying and fixing of 4 feet long LED Batten light 20 Watt. 97 Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz including connections etc. as required. 98 Ceiling fan 1200 mm sweep (3 star Rating Crompton high speed,Havells velocity, orient PSPO or equivalent) 99 Supplying, installation, Testing & commissioning of inverter 2000VA along with 2 nos. long tubular batteries 150AH and trolly of suitable size. 100 SITC of 16 sqmm PVC copper Cable for service line.
