|
| 1 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10kA breaking capacity (B/ C/D tripping characteristic as per type of road and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947- 2, low watt losses, trip free mechanisum , energy limiting of class 3as per IEC, minimum phase termination capacity of 35sq.mm. ,conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab typetest reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR Single pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating |
| 2 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4-Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %,round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cabletray(with cable tie) including testing etc. as required of following size. OEM musthave it\"s own in house NABL accrediated Laboratory for testing procedure as perIS:10810.For additional technical parameters of product / work refer Annexure\"A\" attached with this BSR. 4 core |
| 3 | Providing & laying Chequered terrazzo tiles of approved make 22mm thick with marble chips of size upto 6mm, in floors, jointed with neat cement slurry mixed wit pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28mm thick bed of C.M. 1:4 :Light shade using shade cement. |
| 4 | M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). |
| 5 | oviding & Fixing of IK10 IP65 protected 600 mm height LED Bollard Luminarie with base plate made ofpowder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminousefficacy ≥ 90 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integralelectronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS Rnumber constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency >85%, PF>0.9, THD<20% and input Voltage range of 90-270V AC at 50Hz. System life of 30000 Burninghours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as perengineers choice. driver current <750mA. Fixture must be in compliance with BIS Standards and Trademark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessoriesfrom OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technicalparameters of products/ work , refer Annexure \"A\" attached with this BSR .Minimum lumen output 800 lm Bollard |
| 6 | Dismantling of Cement Concrete Pavements as per MoRTH Specification Clause 202.Dismantlingofcementconcretepavementsbymechanicalmeansusingpneumatictoolsbreakingtopiecesnotexceeding0.02cuminvolumeandstockpilingatdesignatedlocationsanddisposalofdismantledmaterialsuptoaleadof1000m,stackingserviceableandunserviceablematerialsseparately |
| 7 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge). |
| 8 | labour charges for Excavating trenches of required width for pipes dressing ofsides, ramming of bottoms, depth up to 1.5 Mtr. including taking out theexcavated soil, and then returning the soil as required in layers not exceeding20cm in depth including consolidating each deposited layer by ramming,watering etc. and disposal of surplus excavated soil as directed within a lead of50 Mtr.:All kind of Soils |
| 9 | Rough Chisel dressed Sandstone 35 mm thick flooring of approved shade setover 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointingwith cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects :Pinksand stone (Bansi Paharpur stone) |
| 10 | Supplying & preparing and laying of track carpet on track: - (a)bymixingof screendblackcottonsoil andcynder (semiBurncoal)60%+ 40% respectively 50mm thick layer, 2 layers including screening, watering, laying, rollingbyhand roller compactionetc. insingle layer. Total thickness2 layers of mixture 100mm, laying should be 50mm - 50mm each layer. (b)bymixingof screendBlackcottonsoil andcynder (semi burncoal)50%+ 50%repctily25mmthick includingscreening,watering, laying, rollingbyhand roller compaction etc. in single layer. (c) screened cynder (semiburn coal)on track in 1 mm thick layer. Completework (inabove a,b,c) should bedone as per direction andentire satisfaction of Engineer incharge. |
| 11 | Reparing and fixing of statue I love bhiwadi in central park with required dismentling and new fixing |
