Tender For To Carry Out The Remaining Works Of Pune Municipal Corporation Jaysingrao Sasane Park On B.T. Kavade Road.-ITEM NO : 1 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m.) By Manual Means ( SSR Item No : 21.01 ) (PMC Bhavan ) Unique No (15201) Rate List Year (2024-2025) ITEM NO : 2 Transportation of material obtained from excavation including soil, Cu.M rubble, bricks, RCC concrete, kerb stones, steel railing, iron pipes, channels etc. Obtained from excavation, dismantling, loading in a Truck of minimum 5 Cu M capacity or designed capacity and transporting within the municipal limits or any designated place, unloading, stacking or spreading of material etc. complete. As directed by Engineer In charge ( SSR Item No : 78.36 ) (PMC Bhavan ) Unique No (17223) Rate List Year (2024-2025) ITEM NO : 3 Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material ( SSR Item No : 3.01 ) (PMC ROAD ) Item Spec : (MORTH 401) Unique No (116) Rate List Year (2023-2024) ITEM NO : 4 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. ( SSR Item No : 21.38 ) (PMC Bhavan ) Unique No (15233) Rate List Year (2024-2025) ITEM NO : 5 Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) ( SSR Item No : 24.04 ) (PMC Bhavan ) Unique No (15309) Rate List Year (2024-2025) ITEM NO : 6 Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) ( SSR Item No : 25.13 ) (PMC Bhavan ) Unique No (15318) Rate List Year (2024-2025) ITEM NO : 7 Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) ( SSR Item No : 25.72 ) (PMC Bhavan ) Unique No (15333) Rate List Year (2024-2025) ITEM NO : 8 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. ( SSR Item No : 26.33 ) (PMC Bhavan ) Unique No (15352) Rate List Year (2024-2025) ITEM NO : 9 Providing first class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in plinth including bailing out water manually, striking joints on unexposed faces, pointing with cement mortar 1:3 on exposed face and watering etc. Complete. ( SSR Item No : 27.02 ) (PMC Bhavan ) Unique No (15371) Rate List Year (2024-2025) ITEM NO : 10 Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. ( SSR Item No : 32.11 ) (PMC Bhavan ) Unique No (15444) Rate List Year (2024-2025) ITEM NO : 11 Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item Number 15 to 18 prior approval of Superintending Engineer will be necessary ( SSR Item No : 35.26 ) (PMC Bhavan ) Unique No (15576) Rate List Year (2024-2025) ITEM NO : 12 Building (Bd-V : Water supply and sanitory fittings)Upvc sanitary pipes all 50 mm dia. ( SSR Item No : 49.V-357 ) (PMC Bhavan ) Unique No (18028) Rate List Year (2024-2025) ITEM NO : 13 Providing & Applying One Coat Oil Primer & Two Coats Of Oil Painting of selected in multi color shades for existing Kid’s Toy like Slide, Swing, Sea Saw etc. ( SSR Item No : 18 ) (PMC Garden ) Unique No (19518) Rate List Year (2024-2025) ITEM NO : 14 Air Walker DIMENSIONS :- 1060mm (Length) x 810mm (Width) x 1600mm(Height). SAFE AREA: - 2.0 M x 1.8 M Air Walker Equipment made from “B” class G.I. Pipe of different NB. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bend at the radius of 250mm. The bottom support of M.S. round plate of Ø250 mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm are made up from bright material. A24 circlips are used for assembly. The bearings used are “6205” permanent lubricated sealed bearing of repute brand likw SKF, FAG. High tensile steel galvanized nuts & bolts are used for assembly. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To build structure bushes are used which are made from M.S.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. Bolt M8 X 16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, , transport, etc complete all. Work done should be as per engineer incharge ( SSR Item No : 10 ) (PMC Garden ) Unique No (19631) Rate List Year (2024-2025 ITEM NO : 15 SHOULDER BUILDER Providing and fixing Shoulder Builder made from “B” Class G.I. pipe. The Center Pipe is of 100mm NB made from “C” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The handle movement frame is of 25 NB & 20 NB made from “C” Class G.I. pipe. To Join the centre pipe & handle movement frame seamless pipe of 130mm dia & 3mm thickness is used. The foundation used for fixing consists of three equal items i.e. 100mm NB made from “C” class G.I. Pipe, M.S. Round Plate of 250 mm dia & 10mm thickness & 25 mm X 25mm X 3mm M.S. angle. Closing caps made from top quality FRP material which is of 2 mm thickness. The pins used are made up of 25 mm dia bright bar. The bearing used are of “6201” & “6205” permanent lubricated sealed bearing of reputed make like SKF, FAG. The nut bolts used for assembly are made from S.S. material. The serclips used for assembly is of 25 mm diameter. The Poly Urethin plastic bush is used for handling. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3 m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, , transport, etc complete all. Work done should be as per engineer incharge ( SSR Item No : 1 ) (PMC Garden ) Unique No (19622) Rate List Year (2024-2025 ITEM NO : 16 Single Chest Press DIMENSIONS:- 9000mm (L) x 650mm (W) x 2150mm. (H). SAFEAREA :- 2.0 M X 1.7 M. Chestpress equipment madeup of“B”ClassG.I.pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100NBmadeup of“B”Class G.I. pipe. The bottom welded with supportof M.S.round plate of Ø250mm &10mm thickness.The connecting pipes are made up from 25NB “B”class G.I.pipe. The handle frame is made up from 25NB & 32NB “B”class G.I.pipe. To build structure bushes are used which are made from MS.seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush isused. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm&10mmthick. Main pipe supported with 25mm X 25mm M.S. angles of 2mm thickness and 20mm x 40mm MS square pipes of 2mm thickness. Foundation cover Closing Cap is madefrom HDPE / LLDPE Material.The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mmX 300mm X 2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of high quality HDPE / LLDPE material. Pins used of Diameter 25mm and 17mm are made up from bright material. The bearings used are of “6205zz” & “6203zz” permanent lubricated sealed bearing of reputed brand like SKF, FAG. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24mm & A16mm. The foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, , transport, etc complete all. Work done should be as per engineer incharge ( SSR Item No : 11 ) (PMC Garden ) Unique No (19632) Rate List Year (2024-2025) ITEM NO : 17 Leg Press Providing and fixing Leg Press made from “B” Class G.I. pipe. The center pipe is of 100mm NB made from “C” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter & 10mm thickness is welded at bottom. The remaining outer frame is of 40mm NB made from “C” class G.I. pipe. The foundation used for fixing is consist of three equal items i.e. 80mm NB made from “C” class G.I. pipe, M.S. Round plate of 250mm dia & 10mm thickness, 25 mm X 25 mm X 3mm M.S.angle. To join the centre pipe & outer frame seamless pipe of 130 mm dia & 3mm thickness is used. The seats are fitted on the outer frame is made up of FRP material of size 330 mm X 330 mm of thickness 3 mm & M.S. Plate of thickness 5mm and Size 250 mm X 200 mm is used to support it. The footrests is made from FRP/C.I./Aluminum casting material, its sizes are 130 mm X 300 mm & 5 mm thickness. The frame of footrests consists of 25 NB made from “C” class G.I. pipe. Closing caps made from top quality FRP material which is of 2 mm thickness. The inner bushes are made from seamless pipe, its diameter is60mm& 8mm thickness. The pins used in are made up of 25 mm diameter hardened bright bar. The bearings used are of “6205” permanent lubricated sealed bearing of reputed make like SKF, FAG. The handles used are of Rubber grip. The Nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50 mm diameter. The serclip used for assembly are of 25mmdiameter. foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.3m below ground level and painting is done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface is applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Rate inclusive of labour, material, , transport, etc complete all. Work done should be as per engineer incharge. ( SSR Item No : 7 ) (PMC Garden ) Unique No (19628) Rate List Year (2024-2025) 2 48804 / Number 97608 ITEM NO : 18 DOUBLE POST SWING (Proving and Fixing) Rec. Age :- 4-14 yrs. The area :- 3.5 x 1.0m Safe play area :- 4. X 2.0m The leg supports of the single post swing is made up of 150 NB while the top bar is of 50 NB GI pipes. The GI pipes are powder coated. All pipes are ‘A’ class pipes, The two swings are made up of 10mm thick skid reinforced. The seats of the single support swing are made up of 10 mm thk rubber with anti skid. The rubber seat is suspended on 6mm thk gi chain. The ball bearings of brands like SKF, FAQ are mounted inside a specially designed nylon clamp. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per Engineer incharge Instructions ( SSR Item No : 3 ) (PMC Garden ) Unique No (19526) Rate List Year (2024-2025) ITEM NO : 19 WAVE SLIDE 2.1 MT (Proving and Fixing) (FRP)/ROTO MOLDING ( LLDPE /HDPE) Rec. Age :- 4 – 12 yrs. The area :- 4.8 m x 0.5 m Safe play area :- 5.8 m x 1.5 m Height :- 2.1m The wave slide chute is made up of 4 mm thick fiber reinforced plastic materials. The structure comprises of 20 NB and 25 NB powder coated GI pipe. The center support is made in 80 NB powder coated GI pipe. The ladder cum railing is made 20 NB and 25 NB GI pipes. The platform is made up of 14 SWG GI sheet with anti skid for firm foot grip. There are triangular steps 16 SWG GI sheet. The chute has its end such as it causes safe landing of the child. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per Engineer incharge Instructions. ( SSR Item No : 10 ) (PMC Garden ) Unique No (19533) Rate List Year (2024-2025) ITEM NO : 20 ROTO WAVE SLIDE – 2.1 m (Proving and Fixing) Age Group :- 4 – 12 yrs. Product Area :- 5.5 m x 1.0 m Safe Play Area :- 6.5 m x 2.0 m Material Specification: The ROTO Wave Slide is made up of Low Linear Density Poly Ethylene by Rotational molding process in one piece having shell thickness of 4-5 mm with UV stabilized. The slide is supported on a center support of 80 NB GI pipe. The landing supports of the slide are supported by two 20 NB pipes. The slide ladder is made up of 25 NB GI pipe & the ladder hand-railing is made up of 15 NB and 20 NB pipes respectively. The triangular steps of the ladder are made up of 16 SWG GI sheets. The ROTO wave slide platform is made up of 14SWG GI sheet. The trade and riser of the ladder are designed in such a way it won’t entrap child’s foot while playing. All the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it. This slide is designed as per ASTM & EN standards which are globally accepted standards. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per Engineer incharge Instructions. ( SSR Item No : 12 ) (PMC Garden ) Unique No (19535) Rate List Year (2024-2025) ITEM NO : 21 ANIMAL MGR (Proving and Fixing) Rec. Age : - 3 - 12 yrs. The area :- 1.5 m dia. Safe play area :- 2.5 m dia. The main frame the animal merry go round is made up of 25 NB & 40 NB pipes. The GI pipes are powder coated. The stand is made in NB GI pipes. The whole structure is mounted on heavy-duty bearing shaft permanently lubricated with water sealant. The animal seats are made out of molded plastic in rotational molding process (LLDPE/HDPE). It accommodates 4 children at a time. All pipes are ‘B’ class pipes All Structures are to be Powder Coated. All Work Done As Per General Raw Material Sheet Added Below. Work done should be as per Engineer incharge Instructions. SSR Item No : 18 ) (PMC Garden ) Unique No (19541) Rate List Year (2024-2025) ITEM NO : 22 STANDARD SEE-SAW – (Proving and Fixing) Age Group : - yrs. Product Area : - 2.5 m x 0.3 m Safe Play Area : - 3.5 m 1.3 m The seats of the see-saw are made from ROTO molded plastic. The lever is made up of 15, 20, 25 NB GI pipes and fitted on 40 NB GI pipe. The bearing used is of heavy duty bush type. All pipes are ‘B’ class pipes The Foundation pipes are embedded in C.C. stock of size 0.45 x 0.45 x 0.45m and painting done by attractive color spraying after proper surface treatment, Shot blasting and initial coat of yellow primer surface applied before top coat. The top coat is done using the best quality brand paint or duly powder coated of minimum 60 micron thickness. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment etc all. Work done should per Engineer incharge Instructions. SSR Item No : 21 ) (PMC Garden ) Unique No (19544) Rate List Year (2024-2025) ITEM NO : 23 Stamped Concrete :- Thin overlay approximately 1/32 to 5/ thicker application may be nessecery in some situations) stamped concrete overlays over M-20 concrete of 100 mm thicksurface, interior, applied smooth,textured or stamped in various patterns and designs using stamps and seamless texture skins, then antiqued, chemically stained or integrally colored and sealed with the appropriate coating. Systems sealers or protective top coats according to the job conditions and specifications. including the cost of M-20 concrete of 100 mm thickness) SSR Item No : 1.10 ) (PMC ROAD ) Unique No (204) Rate List Year (2023-2024) ITEM NO : 24 type Kerb: Providing & fixing Reinforced precast-L shape kerb stone Using 6 mm steel bars 4 number along the kerb length and mm steel bar 500 mm c/c vertical reinforcement , M-30 grade concrete with dimensions 350 mm high,125 mm thick with built base of 187 mm x 75 mm, including 2 numbers of 50 mm dia sleeves for services at the top of the base & with top external edge with rounding of 20 mm radius in highly superior quality surface & edge finish in 1 meter length & Painting as per direction Engineer - in - Charge. ( Including excavation for kerbing, lead lift and transportation of excavated material, P.C.C. below kerbing) SSR Item No : 1.01 ) (PMC ROAD ) Unique No (195) Rate List Year (2023-2024) ITEM NO : 25 Providing and erecting chain link fencing 1.6 M. height with G. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/ with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete. SSR Item No : 46.39 ) (PMC Bhavan ) Unique No (16044) Rate List Year (2024-2025) ITEM NO : 26 Building (Bd-W : Water supply and sanitory fittings)Concentina Coil Wire SSR Item No : 49.W-09 ) (PMC Bhavan ) Unique No (18065) Rate List Year (2024-2025) ITEM NO : 27 Wall Painting art work : painting artistic work on any type surface and at any height using scaffolding with skilled artists per the instructions of site incharge.measurement will be as per actual max.size of art.rate for background apex paint and lettring will be paid seperately SSR Item No : 63.4 ) (PMC Bhavan ) Unique No (16694) Rate List Year (2024-2025)
