Providing And Installing Open Gym And Play-Ing Equipments Along With Other Allied Works At Yenak And Takali Village Under Csr Head Of Mungoli Sub Area.-Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 2 Earth work in excavationby mechanicalmeans (Hydraulic xcavator) /manual means over areas (exceeding 30 cmin depth, 1 .5 min width as well as 10 sqm onplan) including getting out and disposal of excavated earthleadupto 50 m andlift tlpto 1.5 in, as directedby Engineer-in-charge. All kinds of soil. 3 Supplying and filling in plinth with sandunder floors, including watering, ramming, consolidating and dressing complete. 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources). 5 Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M - 30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand,filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. 6 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 7 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand). 8 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm 9 Engraving letters in hard stone 10 Providing and fixing spiral slide of dimension 10ft x 2ft x 5ft with Slide length 20ft slide height 8ft, Slide Material: FRP of thickness 6 to 8mm 11 Providing and fixing double swing 2 seat of 8ft x 4ft x 8ft with frame of Mild steel and seating area made up of FRP material 12 Providing and fixing 4 seater see saw With Mild steel frame and high durability and tolerate capacity of 150 kgs on each side 13 Providing and fixing 8 seater platform M. G. R. of 5ft x 5ft x 3ft with Outer frame 32 mm OD MS pipe, Handle 25 mm OD MS pipe, Center Pipe 2inch MS pipe 14 Providing and fixingRCC Garden bench with capacity of 3 person ,RCC bench with load carrying capacity of 400 kg., finishing etc complete andas per the direction of Engineer-in-charge. 15 Providing and fixing Air Walker with min dimension (1070 mm x 460 mm x 1360 mm) with specification mentioned below:-Main Post: 114 mm GÍ pipeOther Pipes: 88nmThickness :- 4.5mmMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded witlh joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shal! be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. As per instrcutions by engineer incharge or his representative. 16 Providing and fixing Shoulder Press Double with min dimension (2000 mm x 700 mm x 2200 mm) with specification mentioned below:-Main Post: 114 mm GI Pipe Other Pipes: 33mmMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI/ LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bolts withbase plate cover. As per instrcutions by engineer incharge or his representative. 17 Providing and fixing Chest Press Double with min dimension (2000 mm x 700 mm x 2200 mm) with specification mentioned below:-Main Post: 114 mm GI Pipe Other Pipes: 33mmMaterial : Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI/ LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bolts withbase plate cover. As per instrcutions by engineer incharge or his representative. 18 Providing and fixing Parallel bar with min dimension (1340 mm x 830 mm x 1240 mm) with specification mentioned below:-Main Post: 114 mm GI PipeOther Pipes: 33nmMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI/ LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bots with base plate cover. As per instrcutions by engineer incharge or his representative. 19 Providing and fixing Cross Walker with min dimension (1440 mm x 749 mm x 1145 mm) with specification mentioned below:-Main Post: 114 mm GI Pipe Other Pipes: 60mmMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI/ LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. As per instrcutions by engineer incharge or his representative. 20 Providing and fixing Horizontal Bar with min dimension (1490 mm x 1880 mm x 715 mm) with specification mentioned below:-Main Post: 114 mm GI PipeOther Pipes: 60 mmMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GI/ LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bots with base plate cover. As per instrcutions by engineer incharge or his representative. 21 Providing and fixing Triple Twister with min dimension (1340 mm x 1200 mm x 1240 mm) with specification mentioned below:-Main Post: 114 mm GI PipeOther Pipes: 33mm diaMaterial: Galvanized Carbon steel pipe and powder coated 80-100 micron thick using Akzo Nobel or equivalent. All welding joints of pipe shall be MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. All open ends of pipe to be closed with GV LLDPE caps, base plate cover made of virgin LLDPE plastic by rotational molding High quality grip rubber should be used on handles. Foothold shall be made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings should be used in the equipment. The equipment shall be fitted with in-built limiters. The equipment shall be fixed on ground with concrete and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. As per instrcutions by engineer incharge or his representative. 22 Total impact of GST for the purpose of CTC
