Tender For Construction Work Of The Road Of Narhauli Village Located On Bharatpur Road In Mathura District - Earth Work In Surface Excavation Not Exceeding 30 Cm In Depth But Exceeding 1.5 M In Width As Well As 10 Sqm On Plan Including Getting Out And Dis, mathura-Uttar Pradesh

Tender For Construction Work Of The Road Of Narhauli Village Located On Bharatpur Road In Mathura District - Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift up to 1.5 m, as directed by Engineer-in-Charge: DSR 2023 I.NO 2.1 2 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). DSR2023 I.NO 4.1.8 3 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 2023 I.NO 6.1.1 4 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) DSR 2023 I.NO 13.4.1 5 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 2023 I.NO 4.1.3 6 Providing, laying spreading & compacting of granular sub base by providing close graded (Fr-1) materials, sprading in uniform layers with Mortor Graded on prepared surface, mixing by mix in placed method with Rotovater at OMC and compacting with in layers with smooth wheeled Vibratory Roller to achieve the desired density, complete as per MoR &H clause 401& as directed by Engineer Incharge including all machine charges & including all labour, T& P etc req for proper completion of work. Analysis rate.(As per MORTH 502 and PWD SOR 2022-23) 7 Supply & Laying ofprecast concrete Block ( Interlocking tiles) for paving of thickness 100mm rubber mould grey (Compressive strength not less then 30Mpa as specified in IS:15658 and weight 4.50kg)as jindal,naval or equivalant Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand all complete work as specified in IS 15658:2006. as directed by E/I. SN0.16 New item page 52 chapter 20 UPPWDSOR 2022-23 8 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) dsr 2023 i.no 5.1.2 9 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. dsr 2023 i.no 5.22A.6 10 Supply ofSolarAIO SinglepieceHighpressureDiecast (LM6Alloy)17WAluminiumhousingappearanceofSolar AIOshallbetraditionalStreetLight, IP65&IK08,suitable for OD 50/60mm bracket, having Min 3000 lumens, suitable for24hrs(2Nights)Autonomyanditsbackupcalculation sheet shall be approved by Consultant Dimming Profile :•From Dusk– First05hourssensorenabled with30% brightness level• Next 05Hours sensor disabled and fixed at 30% Brightness level•Next2hours/dawn-Sensorenabledwith30%brightness levelLithiumpherrophosphate Battery capacity min 20Ah@12.8V or 256watthour&shallbeoffreshmanufacturedbattery (Not re-used cells) Battery Temp range -20-+60℃and panel capacitymin35Wp,CRI>=70,EfficacyMin>175lm/Wis MUST, system wattage should not be more than 17W ± 5%, ifwattagesincreasesthenthesizeofbattery &panelshall alsobeincreasedinsimilarpercentagetomaintainequal autonomy of the system. Life class of LED System 50000hrs@L70,LEDMake- CREE/ NICHIA/ LUMILEDS /OSRAM. CE Certified, charger efficiency >90% and standards IEC62109-1, IEC61547, CISPR15,IEC62093,IEC61347-2-13,EN50530,IEC62384 ThePVmoduleshouldbemadeupof crystallinesilicon solar cells Mono-Crystallineand musthave acertificate of testing conforming to IEC 61215 Edition II / BIS 14286 & IEC 61730-1,2IEC60598,Operatingtemp0DegreeCto50 Degree C, certifying above givenprameters all reports shall be from In-house NABL or IECQ or any international accredited Laboratory, Complete luminaire /battery/panel/charge controllermustbe BIS accredited (If applicable)and asperUPPWDApproved Make as per dierction of E/I.. With five yeart warrenty 11 Supply & fixing of 7mGI Octagonal Pole of approved make (topdia70mm,bottomdia130mmandbaseplate12mm thick)having3mmthicknesswithsinglearmbracket(1m length) onRCC foundationincludingthecostof foundation, foundation bolts, excavation & back filling and required T&P complete in all respect.

INR 1770 /-

INR 38.03 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB