Tender For Construction Of Offer Md Accommodation At Island Ground Offers Enclave Chennai; 1 Lumpsum price worked out by the tenderer for BUILDINGS AND STRUCTURES as listed in Schedule ‘A’ Part-I 2 Lumpsum price worked out by the tenderer for SITE CLEARANCE/ AREA DEVELOPMENT as listed in Schedule ‘A’ Part-II 3 Lumpsum price worked out by the tenderer for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-III 4 Lumpsum price worked out by the tenderer for INTERNAL ELECTRICSUPPLY & PVC CONDUIT as listed in Schedule ‘A’ Part-IV 5 Lumpsum price worked out by the tenderer forROAD/ PATH/ HARDSTANDING /CULVERTas listed in Schedule ‘A’ Part-V 6 Lumpsum price worked out by the tenderer for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI 7 Lumpsum price worked out by the tenderer for AREA DRAINAGE as listed in Schedule ‘A’ Part-VII 8 Lumpsum price worked out by the tenderer for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-VIII 9 Lumpsum price worked out by the tenderer forEXTERNAL ELECTRIC SUPPLY as listed inSchedule ‘A’ Part-IX 10 Lumpsum price worked out by the tenderer forLIGHTNING PROTECTIONas listed in Schedule ‘A’ Part-X 11 Lumpsum price worked out by the tenderer for FIRE FIGHTING/ FIRE ALARM AND DETECTION as listed in Schedule ‘A’ Part-XI 12 Lumpsum price worked out by the tenderer for LIFT as listed in Schedule ‘A’ Part-XII 13 SCHEDULE A PART XIII (MISCELLANEOUS ITEMS)Note: This schedule is not pre-priced by MES 14 INTERNAL WATER SUPPLY 15 S&F for 15mm dia bore 2 way bib tap/cock fancy type, cast copper alloy chromium plated, with crutch or butterfly handle one way suitable for fixing health faucet and other for bip tap, screwed for iorn pipe or ferrule complete all as specified and directed. 16 S&F for 15mm dia bore, brass CP mixer valve 2 in 1 hot and cold water including connected with shower rose, screwed for iorn pipe or ferrule, complete all as specified and directed. 17 INTERNAL ELECTRIC SUPPLY /PVC CONDUIT 18 M&L for Point wiring complete with 1.5 sq mm single core PVC insulated FRLS unsheathed cable 1100 volts grade with multi stranded copper conductor confirming to IS-694 1990 wih ISI marked (for phase, neutral and earth) in and including stove enamelled Steel conduit with ISI Mark of minimum 20mm dia and all conduit accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed glvanised steel pressed terminal boxes alongwith suitable size modular cover plates with frames for fixing modular switches and sockets, fan regulators etc. of suiable size modules and the earth wire to be connected to common earth dolly complete all as specified and directed for the following :- Note: Location of light points, 6 Amp socket points and light fittings may be decided by Engr-in-charge as per site/user requirment 19 One light point controlled by one modular switch 6A one way 20 One Ceiling/Exhaust fan point controlled by one modular switch 6A 21 One 3 pin socket out let6 Amps on independent board 22 One 3 pin socket out let 6 A on same board 23 One light point controlled by two 2-way switch 24 One bell/buzzer point controlled by one bell push 25 M&L for Point wiring complete all a specified with 1100 Volts grade 4 sq mm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS 694 1990 with ISI marked (for phase, neutral and earth)in and includingstove enamelled Steel conduit ISI Mark of minimum size 20mm dia all accessories concealed including cutting/ chases in wall/ceiling/fixed to roof/truss/columns etc and including factory made branded make embossed galvanised steel pressed terminal boxes for fixing modular sockets of suitable sizemodules and the earth wire to be connected to common earty dolly all as specified and as directed.all as specified and as directed for One three pin modular switch socket 16 amps outlet on independent board 26 S&F modular bell switch suitable type AC 240V, 6 Amps complete all as specified and directed by Engineer-in-charge. 27 Supply and Fix Modular switches suitable for type AC 240V ,6 amps 1 Module 2 way complete all as specified and directed by Engineer-in-charge. 28 Supply and Fix call bell of multi music type AC 230 volts completeall as specified and directed by Engineer-in-charge. 29 Supply and Fix wall mounted fan of double string, steel body AC single phase, 230v of size 400mm sweep with, blades frame, louvers, oscillation control knob, tilting control white colour (body and blades) complete all as specified and directed 30 Supply and Fix decorative wall light fitiing made up of polycarbonate suitable for 9 Watts Retrofit LED LampB22 Base complete all as specified and directed 31 S&F reading light (Bed Side) wall mounting5/7 W Cool day light CCT of 3000K 400Lumen output complete all as specified and directed make PhilipsCat No 31437 or equivalent in Havells or Wipro 32 ROAD/PATH /HARDSTANDING/ CULVERT 33 M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines,edge lines ,stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. 34 EXTERNAL WATER SUPPLY 35 Supply ,install , test and commission of Centrifugal electrically driven self priming monoblock pump set with cast iron impeller capable of pumping 350 LPM at 36 Mtr head, squirrel cage TEFC induction motor3 phase, 415V AC,50 Hz suitable for delivery 350 LPM at 36 Mtr head coupled on common base chanel including necessary PCC foundation works, nuts and bolts, copper cable from starter to motor through PVC rigid pipe ,suitable size of suction pipe not less than 20 feet or as reqd at site, Air release valve complete all as directed and specified 36 Supply and Fix Foot Valve normax type including fixingas per IS4038 all as specified and directed 65 mm DiaMake :Kirloskar,Zoloto,L&T 37 Supply, install, test and commission LT feeder piller box/ Panel board IEC -614391 , CPRI approved,indoor type IP-43 , vermin proof, dust proof , fabricated with 2 mm CRCA sheet mounted on 40x40x4mm MS angle, 3 phase 4 wire , 440 volts , AC , 50hz with TPN aluminiumbusbar of capacity100 amps with pvc insulator heat shrink colour code sleeves , mounted on procelin insulators duly prewiredcomplete volt and amp meter , selector switch with all accessories and consists of the following switch gears :-(a) Bus bar chamber with electrolytic aluminium bus bar 100 Amp capacity for 3 phase - 01 set(b) MCCB 4 pole adjustable thermal/magnetic setting ,63A, 415 V ,25 KA- 01 Nos (c) MCCB 4 pole ,32A, 415 V ,10 KA- 02 Nos (Lift & Fire Pumps)(d) MCBTP ,32A, 415 V ,10 KA- 02 Nos (Pump Sets)(f) Supply and fixing DOL starter suitable for pumping set- 02 Nos 5 HP(g) MCB SPN 6-32 Amp 10 KA -01 Nos(Pump House)(h) Digital voltmeter, Ammeter,LED phase indicator lamp, selectror switch(i) Single phase preventer- 02 Nos (j) MCB SP 32 Amps 16 KA- 1 No, Street Light Timer digital type-01 No. 38 M&L for construction of valve chamber 450x450x450 mm depth with PCC foundation in the ration 1:4:8 brick work cement mortar in the ratio 1:6 using of class B bricks , PCC coaping at the top of the ratio 1:3:6 , plastering 15 mm thick in the ratio 1:4 including MSsheet cover 3mm thick with angle iron frame 50x50x6mm locking arrengement complete with painting on steel surface with one coat of red oxide paint over two coats of synthetic enameeled paint all as specified and directed . (Earthwork shall be measured and paid seperetely in the respective items) 39 Supply and Fix Stainer Y type made of cast iron body flanged type completely fixed to line including all necessary bolts Nuts washers Etc of size 50 mm Dia Make :Kirloskar,Zoloto,L&T 40 Supply only chlorine test kitof reputed Make for testing water chlorine with all fittments and OT solution complete 41 Supply only synthetic rubber insulatedmat 2 mm thickfor voltage upto3.3 KV as per IS 15652-2006 of Size 1 meter x 2 meter x 19 mm 42 Supply testing and installation of Bleaching Dozer Bucket Type capacity 145 Litres FRP type with all fittings and fioxtures Orifice plate Drain Valve,solution dozing line (PVC) dose cantrol Valve ,Water inlet valve, air Valve any other accessories or pipe line of size upto 25 mm are included in the quoted rates all as specified and directed and supplyCHLORINE TEST KIT 43 EXTERNAL ELECTRIC SUPPLY 44 Earthing with galvanised steel earth plate electrode 60 cm x 60 cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 metre below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level connected to main earth lead GI wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part I 1991, GI earth lead protected by GI pipe 15 mm dia light grade, providing and connected to earth test point with & including necessary excavation & earth works in any type of soil, returning filling, disposal of surplus soil to 50 metre, filing with mixture of charcoal and common salt up to 15 cm above top edge of earth plate, pit of PCC 1:2:4 with precast cover of RCC 1:2:4, watering arrangement with GI funnel, 20 mm dia GI light grade watering pipe, earth test point terminal block, commissioning & testing complete. ( Note :Main earth lead beyond 7.5 metre measured and paid for separately.) 45 M/L for LT cable route indicators Oval Shaped 200x150x6 mm cast Iron precastwith engraving LT MES CABLE embedded with PCC in mix 1:3:6 type C1 incl necessary exc, returning filling & removal of soil complete as directed. 46 .Supply and fix FRP pole box of size 168X253x115mm ,thermoplastic,polycabonate,IP-66 complete with 4 pole 32 A connector, Double compression glands-2 Nos, MCB SP 6 Amps mounted with GI clamps of suitable size with nuts and bolts on street light pole all as specified 47 Material and labour for street light bracket made of 40mm GI pipe light grade 1.5 m length bent in shape for mounting street light on one end, fixing the bracket on pole with suitable GI clamps, Nus and bolts all as specified and as directed.. 48 Fabricate, supply , install, test and commission LT feeder pilar box/panle board, outdoor type, fabricated with 3.15mm CRCA sheet mounted on 50x50x6mm MS angle, 3 phase 4 wire, 440v, AC, 50 Hz, with TPN aluminium bus bar of capacity 400 Amps with pvc heat shrink colour code sleeves, mounted on porcelin insulators complete volt and amp meter , selectro switch with all accessories and consist of the following switch gear: -( Main LTpanelatPGEPT & TA ) (i) Aluminium bus bar 3 phase & neutral of capacity 300 Amps(ii) MCCB 4 Pole 200 Amps 36 KA-01 No ( Incoming) (iii) MCCB 4 Pole 160 Amps 25 KA-02 No(iv) LED phase indication lamp for 3 phase-01 No 49 Fabricate, supply , install, test and commission LT feeder pilar box/panle board, outdoor type, fabricate with 3.15mm CRCA sheet mounted on 50x50x6mm MS angle, 3 phase 4 wire, 440v, AC, 50 Hz, with TPN aluminium bus bar of capacity 400 Amps with pvc heat shrink colour code sleeves, mounted on porcelin insulators complete volt and amp meter , selectro switch with all accessories and consist of the following switch gear: -( Main LTpanel at Tower 1 ) (i) Aluminium bus bar 3 phase & neutral of capacity 300 Amps(ii) MCCB 4 Pole 160 Amps 36 KA-01 No ( Incoming) (iii) MCCB 4 Pole 100 Amps 25 KA-05 No (FF,SF,TF,FF& Pump House) (iv) MCCB 4 Pole32 Amps 16 KA- 2 No ( Ground Floor & Spare)(ix) LED phase indication lamp for 3 phase-01 No 50 Supply only synthetic rubber insulatedmat 2mm thickfor voltage upto 3.3 KV asper IS 15652-2006 of Size 1 meter x 2 meter x 19 mm 51 Provision of trenchless bore using mechanical pneumatic drilling equipment for passing electric cables through HDPE pipe of 100mm dia under the existing bituminous/WBM road/PCC hard standings, depth range not less than 1.0 mtr and upto 1.5mtr and making good to the distrubed surfaces of road to match with its existing specifications all as specified and directed by engr-in-charge at site. Note : 1. Quoted rates deems to be inclusing of necessary earth work, transportation charges of Drilling machine, and cost of HDPE pipe and passing pipe through bore complete.2. Any damage to MES/Civil assets caused during trenchless bore shall be recitfied by the contractor at his own cost.Note:The rates are inclusive for obtaining necessary permission from state/Highway authorities and any other clearances as required before starting the work 52 FIRE FIGHTING SYSTEM/ FIRE ALARAM AND DETECTION 53 Supply, installation, testing, and commissioning of Fully automatic Star Delta Starter starter, suitable for the booster pump, complete with contactors, push button, LED type indicators, auto/manual selector switch, overload protection, current sensing type single phase preventer complete with all accessories and wiring etc.with ncomplete all as specified and directed 54 M & L for fire survival cable of size 3 core 16 sq mm with strandedannaealed bare copper conductor, mica tape wrapped for heat resistance up to 950deg centigrade, GI strip wire armouredand zero halaogen outersheathed XLPE insulation cable all as directed. Make: Havells/ KEI/ RR Kabel 55 M & L for PN 1.6 rated 100 mm NB polypropelene vortex inhibitor suction lift, conforming to BS 4504 with stainless wire mesh, bolts, nuts and washers, etc. complete all as specified and directed 56 M & L for PN 1.6 rated 100 mm NB CI Y -type strainer for suction conforming to IS 907: 1984 & (Reaffirmed 2020) with SS filter screen and flange drilling standard end connection conforming to IS 1538: 2018 and necessary accessories for suction side of fire pumps complete all as specified and directed.(at pump suciton header). 57 M & L for earthing complete with galvanized steel earth plate electrode of 60 cm X 60 cm X 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized strip of size 32 mm X 6 mm as earth lead by means of bolts, nuts, checknuts and washers of galvanized iron or steel, galvanized iron pipe of 40 mm diameter connected to earthing test point, all as shown in electrical plate No. 5, connected to earthing test point including testing on completion, excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep with a 10 mm deep CI cover hinged to CI frame on ground level, GI watering pipe, funnel, etc. complete all as specified and directed by the engineer-in-charge 58 M & L for Two wire addressable speaker with LED light flash/Beacon suitable for targeted announcements and equipped with a LED light flash ( to cater to hearing-impaired occupants). The unit shall be equipped with an LED that blinks in normal conditions and glows steadily upon activation. Both the control panel and speaker unit shall continuously scan for healthiness and cable connectivity to ensure integrity compliance. the speaker must have a minimum capacity of 5 watts with max voice current of 100mA. It shall have ABS housing along with Back box. it shall be able to produce 90 dB sound at 1 Mtr distance 59 M & L for remote repeater panel similar to main control panel capable of full supervision of all inputs an network integrity, having colour touch screen display, environmental adjustment control to maximise LCD legibility, LED status indicator. ( For power supply and OFF normal conditions) 60 M & L for low smoke zero halogen(LSOH) flame retardant fire alarm cable 2C x 1.5 Sqmm conforming to BS-7629-1, BS-6387 and BS EN 50200 and rated for 500V drawn through and including concealed PVC conduit and accessories of min 20mm dia NB and having plain annealed stranded copper conductor with primary insulation of glass mica fire resistant tape and secondary insulation of high performance silicon rubber, earth/drain wire of annealed tinned copper, electrostatic screen of aluminium fire barrier and type LTS3 outer sheathed conforming to BS 7655, suitable for operating temp -30 deg centigrade to +70 deg centigrade and min bending radius being six time the overall cable diameter, red in colour, including laying termination and ferruling complete all as specified and as directed 61 M&L for Firemans switch and Interconnecting with LV Switch The cost of any balance item to make MOEFA system installed under Sch A part XI above is deemed to be included in the quoted rates so as to make the system complete and fully functional ass per the prevailing engineering. 62 Supply and fixingof Mechanical foam type fire extinguishers, 9 Ltr capacity, IS:15683 : 2006, complete. 63 Supply and fixingof Dry powder ABCstoredpressuresqueezegriptypefire extinguishers, 9 kg capacity, IS:15683 : 2006, filled with ABC Mono AmmoniumPhosphatebasepowder-90completewithdischarge hose and wall mounting bracket, 2mm Mild Steel, EPDM Rubbers, Pressure Guage, which work effectively on allclass of fires (A, B, C & Electrical fires)complete. 64 Supply & fixing of 4 Nos of 9 lts capacityround bottom sand /water buckets along with round bottom type , enamel painted white inside and red outside& letter fire in black outside & handle with mounting bracket along with suitable MS stand to install the buckets as per the local fire standards 65 LIFT 66 Earthing with galvanised steel earth plate electrode 60 cm x 60 cm x3.15 mm thick, buried directly in ground (earth pit not less than 2.25 metre below normal ground level) with top edge of earth plate not less than 1.5 metre below normal ground level connected to main earth lead Copper strip 20 mmx3mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 of MES Schedule Part I 1991, GI earth lead protected by GI pipe 40 mm dia light grade, providing and connected to earth test point with & including necessary excavation & earth works in any type of soil, returning filling, disposal of surplus soil to 50 metre, filing with mixture of charcoal and common salt upto 15 cm above top edge of earth plate, pit of PCC 1:2:4 with precast cover of RCC 1:2:4, watering arrangement with GI funnel, 20 mm dia GI light grade watering pipe, earth test point terminal block, commissioning & testing complete. Note :Main earth lead beyond 7.5 metre measured and paid for separately.) 67 ELECTRIC CHIMNEY 68 Supply Install Testing and comissioning of Electric Chimney of size, Filterless Wall Mounted type,Operating Voltage 220 Volts 50 Hz with ,Auto Clean 3 speed cantrol gesture with 2X 1,5 LED and all other necessary fittingsand fixtures required complete all as specified and directed.Supply, erection & testing of electricalchimney with the following specificationsSize: 90 cmShape / mounting: Box / wall mountingSuction capacity : 1500-1800 cum/hrAir outlet size: 150 mmDuct size : 150 mm Duct :MOC- Stainless Steel,Duct pipe/baffle filter: inclusive as required.Motor type: BLDC motor, 240W.Blower type: MetallicLamp: 2 x 1.5 WFinish: Stainless SteelFeatures: Low Noise (less than 62 dB) steam auto cleanControls: Dual touch, multi speed option, motion sensor”.Make: Faber/ Hindware/Glen /Kaff/Cropmton 69 DG SET 70 Supply, installation, testing and commissioning of 40 KVA / 32 KW,(The capacity of Generator set shall be net after all due derating factors as per relevant lSI standard), silent Diesel engine Generating Set, 415 volts, 3 phase, 0.8 Power factor, 50 Hz, 4 wire system as per IS 10001/10002 comprising of40 KVA or equivalent, developing 1500 RPM, Water Cooled, electric start coupled toEquivalentalternator as per IS 13364 mounted on a common base frame with standard control panel for automatic starting on main control panel having meters,with emission control device as per CPCB IV + Norms and updated till date on procurement and CPCB approved acoustic enclosure suitable for ambient condition atChennai with integral fuel tank with battery and leads and accessories complete including required PCC foundation as per manufacturers instruction and confirming to conditions as per IS provisions:- 71 (A) Alternator :- Standard design alternator rated at 40 KVA net output at site after considering derating as per site conditions at 0.8 (lag) power factor AC, 3 - phase 4 - wire 415 volts 50 Hz, 1500 RPM, self excited self regulated screen protected drip proof IP 23 enclosure brushless design with winding in pole faces, insulating class H and voltage regulation of ± 1 % at rated voltage from no load to full load. The alternator shall be confirming to BS 2613/5000 and shall be imposition to generate supply with frequency regulation with in ± 1% tolerance. The alternator will be suitable for tropical climate and shall generally confirm to BS/IS – 4722 and as per the following provisions:- Make:- KIRLOSKAR/JYOTI / STAMFORD/CATERPILLAR(a) Insulation class - H(b) Temperature rise Class - H(c) Excitation: Self Excited(d) Regulation performance: The voltage is kept constant with ± 1 %, manual voltage adjustment within ± 5%(e) Frequency regulation ± 1 %(f) 2 runs of UG cable of suitable size from Alternator to AMP is deemed to be include in quoted rate. 72 (B) Diesel Engine: - Adequate capacity Diesel engine suitable for 40 KVA coupled drive independently above alternator and after considering derating as per site conditions after generating and reducing power consumed by accessories, directly coupled through flexible coupling, multi cylinder multi stroke direct injection, cold starting 1500 RPM, as per relevant ISI/BS - 5514 with an overload capacity of 10% for one hour in 12 hours continuous running complete with standard accessories all asspecified and required for safe handling and operation salient features of accessories shall be as under Make :- KIRLOSKAR/CUMMINS / CATERPILLAR (GEMCO) 73 (a) Fly wheel with housing (b) Cooling system :- Mounted radiator with fan & belts.(c) Cooling pump: - Centrifugal type belt driven. (d) Exhaust System :- Exhaust System complete with exhaust piping of suitable dia as per manufacture standard with MS pipe light grade up to and away two meters height from top of enclosure including necessary angle iron frame supports from floor to the bottom of exhaust pipe from the enclosure covered with mineral wool of thickness 50mm rapped with chicken wire mesh of size 2.25mm and aluminum sheet of 24 SWG to be complete with in the enclosure for safe exhaust without transforming vibration to the wall of the enclosure. Exhaust gas turbo charger type Exhaust manifold Silencer: Residential type Belows 74 (C) Fuel System :- Fuel injection system with fuel injectors, fuel injectionsolenoid switch/nozzles/ governor mechanical type capable for 1 % speed/frequency regulation.(i) Fuel filters(ii) Fuel hoses(iii) Lub oil System :-(iv)Lubricating oil filter(v) Lubricating oil pump(vi) Air Intake System :-(a) Air intake Manifold(b) Air cleaner dry type(a) Starting System :- Electric Self starter with maintenance free batteries including battery charging alternator.(b) Batteries:- 1 No. Maintenance free Battery of suitable AH capacity complete with copper conductor multistranded leads of suitable length from self starter to the battery terminals complete with initial charge and initial fill of electrolite all as specified.Make:- EXIDE / AMRON / Produced by original DG set manufacturers 75 (i) Starter gear ring(ii) Start and stop push button(iii) Ignition key / Switch(iv) Handling and operation: Salient features of accessories shall be asunder:(a) Radiator with blower fan(b) Corrosion inhibitor coolant(c) Paper element filters for fuel, lub oil and by pass.(d) Governor controlled direct fuel injection system(e) Fly wheel housing and fly wheel. 76 (D) Generator Monitoring Panel: Comprising of following:-(a) Microprocessor based integrator generator set monitories, metering,protection and control system with built torque matched volts/H3 over load control.(b) Engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown)(c) Alternator protection parameters like under voltage, over current, under frequency, over frequency ( alarm & shut down)(d) Relay drivers for remote annunciations(e) Cyclic cranking(f) Auto/manual start stop(g) Alternator trim adjustment from the front key pad(h) Operates within a temperature range 0- 50°C and humidity up to 95%(J) Remote monitoring capability through separate interface modulesk) Genset metering parameters like lube oil pressure, coolant temperature, engine speed(rpm), run hours, DC voltage, 3 phase volts and 3 phase amperes, frequency, KW, KVA, power factor 77 (l) Safety Controls : - Engine low lube oil pressure, high water temperature and over speeding of engine.(m) Coupling arrangement : - Flexible coupling, fly wheel to suit flexible coupling fly wheel housing.(n) Accessories :-A VM Pads built or separately mounted to manufacturer base frames.(o) Base Frame: - Made out of ISMC 200 of sturdy design made of MS channel with necessary reinforcement and predetermined holes. (p) Fuel Tank :- Daily service fuel tank of capacity minimum 08 hrs running storage (Inbuilt) made out of 3mm thick (Heat Retardant) sheet top and bottom with calibrated level indicating arrangement, stop cock, drain plug, fuel pump of suitable capacity and connected pipe line should be installed with in built inside the acoustic enclosure is inclusive of the cost of DG Set and is as per manufacturer design.(q) Deliverables:- Confirms the norms established by CPCB. 78 (E) AMF PANEL:-(a) Auto Main Failure (AMF) panel made out of 2 mm thick CRCA sheet, powder coated of conforming to IS 8623 totally enclosed dust and vermin proof with front and rear openings of 415 Volts, 3 Phase,4 Wire, AC 50 Hz having aluminum bus bar capacity required to carry current at 100% load of 40 KVA DG set with three phase and half neutral color coded, prewired with copper flexible cable, be all as specified with the following accessories, control cable from Gen set to AMF panel: (i) 63 Amps, 4 pole contactor - 2 Nos.(ii) MCCB, 4 Pole 63 Amps, 25 KA-2 Nos for both supplies suitable fuse links.(iv) CTs 50/5A for both the supplies.(v) DC Ammeter.(vi) DC Voltmeter.(vii) Push buttons.(viii) Indication Lamps.(ix) 2 over load+ earth leakage relay. 79 (x) Multi functional digital meter for KWH,KVA,KW,Amps,volts, frequency,power factor etc.(xi) SMPS Battery charger 12V, with trickle & Boost charging(xii) On/ Off switch.(xiii) Automatic/manual switch.(xiv) Hooter.(xv) Voltage sensing relay.(xvi) Six window enunciator for fault indications.(xvii) Electro magnetic relays.(xviii) Metering required in DG set :- A, V, Hz, KVA, KW, PF & KWH Metering required in mains :- A, V, Hz. 80 (F) Acoustic enclosure: CPCB approved enclosure is free standing floor mounted factory built and modular in construction to facilitate easy assembly at work site and will be drop over housing type. It will consist of acoustically treated panel housed in sheet steel will provide easy access for maintenance, repairs and operation. The enclosure is custom built to suit conditions, with the following features:-(a) Custom built product for various equipments, with ensure the optimum performance without duration. 81 (b) Rugged in construction maintenance free and modular designs which facilitate easy at site.(c) 16 SWG (1.6 mm) thick CRCA sheets to be used for enclosure panel to ensure longer life against weathering action. High quality acoustic insulation materials to be used as per IS 8183 for maximum sound absorption. Acoustic layers are supported by perforated sheets.(d) Sheet metal components of the enclosure should undergo various stages of surface treatment prior to painting which leads to be better life of the enclosure against eathering action.(e) Special paint treatment with pure polyester 82 powder/epoxy to be provided for better weather resistance.(f) Well designed ventilation system to be provided to pump up the heat in the chamber efficiently.(g) For effective acoustic / weather sealing a special type weather sealing gaskets, new frame rubber gaskets to be used.(h) Working space is to be provided around tube equipment for easy maintenance / repairs.(j) Necessary cut out provision for entry and exist of fuel lines cable to be incorporated in the enclosure as per the requirement.(k) A see through transparent window (glass or acrylic) in front of engine panel to be provided for monitoring the operation.(l) Ducting if required, bellows, mechanical hardware like locks, hinges fasteners etc to be provided.(m) Deliverables. 75 dBA @ 1 mtr at 75% load under free field conditions. The temp inside tee enclosure will be within as per manufacturers recommendations above ambient temp. 83 (n)The enclosure should be provided with bulk head light fitting for inside illumination(o) The batteries should be placed inside the enclosure beside the DG Set on a suitable insulated platform.(p) The DG Set should be provided with external Emergency stop push button.(q) The acoustic enclosure parts shall be of powder coated after pre treatment process.(r) The powder coating shade should be Genset Green. The base frame should be painted with epoxy based black shade. 84 Make for AMF PANEL: DG SET OEMMake for ACCOUSTIC PANEL: DG SET OEMThe following provisions are deemed to be included in the rate quoted forDG set:-(a) The quoted rate shall be deemed to be inclusive of first fill of lubricant oil and final successful acceptance test.(b) DHPP for testing purpose shall be supplied by the contractor without any extra cost to department.(c) The contractor shall arrange for artificial load for testing for final testing of DG Set at site and the cost is deemed to be including in above offer. 85 (c) The quoted rate shall be deemed to be inclusive of 12 hours test run at site including of one hour on 10% overload in presence of representative detailed by accepting Officer, all arrangements are to be made by thecontractor for tests.(d) Rate quoted shall be deemed to be included in making necessary holes to walls and making good the disturbed surfaces to match to original specification and connecting up all as specified and directed . 86 (G) Civil Works :- All civil works with PCC plat form and related tofoundations including of panel and equipments and making good theexisting structure of disturbed during installation and commissioning ofGenset. The depth of the foundation shall be minimum 300 mm with ant vibration pads or as recommended by the manufacturer. 87 M & L earthing complete with galvanised steel earth plate electrode 60cmx 60cmx 6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth strip 32 x 6mm dia, by means of nuts, bolts,check nuts and washer etc. of galvanised iron and earth lead protected by provision of GI pipe medium grade 40mm bore from earth electrode to test pointincl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4)and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed. 88 Note :- The cost of 7.5m long galvanised iron earth strip of 32 x 6mm size and protection pipe of 40mm bore GI light grade is deemed to be included in quoted unit rate. 89 PILE FOUNDATION,PILE CAP AND GRADE BEAM 90 450mm diaBoring for Bored cast in situ piles 16 metres in soil and getting out and disposal ofspoil to a distance out side MD Land using DMC method (Direct mud circulation) through rig mechine complete all as specified and directed. 91 500mm diaBoring for Bored cast in situ piles 16 metres in soil and getting out and disposal ofspoil to a distance out side MD Land using DMC method (Direct mud circulation) through rig mechine complete all as specified and directed. 92 Add/Deduct to above item No -58 450mm bore caste in situ piles for each metrecomplete all as specified and directed. 93 Add/Deduct to above item No -59500mm bore caste in situ piles for each metre complete all as specified and directed. 94 450mm diaBoring for Bored cast in situ pilesin Chiselling / cutting through for boring for cast in situ piles through rig mechine in soft rock and getting out and disposal of spoil to a distance out side MD Landcomplete all as specified and directed. 95 500mm diaBoring for Bored cast in situ pilesin Chiselling / cutting through for boring for cast in situ piles through rig mechine in soft rock and getting out and disposal of spoil to a distance out side MD Landcomplete all as specified and directed. 96 450mm diaBoring for Bored cast in situ pilesin Chiselling / diamond cutting through for boring for cast in situ piles through rig mechine in hard rock and getting out and disposal of spoil to a distance out side MD Land complete all as specified and directed. 97 500mm diaBoring for Bored cast in situ pilesin Chiselling / diamond cutting through for boring for cast in situ piles through rig mechine in hard rock and getting out and disposal of spoil to a distance out side MD Land complete all as specified and directed. 98 S&F TMT 10 mm and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed)not less than 0.9 mm dia conformig to Fe 500D CRS. and guide ring will be welded with main barscomplete all as specified and directed. 99 All as per item no above herein before but 6 mm dia and over upto including 10 mm dia in stirrups, spacersand binders. 100 M & L for design Mix RMC M-30 RCC inpile foundations as per derived depth complete all as specified and directed. 101 Complete Chiseling M-30 design mix concrete pile of dia 450mm of depth as required at site and removal complete all as specified and directed. 102 Chiseling M-30 design mix concrete pile of dia 500mm of depth as required at site and removal complete all as specified and directed. 103 The following Carrying out Initial Load Test on 450/500/600 mm dia. bored cast-in-situ piles as per IS-2911 (Part-IV) complete all as specified and as directed. 104 Vertical load test (compression), as per IS IS-2911 (Part-IV) for 450mm dia pile. complete all as specified and directed 105 Vertical load test (compression), as per IS IS-2911 (Part-IV) for 500mm dia pile.complete all as specified and directed 106 Lateral load test,as per IS-2911 (Part-IV) for 450mm dia pile .complete all as specified and directed 107 Lateral load test,as per IS-2911 (Part-IV) for 500mm dia pile.complete all as specified and directed 108 Carrying out Routine Load Test on 450/500/600mm dia. bored cast-in-situ piles as per IS-2911 (Part-IV) complete all as specified and as directed. 109 Vertical load test (compression), as per IS IS-2911 (Part-IV) for 450mm dia pile.complete all as specified and directed 110 Vertical load test (compression), as per IS IS-2911 (Part-IV) for 500mm dia pile.complete all as specified and directed 111 Lateral load test,as per IS-2911 (Part-IV) for 450mm dia pile.complete all as specified and directed 112 Lateral load test,as per IS-2911 (Part-IV) for 500mm dia pile.complete all as specified and directed 113 Integrate Test for all Routine piles .complete all as specified and directed 114 Excavating over areas in soft /loose soil, n exc 1.5 m deep and getting out complete all as specified and directed. 115 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m indepth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. 116 M&L for Plain Cement concrete Type B2 1:2:4 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed. 117 M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. 118 M & L for design Mix RMC M-30 RCCas inpile cap complete all as specified and directed. 119 S & F MS liner for piles of any size using MS sheet of any thickness all as directed by Engineer in charge. 120 M&L for Formwork to sides of concrete foundations, footings, Pile cap, grade beams bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter
