Tender For supply installation testing and commissioning Of 12 Mtr Highmast With 5 Nos Of 500W Led Flood Light At Machingal Bypass Junction Malappuram Municipality Under Annual Plan(Project No 794)- 1 Civil Work 2 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil 3 2.26.1Extra for every additional lift 1.5 m or part there of in excavation / banking excavatedor stacked materials.All kinds of soil 4 4.1.8 Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources) 5 5.9.1Centering and shuttering including strutting, etc. and removal of formfor:Foundations, footings, bases of columns, etc for mass concrete 6 5.22.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete upto plinth levelThermo - Mechanically Treatedbars of grade Fe-500D or more 7 5.1.2 Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mmnominal size derived from natural sources) 8 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 9 2.25Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundation etc. in layers not exceeding 20 cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 10 Electrical Work 11 90.15.2.3Supply installation testing and commissioning of High Mast using Octogaonal Polemade single/two sections of hot dip galvanised GI sheet 100mm top diameter, 360mmbottom diameter thickness 3mm mm suitable for wind speed as per IS 875 Part IIIwith head frame assembly two point suspension system with steel wire rope 5mm diadouble drum winching system w and including round arm galvanized luminarycarriage suitable to install 6/8 nos luminaries in symmetrical arrangement control gearbox and lighting spikes with single phase operation power tool installed inside thebase compartment including connector foundation bolt 4 nos fixed in existing RCCfoundation and junction box etc, complete 12 Meters 12 OD163040/2025-2026Supply Conveyance, installation, testing and commissioning of 500W LED Floodlight output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chipmake Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internalsurge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD less than 10%, power factor greater than 0.98,RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartmentshould be seperatly accessible for maintenance (LM 79&80 certificates fromNABL accredited Third party lab to be produced mentioning chip manufacturer) 13 OD163028/2025-2026Supply and installation of Twin unit aviation LED obstruction light with stand yellow-painted die-castaluminium alloy housing, red coloured polycarbonate dome and BC /EC lamp holder suitable for LEDlamp 14 90.14.1.2Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braidedcopper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame) 15 OD163105/2025-2026Fabrication and fixing of the Panel Board Stand with 2 legs made up of B classGI<br>pipe 32mm dia 1.8mtr. length. 32 mm dia G.I pipe ( medium class) 16 90.14.3.2Supply and providing heavy duty A section neoprene gasket in the panel boardUsection rubber beeding suitable for 1.60/ 2.00 mm sheet 17 OD163032/2025-2026Supply and fixing of 25 A 2 Pole AC 1 rated power contactor,25 A connector, DigitalTimer, suitable copper socket,2.5 sq.mm ISI marked FRLS PVC insulated single core copperconductor cable, 1.5 sq.mm ISI marked FRLS PVC insulated single core copper conductor cable, OBObettermann makes V25-B+C/1+ NPE (switching/lighting protection) for single phase protection. 18 OD163030/2025-2026Supply and fixing of 2 nos. of 25A 3 Pole AC 1 rated power contactor, Selectorswitch for motor control, supply and fixing flush head push button NO-NC, 1.5 sq. mm ISI markedFRLS PVC insulated single core copper conductor cable and 2.5 sq. mm ISI marked FRLS PVCinsulated single core copper conductor cable 19 OD163027/2025-2026Supply and fixing HRC fuse base of 20/32A using suitable nut and bolt, 32 A 2-Way neutral links mounted on DMC/SMC base and 2.5 sq.mm ISI marked FRLS PVC insulated single core copper conductor cable. 20 1.21.5Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm 21 2.14.2Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps 22 2.10.1Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 23 2.10.3Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, C curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Double pole 24 2.12.1Supplying and fixing following rating, double pole, 240 volts, isolator in the existingMCB DB complete with connections, testing and commissioning etc. as required.40 amps 25 90.6.5.13Supply and drawing the following sizes of multi-core PVC insulated & FRLSPVC sheathed 650/1100 V grade copper conductor round flexible cables conformingto IS 694 part I 1960 in the existing surface / recess conduit as required includinggiving necessary connections of the following sizes.3 core 4.00 sq mm 26 90.6.5.11Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sq mm 27 5.3Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick includingaccessories, and providing masonry enclosure with cover plate having lockingarrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke andsalt ) as required. 28 90.16.4.2Supply and clamping the following sizes of strips on surface of wall / parapet/ existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good the damages, colour washing etc. as required ( for vertical run).25 x 3 mm GI strip 29 90.16.1.3Supply and drawing bare earthing conductors of the following sizes along withwiring/ cables and giving connection as required3.15 mm copper conductor ( 10SWG) 30 90.16.5.3Supply of superior quality copper earth socket for the following size of earthconductor including crimping etc. as required.3.15 mm (10 SWG) 31 90.12.5.14Supply & laying of one number PVC insulated and PVC sheathed armouredaluminium power cable of 1.1KV grade of the following sizes in the existing RCC/HUME / STONE WARE/ GI/ DWC pipe as required.3 core 10 sq mm 32 90.12.9.2Supplying, laying and jointing of the following sizes of double wall corrugated(DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanicalprotection to underground power cables with all required accessories in ground in theexisting trench50/38 mm or nearest sizeNet Total 10.000metre 33 9.1.2Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm) 34 OD163033/2025-2026ACP Sheet Name Board 35 OD163031/2025-2026Fabrication,supply, conveyance and installation of granite board indicating the cost Involved,commencement,completion and inauguration. 36 Connection charges - KSEB
