Tender For Construction Of Wuas Buildings Under Jurisdiction Of Executive Engineer, Anopgarh Branch Water Resources Division-Ii Gharsana - Sub Division Rawla (Package-447B)
Tender Value
95 Lakhs
Estimated cost
Bid Submission
29 Oct 2025
0 days left
EMD
1.90 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anupgarh → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Wuas Buildings Under Jurisdiction Of Executive Engineer, Anopgarh Branch Water Resources Division-Ii Gharsana - Sub Division Rawla (Package-447B)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 2 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth levelM10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 3 | Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricksCement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 5 | Providing and laying damp-proof course with cement concrete grade M-15 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification50 mm thick |
| 6 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 7 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 8 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills,chhajjas,lintel,beam, plinth beam etc. |
| 9 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix |
| 10 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (\"Original producers\" who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) |
| 11 | Precast terrazo tiles of approved make, 20mm thick with marble chips of size upto 6mm laid in floors, and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete on 20mm thick bed of cement sand mortar 1 : 4. Dark shade using ordinary cement. |
| 12 | Precastterrazzotilesofapprovedmake20mmthickwith marble chips of size upto 6mm in skirting & risers, treads of steps and dados 12mm thick cement plaster 1:3 (1 cement : 3 coarse sand) jointedwithneat cement slurrymixed with pigmenttomatchtheshadeofthetiles,includingrubbing andpolishingcompletewithtilesofDarkshadeusing ordinary cement. |
| 13 | Providing and fixing M.S. sheet 1mm thick single leaf door shutterinangleironframe35x35x5mmsuitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, asperdirectionofEngg.inchargebutexcludingcostof chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 14 | Provideandfixingexternalgradeboardsolidcoresingle leafflushdoorshuttersISI2202-67markedusingphenol formaldehyderesiningluebothsideswithapprovedsteel fitting complete as per annexure \"A\"25mm thickcommercial veneer both side |
| 15 | Providing, hoisting and fixing up to floor five level precast cementconcreteJali1:2:4(1cement:2coarsesand:4 graded stone aggregate 6mm nominal size) reinforced with1.6 mm dia Mild steel wire including centring and shuttering,rougheningcleaning,fixingandfinishingin cement mortar 1 : 3 (1 cement : 3 fine sand ) etc complete as per approved design excluding plastering of jambs, sills and soffits40 mm thick |
| 16 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish12mm thick. |
| 17 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete.40mmthickwith20mmthicknominalsizeaggregate. |
| 18 | Plasteronnewsurfaceonwallincementsandmortar1:3 including racking of joints etc. complete fine finish :20mm thick |
| 19 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shadeTwo or more coats on new work |
| 20 | White washing with lime to give an even shade including all scaffolding:New work (three or more coat) |
| 21 | Colour washing of all shades to give an even shade including all scaffolding: |
| 22 | Paintingtopofroofwithbitumenofapprovedqualityat 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10sqm including cleanin the slab surface with brushesandfinallywithapieceofclothlightlysoakedin kerosene oil complete; With residual type petroleum bitumen of penetration 80/100 |
| 23 | Kota stone slab 20 mm to 25 mm thick (semi-polished) |
| 24 | ConstructionofSoakagewellinalltypesofsoilof approveddrawing,top90Cm.Portionin450mmthick masonrywithCM1:6,80mmthickstoneslabcovering, jointingofslabinCM1:3,Ralthal,kharanja40mmthick M-15 grade C.C flooring, earth work etc . complete includingdisposalofsurplusearthwithinaleadof50 mtr .Inner dia60 Cm & 10 to 12 Mtr deep. |
| 25 | P.&FSquattingPan(Indiantype)whiteglazedvitreous china 1st quality W.C. Pan (IS : 2556 Mark) with 100 mm vitreouschinaPorStrapincludingcuttingandmaking good the wall and floor (excluding the pair of foot rest.)Size 450mm |
| 26 | Vitreous china foot rests 250x130x30 mm |
| 27 | P&FWVCWashbasin(IstqualityIS:2556Mark)of approved make with C.I. brackets duly painted 1 No. 15 mmC.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste couplingofapprovedmake,P.V.CWastepipewithPVC nut 32 mm complete including cutting & making good the wall :Size 450 mm x 300 mm |
| 28 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 approvedquality/makeincludingjoiningthepipewith solvent cement rubber ring and lubricant. 110 mm dia |
| 29 | P&FrigidPVCpipefittings(IS:4985mark)ofapproved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 110mm dia |
| 30 | Coupler (Socket)110 mm |
| 31 | Plain Tee 110 mm |
| 32 | Bend 87.5 110mm |
| 33 | Vent Cowel 110 mm |
| 34 | P-Trap |
| 35 | P & F Gun-metal Non-return Valve or Check Valve (IS : 778Make)ofapprovedmake,superiorquality:15mm nominal bore.Vertical |
| 36 | P& FStopCock (IS:8931Mark), superiorquality& of approved make:Brass 400 gm. 15mm nominal bore. |
| 37 | P& FStopCock (IS:8931Mark), superiorquality& of approved make:Brass1350gm. 25 mm nominal bore. |
| 38 | P&FBibCock(IS:8931Mark),Superiorqualityof approved make:Brass 400 gm,15mm nominal bore. |
| 39 | P&FPVCStorageTankISIMarked(IS:12701) indicatingtheBISlicenseNo),ofapprovedmakewith cover,25mmdia1MlongG.I.over-flowpipe&25Cm. longwashoutpipewithplug&socket,includingmaking connectionetc.,completeofapproveddesign:500litres capacity |
| 40 | Providing and fixing Polyethylene - Aluminium - Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450:2004U.V.stablisedwithcarbonblackhaving thermal stabillity for hot and cold water supply, capable to withstand temperature upto 80ºC including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplersconnectorsetc.withclampsat1.00metre spacing.This include the cost of cutting chases and includingtestingofjointscompleteasperdirectionof Engineer In chargeConcealed installation including cutting chases and making good the walls etc. complete.2025 (25mm OD) pipe |
| 41 | Providing and fixing Polyethylene - Aluminium - Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450:2004U.V.stablisedwithcarbonblackhaving thermal stabillity for hot and cold water supply, capable to withstand temperature upto 80ºC including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplersconnectorsetc.withclampsat1.00metre spacing.This include the cost of cutting chases and includingtestingofjointscompleteasperdirectionof Engineer In chargeConcealed installation including cutting chases and making good the walls etc. complete.3240 (40mm OD) pipe |
| 42 | P & F Flush Cock / Flush Valve (IS : 9758 Mark)forWC ofapproved quality makeBrass / Gun metal Half-turn wt. 1 Kg. of approved quality / make,25mmnominalbore. |
| 43 | Constructionofchamberinalltypeofsoilwith300mm thickmasonryinCM1:6m,10cmthickC.C.1:5:10in foundation, 20mm thick insider plaster in Cm 1:6, finished withfloatingneatcement,50mmthickM-15gradeC.C. flooring,earthworketc.completeasperdesignincluding disposal of surplus earth within a lead of 50 mtr.Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. |
| 44 | SITC of ContactorOEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chartandmadeoutfrom1.6mmthickpowdercoated CRCA sheet, enclosure comprising of over load protection relay,shortcircuit&singlephasingprotection,Illuminated ON/OFF pushbuttons, ammeter,voltmeter,indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work,.For single phase Submersible / Monoblockpump0.5 HP to 1.5 HP (DOL starter) |
| 45 | 120cmhighfencingwithangleironposts50x50x6mm placed at every 3 meters apart 30 cm . in ground embedded in cement concrete 1:3:6 (30x30x45cm)corner &everytenthposttobestruttedwith50x50x6mmangle iron provided with four horizontal line and two diagonals of blackbarbedwirebetweentwopostfittedandfixedwithG.I. staple including earth work in exacavation etc. complete.Add or deduct for 3 wires line over basic item |
| 46 | Providingandfixingsteelgate,grating,andgrillmadeof angles,tees,squarebars,flats,orblackpipewith holdfastandfittingscompleteasperdesignanddrawing includingcuttingweldingandfabricationwithprimingcoat of red-oxideExtra if square , rectangular hollow tubelar section are used or grill made by flats only |
| 47 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"sISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work. |
| 48 | Short point (up to 3 mtr.) |
| 49 | Medium point (up to 6 mtr.) |
| 50 | S&F following sizesof ISI marked ( IS:14927 P - II ) virgin materialUPVC trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewith screws, expansionfastenersas required. For additional technical parameters of product / work. 25 mm x 12 mm |
| 51 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm., conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work.Double pole MCB(With B/C curve tripping Characteristics) 6 A to 32 A rating |
| 52 | P & F ISI marked (IS :3854) 16 amp. flush type non modular switch CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work. |
| 53 | Providing & Fixing of ISI marked (IS:1258) batten/angle lampholder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work . |
| 54 | Providing & Fixing of 3/6 pin 16 amp flush type non modular socket made out from Industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. |
| 55 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work.570mm (+/-10%) batten with min. lumen output 1000 lm |
| 56 | Providing&Fixingof ofM.S.J-hookofstandarddesign madeoutof16mmdia.M.S.roundbarandfixedwith cement concrete mortar with required support as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work. |
| 57 | Providing & Fixing of 1200 mm sweep BLDC technology power saving ceiling fan which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not lessthen0.9 ,servicevalue(CMM/W)minimun6.85, air deliveryminimun220CMM,speedminimum330RPM (toleranceasperIS:3742019)THDlessthen10% and completewithdownrodof15mmdia.ERW(Electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe up to 80 cm, cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work.Without Remote. |
| 58 | Providing&FixingofofISOcertifiedcompanymade Multiple socket with surge and spikes protection cartridge notlessthen5KVasperPWDspecificationforelectrical Works with minimum four nos. universal 6 A sockets, one 6 Aswitchand3pincompanyfittedplugtopand3core multistrand copper lead minimum 1.5 mtr. including making connection etc as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work. |
| 59 | Providing & Fixing of modular type 120 W Step Fan regulatordulyISImarked(IS11037:1984)withCM/Lno. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws& silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work .5 step fan regulator 2 Module 360 dgree rotating. |
| 60 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withelectrolytic grade Copper made of copper rodsconfirming to IS 613-1964, of purity >99.7 %,Inner / outer sheath confirming to IS:5831 inexistingRCC/Hume/Stoneware/PVCpipe/open duct/cabletrench/Cabletray(withcabletie)including testingetc.asrequiredoffollowingsize.OEMmusthave it\"sownin houseNABLaccrediatedLaboratory for testing procedureasperIS:10810Foradditionaltechnical parameters of product / work.1.5 Sq. mm.2 core . |
| 61 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressurediecastaluminummaterialwithheatdissipationfinson housing with UV stabilized PC (UV stablization report submitted for UV cover)/ToughenedGlasscover andsecondarylensoneachLED& shouldbeSMDtypeof 3to 5watt each .TheSystemefficacy >=125 lm/ wtand potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency>85% ,THD(I)<10% Humidity10% to90%RHWorkingTemp-5Cto 45C .driver current <750mA. The luminaire shall be BIS certified and Trademarkcertified.LifeExpectancy Equalormorethan50000 burninghrswithMinimum70%lumenmaintened,CRI>70andCCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KVexternalinsidedrivercompartment.drivershouldbePhaseto phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossingondiecasthousingtoallow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in houseNABL lab setup for all testingfacilitiesfor LEDfixtures. (LM79/LM80)Certificate/report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work.LED Street Light fixture with Minimum lumen output 5600 lm. |
AI Tender Summary
Tender Timeline
Oct 09, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 30, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender