|
| 1 | Dismentling of W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer - in Charge |
| 2 | Dismantling of flushing cistern of all types (C.I/PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead |
| 3 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 4 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs ordash fastener shall be paid for separately).9.1.3 Kiln seasoned and chemically treated hollock wood |
| 5 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)9.5.2 Kiln seasoned and chemically treated hollock wood9.5.2.1 35 mm thick shutters |
| 6 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 7 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 8 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 9 | 13.43 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :13.43.1 Water thinnable cement primer |
| 10 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gm/litre ofapprovedmanufactureof required shade and colour complete as per manufacture\"s specification.13.41.1 Two or more coats on new work |
| 11 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 12 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:Float glass panes of nominal thickness 4 mm (weightnot less than 10kg/sqm) |
| 13 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 14 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm |
| 15 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer - in - Charge . Concealed work, including cutting chases and making good the walls etc. 18.8.2 20 mm nominal dia pipes |
| 16 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 17 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15 mm nominal bore |
| 18 | 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 19 | 18.58 Providing and fixing PTMT grating of approved quality and colour. 18.58.1 Circular type18.58.1.1 100 mm nominal dia |
| 20 | 18.74 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 18.74.2 15 mm nominal bore with 45 cm length |
| 21 | Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15 mm dia of Sona make with wall flange as directed and specified (Pipes will be measured and paid separately)(a) Supreme shower with arm |
| 22 | Providing and fixing brass stop cock of approved quality 18.16.220 mm nominal bore |
| 23 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved qual;ity conforming to IS :893118.53.1 15 mm nominal bore |
| 24 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete 17.28.1 Semi rigid pipe 17.28.1.1 32 mm dia |
| 25 | 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7.6 White Vitreous China Angle back wash basin size 400 x 400 mm with single 15 mm C.P. brass Pillar tap |
| 26 | 17.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 27 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in allcolours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.1 Double charge vitrified tile polished finish of size 11.41A.1.1 Size of Tile 600 x 600 mm |
| 28 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 29 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.3 Oval shape 450x350 mm (outer dimensions) |
| 30 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 31 | 8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.2.2 Granite stone slab colour black, Cherry/Ruby red8.2.2.2 Area of slab over 0.50 sqm |
| 32 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.17.18.1 10 litre capacity - White |
| 33 | Supplying , fitting and fixing Chrome plated (c.P.) sink cock of approved brand as directed and specified ( g.I. & C.P. pipes will be measured and paid separately) (I) Sona Brand a) Sink Cock upper / lower spout 15 mm |
| 34 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. |
| 35 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making goodthe walls wherever required :17.10.2 Kitchen sink without drain board, 17.10.2.1 610 x 510 mm bowl depth 200 mm |
| 36 | Providing drain with brick work in cement mortar in proportion 1 : 5 with half brick thick side wall and 100 mm thick C.C. ( 1 : 3 : 6)base over one brick flat soling including 15 mm thick cement plastering in prop 1 : 3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified . (ii) 300 mm wide and average 250 mm deep with bed slope 1 in 150 with initial depth of 100 mm |
| 37 | Supplying, fitting and fixing PVC pipes of 6 kg / cm 2 (Supreme/Prince) or other ISI approved including jointing, fitting and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified (a) in exposed surface or in trenches (ii) 110 mm dia |
| 38 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme / Prince) or other ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified (a) in exposed surface or trenches (ii) 110 mm dia |
| 39 | Supplying, fitting and fixingPVC plain Single Teeof (Supreme / Prince) or other ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified(ii) 110 mm dia |
| 40 | Supplying, fitting and fixing PVC pipes of 6 kg / cm 2 (Supreme/Prince) or other ISI approved including jointing, fitting and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified (a) in exposed surface or in trenches (ii) 50 mm dia |
| 41 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme / Prince) or other ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified (a) in exposed surface or trenches (ii) 50 mm dia |
